English dropdown-ico

Manual Honeywell PRO TH4110D

16 pages 0.66 mb
Download

Go to site of 16

Summary
  • Honeywell PRO TH4110D - page 1

    Installation Guide TH4110D Programmable Thermostat ...

  • Honeywell PRO TH4110D - page 2

    Product Application This thermostat provides electronic control of 24 V A C single-stage heating and cool- ing systems, or 750 mV heating systems. System T ypes • Gas, oil, or electric heat with air conditioning • W arm air , hot water , high-efficiency furnaces, heat pumps, steam, gravi- ty • Heat only • Heat only with f an • Cool only ? ...

  • Honeywell PRO TH4110D - page 3

    PRO TH4110D Programmable Thermostat 1 Install the thermostat about 5 feet (1.5m) above the floor in an area with good air circulation at average temperatur e. Do not install in locations where the thermostat can be af fected by: • Drafts or dead spots behind doors and in corners • Hot or cold air from ducts • Sunlight or radiant heat from app ...

  • Honeywell PRO TH4110D - page 4

    Installation Guide 2 Pre-installation checklist Package contents Check to make sure y our package includes the f ollowing items: • PR O TH4110D digital thermostat (wallplate attached to back) • Operating manual • W all anchors and mounting screws (2 eac h) • AA alkaline batteries (2) • Quick ref erence card Required tools & supplies ? ...

  • Honeywell PRO TH4110D - page 5

    PRO TH4110D Programmable Thermostat 3 W allplate installation Remove the w allplate from the ther- mostat as shown at left, then f ollow directions below f or mounting. 1 Pull wires through wire hole. 2 P osition wallplate on wall, level and mark hole positions with pencil. 3 Drill holes at marked positions as shown below , then tap in supplied wal ...

  • Honeywell PRO TH4110D - page 6

    Installation Guide 4 Wiring 1 Loosen screw terminals, insert wires into terminal block, then re- tighten screws. 2 Push e xcess wire back into the wall opening. K eep wires in shaded area as shown at left. 3 Plug the wall opening with non- f lamma ble insulation to pr event drafts from affecting thermostat operation. T erminal Designations W W Heat ...

  • Honeywell PRO TH4110D - page 7

    PRO TH4110D Programmable Thermostat 5 T ypical 1H/1C system: 1 transformer T ypical 1H/1C system: 2 transformers 1 Power supply . Provide disconnect means and overload pr otection as required. 2 Factory-installed jumper . Remove for 2-transformer systems only . 3 Use either O or B terminals for changeover valve. 4 Use a small piece of wire (not sup ...

  • Honeywell PRO TH4110D - page 8

    Installation Guide 6 • G G a a s s o o r r O O i i l l : : For gas or oil heating systems, leave the f an operation switc h in this factor y-set position (This setting is for systems that control the fan in a call f or heat.) • E E l l e e c c t t r r i i c c o o r r H H e e a a t t P P u u m m p p : : Change the switc h to this setting for hea ...

  • Honeywell PRO TH4110D - page 9

    PRO TH4110D Programmable Thermostat 7 AC Power The thermostat can be powered by 24 V A C power , or by batter ies. T o wire the thermostat for A C power , connect the common side of the cooling transf or mer to the “C” terminal as shown at left. I I m m p p o o r r t t a a n n t t : : Remove R/Rc jumper f or 2-transf or mer systems onl y . (See ...

  • Honeywell PRO TH4110D - page 10

    1 0 Installation Guide 8 1 5 9 13 14 15 System type Heating cycle rate (CPH: cycles/hour) Compressor cycle rate (CPH) Adaptive Intelligent Recovery T emperature display Compressor protection 0 Gas, oil or electric heat with air conditioning 1 Heat pump (5 minute compressor of f time in heating and cooling) 5 For gas or oil furnaces of less than 90% ...

  • Honeywell PRO TH4110D - page 11

    PRO TH4110D Programmable Thermostat 9 10 0 T est 10 30 70 Heating system Cooling system Thermostat information (for refer ence only) 0 Heat and fan turn off. 1 Heat turns on. Fan also turns on immediately if Fan Operation Switch is set to Electric Heat/Heat Pump (see page 6). 0 Compressor and fan turn off. 1 Compressor and fan turn on. 71 Software ...

  • Honeywell PRO TH4110D - page 12

    Installation Guide 10 Built-in compressor pr otection (Setup Function 15) This featur e helps prevent damag e to the compressor in the air conditioning or heat pump system. Damage can occur if the compressor is r e- started too soon after shutdown. This feature for ces the compressor to wait f or a few minutes befor e restarting. During the wait ti ...

  • Honeywell PRO TH4110D - page 13

    PRO TH4110D Programmable Thermostat 11 Quick refer ence to controls • Set: Press to set time/day/ schedule • Hold: Press to override programmed temperatur e control. • Run: Press to r esume program schedule System switch • Cool: Thermostat controls only the cooling system. • Heat: Thermostat controls only the heating system. • Off: Heat ...

  • Honeywell PRO TH4110D - page 14

    Installation Guide 12 In case of difficulty If you hav e dif ficulty with your thermostat, please tr y the sugg estions below . Most problems can be corrected quickl y and easily . Display is blank • Check circuit br eaker and reset if necessary . • Make sure heating & cooling power switches ar e on. • Make sure equipment door is secur el ...

  • Honeywell PRO TH4110D - page 15

    PRO TH4110D Programmable Thermostat 13 Accessories Please contact your distributor to order accessories. Cover plate assembly ............................................Part Number 50002883-001 (Used to cover marks left by old thermostats.) Specifications T emperature Ranges • Heat: 40° to 90°F (4.5° to 32°C) • Cool: 50° to 99°F (10° to ...

  • Honeywell PRO TH4110D - page 16

    Honeywell International Inc. 1985 Douglas Drive North Golden V alley , MN 55422 http://yourhome.honeywell.com Automation and Control Solutions Printed in U.S.A. on recycled paper containing at least 10% post-consumer paper fibers. ® U.S. Registered T rademark. © 2005 Honeywell International Inc. Patents pending. All rights reserved. 69-1849 • 0 ...

Manufacturer Honeywell Category Thermostat

Documents that we receive from a manufacturer of a Honeywell PRO TH4110D can be divided into several groups. They are, among others:
- Honeywell technical drawings
- PRO TH4110D manuals
- Honeywell product data sheets
- information booklets
- or energy labels Honeywell PRO TH4110D
All of them are important, but the most important information from the point of view of use of the device are in the user manual Honeywell PRO TH4110D.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Honeywell PRO TH4110D, service manual, brief instructions and user manuals Honeywell PRO TH4110D. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Honeywell PRO TH4110D.

Similar manuals

A complete manual for the device Honeywell PRO TH4110D, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Honeywell PRO TH4110D by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Honeywell PRO TH4110D.

A complete Honeywell manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Honeywell PRO TH4110D - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Honeywell PRO TH4110D, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Honeywell PRO TH4110D, that we can find in the current document
3. Tips how to use the basic functions of the device Honeywell PRO TH4110D - which should help us in our first steps of using Honeywell PRO TH4110D
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Honeywell PRO TH4110D
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Honeywell PRO TH4110D in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Honeywell PRO TH4110D?

Use the form below

If you did not solve your problem by using a manual Honeywell PRO TH4110D, ask a question using the form below. If a user had a similar problem with Honeywell PRO TH4110D it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)