English dropdown-ico

Manual Vulcan-Hart CMR34

12 pages 0.52 mb
Download

Go to site of 12

Summary
  • Vulcan-Hart CMR34 - page 1

    VULCAN-HART COMPANY, P.O. BOX 696, LOUISVILLE, KY 40201-0696, TEL. (502) 778-2791 FORM 30805, Rev. A (8-95) MODEL CMR34 GAS CHEESEMEL TER ML-52198 INST ALLA TION & OPERA TION MANUAL ...

  • Vulcan-Hart CMR34 - page 2

    — 2 — IMPORT ANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE OB ...

  • Vulcan-Hart CMR34 - page 3

    — 3 — Installation, Operation and Care of MODEL CMR34 GAS CHEESEMEL TER KEEP THIS MANUAL FOR FUTURE REFERENCE GENERAL Your Vulcan-Hart Gas Cheesemelter is suitable for use in restaurant, commercial or institutional kitchens. The cheesemelter is produced with quality workmanship and material. Proper installation, usage and maintenance of your ch ...

  • Vulcan-Hart CMR34 - page 4

    — 4 — LOCATION Do not obstruct the air flow into and around the cheesemelter. This air flow is necessary for proper combustion of gases and for ventilation of the cheesemelter. Do not obstruct the flow of flue gases from the flue duct of the cheesemelter. It is recommended that the flue gases be ventilated to the outside of the building through ...

  • Vulcan-Hart CMR34 - page 5

    — 5 — INSTALLATION CODES AND STANDARDS The cheesemelter must be installed in accordance with: 1. State and local codes. 2. In USA . . . National Fuel Gas Code, ANSI Z223.1 (latest edition) available from the American Gas Association, Inc., 1515 Wilson Blvd., Arlington, VA 22209. In Canada . . . Canadian Standard CAN/CGA-B149.1 Installation for ...

  • Vulcan-Hart CMR34 - page 6

    — 6 — 4. Replace back top(s) and top castings on range. 5. After unpacking, remove the rack, drip pan and drip pan insert from the cheesemelter. 6. Make sure the mounting brackets are firmly attached to the top of the cheesemelter. Carefully lift the cheesemelter so that the cheesemelter support brackets are approximately one inch above the flu ...

  • Vulcan-Hart CMR34 - page 7

    — 7 — Fig. 5 Fig. 6 5. Line up holes on top brackets. Attach self-tapping screw to each top bracket, and attach 3 / 8 -16 bolt to each top bracket. Bolt thread through weld-nut on rail (beam support). 6. Reassemble bottom cover on cheesemelter (8 screws). 7. Attach shelf to back riser if included. GAS CONNECTIONS CAUTION: All gas supply connect ...

  • Vulcan-Hart CMR34 - page 8

    — 8 — Standard cheesemelters for use with natural gas are equipped with fixed orifices and a pressure regulator with a preset outlet pressure of 6" W.C. (water column). Standard cheesemelters for use with propane gas are equipped with fixed orifices and a pressure regulator with a preset outlet pressure of 10" W.C. Once the regulator ...

  • Vulcan-Hart CMR34 - page 9

    — 9 — OPERA TION WARNING: THE CHEESEMELTER AND ITS PARTS ARE HOT. BE CAREFUL WHEN OPERATING, CLEANING OR SERVICING THE CHEESEMELTER. CONTROLS — (Fig. 9) Fig. 9 Burner Valve — The burner valve regulates the flow of gas throughout the cheesemelter. Gas flow is increased by turning the valve counterclockwise. After preheating, the maximum outp ...

  • Vulcan-Hart CMR34 - page 10

    — 10 — LIGHTING THE PILOT LIGHT 1. Turn on the main gas supply. 2. Turn on the burner valve and purge air from the line. Turn the burner valve off, wait five minutes. 3. Using a taper, light the pilots (Fig. 10). 4. If the pilots fail to light, turn off the gas, wait five minutes and repeat Steps 1 through 3. 5. Turn burner valve on for ignitio ...

  • Vulcan-Hart CMR34 - page 11

    — 11 — LOADING AND UNLOADING Place the rack in the desired position. Pull the rack out for loading. Load as quickly as possible and avoid spillage. Push the rack into place and cook for the appropriate time. Lower and pull the rack out for unloading. CLEANING PermaFinish surfaces can be cleaned using a cloth with detergent solution. An occasion ...

  • Vulcan-Hart CMR34 - page 12

    — 12 — TROUBLESHOOTING PROBLEM Uneven heating Side burning Too much top heat Uneven heat side-to-side Uneven heat front-to-back Dried out products Pilot outage Poor ignition POSSIBLE CAUSES 1. Temperature too low 2. Improper operation of cheesemelter 3. Fluctuating gas pressure 1. Temperature too high 2. Faulty ventilation 3. Excessive heat inp ...

Manufacturer Vulcan-Hart Category Fondue Maker

Documents that we receive from a manufacturer of a Vulcan-Hart CMR34 can be divided into several groups. They are, among others:
- Vulcan-Hart technical drawings
- CMR34 manuals
- Vulcan-Hart product data sheets
- information booklets
- or energy labels Vulcan-Hart CMR34
All of them are important, but the most important information from the point of view of use of the device are in the user manual Vulcan-Hart CMR34.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Vulcan-Hart CMR34, service manual, brief instructions and user manuals Vulcan-Hart CMR34. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Vulcan-Hart CMR34.

Similar manuals

A complete manual for the device Vulcan-Hart CMR34, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Vulcan-Hart CMR34 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Vulcan-Hart CMR34.

A complete Vulcan-Hart manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Vulcan-Hart CMR34 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Vulcan-Hart CMR34, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Vulcan-Hart CMR34, that we can find in the current document
3. Tips how to use the basic functions of the device Vulcan-Hart CMR34 - which should help us in our first steps of using Vulcan-Hart CMR34
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Vulcan-Hart CMR34
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Vulcan-Hart CMR34 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Vulcan-Hart CMR34?

Use the form below

If you did not solve your problem by using a manual Vulcan-Hart CMR34, ask a question using the form below. If a user had a similar problem with Vulcan-Hart CMR34 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)