English dropdown-ico

Manual North Star 10 kW

53 pages 2.22 mb
Download

Go to site of 53

Summary
  • North Star 10 kW - page 1

    ...

  • North Star 10 kW - page 2

    1 FCC Statement Note: This equipment has been tested and found to com ply with the li mits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable prot ection against harmful interference in a normal installation. This equipment generates, uses and can radiate radio frequency energy and, i ...

  • North Star 10 kW - page 3

    4 Disclaimer As Northstar is continuously improvi ng this prod uct we retain the right to make changes to the product at any time which may not be reflected in this version of the manual. Please contact your nearest Northstar distributor if you require any furt her assistance. It is the owner’s sole responsibility to install and use the instrumen ...

  • North Star 10 kW - page 4

    Contents 1 FCC Statement 2 2 Industry Canada 2 3 Compliance Statement 2 4 Disclaimer 3 5 Warranty 3 6 Feedback from you 3 7 Preface 7 8 Introduction to the Northstar radar 9 9 Check the 25 kW radar parts 9 10 25 kW radar system overview 13 11 Install the radar 14 11.1 Choose the sca nne r location ................................................... ...

  • North Star 10 kW - page 5

    11.2 How to find the optimum hei ght for th e scanner ................................................................................. ....................... 17 11.3 How to find the ma xi mum detecti on range ........................................................................................ ........................... 18 11.4 How to reduce ...

  • North Star 10 kW - page 6

    15 Maintenance 45 15.1 General main tena nce ............................................................................................................ ................................................. 45 15.2 Scanner ma in tenance .................................................................................................................... ...

  • North Star 10 kW - page 7

    7 Preface This manual explains how to install the scanner and th e radar processor. It al so explains how to set up the radar system after installation and gives information on troubleshooting. This manual is supplementary to the Northstar 6000i/6100i Installation and Operation Manual and the Northstar 8000i System Installation documentation. This ...

  • North Star 10 kW - page 8

    Only qualified personnel should install or service this equi pment. Installation or servicing work that is done by non-qualified personnel can resu lt in equipment breakdown, poor performance of the equipment, fire, electrical and physical hazards, injury or death. Wear safety equipment such as a hard hat and a safety belt at all times when install ...

  • North Star 10 kW - page 9

    8 Introduction to the Northstar radar The Northstar radars a re designed as an option available to the Northstar 6000i , 6100i, or 8000i systems. A variety of scanner models are available (2 kW , 4 kW, 6 kW, 10 kW and 25 kW) to suit different customer requirements. Eac h scanner model has a corresp onding radar processor model. 9 Check the 25 kW ra ...

  • North Star 10 kW - page 10

    1 Installation template MTZ303535 LA000414A 1 Mounting template ????? 1 Packing list ???? NS00310X interconnection cable - order separately Quantity Item Part name Part number 1 Interconnection cable NS003105 length 65.5 ft (20 m) OR NS003106 length 98.4 ft (30 m) NS004784R 25 kW radar processor standard components Quantity Item Part name Part numb ...

  • North Star 10 kW - page 11

    Spare 10 A fuse (motor) ????? 4 Mounting screw HR000061 NS004794R 25 kW open array standar d components Quantity Item Part name Part number 1 25 kW open array NS004794 1 Assembly instructions sheet LA000277A 1 Packing list ???? 4 Brass washers ???? 4 Spring washers ??? 4 M10x35 bolts ??? NS00481X cable for 8000i installation only - order separately ...

  • North Star 10 kW - page 12

    NS003107 cable for 6000i and 6100i installations only - supplied with 6000i and 6100i system Quantity Item Part name Part No 1 Radar communications cable for 6000i and 6100i installations ONLY. NS003107 NS003108 Optional extension cable for 6000i and 61 00i installations only - order separately Quantity Item Part name Part no. 1 Radar communication ...

