English dropdown-ico

Manual Windsor CLP12IE

23 pages 0.69 mb
Download

Go to site of 23

Summary
  • Windsor CLP12IE - page 1

    Read these instructions before operating the machine Bitte lesen Sie diese Anleitungen, bevor Sie die Maschine in Gebrauch nehmen Operating Instructions (GB/USA) Bedienungsanleitung (GER) 86038280 04/04/07 PRV NO. 98656 AC CARPET EXTRACTOR MOD EL: C O U N T R Y CLP12IA - 10080090 AUSTRALIA CLP12IB - 10080100 BRITIAN CLP12IE - 10080110 EUROPE CLP12I ...

  • Windsor CLP12IE - page 2

    MACHINE DATA LOG 86038280 04/04/07 2ENG YOUR DEALER Name: ____________________ __________________________ __________________________ __________________________ Address: __________________ __________________________ ___________________________________ ________________ Phone Number: _________ _________________________ ______________________________ _ ...

  • Windsor CLP12IE - page 3

    TABLE OF CONTENTS 86038280 04/04/07 3EN G Machine Da ta Log. ............................................... 2 Table of Co ntents ................................................. 3 HOW TO USE THIS MANUAL How to use this Manual. ....................................... 1-1 SAFETY Important Safety Instructions ............................... 2-1 Haza ...

  • Windsor CLP12IE - page 4

    HOW TO USE THIS MANUAL 86038280 04/04/07 1-1ENG This manual contains the f ollowin g sections: - HOW TO USE THIS MANUAL - SAFETY - OPERATIONS - MAINTENANCE - PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts. Parts may be ordered from authori zed Windsor dealers. When pla ...

  • Windsor CLP12IE - page 5

    86038280 04/04/07 2-1EN G IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. This machine is for commercial use. To reduce the risk of fire, electric shock, or injury: Connect to a properly grounded outlet . Do not leav ...

  • Windsor CLP12IE - page 6

    HAZARD INTENSITY LEVEL 86038280 04/04/07 2-2ENG The following symbols are use d throu ghout this guide as indicated i n their de scriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensit y identified by signal words - WARNING and CAUTION and FOR SAFETY. The level of hazard intensity is determined by the following definitions: WAR ...

  • Windsor CLP12IE - page 7

    GROUNDING INSTRUCTIONS 86038280 04/04/07 2-3EN G THIS PRODUCT IS FOR COMM E RCIAL USE ONLY. ELECTRICAL: The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages a bove or below those indicated on the data label will cause serious dama ge to the motors. EXTENSION CORDS: If an extension cord is used, the wire siz ...

  • Windsor CLP12IE - page 8

    TECHNICAL SPECIFICATIONS 86038280 04/04/07 3-1EN G ITEM DIMENSION/CAPACITY Electrical 230-240V, 7A, 50 HZ Electric Vacuum Motor (1) 3 stage, 1 hp, 99 cfm (2.80 cubic m/ min.) Waterlift 117” (297cm) Brush (1) 18” (45.7cm.) Brush Speed 1000 rpm Solution Pump 100 PSI, diaphragm style, internal bypass Solution Capacity 12 gallons (45.5l) Solution S ...

  • Windsor CLP12IE - page 9

    CONTROLS/COMPONENT LOCATIONS 86038280 04/04/07 3-2EN G 1. Main Handle. Used to pull and maneuver machine. 2. Handle Adjustment. Used to adjust height of handle, and allow machine to be use d in “PUSH” or “PULL orientation. 3. Electrical Cord. 4. Solution Switch. Turns on pump. Continuou s position (bottom) activates electro-valve to dispense ...

  • Windsor CLP12IE - page 10

    CONTROLS/COMPONENT LOCATIONS 86038280 04/04/07 3-3EN G 1 2 3 13 12 6 9 8 1. Solution Accessory Tool Hookup. Used for various auxiliary cleaning t ools. 2. Vacuum Hose Door. Used to connect various auxiliary 1 ½ inch cleaning tool vacuum hoses. 3. Brush Height Adjustment. Used to regulate brush height from storage position to various carpet heights ...

  • Windsor CLP12IE - page 11

    CONTROLS/COMPONENT LOCATIONS 86038280 04/04/07 3-4EN G 1. Solution Intake Cover. 2. Vacuum Intake Cover. 3. Float Shut-Off. 4. Clean-Out Opening. 5. Pour Spout. 6. Lift Handle. 2 1 3 4 5 6 6 ...

  • Windsor CLP12IE - page 12

    OPERATIONS 86038280 04/04/07 3-5ENG Remove electrical co rd an d literature from recovery tank. Fill solution tank (see filling instructions ). Adjust brush to proper setting. Note: For good operation the brush must skim the carpet. If circuit breaker trips raise brush to p revent damage to m otor or ca rpet. Plug cord into grounded ou t let. Note: ...

  • Windsor CLP12IE - page 13

    OPERATIONS 86038280 04/04/07 3-6EN G Select contin uou s setting to st art solution spray or select intermittent setting to enable use of trigger switches to sta rt solution spra y. The intermittent setting requires the operator to hold any one of the three trigger switches in the “on” positio n with the fingers, and is typically used in small ...

