English dropdown-ico

Manual Ariens 921012

44 pages 13.72 mb
Download

Go to site of 44

Summary
  • Ariens 921012 - page 1

    Owner/Operator Man ual Models 92101 1 – Deluxe 24 921012 – Delu xe 27 921013 – Delu xe 30 921014 – Delu xe T rack 2 4 921015 – Delu xe T rack 2 7 921016 – Delu xe T rack 3 0 921017 – Delu xe 24 Plati num 921018 – Delu xe 30 Plati num 921019 – Delu xe 24 921020 – Delu xe 30 Sno-Thro ® 03882700G 2/10 Printed in USA ENGLISH FRANÇ ...

  • Ariens 921012 - page 2

    GB - 2 SAFET Y . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ASS EMBL Y . . . . . . . . . . . . . . . . . . . . . . . 8 CONTROLS and FEA TURES . . . . . . . . 13 OPERA TION . . . . . . . . . . . . . . . . . . . . . 16 MAINTENANCE . . . . . . . . . . . . . . . . . . 23 SERVICE AND ADJUSTMENTS . . . . . 26 STORAGE . . . . . . . . . . . . . . ...

  • Ariens 921012 - page 3

    GB - 3 • Record Unit M odel and Serial numbers here. • Record Engine Model and Serial numbers here. PRODUCT REGISTRATION The Ariens d ealer must register the product at the time of purchas e. Registering the product will help the company process warranty claims or contact you with the latest service information. All c laims meeting requirements ...

  • Ariens 921012 - page 4

    GB - 4 SAFETY ALERT S Look for these s ymbols to point out important safety precautions. They mean: Attention! Personal Sa fety Is Invo lved! Become Alert! Obey T he Messag e! The safety alert symbols above an d signal words below are used on decals and in this manual. Read and understand all safet y messages. NOT ATIONS NOTE: General referenc e in ...

  • Ariens 921012 - page 5

    GB - 5 1. W ARNING! 2. DANGER! 3. DANGER! SAFETY RULES Read, understand, and follow al l safety practices in Owner/Operator Manual before beginning assembly or operating. Failure to follow instructions could result in personal injury and/or d amage to unit. AL W A YS remove key and/or wire from spark plug before assembly , maintenance or service. U ...

  • Ariens 921012 - page 6

    GB - 6 DO NOT operate near drop-offs, di tches, or embankments. Unit can s uddenly turn over if a wheel is over the edge of a cliff or ditch, or if an edge caves in. Falling snow , fog, etc. can reduce vision and cause an accident . Operate unit only when there is good visibility and light. NEVER operate unit after or during the use of medication, ...

  • Ariens 921012 - page 7

    GB - 7 Check clutch and brake operation frequently . Adjust and service as required. All motion of drive wheels and auger/impeller must stop quickly when cont rol levers are released. DO NOT operate on steep slopes. DO NOT clear snow across the fa ce of slopes. Keep all movement on slopes slow and gradual. DO NOT make s udden changes in s peed or d ...

  • Ariens 921012 - page 8

    GB - 8 PACKAGE CONTENTS ASSEMBLY T ools Required: •P l i e r s • Open-End Wrenches: 3/8, 7/16, 1/2, 9/16 in. and/or Adjustable Wr ench • Ti re Gauge ASSEMBL Y W ARNING: A VOID INJURY . Read and understand the entire Safety section before procee ding. W ARNING: Dropping or tipping over boxed unit could result in personal injury or damage to un ...

  • Ariens 921012 - page 9

    GB - 9 Unfold Handle bar (Figure 5) 1. Re move the lower and loosen the upper hardware on t he handlebar assem bly . 2. Loosen the hardware on the shift rod. 3. Put the speed selector lever in the second reverse position. (Fastest forward position for 92101 1, 014, 019). 4. R ot ate the h andlebars into operating position. IMPORT ANT : Be careful n ...

  • Ariens 921012 - page 10

    GB - 10 Inst all Dis charge Chu te and Discharge Chute Rod (921017, 018) (Figure 8, 9 , 10 and 1 1) 1. Gre ase underside of discharge chute ring (if not already greased). 2. R emove mounting hardware from auger housing. 3. Install discharge c hute over opening in the auger housing. Finger tighten the mounting hardware removed in step 2. NOTE: Leave ...

