-
Directed Audio 600/4 - page 1
model 600/4 ...
-
Directed Audio 600/4 - page 2
2 © 2003 Directed Electronics, Inc ...
-
Directed Audio 600/4 - page 3
3 T ABLE OF CONTENTS CONGRA TULA TIONS Congratulations for choosing a Directed Audio power amplifier from Directed Electronics, the industry leader in high quality automotive security and audio equipment since 1990. Directed Audio power amplifiers continue to set new standards of perfor- mance, reliability , and affordability in the mobile electron ...
-
Directed Audio 600/4 - page 4
LIMITED TWO-YEAR CONSUMER W ARRANTY 4 © 2003 Directed Electronics, Inc Directed Electronics, Inc. promises to the original purchaser , to replace this product should it prove to be defective in workman- ship or material under normal use, for a period of two years from the date of purchase by the dealer as indicated by the date code marking of the ...
-
Directed Audio 600/4 - page 5
5 © 2003 Directed Electronics, Inc High-powered car audio systems may produce sound pressure levels that exceed the threshold at which hearing loss may result. They may also impair a driver’ s ability to hear traffic sounds or emergency vehi- cles. Use common sense and practice safe listening habits when listening to or adjusting your audio syst ...
-
Directed Audio 600/4 - page 6
6 © 2003 Directed Electronics, Inc INST ALLA TION GUIDELINES 1. Please read this owner’ s manual carefully before installing this ampli- fier . 2. Disconnect the batter y ground terminal prior to making any elec- trical connections. 3. Check for any hazards or obstruc- tions such as gas tanks, fuel or brake lines, and wiring harnesses before mou ...
-
Directed Audio 600/4 - page 7
7 © 2003 Directed Electronics, Inc speaker load, the more heat is generated. For low impedance speaker applications or restricted ventilation installations, an external cooling fan may be advisable. 9. Batter y and ground connections to the vehicle should be made with crimped ring terminals of the appro- priate size (surface area is what counts); ...
-
Directed Audio 600/4 - page 8
8 © 2003 Directed Electronics, Inc 1. S S p p e e a a k k e e r r O O u u t t T T e e r r m m i i n n a a l l s s - Connect the speakers to these terminals. (Refer to the Speaker Connection section of this guide.) 2. P P o o w w e e r r F F u u s s e e s s - - These fuse(s) protect the amplifier against internal elec- trical damage and are meant t ...
-
Directed Audio 600/4 - page 9
9 © 2003 Directed Electronics, Inc FIGURE 2—AMPLIFIER CONNECTIONS 600/4 REAR REM GND BAT T 25A x 2 FUSE FRONT REAR LR BRIDGED SPEAKER OUTPUT 4. R R e e m m o o t t e e T T u u r r n n O O n n - This terminal turns on the amplifier when (+) 12 volt is applied to it. Connect it to the remote turn on lead of the head unit or signal source. If a (+) ...
-
Directed Audio 600/4 - page 10
10 © 2003 Directed Electronics, Inc TOP P ANEL CONTROLS GAIN GAIN FREQ FREQ MIN 50Hz MAX 500Hz MIN 50Hz MAX 500Hz LPF LPF HPF HPF FLAT FLAT FLAT BASS EQ BASS EQ OFF OFF ON ON REAR FRONT FIGURE 3—AMPLIFIER CONTROLS 600/4 TOP 4 1. I I n n p p u u t t G G a a i i n n A A d d j j u u s s t t m m e e n n t t - Controls amplifier sensitivity and is us ...
-
Directed Audio 600/4 - page 11
SPEAKER WIRING DIAGRAMS 11 © 2003 Directed Electronics, Inc Simultaneous stereo/mono operation (top view) N N O O T T E E : : For bridged two channel operation as shown in this diagram, connect right channel RCA cables to the front inputs of the amplifier , and left channel RCA cables to the rear inputs of the amplifier . For summed subwoofer appl ...
-
Directed Audio 600/4 - page 12
12 © 2003 Directed Electronics, Inc CROSSOVER SETTINGS AND GAIN ADJUSTMENT Y our Directed Audio power amplifier needs to be adjusted carefully to achieve maximum performance. These are some guidelines to follow when fine-tuning the amplifier . For full-range and simultaneous stereo/mono bass applications, the crossover selection switch should ...
-
Directed Audio 600/4 - page 13
SPECIFICA TIONS 13 © 2003 Directed Electronics, Inc RMS continuous power per channel, All channels driven into 4 ohms from 20 to 20,000 Hz, with less than 0.08% T otal Harmonic Distor tion @ 14.4 VDC C RMS continuous power per channel , All channels driven into 2 ohms from 20 to 20,000 Hz, with less than 0.1% T otal Harmonic Distor tion @ 14.4 VDC ...
-
Directed Audio 600/4 - page 14
16 © 2003 Directed Electronics, Inc The company behind this system is Directed Electronics, Inc. Since its inception, Directed has had one purpose, to provide customers with the finest vehicle security , car stereo products, rear seat entertainment, and accessories available. The recipient of more than 20 patents in the field of advanced electroni ...
Do you have a question concerning Directed Audio 600/4?
Use the form below
If you did not solve your problem by using a manual Directed Audio 600/4, ask a question using the form below. If a user had a similar problem with Directed Audio 600/4 it is likely that he will want to share the way to solve it.