English dropdown-ico

Manual Smeg PGA75SC3

20 pages 1.1 mb
Download

Go to site of 20

Summary
  • Smeg PGA75SC3 - page 1

    Summary 1 INSTRUCTIONS FOR SAFE AND PROPER USE ________________ 4 2 POSITIONING OF THE HOB ________________________________ 6 3 GAS CONNECTION ______________________________________ 12 4 ADJUSTMENT TO DIFFERENT TYPES OF GAS _______________ 14 5 FINAL OPERATIONS _____________________________________ 16 6 USING THE HOB _______________________________ ...

  • Smeg PGA75SC3 - page 2

    Introduction 1 INSTR UCTIONS FOR SAFE AND PR OPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS EN TIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE HOB. ALSO KEEP THE SERIES OF NOZZLES SUPPLIED. INSTALLATI ...

  • Smeg PGA75SC3 - page 3

    Introduction THE APPLIANCE DATA PLATE, WITH TECHNICAL DATA, REGISTRATION NUMBER AND BRAND NAME, IS POSITIONED AT A VISIBLE POINT UNDER THE SAFETY COVER. THE DATA PLATE ON THE PROTECTIVE COVER MUST NEVER BE REMOVED . DO NOT PUT PANS WITHOUT PERFECTLY PERFECTLY SMOOTH AND FLAT BOTTOMS ON THE HOB PANSTAND GRIDS. DO NOT USE COOKING RECEPTACLES THAT EXT ...

  • Smeg PGA75SC3 - page 4

    Instructions for the installer 6 2 POSITIONING OF THE HOB The following operation requires buildi ng and/or carpentry work so must be carried out by a competent tradesman. Installation can be carried out on various materials such as masonry, metal, solid wood or plastic laminat ed wood, as long as they are heat- resistant (T 90°C). 2.1 Attachment ...

  • Smeg PGA75SC3 - page 5

    Instructions for the installer 2.2 Attachment to support structure, flush-mounting model Create an opening with the dimensions shown in the figure in the work surface, observing a minimum distance of 50 mm from the rear edge. 1) The lower part of the protective cover must be fully accessible when the appliance is installed. This appliance can be in ...

  • Smeg PGA75SC3 - page 6

    Instructions for the installer 8 Important: Other types of insta llation will only be possible under the manufacturer's supervision. Overall dimensions: location of gas and electrical connection points (all measures in mm). Caution: surface temperature underneath may exceed 125 degrees C. To avoid a hazard, under-bench access must be restricte ...

  • Smeg PGA75SC3 - page 7

    Instructions for the installer 2.3 Clearance above and around domestic appliances Extract from AS5601 REQUIREMENTS 1 Overhead clearances – (Measurement A ) Range hoods and exhaust fans shall be in stalled in accordance with the manufacturer’s instructions. However, in no case shall the clearance between the highest part of the hob of the cookin ...

  • Smeg PGA75SC3 - page 8

    Instructions for the installer 10 2 Side clearances – (Measurements B & C) Where B , measured from the per iphery of the nearest burner to any vertical combustible surface , is less than 200 mm , the surface shall be protected in accordance with Clause 5.12.1.2 to a height C of not less than 150 mm above the hob for the full dimension (width ...

  • Smeg PGA75SC3 - page 9

    Instructions for the installer Discharge of combustion products Discharge of combustion products must be guaranteed by means of hoods connected to a natural draught fl ue with certain efficiency, or by means of forced aspiration. An efficient aspiration system requires careful planning by a specialist capable of installing it, respecting t he posit ...

  • Smeg PGA75SC3 - page 10

    Instructions for the installer 12 3 GAS CONNECTION This appliance is suitable for installation with Natural Gas or LPG (propane). Refer to page 12 for the relevant burner pressure and appropriate injector sizes. When the appliance is to be connected to Natural Gas then the pressure regulator supplied must be fitted to the gas inlet. A te st point ( ...

  • Smeg PGA75SC3 - page 11

    Instructions for the installer 3.1 Electrical connection Make sure that the voltage and capacit y of the power supply cable conform to the data shown on the plate loca ted under the protective cover. Do not remove this plat e for any reason . The power supply cable plug and the wa ll socket must be of the same type and conform to the current electr ...

