English dropdown-ico

Manual Furuno DFF3

32 pages 0.61 mb
Download

Go to site of 32

Summary
  • Furuno DFF3 - page 1

    NETW ORK SOUNDER DFF3 OPERA T OR'S MANU AL www .furuno .co .jp MODEL ...

  • Furuno DFF3 - page 2

    i IMPORTANT NOTICES • The descri ptions in thi s manual are intended for r eaders with a solid knowledge of English. • No part of this manual may be copied or reproduced without writ t en permission. • If this manual is lost or worn , contact your dealer about r epla cement. • The contents of this ma nual and equipment specific ations are s ...

  • Furuno DFF3 - page 3

    ii SAFETY INSTRUCTIONS Do not operate the equipment with wet hands. Electrical shock can result. Do not place liquid-filled containers on the top of the equipment. Electrical shock can result. Do not install the equipment where it may be subjected to rain or water splash. Fire or electrical shock can result if water gets inside the equipment. Use t ...

  • Furuno DFF3 - page 4

    SAFETY INSTRUCTIONS iii Standard compass Steering compass 0.95 m 0.60 m CAUTION CAUTION The transducer cable must be handled carefully, following the guidelines below. • Keep fuels and oils away from the cable. • Locate the cable away from chemicals. • Locate the cable away from locations where it might be damaged. Do not apply the power with ...

  • Furuno DFF3 - page 5

    iv TABLE OF CONTENTS FOREWORD .............. .............. ................... .............. .................. .............. ................... .... v SYSTEM CONFIGURATION ............ .............. ................... .............. ................... ............ v i 1. MOUNTING ......... ................... .............. ................ ...

  • Furuno DFF3 - page 6

    v FOREWORD A Word to the Owner o f the DFF3 Congratulations on your ch oice of the FURU NO DFF3 Network Sounde r. We are conf ident you will see why the FURUNO name has become synonymous with quality and reli abi lity. For 60 year s FURUNO Electric Com pany has en joyed an enviabl e reputation for qualit y marine electroni cs equipment . This dedi ...

  • Furuno DFF3 - page 7

    vi SYSTEM CONFIGURATION Basic configurati on shown with solid line. 100/1 10/1 15/ 220/230 V AC 1 φ , 50/60 Hz Network Sounder DFF3 12-24 VDC Low Freq. T ransducer High Freq. T ransducer Rectifier PR-62 Speed/T emperature Sensor ST -02MSB ST -02PSB T emperature Sensor T -02MTB T -02MSB T -03MSB DFF3 NETWORK SOUNDER ST-BY * HUB-100 (For NavNet) HUB ...

  • Furuno DFF3 - page 8

    1 1. MOUNTING 1.1 Equip ment Li sts Standard su pp ly Opti o nal su pp ly Name Type Code No . Qty Remarks Networ k Sounder DFF3 — 1 Spare Parts SP02-0 5601 001-033 -740 1 set Fuse Instal lation Mat erials CP02-085 00 000-011 -917 1 set - Power cable (3.5 m) - LAN ca ble (5 m fo r NavNet 3D) - Self- tapping scr ews Name Type Code No. Remarks Tran ...

  • Furuno DFF3 - page 9

    1. MOUNTIN G 2 Transdu cer , thru-hu l l pipe and tank com binations Output (W) Freq uenc y (kHz) Ship type Tran sduc er Thru- hull pipe Tank 1k/1 k 28/50 St eel 28F-8 50B-9B TWB -6000(2) T-6 56 FRP - - 28/88 St eel 28F-8 88B-8 TWB -6000(2) T-6 57 FRP - - 50/88 St eel 50B-9B 88B-8 TWB -6000(2) T-6 58 FRP - - 50/200 Steel 50/200- 1T or TFB-50 00(1) ...