  • Ariens 921012 - page 11

    GB - 11 9. Connect the chute lock cable t o the lock arm by fitting the cable ball end into the slot on the lock arm and then insert the chute lock cable fitting into the bracket on the chute pedest al (Figure 1 1). 10. Adjust and tighten jam nut s on cable to remove cable s lack. Be s ure not to pretension lock arm so it retracts from the gear tee ...

  • Ariens 921012 - page 12

    GB - 12 Check Function of Dual Handle Interlock Without the engine running, pres s down (engage) both clutch levers. Release attachment clutch lever . Attachment clutch should remain engaged until traction cl utch lever is released, the n both clutches must disengage. If they do not, cont act your Dealer for r epairs . Check T ire Pressure (92101 1 ...

  • Ariens 921012 - page 13

    GB - 13 1. Attachment Clutch Lever 2. S peed Selector 3. T raction Drive Clutch Lever 4. Remote Wheel Lock (012, 013, 020) 5. Deflector Remote Control (013 , 016, 017, 018, 020) 6. Height Adjuster Trigger (014, 015, 016) 7. Chute Rotation Control (017, 018) CONTROLS AND FEA TURES Figure 13 OS7440 5 2 3 1 6 OS7093 5 2 3 1 6 2 1 3 SMALL DASH LARGE DA ...

  • Ariens 921012 - page 14

    GB - 14 1. Skid Sho e 2. Clean-Out T ool 3. Remote Discharg e Chute Deflector (013, 016, 017, 018, 020) 4. Manual Discharge Chute Deflector (01 1, 012, 014, 019) 5. Belt Cover 6. Headlight (012, 013, 015, 016, 017, 018, 020) 7. Auger 8. Auger Gearc ase 9. Scraper Blade 10. Discharge Chute 1 1 . Impeller 12. Chute Crank (01 1, 012, 013, 014, 015, 01 ...

  • Ariens 921012 - page 15

    GB - 15 1. Oil Drain 2. Fuel Shut-Off V alve 3. Primer Bulb 4. Recoil S tarter Handle 5. Throttle (Engine St op) 6. Choke Control Knob 7. Ignition Key (Pus h/Pull) 8. Fuel T an k and Cap 9. Oil Fi ll/Dipstick Figure 1 5 OS7420 OS7415 OS7410 92101 1, 012, 013, 01 4, 015, 016, 017, 018 3 921019 , 020 1 5 7 2 4 4 4 8 8 9 9 9 3 5 6 2 4 1 6 7 ...

  • Ariens 921012 - page 16

    GB - 16 CONTROLS AND FEA TURES See CONTROLS and FEA TURES on page 13 for all Controls and F eatures locations. Dual Handle Interlock When Attachment Clutch and t hen T raction Drive Clutch are engaged, the Attachment Clutch will remain engaged (leve r down) if released. T o stop att achment, release T raction Drive Clutch and both clutches will dis ...

  • Ariens 921012 - page 17

    GB - 17 Primer Bulb Pushing the primer bulb in adds fuel for easier engine st art. Refer to St arting and Shut Off on page 22. S peed Selector (012, 013, 015 , 016, 017, 018, 020) Position the Speed Selector in the appropriate speed notch to control forward and reverse t ravel. Forwar d: (6) Fast est (1) Slowest Reverse: (1) Slow (2) Fast IMPORT AN ...

  • Ariens 921012 - page 18

    GB - 18 Snow Clean-Out T ool (Figure 16) T o clear the discharg e chute: 1. Shut off the engine. 2. Wait 10 seconds and make sure impeller blades have s topped rotating. 3. R emove the snow clean- out tool (1) from the auger housing and use it to remove the clog from the discharge chute. 4. Replace t he snow clean-out tool on the auger housing. Rem ...

  • Ariens 921012 - page 19

    GB - 19 IMPORT ANT : DO NOT force frozen chute controls. If f rozen, take to warm place until controls are free. Dis charg e Chut e Cran k (921 01 1, 01 2, 013, 014, 015, 016, 019, 020) IMPORT ANT : If chute does not s t ay in set position, adjust as directed in SERVICE AND ADJU STMEN TS on page 26 , or rep air before operation. Rotate the Chute wi ...

  • Ariens 921012 - page 20

    GB - 20 Skid Shoes The skid sho es control the distance between the scraper blade and the ground. Adjust skid shoes equally to keep blade level wit h the ground. Refer to Pre-St art on page 21 for recommended sett ings. T rack An gle (921014, 015, 016) (Figure 21) The track angle can be adjusted to position the auger housing for level clearing, dee ...

