English dropdown-ico

Manual GE 206C1559P197

32 pages 3.57 mb
Download

Go to site of 32

Summary
  • GE 206C1559P197 - page 1

    GE Consumer & Industrial Appliances Installation Instructions Built -In Dishw asher If you have questions, call 800. GE. CARES (800.432.2737) or visit our Website at: GE Appliances.com. In Canada, please call 1.800.561.3344 or visit www .geappliances.ca IMP ORT ANT – The dishwasher MUST be installed to allow for future r emoval fr om the encl ...

  • GE 206C1559P197 - page 2

    T OOLS YOU WILL NEED: ■ ■ Phillips-head screwdriver ■ ■ 1/4" and 5/16" nutdriver ■ ■ 6" Adjustable wrench ■ ■ Level ■ ■ Carpenter's square ■ ■ Measuring tape ■ ■ Safety glasses ■ ■ Flashlight ■ ■ Bucket to catch water when fl ushing the line ■ ■ 15/16" socket (optional for skid remov ...

  • GE 206C1559P197 - page 3

    Method 1 – Air Gap with Waste Tee or Disposer An air gap must be used when required by local codes and or di- nances. The air gap must be installed according to manufacturer ’s instructions. PREP ARE DISHW ASHER ENCLOSURE • The rough cabinet opening must be at least 24" deep, 24" wide and approximately 34-1/2" high fr om floor ...

  • GE 206C1559P197 - page 4

    For models equipped with power cor d: Do not modify the plug provided with the appliance; if it will not fit the outlet , have a proper outlet installed by a qualified technician. Cabinet Preparation & Wire Routing • The wiring may enter the opening from either side, r ear or the floor within the shaded area illustrated above in Figur e E and ...

  • GE 206C1559P197 - page 5

    PREP ARE HO T W A TER LINE • The line may enter from either side, r ear or floor within the shaded area shown in Figur e F . • The line may pass through the same hole as the electrical cable and drain hose. Or , cut an additional 1-1/2" diameter hole to accommodate the water line. If power cor d with plug is used, water line must not pass ...

  • GE 206C1559P197 - page 6

    Dishwasher Installation Figure G • Screw leveling legs back into the dishw asher frame, approximately 1/8" fr om frame as shown. Approx. 1/8" STEP 3: REMOVE WOOD BASE, INST ALL LEVELING LEGS IMP ORT ANT – Do not kick off wood base! Damage will occur . • Move the dishwasher close to the installation location and lay it on its back. ? ...

  • GE 206C1559P197 - page 7

    STEP 6: INST ALL 90° ELBOW • Wrap a 90° elbow with thread seal tape. • Thread 90° elbow onto the water valv e. • Do not overtighten elbow . Water valve bracket could bend or water valv e fitting could break. • Position the end of the elbow to face the rear of the dishwasher . Figure K Figure J Tip: Avoid unnecessary service charges. Make ...

  • GE 206C1559P197 - page 8

    Power Cord (If Used) Insulation Blanket Water Line Maximum Drain Hose Length 10' House Wiring Drain Hose Figure N STEP 9: INST ALL DRAIN HOSE, THROUGH CABINE T • Position dishwasher in fr ont of cabinet opening. Insert drain hose into the hole in cabinet side. If a power cord is used, guide the end through a separate hole. STEP 8: P OSITION ...

  • GE 206C1559P197 - page 9

    STEP 13: PUSH DISHW ASHER INTO FINAL P OSITION • Check the tub insulation blanket , if equipped, to be sure it is smoothly wrapped around the tub. It should not be “bunched up” and it must not interfere with the door springs. If the insulation is “bunched up” or interfering with the springs, straighten and recenter the blanket prior to sl ...

  • GE 206C1559P197 - page 10

    Dishwasher Installation Figure R STEP 14: LEVEL DISHW ASHER IMP ORT ANT – Dishwasher must be level for pr oper dish rack operation, wash performance and door operation. The dishwasher must be leveled left to right and fr ont to back. This ensures the dish racks will not r oll in or out on their own, circulation water will fl ow to the pump inlet ...

  • GE 206C1559P197 - page 11

    • Connect drain line to air gap, waste tee or disposer using the previously determined method. Secur e hose with a screw-type clamp. Waste Tee Installation Method 1 – Air gap with waste tee or disposer Disposer Installation Waste Tee Installation Method 2 – “High drain loop ” with waste tee or disposer With this method you will need the d ...

