English dropdown-ico

Manual Citizen Systems CT-S2000

32 pages 0.47 mb
Download

Go to site of 32

Summary
  • Citizen Systems CT-S2000 - page 1

    LINE THERMAL PRINTER MODEL CT -S2000/CT -S2000DC User’ s Manual ...

  • Citizen Systems CT-S2000 - page 2

    WEEE MARK ,I RX ZDQWWR GLVSRVH W KLV SURGXFW GRQRW PL[ ZLWK JHQHUDO KRXVHKROG ZDVWH 7KHUH LV D VHSDUDWHFROOHFWLRQVVWHPV IRUXVHGHOHFWURQLFV SURGXFWVLQDF FRUGDQFH ZLWKOHJLVODWLRQXQGHU WKH:((('LUHFWLYH'LUHFWLYH(& ...

  • Citizen Systems CT-S2000 - page 3

    IMPORT ANT : This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are de ...

  • Citizen Systems CT-S2000 - page 4

    — 1 — GENERAL PRECAUTIONS ● Before using this product, be sure to read through this manual. After having read this manual, keep it in a safe, readily accessible place for future reference. ● The information contained herein is subject to change without prior notice. ● Reproduction or transfer of part or all of this document in any means i ...

  • Citizen Systems CT-S2000 - page 5

    — 2 — SAFET Y PRECA UTIONS ... WHICH SHOULD BE STRICTL Y OBSER VED Before using this product for the first time, carefully read these SAFETY PRECAUTIONS. Improper handling may result in accidents (fire, electric shock or injury). In order to prevent injury to operators, third parties, or damage to property , special warning symbols are used in ...

  • Citizen Systems CT-S2000 - page 6

    — 3 — ■ Do not use or store this product in a place where it will be exposed to: * Flames or moist air . * Direct sunlight. * Hot airflow or radiation from a heating device. * Salty air or corrosive gases. * Ill-ventilated atmosphere. * Chemical reactions in a laboratory . * Airborne oil, steel particles, or dust. * Static electricity or stro ...

  • Citizen Systems CT-S2000 - page 7

    — 4 — Do not use the printer under the following conditions. ■ A state subject to vibration or unstable state. ■ A state with this product slanted. • Otherwise dropping ma y cause injury . • P oor pr int quality may occur . ■ A state where the printer ventilation holes are obstructed by a nearby wall or other equipment. ■ A state wh ...

  • Citizen Systems CT-S2000 - page 8

    — 5 — PRECA UTIONS IN HANDLING THE PRINTER Please observe the following precautions for power source and power cord: ■ Do not plug or unplug the power cord with a wet hand. ■ Use the printer only at the specified supply voltage and frequency . ■ Use only the specified AC adapter with the printer . ■ Check to make sure that the supply ou ...

  • Citizen Systems CT-S2000 - page 9

    — 6 — Caution label is attached on the position shown in the following figure. Carefully r ead the precautions in handling before using the printer . THIS LABEL INDICA TES THE RISK OF ANY INJUR Y DUE TO “HIGH TEMPERA TURE” OF THE PRINT HEAD. To prevent possible malfunction or failure observe the following. ■ A void operating the printer w ...

  • Citizen Systems CT-S2000 - page 10

    — 7 — Observe the following precautions for daily maintenance. ■ When cleaning the printer , always turn it off and unplug it from the supply outlet. ■ Use a soft, dry cloth for cleaning the surface of the printer case. ■ For severe stains, use a soft cloth slightly dampened with water . ■ Never use organic cleaning solvent such as alco ...

  • Citizen Systems CT-S2000 - page 11

    — 8 — THE T ABLE OF CONTENTS 1. GENERAL OUTLINE .................................................................... 9 1.1 Features .......................................................................................... 9 1.2 Unpacking ..................................................................................... 10 1.3 Model Classifi ...

  • Citizen Systems CT-S2000 - page 12

    — 9 — 1. GENERAL OUTLINE The CT -S2000/CT -S2000DC are thermal line printers designed for use with a broad array of terminal equipment including data, POS, and kitchen terminals. With extensive features, they can be used in a wide range of applications. 1.1 Features ● Compact, easy-to-use universal design. ● Drop-in Paper Roll mechanism fac ...

  • Citizen Systems CT-S2000 - page 13

    — 10 — 1.2 Unpacking When unpacking the printer , confirm that the following are provided: ● Printer: 1 ● AC adapter (Option, only for CT -S2000DC): 1 ● AC power cord (Option, only for CT -S2000DC): 1 ● Sample paper roll: 1 roll ● User’ s manual (This manual): 1 CT -S2000 (AC power type) Sample paper roll User’ s manual (This manu ...

