English dropdown-ico

Manual Weider 8530

25 pages 0.77 mb
Download

Go to site of 25

Summary
  • Weider 8530 - page 1

    USERÕS MANUAL QUESTIONS? As a manufacturer , we are com- mitted to providing complete customer satisfaction. If you have questions, or find that there are missing or damaged parts, we will guarantee you complete sat- isfaction through direct assis- tance from our factory . TO A VOID UNNECESSAR Y DELA YS, PLEASE CALL DIRECT TO OUR T OLL-FREE CUSTOM ...

  • Weider 8530 - page 2

    2 IMPORT ANT PRECAUTIONS W ARNING: T o reduce the risk of serious injury , read the following important precautions before using the home gym system. 1. Read all instructions in this manual and in the accompanying literature before using the home gym system. 2. Use the home gym system only on a level surface. Cover the floor beneath the home gym sy ...

  • Weider 8530 - page 3

    3 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 74 in. Width: 60 in. Length: 54 in. Foot Plate Low Pulley Station High Pulley Station Lat Bar Leg Lever Butterfly Arms Squat Arm Press Arm Weight Stacks Backrest VKR Arms Weight Pin Thank you for selecting the versatile WEIDER ¨ 8530 Home Gym System. The WEIDER ¨ 8530 of fers a selection of weight ...

  • Weider 8530 - page 4

    4 ASSEMBL Y 1 74 56 3 3 8 11 51 27 1 4 3 1 51 27 High Side 5 1. Before beginning assembly , be sure that you have read and understand the infor- mation in the box above. Press a 2Ó Inner Cap (27) into the indicated end of the Stabilizer (5). Press 2Ó Outer Caps (51) onto the other two locations on the Stabilizer . Press a 2Ó Inner Cap into the e ...

  • Weider 8530 - page 5

    4 2 3 5 2. Insert two 5/16Ó x 2 1/2Ó Carriage Bolts (1) up through the Base (4). Slide the Front Upright (42) onto the 5/16Ó x 2 1/2Ó Carriage Bolts (1) in the Base (4). Hand-tighten a 5/16Ó Nylon Locknut (3) onto each Carriage Bolt. Do not tighten the Nylon Locknuts yet. Press a 1Ó Inner Cap (6) into the Front Upright (42). Press a 2Ó Inner ...

  • Weider 8530 - page 6

    5 6 6 5. Press a Weight Tube Bumper (64) into the end of a Weight T ube (63). Insert the Weight T ube into the front stack of Weights (25). Be sure that the pins on the Weight T ube are sitting in the pin grooves in the top Weight. Lubricate the inside of the holes in a T op Weight (65). Set the T op Weight onto the front stack of Weights (25). Ins ...

  • Weider 8530 - page 7

    7. Attach the upper ends of the Long Weight Guides (62) to the T op Frame (55) with a 5/16Ó x 6Ó Bolt (60), two 1/2Ó x 3/4Ó Spacers (61), and a 5/16Ó Nylon Locknut (3). Be sure that the Pulley Bracket (20) is in front of the right Long Weight Guide (62) as shown. Attach the upper ends of the Short Weight Guides (73) to the T op Frame (55) with ...

  • Weider 8530 - page 8

    8 1 1. Lubricate both axles on the T op Frame (55). Slide the Right Arm (48) onto the right axle. Be careful not to confuse the Right Arm with the Left Arm (47); note the position of the ÒVÓ Pulley (50) to identify the Right Arm. Be sure that the upper end of the Right Arm is behind the indicated bracket on the T op Frame (55). T ap two 1Ó Retai ...

  • Weider 8530 - page 9

    9 During steps 13 to 25, refer to the CABLE DIA- GRAM on page 19 of this manual. Identify the three cables by their lengths, and note the positions of the cable traps. IMPORT ANT : Do not overtighten the bolts and nuts securing the pulleys. The pulleys must turn freely . 13. Locate the Medium Cable (58). Route the Medium Cable around the indicated ...