  • GE 206C1559P197 - page 12

    Dishwasher Installation Figure AA STEP 18: CONNECT POWER SUPPL Y If a power cord with plug is alr eady installed proceed to Step 19. STEP 19: PRE TEST CHECKLIST Review this list after installing your dishwasher to avoid charges for a service call that is not covered by your warranty. ■ ■ Check to be sure power is OFF . ■ ■ Open door and rem ...

  • GE 206C1559P197 - page 13

    Dishwasher Installation STEP 20: DISHW ASHER WE T TEST ■ ■ Turn on power supply or plug pow er cord into outlet , if equipped. ■ ■ Latch door . ■ ■ Push Rinse Only pad. ■ ■ Push Start/Reset pad one time. Dishwasher should start . ■ ■ Check to be sure that water enters the dishw asher . If water does not enter the dishwasher , ch ...

  • GE 206C1559P197 - page 14

    Notes 14 ...

  • GE 206C1559P197 - page 15

    Notes 13 ...

  • GE 206C1559P197 - page 16

    GE Consumer & Industrial General Electric Company Louisville, Kentucky 40225 GE Appliances.com © 2009 General Electric Company SPECIFICA TIONS SUBJECT TO CHANGE WITHOUT NO TICE ...

  • GE 206C1559P197 - page 17

    Appareils ménagers GE Consumer and Industrial Dir ectives d’installation Lave-v aisselle encastré Pour toute question, composez le 1.800.561.3344 ou visit ez notre site Web : www .electromenagersge.ca IMP ORT ANT – Le lave-vaisselle DOIT êtr e installé de manière à ce qu’il puisse êtr e sorti de son emplacement si des réparations sont ...

  • GE 206C1559P197 - page 18

    OUTILS NÉCESSAIRES : ■ ■ Tournevis Phillips ■ ■ T ourne-écrous de 6,3 mm (1/4 po) et de 7,9 mm (5/16 po) ■ ■ Clé à molette de 15,2 cm (6 po) ■ ■ Niveau ■ ■ Équerre de charpentier ■ ■ Ruban à mesurer ■ ■ Lunettes de sécurité ■ ■ Lampe de poche ■ ■ Seau pour r ecueillir l’eau lors du rinçage de la condui ...

  • GE 206C1559P197 - page 19

    Méthode n° 1 – Coupure anti-refoulement av ec raccord en T ou broyeur à déchets Il faut installer une coupure anti-refoulement lorsqu’elle est exigée par les ordonnances et les codes locaux en vigueur . Cette coupure anti- refoulement doit être installée conformément aux dir ectives données par le fabricant . PRÉP ARA TION DE L’OUVE ...

  • GE 206C1559P197 - page 20

    Dans le cas des modèles dotés d’un cordon d’alimentation : Ne modifiez pas la fiche fournie avec l’ appareil; si vous ne pouvez pas la brancher dans la prise de courant , faites installer une prise de courant appropriée par un technicien qualifié. Préparation des armoir es et cheminement des fils • Les fils peuvent entrer dans l’ouve ...

  • GE 206C1559P197 - page 21

    PRÉP ARA TION DE L’ ALIMENT A TION EN E AU CHA UDE • La conduite peut entrer du côté gauche, du côté dr oit , de l’arrièr e ou du plancher dans la partie ombrée indiquée dans la Figure F . • La conduite peut passer par le même trou que le câble électrique et le boyau de vidange, ou vous pouvez percer un trou supplémentair e de 3 ...

  • GE 206C1559P197 - page 22

    Installation du lave-vaisselle Figure G • Remettez en place les pieds de nivellement sur le lave- vaisselle, à 3,1 cm (1/8 po) environ du cadr e, comme indiqué dans l’illustration. Approx. 1/8" É T APE 3 : ENLÈVEMENT DE L A BASE DE BOIS, INST ALL A TION DES PIEDS DE NIVELLEMENT IMP ORT ANT – Ne frappez pas sur la base de bois pour l? ...

  • GE 206C1559P197 - page 23

    É T APE 6 : INST ALLA TION DU COUDE DE 90° • Appliquez du ruban pour joints filetés sur les filets du coude de 90°. • Vissez le coude de 90° dans l’électrovanne. • Ne serrez pas le coude de façon excessive; le support de l’électrovanne pourrait se déformer ou le raccord de l’électr ovanne pourrait se casser . • T ournez l’ ...