  • Furuno DFF3 - page 10

    1. MOUNTING 3 2k/2 k 28/50 Ste el 28F-18 50B-12 TFB -7000(2) T-63 4 FRP T RB-1100(2 ) T-634-F 28/82 Ste el 28F-18 82B-35 R TFB-7000( 2) T-636 FRP T RB-1100(2 ) T-636-F 28/88 Ste el 28F-18 88B-10 TFB -7000(2) T-63 6 FRP T RB-1100(2 ) T-636-F 28/200 S teel 28F-18 200B -8/ 8B TFB-700 0(2) T-638 FRP T RB-1100(2 ) T-638-F Steel 28B L-6HR 200B -8/ 8B TFB ...

  • Furuno DFF3 - page 11

    1. MOUNTIN G 4 2k/3 k 28/150 S teel 28F-18 150B-1 2H TFB-70 00(2) T-637 FRP TRB -1100( 2) T -637 -F 50/107 S teel 50B-12 100B-1 0R TFB-70 00(2) T-643 FRP TRB -1100( 2) T -643 -F 50/150 S teel 50B-12 150B-1 2H TFB-70 00(2) T-644 FRP TRB -1100( 2) T -644 -F 3k/2 k 68/200 S teel 68F-30H 200B -8/ 8B TFB-70 00(2) T-647 FRP TRB -1100( 2) T -647 -F 107/2 ...

  • Furuno DFF3 - page 12

    1. MOUNTING 5 3k/3 k (con’t) 28/88 Steel 28BL-12H R 88F-126 H TFB-7000( 2) T-682 FRP T RB-1100(2 ) T-682-F Steel 28F -24H 88F-126 H TFB-7000( 2) T-682 FRP T RB-1100(2 ) T-682-F 28/150 S teel 28BL-12HR 150B-1 2H TFB-700 0(2) T-683 FRP T RB-1100(2 ) T-683-F Steel 28F -24H 150B-1 2H TFB-700 0(2) T-683 FRP T RB-1100(2 ) T-683-F 28/200 S teel 28BL-12H ...

  • Furuno DFF3 - page 13

    1. MOUNTIN G 6 3k/3 k (con’t ) 50/200 St eel 50BL-2 4H 200B-1 2H TFB-70 00(2) T-695 FRP TRB -1100( 2) T -695 -F Steel 50BL- 24HR 200B-1 2H TFB-70 00(2) T-683 FRP TRB -1100( 2) T -683 -F Steel 50F -24H 200B-1 2H TFB-70 00(2) T-683 FRP TRB -1100( 2) T -683 -F 68/150 S teel 68F-30H 150B-1 2H TFB-70 00(2) T-646 FRP TRB -1100( 2) T -646 -F 68/200 S te ...

  • Furuno DFF3 - page 14

    1. MOUNTING 7 2k (c on’t) 50 Steel 50B-12 TFB- 5000(1) T-61 1 FRP T RB-1000(1 ) T-611-F Steel 50BL-1 2 TFB-500 0(1) T-702 FRP T RB-1000(1 ) T-702-F Steel 50BL-1 2HR TFB-5000(1) T- 702 FRP T RB-1000(1 ) T-702-F 82 Steel 82B-35 R TFB-500 0(1) T-609 FRP T RB-1000(1 ) T-609-F 88 Steel 88B-10 TFB-500 0(1) T-609 FRP T RB-1000(1 ) T-609-F 200 Steel 200B ...

  • Furuno DFF3 - page 15

    1. MOUNTIN G 8 1.2 Netwo rk Sound er The network sounder can be install ed on a desktop, deck or on a bulkhead. When selec ting a mounting locati on for the network sounder, kee p the fol lo wing in mind: • The temperature and humidit y at the mounting site should be mod e rat e and stable. • Locate t he unit away f rom exhaust pipes and vents. ...

  • Furuno DFF3 - page 16

    1. MOUNTING 9 • A magneti c compass will be affected if the network sounder is placed too c lose to it . Observe the compass saf e distances noted i n t he safety inst ruc tions to prevent di sturbance to the mag- netic c ompass. Fasten the network sounder to the mounti ng l ocation with four self -tapping screws (5×20), refer- ring to the outli ...