  • Weider 8530 - page 10

    10 17. Route the Medium Cable (58) around the 3 1/2Ó Pulley (15) attached to the bracket on the T op Frame (55). T ighten the 3/8Ó x 2Ó Bolt (12) and the 3/8Ó Nylon Locknut (21). (Note: This Pulley is pre-assembled. It has been shown disassembled for easy part identifica- tion.) Be sure that the Cable is in the groove of the Pulley and that the ...

  • Weider 8530 - page 11

    11 21. Attach the Medium Cable (58) to a Small ÒUÓ- Bracket (71) with a 1/4Ó Nylon Locknut (2) and a 1/4Ó Flat W asher (10). Do not tighten the 1/4Ó Nylon Locknut. It should be threaded onto the Cable only a couple of turns. Attach the Small ÒUÓ-Bracket (71) to the indi- cated Weight Tube (63) with a 5/16Ó x 1 3/4Ó Bolt (24) and a 5/16Ó N ...

  • Weider 8530 - page 12

    12 23. Route the Long Cable (72) around the 3 1/2Ó Pulley (15) on the T op Frame (55). T ighten the 3/8Ó Nylon Locknut (21) and the 3/8Ó x 2Ó Bolt (not shown). See inset drawing. Wrap the Long Cable (72) around a 3 1/2Ó Pulley (15). Attach the Pulley and a Cable T rap (66) to the bracket on the Stabilizer (5) with a 3/8Ó x 2Ó Bolt (12) and a ...

  • Weider 8530 - page 13

    13 25. See inset drawing A. Note: The inset draw- ing shows the view from the other side of the Squat Arm Upright (56). Wrap the Long Cable (72) around a ÒVÓ-Pulley (50). Attach the ÒVÓ-Pulley and a Long Cable T rap (31) to the top hole in the Squat Arm Upright with the 3/8Ó x 5Ó Bolt (67), the 5/8Ó x 3/8Ó Spacer (76), a 3/8Ó Flat W asher ...

  • Weider 8530 - page 14

    14 28. Press a 1 1/2Ó Inner Cap (32) into the Leg Lever (29). Lubricate the 5/16Ó x 2 1/4Ó Bolt (33). Attach the Leg Lever (29) to the Seat Frame (36) with the 5/16Ó x 2 1/4Ó Bolt and a 5/16Ó Nylon Locknut (3). Insert the 5/16Ó x 2Ó Eyebolt (35) into the Leg Lever (29) from the direction shown. T ighten a 5/16Ó Nylon Locknut (3) with a 5/1 ...

  • Weider 8530 - page 15

    32. Wet the handle on the Right VKR Arm (80) with soapy water . Slide a 5Ó Plastic Grip (83) onto the Handle. Press a 1Ó Round Inner Cap (49) into the bottom of the handle. Attach a 5Ó Plastic Grip (83) and a 1Ó Round Inner Cap (49) to the handle on the Left VKR Arm (79) in the same manner . 33. Attach a VKR Armrest (78) to the Right VKR Arm (8 ...

  • Weider 8530 - page 16

    16 HOW T O USE THE HOME GYM SYSTEM The instructions below describe how each part of the home gym system can be adjusted. Refer to the exercise poster accompanying this manual to see how the home gym system should be set up for each exercise. IMPORT ANT : When attaching the lat bar or nylon strap, make sure that the attachments are in the cor- rect ...

  • Weider 8530 - page 17

    17 A TT ACHING AND REMOVING THE SEA T T o attach the Seat (13), set the bracket on the Seat Frame (36) onto the indicated pins on the Front Upright (42). Attach the Seat Frame to the Front Upright with the 5/16Ó x 2 3/4Ó Carriage Bolt (14) and the Seat Knob (40). For some exercises, the Seat (13) must be removed. First, be sure that the chain is ...

  • Weider 8530 - page 18

    TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately . The home gym system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the type of cable used on the home gym system, can stretch slightly ...

  • Weider 8530 - page 19

    19 CABLE DIAGRAM The cable diagram below shows the proper routing of the Long Cable (72), the Medium Cable (58), and the Short Cable (23). Use the diagram to be sure that the three cables and cable traps have been assembled cor- rectly . If the cables have not been correctly routed, the home gym system will not function properly and damage may occu ...