  • North Star 10 kW - page 13

    10 25 kW radar system overview The radar system is intende d for use in a marine environment. The 25 kW radar system consists of a sca nner and an open array, connected to the 2 5 kW radar processor by a prefabricated inte rconnection cable which is availa ble in two lengths (NS003105 o r NS003106). where A is the radar processor, B is th e vessel& ...

  • North Star 10 kW - page 14

    11 Install the radar A radar unit should only be installed by a qualifie d marine technician, as potentially lethal high voltage is present along with heavy rotating parts. There is a transmit interlock that prevents radar transmissions if the scanner is not rotating. However, a high voltage remains fo r a period of time after the system is turned ...

  • North Star 10 kW - page 15

    DON'T DO THIS!  DON'T install the scanner too high up, wher e it s weight will alter the stability of the vessel and cause degradation of the radar picture over short ranges (see "How to find the optimum height for the scanner").  DON'T install the scanner close to lamps or ex haust outlets. The heat emissions may cau ...

  • North Star 10 kW - page 16

    11.1.1 Power boat installations Normally, you should install the scanner horizonta lly, to p roduce an equal sweep around the powe r boat: However, when the power boat is traveling at high speed, the bow rises up out of the water and if the elevation angle (trim) of the bow is raised up so that it equals, or exceeds, 50% of the vertical bea m width ...

  • North Star 10 kW - page 17

    11.1.2 Yacht installations Normally you should install the sc anner horizontally, to produce an equal sweep around the yac ht. However, a yacht heels over to the lee side, and when the heel angle ex ceeds 50% of the vertical beam width of the radar, this can cause two pr oblems:  on the windward side of the yacht, the beam is projected too high ...

  • North Star 10 kW - page 18

    An example of an A-B Line is shown in the picture. If you install the scanner below the A-B line, the scanner will be too low. It will be difficult to acquire distant targets and the superstructure will be more likely to impede th e passage of the beam and generate fals e echoes. If the scanner is installed too high above the A-B line, the beam wil ...

  • North Star 10 kW - page 19

    Calculations using the formula show that, at this distance, the radar can only detect objects that are more than 25 ft (7.6 m) high, which means that Island A is shown on the radar but Island B is not shown. Remember that:  the maximum detection range of the radar is limited by the curva ture of the Earth's surface under normal conditions o ...

  • North Star 10 kW - page 20

    If the trestle height (A) is less than 2 m high, use the angle joint method as shown: If the trestle height (A) is more than 2 m high, in stall a radar mast secured with guy wires as shown: 11.6 25 kW radar dimensions The 25 kW radar has an open array with a rotation diameter of 89.4" (2270 mm). Ensure that the open array will be able to rotat ...

  • North Star 10 kW - page 21

    11.7 Install the 25 kW scanner unit Tape the paper installation template securely to the chosen location si te. Before dril ling, check that:  the location site is not more than 0.6" (15 mm) thick, to ensure that you can use the bolts supplied.  you've oriented the template co rrectly so that the front of the scanner unit faces the ...

  • North Star 10 kW - page 22

    11.9 Install the radar pr ocessor Install the radar processor in a dry location away from spray, rain, drips, and condensa tion. The location site must allow you to easily connect the radar proc essor to the ship's ground, the interconnection cable, the power cable, and the 6000i and 6100i radar communications cable or the 8000i network cable. ...

  • North Star 10 kW - page 23

    12 Wire the radar system Always install a separate circuit breaker or sep arate fuse for the radar system circuit. 12.1 Wiring guidelines Most installation problems are caused by shortcuts ta ken with system cables. When wiring the rad ar:  DON'T make sharp bends in the cables.  DON'T run cables in a way that allows wa ter to flow d ...

  • North Star 10 kW - page 24

    4. Tear away the tape (A ) then unravel the shield mesh and wrap this around the washer as shown. 5. Check that the i nterconnection cable i s positioned so tha t you can easily connect it to the J connectors, as s hown: 6. Screw down the cab le holders and clips to k eep the interconnection cable in pl ace inside the scanner. Th e interconnection ...