  • Furuno DFF3 - page 17

    1. MOUNTIN G 10 1.5 Optio na l Te mp era t ure Sen so rs 1.5.1 Tr ansom mount temperature sensor T-02MTB • Fix the cable at a convenient loca tion with cable clamp. • When the cable is led in through the tran som board, make a hole of approx . 17 mm in diameter to pass the conne ctor . After passing the cable, fi ll the hole with a sealing comp ...

  • Furuno DFF3 - page 18

    1. MOUNTING 11 1.5.2 Thru-hull temperature sensor T-02MSB, T-03MSB Select a s uitable mounting l ocation consi dering the f ollowing poin ts: • Select a mi d-boat flat po sition. The sen sor does not have to be i nstalled perfe ctly perpendi cular. However, the loc ation shoul d not be such that the trans ducer may be damaged when the boat is dry ...

  • Furuno DFF3 - page 19

    12 2. WIRING 2.1 Wiring O utline Connect the power cable, transducer cables, sensor cable, network cabl e and ground wire to their respective locations on the n etwork sounder. See the next page for how to connect t he transducer cables. Grou nd Connect a gr ound wire (IV-2 s q, local sup ply) between the ground termi nal and ship’s ground to pre ...

  • Furuno DFF3 - page 20

    2. WIRING 13 2.2 Trans ducer Cable TD-ID transd uc er (Air mar make transd uc er) The TD-ID type tr ansducer can be connected to t h i s equipment. However, note th e following lim- itations : • TD-ID transducer cannot be used with NavNet , NavNet vx2. • TD-ID tr ansducer cannot be used with non- TD-ID transducer. • Connect single TD-ID trans ...

  • Furuno DFF3 - page 21

    2. WIRING 14 4. Connect the transducer cable to t he WAGO connector, followi ng the inst ructions in the figure below and the inter connec tion dia gram. ( The opener fo r the WAGO connector i s attached in- side the equipment . See the fi gure above.) 5. Unfasten the two screws lab eled Scr ew A in the figure below. 6. Loosen the two screws labele ...

  • Furuno DFF3 - page 22

    15 3. INITIAL SETTINGS 3.1 Tap Se tting This equipment is preprogr ammed for use with certai n transducers. A jumper wire i nside the equipment is set acco rding to transdu cer model. Check the jumper wire setting i nstructions on the sticker att ached to the chassis. Use the opener attached ins ide the unit to set the jumper wire. One end of the j ...

  • Furuno DFF3 - page 23

    3. INITIAL SE TTINGS 16 3.2 DIP Switch Setting The DIP switch S2 sets up th e system accordi ng to the equipment connected. I n the default setting all switche s (1-8) are OFF. The DIP swit ch S3 should not be adjusted; leave al l swi tches in the OFF positi on. DIP switch S2 descripti on *1: Power sync setting enabled at NavNet 3D. Switch No. Fu n ...

  • Furuno DFF3 - page 24

    3. IN ITIA L SETT INGS 17 DIP SW S2 sett ing, so under a nd IP a ddress Transduce r setting at NavNet/Na vNet3D After setting up the tr ansducer at the DFF3, set transduc er type at NavNet, NavNet 3D. See re- spective I nstallation Manual for the proc edure. SW No.3 SW No.4 SW No.5 SW No.6 Host Nam e IP Address OFF OFF OFF OFF S OUNDER 172.0 31.092 ...

  • Furuno DFF3 - page 25

    3. INITIAL SE TTINGS 18 3.3 Ope ra tio n Check For NavNet, the DFF3 is powered on/of f from ship ’s switc hboard. For NavNet 3D, it i s powered on/off f rom the displ ay unit. The LED on the c over of t he DFF3 lig hts or bl inks accor ding t o e quip- ment state, as descri bed i n the table below. LED state and meaning LED sta te Meani ng Lighti ...