  • Citizen Systems CT-S2000 - page 14

    — 11 — 1.4 Basic Specifications Item Specifications Model CT -S2000 P A, CT -S2000 RS, CT -S2000DC P A, CT -S2000DC RS Print method Line thermal dot print method Print width *1 80 mm/640 dots, 72 mm/576 dots, 54.5 mm/436 dots, 54 mm/432 dots Dot density 8 × 8 dots/mm (203 dpi) Print speed 220 mm/s (Fastest, print density 100 %), 1760 dot lines ...

  • Citizen Systems CT-S2000 - page 15

    — 12 — 2. EXPLANA TION OF PRINTER P AR TS 2.1 Printer Appearance Printer cover Power switch Operation panel Cover open button Rear connector (Front view) (Rear view) ● Printer cover Paper is loaded under this cover . ● Cover open button To refill or replace paper , open the printer cover by lifting the cover open button. ● Power switch Th ...

  • Citizen Systems CT-S2000 - page 16

    — 13 — ● POWER LED Illuminated when the printer power is on and off when the printer power is off. May blink or light in a special mode or in case of failure. ● ERROR LED Illuminated or blinks when paper is empty or in case of failure. The interval length of blinking represents the type of error . ● FEED button Pressing this button once c ...

  • Citizen Systems CT-S2000 - page 17

    — 14 — 2.3 Other Built-in Functions ● Buzzer This printer has a built-in buzzer . It is operated in case of an error , operation, or by a command. ● User memory Allows downloading of user -defined characters and logo data in the nonvolatile memory . This data remains stored even after the printer power is off. For the registration method, r ...

  • Citizen Systems CT-S2000 - page 18

    — 15 — 3. PREP ARA TION 3.1 Connecting the AC Power Cord 1. Tu rn off the pr inter pow er . 2. ● F or AC po wer type (with built-in pow er supply), connect the AC po wer cord t o the AC inlet at the bac k of the printer and plug the AC po wer cor d into the w all outlet. ● For DC po wer type, connect the AC adapter cable connect or to the p ...

  • Citizen Systems CT-S2000 - page 19

    — 16 — Printer Pin Signal 2 TXD 3R X D 4R T S 6 DSR 7S G 20 DTR PC Signal Pin FG 1 TXD 2 RXD 3 CTS 5 DSR 6 SG 7 DTR 20 3.2 Connecting Interface Cables Confirm that the power switch is OFF and connect the interface cable. Orient the interface cable terminal correctly and insert it into the interface connector . CAUTION! ■ When disconnecting th ...

  • Citizen Systems CT-S2000 - page 20

    — 17 — CAUTION! DO NOT connect any other device than the specified cash drawer to the cash drawer kick-out connector . (DO NOT connect a telephone line either .) 3.3 Connecting the Cash Drawer Cash drawer kick-out connector Cash drawer cable connector (1) Connector Pin Configuration (2) Electrical characteristics 1) Driving voltage: 24 VDC 2) D ...

  • Citizen Systems CT-S2000 - page 21

    — 18 — 80 mm 58mm 60mm 3.4 Precautions in Installing the Printer The printer must only be operated horizontally . Do not operate vertically or install on a wall. Horizontal position Ve rtical position CAUTION! DO NOT use the printer under the following conditions. ■ A state subject to vibration or unstable state. ■ A state with this product ...

  • Citizen Systems CT-S2000 - page 22

    — 19 — 3.6 Setting DIP Switch The DIP switch is present on the serial interface board. Remove the board fixing screws, take out the interface board, and then set the DIP switch. The function of each switch is as shown below . Baud Rate (bps) S witch No . Function ON OFF DIP switch Interface board mounting screws CAUTION! When setting the DIP sw ...

  • Citizen Systems CT-S2000 - page 23

    — 20 — 4 3 2 1 3.7 Adjusting the Paper Near -end Sensor 1. Lightly push in the paper near -end sensor unit. 2. Mov e the paper near -end sensor unit to the r ight and left while k eeping to press it. The sensor position is as shown below depending on the diamet er of the roll paper used. Sensor P osition **1 φ 22 φ 18 *2 φ 25 φ 22 3 φ 29 ? ...

  • Citizen Systems CT-S2000 - page 24

    — 21 — 4. MAINTENANCE AND TROUBLESHOOTING 4.1 Setting/Replacing the paper roll CAUTION! ■ Always use the specified types of paper roll. ■ Confirm that the paper roll is set correctly . ■ When the paper is skewed and not extended straightforward from under the printer cover , open the printer cover and adjust the paper correctly . ■ When ...

