-
Harbor Freight Tools 45813 - page 1
10” RANDOM ORBIT POLISHER/W AXER Model 45813 ASSEMBL Y AND OPERA TING INSTR UCTIONS 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb site at: http://www.harborfreight.com Cop yright 2003 by Harbor F reight T ools ® . All rights reser v ed. No por tion of this manual or any ar twork contained herein may be reproduced in an y shape or ...
-
Harbor Freight Tools 45813 - page 2
PR ODUCT SPECIFICA TIONS SA VE THIS MANU AL Y ou will need this man ual f or the safety warnings and precautions, assembly , operating, inspection, maintenance and cleaning procedures, parts list and as- sembl y diagram. Keep y our in voice with this man ual. Write the in voice n umber on the inside of the front co ver . K eep this manual and in v ...
-
Harbor Freight Tools 45813 - page 3
3. Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed. ELECTRICAL SAFETY 4. Grounded tools must be plugged into an outlet properly installed and grounded in accordance with a ...
-
Harbor Freight Tools 45813 - page 4
11. Dress properl y . Do not wear loose clothing or je welry . Contain long hair . K eep your hair , clothing, and gloves a wa y fr om mo ving par ts. Loose clothes, je welry , or long hair can be caught in mo ving par ts. 12. A v oid accidental star ting. Be sure the P ower Switch is off before plug ging in. Carrying power tools with your finger o ...
-
Harbor Freight Tools 45813 - page 5
22. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that ma y affect the tool’ s operation. If dama ged, have the tool serviced before using. Many accidents are caused by poorly main- tained tools. 23. Use only accessories that are recommended by the manufacturer for your model. Accessories that may b ...
-
Harbor Freight Tools 45813 - page 6
7. A v oid unintensional starting. Mak e sure you are prepared to begin work bef ore tur ning on the P olisher/W ax er . 8. Do not for ce the Polisher/W axer . This tool will do the work better and safer at the speed and capacity for which it was designed. Do not force the rotating Pad (par t #26) into the vehicle being w axed/polished. Apply moder ...
-
Harbor Freight Tools 45813 - page 7
GROUNDING W ARNING! Improperly connecting the grounding wire can result in the risk of electric shock. Check with a qualfified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord ...
-
Harbor Freight Tools 45813 - page 8
FIGURE B SKU 45813 P A GE 8 DOUBLE INSULA TED T OOLS: T OOLS WITH TW O PR ONG PLUGS 4. T ools mar ked “Double Insulated” do not require grounding. The y ha v e a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and ...
-
Harbor Freight Tools 45813 - page 9
6. If you are using an extension cord outdoors, make sure it is marked with the suffix “W -A” (“W” in Canada) to indicate it is acceptable f or outdoor use. 7. Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using ...
-
Harbor Freight Tools 45813 - page 10
UNP A CKING When unpacking, check to make sure all the parts shown on the Parts List on page 14 are included. If any par ts are missing or broken, please call Harbor F reight T ools at the number shown on the cover of this manual as soon as possible. ASSEMBL Y AND OPERA TING INSTRUCTIONS NO TE: For additional inf or mation regarding the par ts list ...
-
Harbor Freight Tools 45813 - page 11
SKU 45813 P A GE 11 10. After the wax has been applied to the v ehicle’s surf ace, turn the P ow er Switch (par t #13) to its “OFF” position. Then unplug the P o wer Cord (par t #14) from the electrical extension cord, and unplug the extension cord from the grounded, 120 volt, electrical outlet. (See Figure D.) TERR Y CLO TH W AXING BONNET (# ...
-
Harbor Freight Tools 45813 - page 12
SKU 45813 P A GE 12 17. Grip the P olisher/W ax er fir mly with both hands. Then tur n the P ower Switch (part #13) to its “ON” position and allow the Pad (part #26) to rotate to its fullest speed. (See Figure D.) 18. Begin polishing the vehicle b y lightly buffing off the wax residue in a circular pattern. Continue polishing until all the wax ...
-
Harbor Freight Tools 45813 - page 13
6. The W axing/P olishing Bonnets (par ts #28, #29) ma y be machine-washed, in cold w ater , with detergent. Then, machine-dry the Bonnets at medium heat. 7. Use only a clean cloth and mild detergent to clean the body of the W axer/P olisher . Do not use solvents . Do not immerse any par t of the tool in liquid. PLEASE READ THE FOLLO WING CAREFULL ...
-
Harbor Freight Tools 45813 - page 14
SKU 45813 P A GE 14 ASSEMBL Y DIA GRAM NO TE: Some par ts are listed and shown f or illustration pur poses only , and are not available individually as replacement parts. 28: W AXING BONNET NOT SHO WN 29: POLISHING BONNET NOT SHOWN P ARTS LIST 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 Part # Description Qt y . Part # D ...
Do you have a question concerning Harbor Freight Tools 45813?
Use the form below
If you did not solve your problem by using a manual Harbor Freight Tools 45813, ask a question using the form below. If a user had a similar problem with Harbor Freight Tools 45813 it is likely that he will want to share the way to solve it.