  • Furuno DFF3 - page 26

    19 4. MAINTENANCE 4.1 Ma inten ance Regular maintenanc e is essential f or good performance. Check the items li sted in the table below at th e suggested interval to help k eep your equipment in good sh ape for years to come. Item Check po int, acti on Check i nterval Transd ucer cables Check th at cables are t ightly fast ened and are not damaged. ...

  • Furuno DFF3 - page 27

    4. MAINTENANC E 20 4.2 Rep lacin g the Fuse The 5A fuse ( Type: FGBO-A 125V 5A PBF, Code No. 000-155-85 3-10) in the snap-in fuse hol der on the power cabl e protects th e equipment from equipment f ault and rever se polarity of t he ship's mains. If the equipment cannot be powered, the fuse may h ave blown. Find out the cause for blown fuse b ...

  • Furuno DFF3 - page 28

    ＰＡＣＫＩＮＧ　ＬＩＳＴ 02GF-X-9851 -0 DFF3-J/E N A M E O U T L I N E DESCRIPTION/CODE № Q'TY 1/1 ユニット U NIT ﾈｯﾄﾜｰｸ魚探 NETWORK SOUNDER DFF3 000-0 11-9 16-00 1 予備品 SPARE PARTS SP02-05601 ﾋｭｰｽﾞ FUSE GLASS TUBE TYPE FGB0-A 125V 5A PBF 000-1 55-8 53-10 2 工事材料 INSTALLATION MATERIALS CP02 ...

  • Furuno DFF3 - page 29

    FURUNO DFF3 SP - 1 E2 037S01A 080318 SPECIFICA TIONS OF NETWORK SOUNDER DFF3 1 GENE RAL 1.1 T X frequency 28-200 kHz, two frequencies alternatel y transmitted (selectable) 1.2 Output powe r 1/2/3 kW nominal 1.3 Amplifier t ype Wide dynamic range linear amplifier (double superheterodyne) 1.4 Depth range and Pulse repetition ra te (PRR) 200 kHz, TX r ...

  • Furuno DFF3 - page 30

    Jan.18'08 R.Esumi D-1 ...

  • Furuno DFF3 - page 31

    2 4 3 A 1 B C DRAWN CHECKED APPROVED DWG.No. TITLE NAME 名称 INTERCONNE CTION DIAG RAM 相互結線図 REF.No. SCALE MASS kg C2037-C01- A T.YAMASAKI DFF3 ネットワーク魚探 NETWORK SOUN DER 02-161-1001-0 T.TAKENO NOTE *1: SHIPYARD SUPPLY. *2: OPTION. 注記 ＊１）造船所手配。 ＊２）オプション。 1 2 3 (+) (-) SHIELD WHT BLK ...

  • Furuno DFF3 - page 32

    The paper used in this manual is elemental chlorine free. ・FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN Telephone : +81-(0)798-65-2111 Fax : +81-(0)798-65-4200 A : MAR 2008 . Printed in Japan All rights reserved. Pub. No. OME-20370-A *00016858210* *00016858210* ( DAMI ) DFF3 * 00016858210 * * 00016858210 * ...

Manufacturer Furuno Category Radar Detector

Documents that we receive from a manufacturer of a Furuno DFF3 can be divided into several groups. They are, among others:
- Furuno technical drawings
- DFF3 manuals
- Furuno product data sheets
- information booklets
- or energy labels Furuno DFF3
All of them are important, but the most important information from the point of view of use of the device are in the user manual Furuno DFF3.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Furuno DFF3, service manual, brief instructions and user manuals Furuno DFF3. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Furuno DFF3.

Similar manuals

A complete manual for the device Furuno DFF3, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Furuno DFF3 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Furuno DFF3.

A complete Furuno manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Furuno DFF3 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Furuno DFF3, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Furuno DFF3, that we can find in the current document
3. Tips how to use the basic functions of the device Furuno DFF3 - which should help us in our first steps of using Furuno DFF3
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Furuno DFF3
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Furuno DFF3 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Furuno DFF3?

Use the form below

If you did not solve your problem by using a manual Furuno DFF3, ask a question using the form below. If a user had a similar problem with Furuno DFF3 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)