  • Ariens 921012 - page 21

    GB - 21 GASOLINE IMPORT ANT : AL W A YS use gasoline that meets the following guidel ines: • Clean, fresh gasoline. • A minimum o f 87 octane/87 AKI (91 RON). High altitude use may require a diff erent octane. Consult your engine manual. • Gasoline with up to 10% et hanol (gasohol) or up to 15% MT BE (methyl tertiary butyl ether) is acceptabl ...

  • Ariens 921012 - page 22

    GB - 22 ST ARTING AND SHUT OFF IMPORT ANT : Allow unit and engine to adjust to the outdoor t emperature before clearing snow . Before shut-off, run the attachment a few minutes to prevent impeller freeze-up. NOTE: Try out each control without the engine running to se e how it works and what it does. Manual S t art 1. Turn discharge chute s traight ...

  • Ariens 921012 - page 23

    GB - 23 SNOW R EMOVA L IMPORT ANT : Allow unit and engine to adjust to the outdoor t emperature before clearing snow . NOTE: Attachment clutch s hould be engaged before wheel drive clutch when throwing snow . 1. Select Speed Control position and direction. 2. Engage A ttachment Clutch - Right Hand Lever . 3. Engage T raction Drive Clutch - Le ft Ha ...

  • Ariens 921012 - page 24

    GB - 24 MAINTENANCE SCHE DULE The chart below shows the recommended maintenance schedule that should be performed on a regular basis. More frequent service may be required. * After first five hours of operation. ** After f irst two hours of operation, thereafter every 25 hours. CHECK DUAL HANDLE IN TERLO CK Without the engine running, pres s down ( ...

  • Ariens 921012 - page 25

    GB - 25 CHECK AUGER GEARCASE IMPORT ANT : Proper oil level must be maintained. Gear cases are filled to the correct level at the factory . Unless there is evidence of leakage, no additional lubricant should be required. Check oil level each season or every 25 hours of operation. T o ensure adequat e lubricant level: 1. R emove filler plug (F igure ...

  • Ariens 921012 - page 26

    GB - 26 SCRAPER BLADE IMPORT ANT : Damage to auger/impeller housing will result if blade wears down too far. Scraper blade is adjustable to compensate for wear . T o adjust scraper bla de: 1. Tip unit back onto handleb ar , support housing and loosen nuts ret aining blade. 2. Adjust skid shoes to fully raised position (housing closest t o ground). ...

  • Ariens 921012 - page 27

    GB - 27 6. Repeat steps 2 – 4 while watching cab le to remove slack. 7. C heck function of remote wheel lock. If wheel lock does not function properly , take the unit to Dealer for repairs. REMOTE DEFLECTOR CONTROL (9210 13, 016, 01 7, 018, 020) Deflector must stay in selected position while th rowi ng sn ow . If deflector does not stay in set po ...

  • Ariens 921012 - page 28

    GB - 28 If chute does not rot ate freely: T ighten the cable by loosening the forward adjustment nut, and then tightening the rear adjustment nut against the bracket unt il all cable slack is removed (Figure 31). DISCHARGE CHUTE MANUA L DEFLECTOR (92101 1, 012, 014, 015, 019) Deflector must stay in selected position while blowing snow . T o adjust, ...

  • Ariens 921012 - page 29

    GB - 29 d. S t op unit. e. Shift speed selector into first reverse speed. f. Engage the traction clutch. Unit should move back ward. g. Shut off unit. 8. Adjust pivot pin on the shift rod as necessary so unit travels fo rward when speed selector is in first forward position and travels backward when speed selector is in first reverse position. 9. C ...

  • Ariens 921012 - page 30

    GB - 30 • If roller is more that 7/8 i n. (22.2 mm) from frame, loosen idler adjustment nut and move idler away from the belt, tighten adjustment nut and recheck roller clearance. Adjust th e Atta chment Clutch Cable S pring Extension (Figure 38 a nd 39) 1. C heck the attachment clutch cable spring extension. Measure the length o f the attachment ...

  • Ariens 921012 - page 31

    GB - 31 Check At tach ment Brake (Figure 40) 1. With t he clutch lever disengaged, brake pad must contact a ttachment belt s. With clutch lever engaged, brake pad must be more than 1/16 in. (1.6 m m) from belts. If there is more than 1/16 in. (1.6 mm ) gap, go to Check Belt Finger Clearance on page 31. If there is less than 1/16 in. (1.6 mm ) gap, ...

