-
Bush Hog 3227 QT - page 1
OPERATION l l MAINTENANCE 907 $4.00 50057987 2 4 2 7 , 2 4 4 7 , 2 8 4 7 & 3 2 2 7 Q T F r o n t E n d L o a d e r s O p e r a t o r ’ s M a n u a l B U S H H O G ® ...
-
Bush Hog 3227 QT - page 2
CONGRATULATIONS! You have invested in the best implement of its type on the market today. The care you give your Bush Hog implement will greatly determine your satisfaction with its performance and its service life. We urge a careful study of this manual to provide you with a thorough understanding of your new implement before operating, as well as ...
-
Bush Hog 3227 QT - page 3
2427, 2447, 2847 & 3227 QT TABLE OF CONTENTS SECTION/PARA PAGE Warranty .....................................................3 Dealer Preparation Check List ....................4 Safety Precautions ......................................5 Federal Laws & Regulations .......................7 I INTRODUCTION & DESCRIPTI ON ...........8 1-1 I ...
-
Bush Hog 3227 QT - page 4
LIMITED WARRANTY OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an authorized Bush Hog dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year for non-commercial, state, and municipalities’ use and ninety (90) days for comme ...
-
Bush Hog 3227 QT - page 5
DEALER PREPARATION CHECK LIST 2427, 2447, 2847 & 3227 QT LOADERS BEFORE DELIVERING MACHINE - The following check list should be completed. Use the Operator’s Manual as a guide. o Machine properly assembled. o All safety decals readable. (See decal page) o All bolts tightened to torque specifications given in torque chart. o Machine operates p ...
-
Bush Hog 3227 QT - page 6
IMPORTANT SAFETY PRECAUTIONS This symbol is used to call attention to safe- ty precautions that should be followed by the operator to avoid accidents. When you see this symbol, carefully read the message that follows and heed its advice. Failure to comply with safety precautions could result in serious bodily injury. In addition to the design and c ...
-
Bush Hog 3227 QT - page 7
10. Before disconnecting hydraulic lines, relieve all hydraulic pressure. 11. Do not tamper with the relief valve setting. The relief valve is pre-set at the factory. Changing the setting can cause overloading the loader and tractor and serious operator injury may result. 12. Always wear safety goggles when repairing or servicing machine. 13. When ...
-
Bush Hog 3227 QT - page 8
IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING EMPLOYERS, EMPLOYEES AND OPERATIONS. *(This section is intended to explain in broad terms the concept and effect of the following federal laws and regulations. It is not intended as a legal interpretation of the laws and should not be considered as such). U.S. Public Law 91-596 (The Williams-Steige ...
-
Bush Hog 3227 QT - page 9
SECTION I INTRODUCTION AND DESCRIPTION 1-1 INTRODUCTION We are pleased to have you as a Bush Hog cus- tomer. Your Front End Loader has been carefully designed to give maximum service with minimum down time. This manual is provided to give you the necessary operating and maintenance instructions for keeping your front end loader in top operating con ...
-
Bush Hog 3227 QT - page 10
SERIES LOADER 2427QT 2447QT 2847QT 3227QT A. Ma xim um Lif t Hei ght - Mea sur ed at Pi vot P in 117 in. 117 in. 137 in. 143 in. B. Maximum Lift Height - Under Level Bucket 108 in. 108 in. 128 in. 134 in. C. Clearance with Attachment Dumped 45° 89 in. 89 in. 109 in. 115 in. D. Reach at Maximum Height 26 in. 31 in. 28 in. 28 in. E. Maximum Dump Ang ...
-
Bush Hog 3227 QT - page 11
SECTION II LOADER MOUNTING AND DISMOUNTING TRACTORS THAT HAVE MOVABLE AXLES MUST BE SET FORWARD IN THE LONG WHEEL- BASE POSITION AS SHOWN IN FIGURE 2-1 TO PREVENT EXCESSIVE LEVERAGE BEING EXERTED ON THE TRACTOR FRAME. FAILURE TO DO SO CAN RESULT IN PERSONAL INJURY AND EQUIPMENT DAMAGE. REFER TO TRAC- TOR OPERATOR’S MANUAL FOR ABOVE PRO- CEDURES A ...
-
Bush Hog 3227 QT - page 12
USE CAUTION WHEN MOUNTING LOADERS EQUIPPED WITH OPTIONAL CONTROL VALVE ON TRACTORS EQUIPPED WITH CANOPY. RAISING LOADER SUBFRAME TOO HIGH CAN PINCH HAND BETWEEN CONTROL HANDLE AND CANOPY CAUSING INJURY. WARNING D. With tractor at idle speed, carefully act ivate boom cylinders to raise/lower cross tube until it aligns with front bracket channel. E. ...