  • North Star 10 kW - page 25

    7. Connect the five inte rconnection cable connectors (B, C, D, E, and F) to the J connectors as follows: Cable connector J connector B (P2) J2 C (P1) J1 D (P3) J3 E (P4) J4 F (P5) J5 8. Close the scanner with the screws. The wiring details for the con nector ends B, C, D, E, and F are as follows: NS003105/NS003106 Interconnection cable - connector ...

  • North Star 10 kW - page 26

    15 Shield line #24 1 16 Orange (medium) #22 3 Shell Braid shield 12.3 25 kW radar processor connectors There are four interface connecto rs on the rear of th e 25 kW radar processor , plus a chassis earth. Northstar 25 kW Radar Installation Manual 26 ...

  • North Star 10 kW - page 27

    You can connect the radar processo r to either the Northstar 6100i OR to the N orthstar 8000i, but no t to both simultaneously. 25 kW radar processor interface connectors Connector name Connector function Connects to... Network Ethernet communications for the 8000i 8000i network, using the 8000i network cable (NS00481X) Power (+Ve and -Ve) Power in ...

  • North Star 10 kW - page 28

    The front view of the interc onnection cable is shown: The interconnection cable pin detail s are pr ovided here for information, in case the connect or needs to be removed to feed the cable, or in case the cable need s to be shortened. Pin Color AWG Size Signal name 1 Blue / Gray (big) #16 Motor Ground 2 Purple / Brown (big) #16 Motor Ground 3 Whi ...

  • North Star 10 kW - page 29

    12.6 Install the 25 kW open array IMPORTANT: Install the open array onto the scanne r ONLY after you've connected the 25 kW interconnect ion cable. Use the assembly sheet provided and chec k that yo u've got all the componen ts shown. Follow the instructions on the assembly sheet to install the open array. Northstar 25 kW Radar Installati ...

  • North Star 10 kW - page 30

    12.7 Connect the 25 kW radar processor to a 6000i or 6100i display The following diagram shows the recommended met ho d for connecting the radar p rocessor to a 6000i or 6100i display unit: Item Function A Junction box Northstar 25 kW Radar Installation Manual 30 ...

  • North Star 10 kW - page 31

    B To NMEA Device 1 C To NMEA Device 2 D To Smartcraft E Remote power F Circuit breaker/fuse box G Optional radar communicati ons extension cable (NS003108) H Vessel's Ground I NTSC Video Input J Fuse (7A) K GPS antenna L Power M NMEA N Ethernet 0 AUX P VGA (out) 12.7.1 Connect the radar communications cable (NS003107) to the junction box The f ...

  • North Star 10 kW - page 32

    NMEA 1 OUT GROUND Blue/White 8 Blue/White NMEA 2 IN A White/Brown 6* White/Brown 1 Green NMEA 2 IN B Brown/White 2* Brown/White 2 Red NMEA 2 IN GROUND White 5* White NMEA 2 OUT A Yellow 15* Yellow 7 Orange NMEA 2 OUT B Orange 11* Orange 8 Blue NMEA 2 OUT GROUND Black 10 Black 12 Yellow RS-232 GROUND Tan 17* Tan 1 White RS-232 RX Green 16* Green 3 G ...

  • North Star 10 kW - page 33

    Connector 3 - SmartCraft pin assignments 12.7.2 Configure the remote power control for a 6000i or 61 00i (common power source) IMPORTANT: This remote po wer control option works cor rectly only when the 6000i o r 6100i and the radar processo r share the same power earth a nd are located 16.5 ft (5 m) or less apart. A simplified diagram of the power ...

  • North Star 10 kW - page 34

    The radar processor ha s two remote power inputs with opposite active states which a re OR’ed together. Pin 10 input (active low) is used by the 6000i or 61 00i systems and Pin 12 input (active high) is used by the 8000i syste m. Pin 12 is tied to ground through the NS003107 cable , to allow control through Pin 10. The radar processor has a n act ...