  • Smeg PGA75SC3 - page 12

    Instructions for the installer 14 4 ADJUSTMENT T O DIFFERENT TYPES OF GAS Before performing any cleaning or maintenance work, unplug the appliance from the mains. The hob of the cooker is adj usted for use with either natural gas at a pressure of 1.0 kPa . If used with other types of gas, you have to replace the nozzles, then adjust the minimum fla ...

  • Smeg PGA75SC3 - page 13

    Instructions for the installer 4.2 Burner and nozzle characteristics table Burner ULPG – 2.75 kPa Nominal gas Consumption (MJ/h) Injector (mm) Auxiliary (1) 3.9 0.54 Semi rapid (2) 6.3 0.68 Ultra Rapid (3) 13.5 1.00 Burner NG – 1.0 kPa Nominal gas Consumption (MJ/h) Injector (mm) Auxiliary (1) 3.9 0.90 Semi rapid (2) 7.5 1.20 Ultra Rapid (3) 15 ...

  • Smeg PGA75SC3 - page 14

    Instructions for the installer 16 5 FINAL OPERA TIONS After carrying out the above adjustments, remount in reverse order to the instructions given in paragraph “3.1 Replacement of nozzles on the hob”. After having regulated the device wit h gas other than the one tested, replace the label located on the guar d with the one that corresponds to t ...

  • Smeg PGA75SC3 - page 15

    Instructions for the user 6 USING THE HOB 6.1 Ignition of the burners Before turning on the burners, make su re that the flame-spreader crowns and respective caps are properly fi tted in their housings. Ensure the flame-spreader holes A are aligned with the ignition plugs and the thermocouples. Panstand grid B , available upon request, is intended ...

  • Smeg PGA75SC3 - page 16

    Instructions for the user 18 6.2 Practical advice for using the burners For better use of the burners and lowe r gas consumption, use covered cooking receptacles that have a flat, smooth bottom and are proportional in size to the burner to prevent the flame from licking the sides (see paragraph “ 6.3 Diameter of receptacles ”). When water reach ...

  • Smeg PGA75SC3 - page 17

    Instructions for the user 7 CLEANING AND MAINTENANCE Before any intervention, disconnect the appliance from the mains. 7.1 Cleaning the stainless steel To keep stainless steel in good c ondition it should be cleaned regularly after use. Let it cool first. 7.1.1 Routine daily cleaning To clean and preserve the stainl ess steel surfaces, always use o ...

  • Smeg PGA75SC3 - page 18

    Instructions for the user 20 7.3 Preventive maintenance This appliance does not need any s pecial maintenance. However, a few simple operations have to be ca rried out periodically to prevent malfunctioning: Burners: the burners must be cleaned peri odically to ensure correct combustion; make sure that a ll the openings and flame ports are clean an ...

  • Smeg PGA75SC3 - page 19

    ...

  • Smeg PGA75SC3 - page 20

    914773032/ C ...

Manufacturer Smeg Category Range

Documents that we receive from a manufacturer of a Smeg PGA75SC3 can be divided into several groups. They are, among others:
- Smeg technical drawings
- PGA75SC3 manuals
- Smeg product data sheets
- information booklets
- or energy labels Smeg PGA75SC3
All of them are important, but the most important information from the point of view of use of the device are in the user manual Smeg PGA75SC3.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Smeg PGA75SC3, service manual, brief instructions and user manuals Smeg PGA75SC3. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Smeg PGA75SC3.

Similar manuals

A complete manual for the device Smeg PGA75SC3, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Smeg PGA75SC3 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Smeg PGA75SC3.

A complete Smeg manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Smeg PGA75SC3 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Smeg PGA75SC3, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Smeg PGA75SC3, that we can find in the current document
3. Tips how to use the basic functions of the device Smeg PGA75SC3 - which should help us in our first steps of using Smeg PGA75SC3
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Smeg PGA75SC3
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Smeg PGA75SC3 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Smeg PGA75SC3?

Use the form below

If you did not solve your problem by using a manual Smeg PGA75SC3, ask a question using the form below. If a user had a similar problem with Smeg PGA75SC3 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)