English dropdown-ico

Manual NEC 5800/320Fd

26 pages 1.84 mb
Download

Go to site of 26

Summary
  • NEC 5800/320Fd - page 1

    R e a d M e F i r s t : U n p a c k i n g E x p r e s s 5 8 0 0 / 3 2 0 F d S y s t e m C a b i n e t s NEC Cor poration of Americ a 456-017 4 1-000 ...

  • NEC 5800/320Fd - page 2

    Notice The information contained in this document is subject to change without not ice . UNLESS EXPRESSL Y SET FOR TH IN A WRITTEN A GREEMENT SIGNED BY AN A UTHORIZED REPRESENT A TIVE OF NEC, NEC MAKES NO W ARRANTY OR REPRESENT A TION OF ANY KIND WITH RESPECT T O THE INFORMA TION CONT AINED HEREIN, INCLUDING WARRANTY OF MERCHANT ABILITY AND FITNESS ...

  • NEC 5800/320Fd - page 3

    -iii- Contents Introduction 1 Packaged Cabinet 1 Before Unpacking the Cab inet 3 Moving the Cabinet t o the Installat ion Site 6 Unpacking and Checking the Cabinet 7 Tools Needed to Un pack the Cabinet 8 Removing the Pac king Materials 8 Removing the Cabinet f rom the Pallet 15 Checking the Cabinet and System s 17 Verifying the Express5 800/320 F d ...

  • NEC 5800/320Fd - page 4

    -iv- ...

  • NEC 5800/320Fd - page 5

    -1- Intr oduction Read Me First: Unpa cking Express5800/320 F d Cab inets describes ho w to move cabi nets that cont ain these systems to an installation site and how to u npack them. Warnings, cautions, and no tes in this document convey the following special information: W ARNING ! A warning indicates a situ ation where failure to take or avoid a ...

  • NEC 5800/320Fd - page 6

    -2- Figure 1. Cabinet P ac kaged f or Shipping The cardboard shipp ing container is secured t o a shipping pallet by exterior shipp ing straps. (Inside the sh ipping contain er, interior shipping straps secure the cabinet to the pallet.) A ramp for rolling the cabinet off the pallet is attach ed to one side of the shipp ing container, at th e rear ...

  • NEC 5800/320Fd - page 7

    -3- Bef ore Unpac king the Cabinet 1. Check the packing list to verify tha t y ou hav e received the correct shipment. 2. Verify th at the Tip-N-T ell and Shoc kwatch ha ndling indicators on the outside of the sh ipping container have not been activated. CA UTION ! If y ou receiv ed t he wrong shipme nt or a handlin g indicator has been activ ated, ...

  • NEC 5800/320Fd - page 8

    -4- Figure 2. Dimensions of a Pac kaged 38U Cabinet 80 in. (2m) 41 in. (104.14 cm) 53 in. (134.62 cm) 5 in. (12.7 cm) 38U Cabinet hsys033 ...

  • NEC 5800/320Fd - page 9

    -5- Figure 3. Dimensions of a Pac kaged 24U Cabinet Figure 4. Clearances Requir ed at the Installation Site 56.5 in. (1.435m) 41 in. (104.14 cm) 53 in. (134.62 cm) 5 in. (12.7 cm) 24U Cabinet hsys034 Cabinet on Pallet Pallet Ramp Unload From This End 42 in. (107 cm) 42 in. (107 cm) 150 in. (381 cm) 42 in. (107 cm) ...

  • NEC 5800/320Fd - page 10

    -6- If the corr idor and door dimensions are lar ge enough to accommodate the unpacked cabinet still tied to its pallet, use a pallet jack to m ove it from the delivery site to the installation site, as described in “Mo ving the Cab inet to the Installation Site” on page 6 . If the corridor and door dim ensions are too small to accommodate the ...

  • NEC 5800/320Fd - page 11

    -7- present, see the section “Stabilizing the Systems” on page 19 f or stabilization guidelines . When shipped, the syst em cabinet is tied to the pallet beneat h it. The pallet has a clear ance f or a pallet jac k to mo v e the unit. Wh en moving a system cabinet, fo llow these guidelines: 1. V er ify that the unpac k ed cabine t is still secu ...

  • NEC 5800/320Fd - page 12

    -8- T ools Needed to Unpack the Cabinet Use the following tools to unpack t he cabinet: • Metal shears to cut pallet straps • P air of scissors or utility knife • One 3/8-inch driv e ratchet wit h a 9/16-inch soc ket Remo ving the P ac king Materials W ARNING ! T o avoid per sonal injury or damage to the systems or cab inet, tw o persons are ...

  • NEC 5800/320Fd - page 13

    -9- Figure 5. Cutting t he Exterior Shipping Straps 3. Remove the ramp. The ramp is in two pieces that are held together b y a bolt. Unbolt the tw o pieces. Behind the ra mp is an accessor y box, which contain s v arious co mponents and documentation. Remo v e the bo x and set it aside f or later use. 4. Constr uct the ramp by inser tin g the be v ...

  • NEC 5800/320Fd - page 14

    -10- Figure 6. Remo ving the Packing Material 6. Remov e the plastic wrap encasing the cabinet . CA UTION ! If condensation e xists inside th e plastic wrap , you must provide a stabiliz ation period f or the systems. “Stabilizing the Syst ems” on page 19 hsys036 ...

