English dropdown-ico

Manual Icom IC-F110

24 pages 0.79 mb
Download

Go to site of 24

Summary
  • Icom IC-F110 - page 1

    iF110 VHF TRANSCEIVER INSTRUCTION MANUAL iF210 UHF TRANSCEIVER IC-F110_F210_GEN.qxd 02.12.11 4:25 PM Page a (1,1) ...

  • Icom IC-F110 - page 2

    i IMPOR T ANT EXPLICIT DEFINITIONS R W ARNING! NEVER connect the transceiver to an AC outlet. This may pose a fire hazard or result in an electric shock. NEVER connect the transceiver to a power source of more than 16 V DC such as a 24 V battery . This connection will ruin the transceiver . NEVER cut the DC power cable between the DC plug and fuse ...

  • Icom IC-F110 - page 3

    ii DO NOT use or place the transceiver in areas with tem- peratures below –30°C (–22°F) or above +60°C (+140°F), or in areas subject to direct sunlight, such as the dashboard. A VOID operating the transceiver without running the vehi- cle’s engine. The vehicle’s battery will quickly run out if the transceiver transmits while the vehicle ...

  • Icom IC-F110 - page 4

    1 1 P ANEL DESCRIPTION y t r q w e ■ Front panel q AF VOLUME CONTROL KNOB Rotate the knob to adjust the audio output level. • Minimum audio level is pre-programmed. w FUNCTION DISPLA Y Displays a variety of information, such as an operating channel number/name, 5-tone code, DTMF numbers and audible condition, etc. NOTE: The above functions depe ...

  • Icom IC-F110 - page 5

    2 1 P ANEL DESCRIPTION t DEALER-PROGRAMMABLE KEYS [P0] to [P3] Desired functions can be programmed independently by your dealer . y MICROPHONE CONNECTOR Connect the supplied microphone or optional DTMF micro- phone for SmarT runk II TM operation here. NEVER connect non-specified microphones. The pin assignments may be different and the transceiver ...

  • Icom IC-F110 - page 6

    3 1 P ANEL DESCRIPTION u 2/5TONE INDICA TOR Appears when the specified 2/5-tone call is received. i ALPHANUMERIC DISPLA Y Displays the CH number , 5-tone indication, DTMF num- bers, Audible indication, etc. NOTE: When the alphanumeric display blinks and trans- mitting becomes impossible, check that the DC battery voltage has not dropped below 8 V ...

  • Icom IC-F110 - page 7

    4 1 P ANEL DESCRIPTION ¡ ¡ SCAN ST ART/ST OP KEY Push this key to start scanning; and push again to stop. NOTE: Place the microphone on hook to start scanning. T ake the microphone off hook to stop scanning. ¡ ¡ SCAN T AG KEY Adds or deletes the selected channel to the scan group. ¡ ¡ PRIORITY CHANNEL KEYS Push these keys to select priority A ...

  • Icom IC-F110 - page 8

    5 1 P ANEL DESCRIPTION ¡ ¡ OUTPUT POWER SELECTION KEYS Select the transmit output power temporarily , or permanently , depending on the pre-setting. • Contact your dealer for the output power level for each selection. ¡ ¡ T ALK AROUND KEY T urns the talk around function ON and OFF . • The talk around function equalizes the transmit fre- que ...

  • Icom IC-F110 - page 9

    6 1 P ANEL DESCRIPTION ¡ ¡ SCRAMBLER KEY ➥ Push and hold to turn the voice scrambler func- tion ON. ➥ Push this key to turn the voice scrambler func- tion OFF . NOTE: • The optional UT -109 (#02) or UT -1 10 (#02) VOICE SCRAMBLER UNIT is required. – UT -109: Non-rolling type. 32 codes are available. – UT -1 10: Rolling type. Provides hi ...

  • Icom IC-F110 - page 10

    7 2 OPERA TION ■ T urning power ON q Push [ ] to turn the power ON. w If the transceiver is programmed for a start up passcode, input the digit codes as directed by your dealer . • The keys in the table below can be used for password input: • The transceiver detects numbers in the same block as identical. Therefore “01234” and “56789” ...

  • Icom IC-F110 - page 11

    8 2 OPERA TION ■ Receiving and transmitting RECEIVING: q Push [ ] to turn the power ON. w Push [] and [] to select a channel. e When receiving a call, adjust the audio output level to a comfortable listening level. TRANSMITTING: r T ake the microphone off hook. • 2-tone, 5-tone mute may be released. (The ‘audible’ condition is selected and ...

  • Icom IC-F110 - page 12

    9 2 OPERA TION D TX code channel selection If the transceiver has a [TX CH] key , the display can be tog- gled between the operating channel number (or name) and TX code channel number (or name). When the TX code channel number (or name) is displayed, the [] / [] keys select the TX code channel. T o select a TX channel: q Push [TX CH] —a TX code ...

  • Icom IC-F110 - page 13

    10 2 OPERA TION D User set mode User set mode is accessed at power ON and allows you to set seldom-changed settings. In this case you can “cus - tomize” transceiver operation to suit your preferences and operating style. Entering the user set mode: q While pushing and holding [] and [] , push [P OWE R] to enter user set mode ON, allowing you to ...