-
Bush Hog 3227 QT - page 13
Figure 2-6 J. Secure hydraulic hoses to tractor to prevent interference. It is recommended that hoses be rout- ed under tractor operator’s platform. K. Extend and retract both sets of cylinders beginning with short strokes. Gradually increase the length of stroke until cylinders “bottom out” in each direction. Hold valve open with cylinders ? ...
-
Bush Hog 3227 QT - page 14
C. Lower boom until parking stands contact ground. D. Extend bucket cylinders until cutting edge of bucket is frimly on the ground. E. Remove pin from mounting bracket. G. With tracto r at idle speed, roll bucket back until subframe raises up off rear bracket. H. With tractor at idle speed, carefully activate boom cylinder until cross tube is fre e ...
-
Bush Hog 3227 QT - page 15
FILLING THE BUCKET Approach and enter the pile with a level bucket. Loaders with 1-lever control, ease lever back and toward you to lift and rollback the bucket. Loaders with 2-lever controls, ease both levers back to lift and rollback the bucket. The lift and rollback of the bucket will increase effi- ciency because... ...a level bucket throughout ...
-
Bush Hog 3227 QT - page 16
CARRYING THE LOAD Position the bucket as low as possible below the level of the tractor hood for maximum stability and visibility, whether the bucket is loaded or empty. Use extreme caution when operating the loader on a slope and keep the bucket as low as possible. This keeps the bucket and tractor center of gravity low and will provide maximum tr ...
-
Bush Hog 3227 QT - page 17
OPERATING WITH FLOAT CONTROL During hard surface operation, keep the bucket level and put the lift control in the float position to permit the bucket to float on the working surface. If hydraulic down pressure is exerted on the bucket, it will wear faster than normal. FLOAT The float will also prevent the mixing of surface material with stockpile m ...
-
Bush Hog 3227 QT - page 18
PEELING AND SCRAPING BACKFILLING 6” Us e a sl igh t buc ket ang le , tr ave l for war d, and hol d the li ft c on tro l fo rw ard to sta rt t he c ut . Ma ke a sh ort , an gl e cu t a pp rox im ate ly 6” de ep an d b re ak- ou t c lea nl y. With the bucket level, start a cut at the notch approx- imately 2” deep. Hold the depth by feathering t ...
-
Bush Hog 3227 QT - page 19
Leave dirt in the bucket because dumping on each pass wastes time. Operate at right angles to the ditch. Take as big a bite as the tractor can handle without lugging down. DITCH SOIL PILE Leave dirt which drifts over the side of the bucket for final clean-up. DITCH Pile dirt on the high side for easier backfilling on a slope. HANDLING LARGE HEAVY O ...
-
Bush Hog 3227 QT - page 20
3-4 FORK LIFT OPERATION WARNING TO AVOID SERIOUS INJURY OR DEATH: H H NE VER LIFT LARGE ROUND HAY BALES OR OTHER LOADS ON THE FORK LIFT ATTACHMENT THAT C O U L D R O L L B A C K O N T O T R A C - TOR OPERATOR AREA. H H NE VER USE FORK LIFT ATTACH- MENT TO LIFT OR SUPPORT PEOPLE. H H TRA NSPORT LOADS LOW AND SLOW. H H AV OID CONTACT WITH POWER LINES ...
-
Bush Hog 3227 QT - page 21
SECTION IV MAINTENANCE 4-1 MAINTENANCE CHECK LIST Perform scheduled maintenance as outlined below. Lower machine to ground, turn off tractor, and set parking brake before doing maintenance inspections or work. All bolts should be torqued as recommend- ed in torque chart unless otherwise indicated. BEFORE EACH USE 1. Inspect hydraulic lines and fitt ...
-
Bush Hog 3227 QT - page 22
4-3 HYDRAULIC SYSTEM PRESSURE REQUIREMENTS A tractor hydraulic system pressure setting of 2500 psi is recommended for maximum efficiency and ser- vice. Do not exceed 3000 psi as this will damage components possibly causing serious injury. The Bush Hog control valve is pre-set at the factory and should not be adjusted. 4-4 TROUBLESHOOTING Troublesho ...
-
Bush Hog 3227 QT - page 23
TABLE 4-1 TROUBLESHOOTING PROCEDURES PROBLEM POSSIBLE CAUSE REMEDY Loader slow and/or will not dump. Hydraulic oil to heavy. Change to proper oil. Oil filter plugged. Clean or replace filter. Hydraulic pump worn. Repair or replace pump. Oil line restricted or leaking. Check all hoses and tubes for leaks, damage or restrictions. Replace damaged or r ...