  • North Star 10 kW - page 35

    E Relay with (normally) closed contact F Fuse G NMEA port H Power port I Fuse /Breaker board J and K Battery  If you want the radar to power ON automatica lly when the radar pro cessor is powered ON, omit the relay and leave Pin 10 and 12 on Connector 1 (the NMEA/Com ms connector) as No Connect. 12.8 Connect the 25 kW radar proc essor to an 8000 ...

  • North Star 10 kW - page 36

    12.9 Configure the remote power control for an 8000i NOTE: At the time of printing this manual, the 8000i does not support re mote power control of network modules. This feature will be added in future release. The radar processor supports this feature through Pin 12 on the NMEA/Comms port. If you want the radar proces sor to power ON automa ticall ...

  • North Star 10 kW - page 37

    Ideally, the compass should draw less than 100 mA. (I f this is not possible, power the c ompass using a separate 12 V source.) 12.12 Connect the power cable The power cable to the radar processor is NOT suppl ied for either the 6000i or 6100i system or the 8000i system. Power must be supplied through a fu se/breaker elem ent located at the power s ...

  • North Star 10 kW - page 38

    The eyelets must be crimped or soldered at both locations (A) and the method of connection to the vessel's hull is shown at (B). If you are installing the radar processor on a vessel with a non-metallic hull, connect the radar processor Chassis Earth to the vessel's ground networ k. If a vessel's ground netw ork is not available, lea ...

  • North Star 10 kW - page 39

    14 Set up the radar with the Nort hstar 6000i or 6100i 14.1 Turn the radar on and off 14.1.1 Before you turn on the radar for the first time To extend magnetron lifetime, yo u're recommended to leave the rada r in Standby mode for 30 minutes when activating the radar for the VERY FIRS T time. (When the radar is in Standby mode, it's NOT t ...

  • North Star 10 kW - page 40

    14.2 Configure the navigator communications IMPORTANT: If you are going to operate t he radar without a heading sensor, ignore this section and set up the radar as described in "D isable the header sensor input". To enable the radar to communicate with the na vigator, set up the radar option on the navigator's PORT 2 SETUP screen as ...

  • North Star 10 kW - page 41

    14.4 Calibrating the radar You must calibrate the newly installed radar by adjusting the trigger delay and the heading calibration. To evaluate medium and short rang e returns, you are recommended to perform the calibration at sea in a normal operating environment an d under fair weather conditions. There should be an area of at least 3 nautical mi ...

  • North Star 10 kW - page 42

    2. Press Page 2 , Page 3 , Page 4 then Install... and then Tune... . 3. Press STC Curve then us e the keypad to enter a curve number f rom 0 to 8. 14.4.4 Set the trigger delay There are two methods that you can use to set the trigger delay. The two methods should produce very similar settings. Method 1 is easier to perform but Method 2 ma y produce ...

  • North Star 10 kW - page 43

    IMPORTANT: Make sure the heading sensor is calibrated according to the manufacturer's recommendations. 1. When performing a sea tr ial of the vessel, set a straight course for a solid object such as a lighthouse, jetty or radar nav igation marker th at is at least 1 nautical mile distant as refere nced on the c hart. 2. Press CHART to display ...

  • North Star 10 kW - page 44

    ranges, and the Range Rider will store thes e setti ngs for each range. Th en, when you select a particular range again, the settings are already optimized.  Manual is a fully manual function in which yo u will usually need to adjust the settings manually each time you change the range. Gain and Sea Clutter appearance settings are available in A ...

  • North Star 10 kW - page 45

    15 Maintenance Before doing any maintenance work, alwa ys ensure that the radar system is turned OFF at the main power source. If a rectifier unit is used, turn OFF the power supply to th is too. Remember that high voltages from the rectifier unit are always present, even if the radar is not ope rating, and these can cause severe injury or death. 1 ...