  • Icom IC-F110 - page 14

    11 3 OPTIONAL SmarT runk II ™ OPERA TION ■ SmarT runk II ™ and conventional modes This transceiver is capable of SmarT runk II™ functions. The optional UT -105 allows communication in conventional channels or SmarT runk II™ channels. Select a channel bank for SmarT runk II™ before trunking operation. • Push [ BANK ] several times to s ...

  • Icom IC-F110 - page 15

    12 3 OPTIONAL SmarT runk II™ OPERA TION D T erminating a call After completing a call, push [#] to disconnect (hang up). IMPORT ANT!: If one person in the conversation termi- nates a call, all participants will be cut off. D Last number re-dial Push [ M ] 2 times to automatically re-dial the last called num- ber . • A high-pitched beep indicate ...

  • Icom IC-F110 - page 16

    13 4 CONNECTION AND MAINTENANCE Optional speaker (SP-22) Optional cable (OPC-617) Antenna NEVER connect to a 24 V battery . + red: black: 12V Battery Solder Crimp NOTE: Use the terminals as shown below for the cable connections. R CAUTION! NEVER re - move the fuse-holder from the DC power cable. e r t w q ■ Rear panel and connection IC-F110_F210_ ...

  • Icom IC-F110 - page 17

    14 4 CONNECTION AND MAINTENANCE q ANTENNA CONNECTOR Connects to an antenna. Contact your dealer about an- tenna selection and placement. w MICROPHONE HANGER Connect the supplied microphone hanger to the vehicle ’ s ground for microphone on/off hook functions. (See p. 2) e DC POWER RECEPT ACLE Connects to a 12 V DC battery . Pay attention to polar ...

  • Icom IC-F110 - page 18

    15 4 CONNECTION AND MAINTENANCE ■ Mounting the transceiver The universal mounting bracket supplied with your transceiv- er allows overhead mounting. • Mount the transceiver securely with the 4 supplied screws to a thick surface which can support more than 1.5 kg. Flat washer Spring washer When using self-tapping screws ■ Optional UT -105, UT ...

  • Icom IC-F110 - page 19

    16 4 CONNECTION AND MAINTENANCE ■ Optional UT -109 or UT -1 10 installation q T urn the power OFF , then disconnect the DC power cable. w Unscrew the 4 cover screws, then remove the bottom cover . e Cut the pattern on the PCB at the TX mic circuit (MIC) and RX AF circuit (DISC) as shown below . r Install the scrambler unit as described in the ins ...

  • Icom IC-F110 - page 20

    17 4 CONNECTION AND MAINTENANCE ■ Antenna A key element in the performance of any communication sys- tem is an antenna. Contact your dealer about antennas and the best places to mount them. ■ Fuse replacement A fuse is installed in the supplied DC power cable. If a fuse blows or the transceiver stops functioning, track down the source of the pr ...

  • Icom IC-F110 - page 21

    18 5 OPTIONS SP-22 EXTERNAL SPEAKER Compact and easy-to-install. Input impedance : 4 Ω Max. input power : 5 W HM-100TN DTMF microphone. SM-25 Desktop microphone. UT -105 SmarT runk II TM Logic Board Provides SmarT runk II TM capabilities. UT -108 DTMF DECODER UNIT Provides pager and code squelch capabilities. UT -109/UT -1 10 (#02) VOICE SCRAMBLE ...

  • Icom IC-F110 - page 22

    MEMO IC-F110_F210_GEN.qxd 02.12.11 4:25 PM Page 19 (1,1) ...

  • Icom IC-F110 - page 23

    MEMO IC-F110_F210_GEN.qxd 02.12.11 4:25 PM Page 20 (1,1) ...

  • Icom IC-F110 - page 24

    Count on us! 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003 Japan A-6233H-1EX Printed in Japan © 2002 Icom Inc. IC-F110_F210_GEN.qxd 02.12.11 4:25 PM Page Z (1,1) ...

Manufacturer Icom Category Marine Radio

Documents that we receive from a manufacturer of a Icom IC-F110 can be divided into several groups. They are, among others:
- Icom technical drawings
- IC-F110 manuals
- Icom product data sheets
- information booklets
- or energy labels Icom IC-F110
All of them are important, but the most important information from the point of view of use of the device are in the user manual Icom IC-F110.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Icom IC-F110, service manual, brief instructions and user manuals Icom IC-F110. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Icom IC-F110.

Similar manuals

A complete manual for the device Icom IC-F110, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Icom IC-F110 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Icom IC-F110.

A complete Icom manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Icom IC-F110 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Icom IC-F110, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Icom IC-F110, that we can find in the current document
3. Tips how to use the basic functions of the device Icom IC-F110 - which should help us in our first steps of using Icom IC-F110
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Icom IC-F110
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Icom IC-F110 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Icom IC-F110?

Use the form below

If you did not solve your problem by using a manual Icom IC-F110, ask a question using the form below. If a user had a similar problem with Icom IC-F110 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)