  • GE 206C1559P197 - page 24

    Figure N ÉT APE 9 : INSERTION DU BOY A U DE VIDANGE DANS L ’ORIFICE DE L’ ARMOIRE • Placez le lave-vaisselle vis-à-vis de l’ouverture dans les armoir es. Insérez le boyau de vidange dans l’orifice que vous avez précédemment per cé dans la paroi des armoires. Si l’ appareil est doté d’un cordon d’ alimentation, faites passer l ...

  • GE 206C1559P197 - page 25

    Figure Q Installation du lave-vaisselle É T APE 12 : INST ALLA TION DES SUPP ORTS DE MONT A GE L A TÉRA UX GPF65 Sautez cette étape si le dessous du compt oir est en bois ou fabriqué à l’aide d’un matériau similaire. Au cours de cette étape, vous aurez besoin de l’ensemble de supports de montage latéraux mis de côté à l’étape 1. ...

  • GE 206C1559P197 - page 26

    Installation du lave-vaisselle Figure R É T APE 14 : MISE DE NIVEAU DU L A VE-V AISSELLE IMP ORT ANT – Le lave-vaisselle doit êtr e de niveau pour assurer le bon fonctionnement des paniers et de la porte du lave-vaisselle et obtenir une bonne effi cacité de lavage. Le lave-vaisselle doit êtr e mis de niveau de gauche à droite, et de l’av ...

  • GE 206C1559P197 - page 27

    • Branchez le boyau de vidange à la coupure anti- refoulement , au raccord en T ou au broyeur à déchets à l’aide de la méthode choisie pr écédemment . Fixez solidement le boyau à l’aide d’un collier à vis sans fin. Méthode n° 1 – Coupure anti-refoulement av ec raccord en T ou broyeur à déchets Installation avec raccord en T M ...

  • GE 206C1559P197 - page 28

    Installation du lave-vaisselle Figure AA É T APE 18 : BRANCHEMENT DE L’ ALIMENT A TION ÉLECTRIQUE Si un cordon d’ alimentation pourvu d’une fiche est déjà installé sur l’appar eil, passez à l’étape 19. É T APE 19 : LISTE DE C ONTRÔLE PRÉLIMINAIRE Passez en revue cette liste après l’installation de votr e lave-vaisselle pour ? ...

  • GE 206C1559P197 - page 29

    Installation du lave-vaisselle É T APE 20 : ESSAI DU LA VE-V AISSELLE A VEC DE L’E AU ■ ■ Rétablissez l’ alimentation électrique ou si l’appar eil est doté d’un cordon d’ alimentation, branchez-le dans la prise de courant murale. ■ ■ Verr ouillez la porte du lave-vaisselle. ■ ■ Appuyez sur la touche Rinse Only (Rinçage). ...

  • GE 206C1559P197 - page 30

    Notes 14 ...

  • GE 206C1559P197 - page 31

    Notes 15 ...

  • GE 206C1559P197 - page 32

    GE Consumer & Industrial General Electric Company Louisville, Kentucky 40225 www .electromenagersge.ca © 2009 General Electric Company LES SPÉCIFICA TIONS PEUVENT ÊTRE MODIFIÉES S ANS PRÉ AVIS ...

Manufacturer GE Category Dishwasher

Documents that we receive from a manufacturer of a GE 206C1559P197 can be divided into several groups. They are, among others:
- GE technical drawings
- 206C1559P197 manuals
- GE product data sheets
- information booklets
- or energy labels GE 206C1559P197
All of them are important, but the most important information from the point of view of use of the device are in the user manual GE 206C1559P197.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals GE 206C1559P197, service manual, brief instructions and user manuals GE 206C1559P197. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product GE 206C1559P197.

Similar manuals

A complete manual for the device GE 206C1559P197, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use GE 206C1559P197 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of GE 206C1559P197.

A complete GE manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual GE 206C1559P197 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the GE 206C1559P197, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the GE 206C1559P197, that we can find in the current document
3. Tips how to use the basic functions of the device GE 206C1559P197 - which should help us in our first steps of using GE 206C1559P197
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with GE 206C1559P197
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of GE 206C1559P197 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning GE 206C1559P197?

Use the form below

If you did not solve your problem by using a manual GE 206C1559P197, ask a question using the form below. If a user had a similar problem with GE 206C1559P197 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)