  • Windsor CLP12IE - page 14

    FILLING OPERATIONS 86038280 04/04/07 3-7EN G FILLING THE CLIPPER NOTE: Use clean bucket of water to fill solution tank Do not put defoamer, solvents, spotter or prespray chemicals in the solution tank . Do not allow water to spill into vacuum motor inlet. Dry spillage from top of solution tank before replacing recovery tank . CHEMICALS Suitable Che ...

  • Windsor CLP12IE - page 15

    CLEANING PROCEDURE 86038280 04/04/07 3-8EN G Release intermittent trigger switches or turn off continuous setting on solution switch approximately 1 foot before en ding cleaning pass. Push down on handle to raise vacuum shoe and brush before moving to the next cleaning pass. Overlap brush contact area a minimum of 1inch on the right (close cleaning ...

  • Windsor CLP12IE - page 16

    CLEANING PROCEDURE 86038280 04/04/07 3-9EN G STEP 5 STEP 6 After cleaning, turn off all controls, return brush to storage position and ca refully unplug machine. STEP 4 STEP 1 Use right side of machine for cle anin g against walls. SOLUTION INTAKE COVER VACUUM INTAKE COVER O R Start at wall closest to power outlet. For large areas flip handle and o ...

  • Windsor CLP12IE - page 17

    CLEANING PROCEDURE 86038280 04/04/07 3-10EN G To speed drying, use a Windblo wer ™ fan. Empty recovery tank by releasing dump hose. Use a hose with cold water to clean out the recovery tank. Also drain solution tank after each use. STEP 7 STEP 8 RECOVERY DRAIN SOLUTION DRAIN ...

  • Windsor CLP12IE - page 18

    ACCESSORY TOOL USAGE 86038280 04/04/07 3-11ENG Turn on vacuum motor swit ch and set solution switch to intermittent position. Note: Be sure brush switch is in off position and brush is in storage position. Squeeze handle on accessory tool to begin cleaning. STEP 3 STEP 4 STEP 1 STEP 2 Use only one of the following acceptable accessory tools. 860000 ...

  • Windsor CLP12IE - page 19

    MAINTENANCE 86038280 04/04/07 4-1ENG ONLY QUALIFIED MAINTENANCE PE RSONNEL ARE TO PERFORM THE FOLLOWING REPAIRS. VACUUM MOTOR REPLACEME NT 1. Turn off all switches and unplug machi ne. 2. Remove recovery tank. 3. Remove the (2) screws that fasten the solution tank to the frame, and tilt tank back to expose the inside of the frame. 4. Locate the vac ...

  • Windsor CLP12IE - page 20

    MAINTENANCE 86038280 04/04/07 4-2ENG SOLUTION PUMP REPLACEMENT 1. Turn off all switches and unplug the machin e. 2. Remove recovery tank. 3. Remove the (2) screws that fasten the solution tank to the frame, and tilt tank back to expose the inside of the frame. 4. Remove solution hoses from fittings in pump. 5. Remove the (2) screws that fasten the ...

  • Windsor CLP12IE - page 21

    MAINTENANCE 86038280 04/04/07 4-3EN G PERIODIC MAIN TENANCE Twice a month, flush a white vinegar sol ution (One quart vinegar to two gallons of water) or anti- browning solution (mixed as directe d) t hrough the extractor. This will prev ent build-up of alkaline residue in the system. If spray jets become clog ged, remove the spray tips, wash them ...

  • Windsor CLP12IE - page 22

    TROUBLESHOOTING CHART 86038280 04/04/07 4-4ENG PROBLEM CAUSE SOLUTION No Power, Nothing Runs 1. Is the cord plugged in? 2. Circuit breaker tripped in building. 3. Faulty switch. 4. Faulty power cord or pigtail. 1. Plug in cord. 2. Reset breake r 3. Call for service. 4. Call for service. Vacuum Motor Will Not Run 1. Vacuum circuit breaker tripped. 2 ...

  • Windsor CLP12IE - page 23

    NOTES 86038280 04/04/07 4-5EN G ...

Manufacturer Windsor Category Carpet Cleaner

Documents that we receive from a manufacturer of a Windsor CLP12IE can be divided into several groups. They are, among others:
- Windsor technical drawings
- CLP12IE manuals
- Windsor product data sheets
- information booklets
- or energy labels Windsor CLP12IE
All of them are important, but the most important information from the point of view of use of the device are in the user manual Windsor CLP12IE.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Windsor CLP12IE, service manual, brief instructions and user manuals Windsor CLP12IE. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Windsor CLP12IE.

Similar manuals

A complete manual for the device Windsor CLP12IE, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Windsor CLP12IE by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Windsor CLP12IE.

A complete Windsor manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Windsor CLP12IE - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Windsor CLP12IE, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Windsor CLP12IE, that we can find in the current document
3. Tips how to use the basic functions of the device Windsor CLP12IE - which should help us in our first steps of using Windsor CLP12IE
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Windsor CLP12IE
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Windsor CLP12IE in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Windsor CLP12IE?

Use the form below

If you did not solve your problem by using a manual Windsor CLP12IE, ask a question using the form below. If a user had a similar problem with Windsor CLP12IE it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)