-
Bush Hog 3227 QT - page 24
SECTION V ASSEMBLY 1. Do not lift heavy parts or assemblies. Use crane, jack, tackle, fork trucks, or other mechanical devices. 2 Select an area for assembly that is clean and free of any debris which might cause persons working on the assembly to trip. 3. Arrange parts to be assembled neatly in the work area and have tools or other mechanical assi ...
-
Bush Hog 3227 QT - page 25
F. Connect hydraulic hoses to loader as shown in Figure 5-2. If optional hydraulic valve is used, refer to paragraphs 5-2 and 5-3 for valve and stand assembly instructions. G. Install cuffs, pins, washers, bolts, and nuts as shown depending on your particular model loader. (Figure 5-3) Figure 5-2 Tractor Hydraulic Kit Straight Adaptor 1/2” NPT to ...
-
Bush Hog 3227 QT - page 26
5-2 OPTIONAL HYDRAULIC VALVE STAND ASSEMBLY (Figure 5-4) A. Attach mounting plate to loader frame using two 5/8 x 5-1/2” bolts, flatwashers, lockwashers and nuts. Note that this plate may be rotated 180° to allow three different mounting tube heights. B. Attach mounting bracket to plate using two 1/2 x 1-1/2” bolts, lockwashers and nuts. C. At ...
-
Bush Hog 3227 QT - page 27
5-3 OPTIONAL HYDRAULIC VALVE PLUMBING INSTRUCTIONS D. Remove open center plug. E. Install the closed center plug furnished with valve. Note: When converting to closed center con- figuration open center plug is removed from valve and installed in sleeve of closed center plug assem- bly. F. Install valve operational decal on valve shield. A. Mount va ...
-
Bush Hog 3227 QT - page 28
IMPORTANT When loader hydraulics are disconnected from tractor hydraulics, hoses A & B must be connected to complete tractor hydraulic circuit. FAILURE TO DO THIS WILL CAUSE SERIOUS DAMAGE TO TRACTOR HYDRAULIC SYSTEM. Power Beyond Plug To Pressurized Return Inlet To Sump Inlet (Use Long Hose Here) To Pressure Inlet B C A These hoses to be furni ...
-
Bush Hog 3227 QT - page 29
5-5 FORK LIFT OPTION Raise positioning lock pins at the top of each fork. Place fork in the middle of the frame over the notch in the lower edge. slide forks to desired positions and lower pins to lock forks in place. Mainframe Fork Eccentric Nut Frame Assembly Long Spear Short Spears 28 5-6 BALE SPEAR OPTION In ser t lon g spe ar in to top of fr a ...
-
Bush Hog 3227 QT - page 30
5-7 OPTIONAL BUCKET ITEMS ASSEMBLY 29 SPILL GUARD ATTACHMENT 1. Place spill guard on bucket & center. 2. Mark hole centers for attaching fasteners. Allow clearance for side cutting edges on bolts in side plates if necessary. 3. Re mo ve sp il l gu ar d an d dr il l 9/ 16 ” ho le s. In st al l sp il l gu ar d an d t or qu e fa st en er s pe r ...
-
Bush Hog 3227 QT - page 31
SAFETY DECALS To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damages can occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, provide safety decals for any of our products in the field at no charge. Contact your authorized Bush Hog dealer for more infor ...
-
Bush Hog 3227 QT - page 32
B O L T D I A M E T E R W R E N C H ( I N . ) “ B ” A N D S A E S A E S A E S I Z E ( I N . ) “ A ” T H R E A D S I Z E G R A D E 2 G R A D E 5 G R A D E 8 7/16 1/4 - 2O UNC 6 (7) 8 (11) 12 (16) 7/16 1/4 - 28 UNF 6 (8) 10 (13) 14 (18) 1/2 5/16 - 18 UNC 11 (15) 17 (23) 25 (33) 1/2 5/16 - 24 UNF 13 (17) 19 (26) 27 (37) 9/16 3/8 - 16 UNC 20 (2 ...
-
Bush Hog 3227 QT - page 33
P.O. Box 1039 l l Selma, AL 36702-1039 Telephone (334) 874-2700 l l www.bushhog.com ...
Do you have a question concerning Bush Hog 3227 QT?
Use the form below
If you did not solve your problem by using a manual Bush Hog 3227 QT, ask a question using the form below. If a user had a similar problem with Bush Hog 3227 QT it is likely that he will want to share the way to solve it.