  • Weider 8530 - page 20

    P ART LISTÑModel No. WESY85301 R0100A Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. Key No. Qty . Description 1 6 5/16Ó x 2 1/2Ó Carriage Bolt 2 4 1/4Ó Nylon Locknut 3 27 5/16Ó Nylon Locknut 4 1 Base 5 1 Stabilizer 6 1 1Ó Inner Cap 7 1 5/8Ó x 9/16Ó Spacer 8 9 5/16Ó Flat W asher 9 4 3/8Ó ...

  • Weider 8530 - page 21

    68 3 20 21 15 66 12 27 83 78 80 75 75 10 81 77 32 83 78 79 3 10 43 74 11 11 3 51 1 1 27 19 51 21 5 25 64 26 12 66 15 63 65 24 2 71 72 3 67 31 50 76 21 56 54 83 83 52 53 39 21 93 92 15 94 84 3 8 8 22 49 82 83 87 85 22 8 8 3 82 83 87 60 27 21 15 55 12 11 8 15 12 44 88 15 58 21 44 21 3 61 62 24 3 58 71 2 65 63 21 15 12 2 57 23 64 25 26 19 21 9 3 3 49 ...

  • Weider 8530 - page 22

    1" Retainer (69)Ð4 3/8" x 3 1/2" Bolt (16)Ð1 1/4" x 3/4" Screw (18)Ð2 5/16" x 5" Bolt (68)Ð1 3/8" x 3 3/4" Bolt (88)Ð4 3/8" x 8" Bolt (59)Ð1 Cable Clip (53)Ð2 1 1/4" x 2 1/2" Plastic Bushing (89)Ð2 1" x 7/8" Plastic Bushing (90)Ð2 5/16" x 6" Bolt (60)Ð2 3 ...

  • Weider 8530 - page 23

    1" Round Inner Cap (49)Ð6 1" Round Cover Cap (70)Ð2 3/4" Round Inner Cap (34)Ð4 1/2" x 3/4" Spacer (61)Ð4 5/16" x 2" Eyebolt (35)Ñ1 1 1/2" Inner Cap (32)Ð4 1 3/4" Inner Cap (44)Ð6 2" Inner Cap (27)Ð5 2" Outer Cap (51)Ð2 1" Inner Cap (6)Ð1 1" x 2" Inner Cap (87)Ð2 1/2&q ...

  • Weider 8530 - page 24

    5/16" Nylon Locknut (3)Ð27 1/4" Flat W asher (10)Ð13 5/16" Flat W asher (8)Ð7 3/8" Flat W asher (9)Ð4 1/4" x 2 1/2" Screw (43)Ð4 3/8" Nylon Locknut (21)Ð16 1/4" x 2" Machine Screw (81)Ð5 3/8" Jam Nut (92)Ð2 5/16" x 2 1/2" Carriage Bolt (1)Ð6 5/16" x 2 3/4" Carriage Bolt ...

  • Weider 8530 - page 25

    ORDERING REPLACEMENT P ARTS T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays). T o help us assist you, please be pre- pared to give the following information: 1. The MODEL NUMBER of the product (WESY85301) 2. The NAME ...

Manufacturer Weider Category Home Gym

Documents that we receive from a manufacturer of a Weider 8530 can be divided into several groups. They are, among others:
- Weider technical drawings
- 8530 manuals
- Weider product data sheets
- information booklets
- or energy labels Weider 8530
All of them are important, but the most important information from the point of view of use of the device are in the user manual Weider 8530.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Weider 8530, service manual, brief instructions and user manuals Weider 8530. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Weider 8530.

Similar manuals

A complete manual for the device Weider 8530, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Weider 8530 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Weider 8530.

A complete Weider manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Weider 8530 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Weider 8530, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Weider 8530, that we can find in the current document
3. Tips how to use the basic functions of the device Weider 8530 - which should help us in our first steps of using Weider 8530
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Weider 8530
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Weider 8530 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Weider 8530?

Use the form below

If you did not solve your problem by using a manual Weider 8530, ask a question using the form below. If a user had a similar problem with Weider 8530 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)