  • NEC 5800/320Fd - page 15

    -11- provides comp lete inf ormation about the stabilization process. 7. Use the stra p buc kles to loosen the interior shipping straps that secure the cabinet to the pallet. See Figure 7 . Figure 7. Remo ving the Interior Shipping Straps 8. Remove the two fibe r protective slee v es at the to p-front and top-rear of the cabinet. 9. Loosen, but do ...

  • NEC 5800/320Fd - page 16

    -12- Figure 8. W ooden -R estraint Bloc ks 10. Loosen and remo v e the bolt s that secure t he wooden-r estraint bl ock at the front d oor of the cabinet . Then, remo v e the b loc k. 11. Locate the le v er bar . Inser t it in the cent er slot of one of th e sides. Se e Figure 9 . hsys038 ...

  • NEC 5800/320Fd - page 17

    -13- Figure 9. Inser ting the Lever Bar 12. With the assistan ce of another person, tilt th e cabinet from one side . As one person stands to br ace the cabi net near the top , a se cond person kn eels on the flo or and uses bot h arms to push do wn on the le v er bar , f orcing the cabinet to tilt. See Figure 10 . hsys039 ...

  • NEC 5800/320Fd - page 18

    -14- Figure 10. Til ting the Cabinet 13. After the cabinet is tilted, the person who has been stand ing must kneel on th e floor to slide the wooden restraint b loc ks aw a y from the cabi net. See Figure 11 . msys101 ...

  • NEC 5800/320Fd - page 19

    -15- Figure 11. Slidin g Bac k th e W ooden Restraint Bloc ks 14. Mov e the le ver bar to t he opposite side of the cabinet. Repe at the process of tilting th e cabinet and sliding bac k the two wooden rest raint b loc ks on the opposite sid e of the cabinet. Remo ving the Cabinet from the P allet 1. P osition the pallet ramp unde r the pallet, at ...

  • NEC 5800/320Fd - page 20

    -16- Figure 12. P osition the P allet Ramp 2. With the help o f another person , slowly and carefully roll the cabinet do wn the ramp , with one person on each side of the cabinet, not in the front or back. See Figure 13 . Each person must hold the upp er por tion of the cabin et with both hands . W ARNING ! The cabinet is top heavy . Use extre me ...

  • NEC 5800/320Fd - page 21

    -17- Figure 13. Moving the Ca binet Down the Pallet Ramp 3. Chec k the cabine t and systems f or da mage, as th e ne xt section describes. Checking the Cabi net and Systems Check the cabinet, systems , and optional compo nents for damage: 1. Open t he rear do or of the cabinet. F rom t he bottom of the cabinet, remove and discard the desiccant bag ...

  • NEC 5800/320Fd - page 22

    -18- V erifying the Express5800/320 F d Serial Number Find the equipment l abel to check the Express 5800/320 F d serial number. To find th e equipment label, open th e rear door of the cabinet. The equipment l abel is attached to the rear of each system. Check that the Ex press5800/320 F d serial number (n ot the Sol ect ron ® serial n umber) on ...

  • NEC 5800/320Fd - page 23

    -19- Stabilizing the Systems If temperature an d humidity changes have been extre me during transit, the cabinet and systems might deve lop condensation. Therefore, before you install an d power on the syst ems, you must inspect them and the cabinet f or condensation a nd, if necessary, stabilize the systems. To stabiliz e the systems, let the cabi ...

  • NEC 5800/320Fd - page 24

    -20- 4. Continue the insta llation, and continue to inspect for signs of condensation. If cond ensation appears , allo w additional stabilization periods unt il there are no sign s of condensation. CA UTION ! Bef ore y ou pow er on the systems, ve rify that the installation site envir onment meets the requirements specif ied in the Express5800/320 ...

  • NEC 5800/320Fd - page 25

    -21- To gain access to the document s on the World Wide Web, point your browse r to: http://supp ort .necam.com/ser vers/ Getting Help If you have a technical qu estion about Express5800/320 F d hardware or software, try these online resources first: • Online support from NEC T echnical Support. Yo u can find the latest techni cal inf ormation ab ...

  • NEC 5800/320Fd - page 26

    -22- ...

Manufacturer NEC Category Server

Documents that we receive from a manufacturer of a NEC 5800/320Fd can be divided into several groups. They are, among others:
- NEC technical drawings
- 5800/320Fd manuals
- NEC product data sheets
- information booklets
- or energy labels NEC 5800/320Fd
All of them are important, but the most important information from the point of view of use of the device are in the user manual NEC 5800/320Fd.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals NEC 5800/320Fd, service manual, brief instructions and user manuals NEC 5800/320Fd. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product NEC 5800/320Fd.

Similar manuals

A complete manual for the device NEC 5800/320Fd, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use NEC 5800/320Fd by users. Manuals are usually written by a technical writer, but in a language understandable to all users of NEC 5800/320Fd.

A complete NEC manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual NEC 5800/320Fd - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the NEC 5800/320Fd, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the NEC 5800/320Fd, that we can find in the current document
3. Tips how to use the basic functions of the device NEC 5800/320Fd - which should help us in our first steps of using NEC 5800/320Fd
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with NEC 5800/320Fd
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of NEC 5800/320Fd in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning NEC 5800/320Fd?

Use the form below

If you did not solve your problem by using a manual NEC 5800/320Fd, ask a question using the form below. If a user had a similar problem with NEC 5800/320Fd it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)