  • Citizen Systems CT-S2000 - page 25

    — 22 — 4.3 Cleaning the Print Head 1. Tu rn the pr inter po wer of f . 2. Open the pr inter co ver . 3. W ait sever al minutes. Wipe off an y debris on the heating element of the head using a cott on swab soak ed in ethyl alcohol. CAUTION! The print head is hot immediately after printing. DO NOT touch it with your hand. DO NOT touch the heating ...

  • Citizen Systems CT-S2000 - page 26

    — 23 — 4.5 Hexadecimal Dump Printing This function is to print all received data in hexadecimal numbers. If problems such as missing data, data duplication, etc. should occur , this function allows checking whether or not the printer is receiving data correctly . Set paper to the printer and keep the printer cover open. With the FEED button pre ...

  • Citizen Systems CT-S2000 - page 27

    — 24 — (Unit: mm) 207 147 147 5. OTHER 5.1 External Views and Dimensions ● Power switch operation error If you turn power on again just after powering of f, an error may occur . Before turning power on again, wait till POWER LED goes off completely after powering off. Lighting and blinking status of each error including the above is shown bel ...

  • Citizen Systems CT-S2000 - page 28

    — 25 — 3 44 41 . 5 32 . 5 d D 65~85 Paper width 83 +0 − 1 Maximum print area 80 Maximum print area 72 φ 102 or less Printing surface (Unit: mm) 5.2 Printing Paper Use the print paper shown in the following table or the paper with equivalent quality . P aper T ype Pr oduct Name Recommended thermal TF50KS-E2D from Nippon Paper paper roll PD150 ...

  • Citizen Systems CT-S2000 - page 29

    — 26 — 5.3 Manual Setting of Memory Switch Memory switches can be set manually or by a command. For manual setting, refer to the next page. The function of each memory switch is shown in the following table. (The white-on-black characters are factory setting.) S witch No . Setting 0 (OFF) 1 (ON) Memory SW1-1 Power ON Info V alid Not send SW1-2 ...

  • Citizen Systems CT-S2000 - page 30

    — 27 — S witch No . Setting Default Set V alues Memory SW7-1 Baud Rate 19200 bps/ 1200 bps, 2400 bps, 4800 bps, 9600 bps, 9600 bps** 19200 bps, 38400 bps, 57600 bps, 115200 bps SW7-2 Data Length 8bits 7bits, 8bits SW7-3 Stop Bit 1bit 1bit, 2bits SW7-4 Parity NONE NONE, EVEN, ODD SW7-5 Flow Control DTR/DSR DTR/DSR, XON/XOFF SW7-6 DMA Control V a ...

  • Citizen Systems CT-S2000 - page 31

    — 28 — 2. Selecting memory switch When the FEED button is pressed short (within 2 seconds), printing occurs in the order of “Memory SW1” → “Memory SW2” → “Memory SW3” → ......“Memory SW10” → “Save T o Memory” → “Memory SW1” → ...... repeatedly . When the memory switch you want to change is reached, press and ...

  • Citizen Systems CT-S2000 - page 32

    T A74902-10F 1.10E-0804 Printed in Japan ...

Manufacturer Citizen Systems Category Printer

Documents that we receive from a manufacturer of a Citizen Systems CT-S2000 can be divided into several groups. They are, among others:
- Citizen Systems technical drawings
- CT-S2000 manuals
- Citizen Systems product data sheets
- information booklets
- or energy labels Citizen Systems CT-S2000
All of them are important, but the most important information from the point of view of use of the device are in the user manual Citizen Systems CT-S2000.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Citizen Systems CT-S2000, service manual, brief instructions and user manuals Citizen Systems CT-S2000. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Citizen Systems CT-S2000.

Similar manuals

A complete manual for the device Citizen Systems CT-S2000, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Citizen Systems CT-S2000 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Citizen Systems CT-S2000.

A complete Citizen Systems manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Citizen Systems CT-S2000 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Citizen Systems CT-S2000, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Citizen Systems CT-S2000, that we can find in the current document
3. Tips how to use the basic functions of the device Citizen Systems CT-S2000 - which should help us in our first steps of using Citizen Systems CT-S2000
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Citizen Systems CT-S2000
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Citizen Systems CT-S2000 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Citizen Systems CT-S2000?

Use the form below

If you did not solve your problem by using a manual Citizen Systems CT-S2000, ask a question using the form below. If a user had a similar problem with Citizen Systems CT-S2000 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)