  • North Star 10 kW - page 46

    16 Troubleshoot the radar This appendix gives information on fixing possible problems with the radar. Many problems are caused by:  faulty or loose contacts at switches and relay points  poor adjustment of the radar (particu larly inadequate tuning adjustment)  poor maintenance (particularly of the cables) You'll save yourself a cons ...

  • North Star 10 kW - page 47

     check for physical damage to the cables (such as fraying) and for any loose connections  check for water damage to the radiator or to the cables between the radar components  check that the tuning is adjusted correctly  check the magnetron and replace if necess ary (see the Service Manual)  check the modulator circuit and replace if ...

  • North Star 10 kW - page 48

     the affected piece of equipm ent and/or the an tenna is not located within the radar beam. (See the section "Install the ra dar" for information about the optimum installation hei ght and the radar beam width)  the cables supplied with the equipment ha ve be en installed correctly. In particular, check for loose connections and loo ...

  • North Star 10 kW - page 49

    3. If the antenna does not turn, skip to th e section "If the scanner fails to turn". No, range rings or range scale information are not displayed. 1. Verify that the serial data cable wiring is correct for the communicati ons cable as shown in the section "Connect th e communications cable to the junction box". Northstar 25 kW ...

  • North Star 10 kW - page 50

    17 Manual tuning procedure for the 6000i or 6100i system NOTE: The following manual tuning proce dure is provided only for possible situations where the unit's automatic tuning does not perform well with a Northstar 6000i or 6100i system. At present, Northstar is not aware of any such situation and recommends that automatic tuning be used, unl ...

  • North Star 10 kW - page 51

    18 25 kW radar system specifications NS-RDR1257MO 25 kW scanner Scanner type Open array DC input 21.6 V to 31.2 V (DC 24 V systems ONLY) Scanner dimensions 7.45 ft [2270 mm] (swing circle) by 1.2 ft (H) [356(H) mm] Scanner weight 119 lb (54 kg) ± 10% Vibration Amplitude 2 x 13.2 Hz, ± 0.03" [1 mm] ± 10% Amplitude 13.2 Hz to 100 Hz, grav ity ...

  • North Star 10 kW - page 52

    Processor model NS004784 Processor dimensions Width 5.6" (142 mm) Height 2.2" (56 mm) Length 7.9" (200 mm) Processer weight 1.9 lbs (870 g) Vibration EN60945 Waterproof No rating Temperature range +5ºF to +131ºF (–15ºC to +55ºC) Relative humidity 95% at 104ºF (+40ºC) Power up time Approximately 35 seconds DC input 10.8 V to 3 ...

  • North Star 10 kW - page 53

    25 kW Installation back Cover ADD ARTWOR K ...

Manufacturer North Star Category Radar Detector

Documents that we receive from a manufacturer of a North Star 10 kW can be divided into several groups. They are, among others:
- North Star technical drawings
- 10 kW manuals
- North Star product data sheets
- information booklets
- or energy labels North Star 10 kW
All of them are important, but the most important information from the point of view of use of the device are in the user manual North Star 10 kW.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals North Star 10 kW, service manual, brief instructions and user manuals North Star 10 kW. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product North Star 10 kW.

Similar manuals

A complete manual for the device North Star 10 kW, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use North Star 10 kW by users. Manuals are usually written by a technical writer, but in a language understandable to all users of North Star 10 kW.

A complete North Star manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual North Star 10 kW - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the North Star 10 kW, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the North Star 10 kW, that we can find in the current document
3. Tips how to use the basic functions of the device North Star 10 kW - which should help us in our first steps of using North Star 10 kW
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with North Star 10 kW
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of North Star 10 kW in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning North Star 10 kW?

Use the form below

If you did not solve your problem by using a manual North Star 10 kW, ask a question using the form below. If a user had a similar problem with North Star 10 kW it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)