  • Ariens 921012 - page 32

    GB - 32 4. T o adjust traction clutch (Figure 43): a. With the traction drive clutch lever disengaged, loosen the jam nut on the cable adjuster. b. Turn the adjuster body up the cable to decrease the distance between the clutch lever and handlebar . c. Turn the adjuster body dow n the cable to increase the distance between the clutch lever and hand ...

  • Ariens 921012 - page 33

    GB - 33 8. R emove hex bolts securing housing to frame (two on each side). Tip housing and frame apart on pivot pin (Figure 45). 9. R emove attachment drive belts from attachment pulley (hold brak e away from belt). Inst all new attac hment drive b elts : 1. Place new attachment belts onto attachment pulley . NOTE: Holding down the attachment clutc ...

  • Ariens 921012 - page 34

    GB - 34 3. Pull idler aw ay from traction drive belt and remove belt from idler pulley , engine sheave and driven pulley (it may be necessary to turn engine pulley using recoil handle). 4. Install new traction drive belt onto driven pulley and engine sheave. 5. Swing dr ive plate toward friction disc until finger lines up w ith stop hole in frame. ...

  • Ariens 921012 - page 35

    GB - 35 T RACK T E NSION ADJUSTMENT (9210 14, 015, 01 6) Check the track tension by applying pressure on the track mi dway between the upper and rear track rollers. Deflection should be approximately 3/8 in. (9.6 mm) (Figure 49). If deflection is exces sive, tighten the track tension. If unit pulls to the lef t or right when a straight path is desi ...

  • Ariens 921012 - page 36

    GB - 36 SHORT T ER M IMPORT ANT : NEVER spray unit with high pressure wa ter or store unit outdoors. Run with attachment clutch engag ed a few minutes after each use to free unit of any loose or melting snow . Close fuel shut-off valve. Inspect unit for v isible signs of wear , breakage or damag e. Keep all nuts, bolts and screws properly tightened ...

  • Ariens 921012 - page 37

    GB - 37 TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTION Engine wi ll not crank/ start. 1. Fuel t ank is empty . 2. Fuel shut-off valve closed. 3. Build up of dirt and residue around governor/carburetor . 4. Key Sw itch not in run position. 5. Electric starter not functioning. 1. Fill fuel tank. 2. Open fuel shut-off valve. 3. Clean area around go ...

  • Ariens 921012 - page 38

    GB - 38 SPECIFICA TIONS Mode l Numbe r 92101 1 921012 921013 Description Deluxe 24 Deluxe 27 Deluxe 30 Engi ne Engine Briggs & S tratton 1 150 Snow Series Brig g s & S tr atton 1450 Snow Series Gross T orque* - ft -lbs (N•m) 1 1. 5 (15.59) 14.5 (19.66) *Engine output stated in gross torque per SAE J1940 as rated by engine manufacturer Dis ...

  • Ariens 921012 - page 39

    GB - 39 SPECIFICA TIONS Model Num ber 921014 921015 921016 Description Deluxe T rack 24 Deluxe T rack 27 Deluxe T rack 30 Engine Engine Briggs & S tratton 1 150 Snow Series Briggs & S tratton 1450 Snow Series Gross T orque* - ft-lbs (N•m) 1 1. 5 (15.59) 14.5 (19.66) *Engine output stated in gross torque per SA E J1940 as rated by engine m ...

  • Ariens 921012 - page 40

    GB - 40 SPECIFICA TIONS Model Num ber 921017 921018 921019 921020 Description Deluxe 24 Platinum Deluxe 30 Platinum Deluxe 24 Deluxe 30 Engine Engine Model Briggs & S tratton 1 150 Snow Series Briggs & S tratton 1650 Snow Series Subaru SX21 Subaru SX30 Gross T or que* - ft-lbs (N•m) 1 1. 5 (15.59) 16.5 (22.37) TBD *Engine output stated in ...

  • Ariens 921012 - page 41

    ARIENS COMP ANY GRA VEL Y ® | STENS ® | LOCKE ® | NA TIONAL ® | BYN ORM ® | EVERRIDE ® | GREA T DANE ® Snow_200 8 Page 41 Three-Y ear Limited Sno-Thr o ® Wa r r a n t y Ariens Company (Ariens) warrants to the original purc haser that Ari ens Sno-Th ro products will be free from defects in mate rial and workmansh ip for a pe riod of thr ee y ...

  • Ariens 921012 - page 42

    ARIENS COMP ANY GRA VEL Y ® | STENS ® | LOCKE ® | NA TIONAL ® | BYN ORM ® | EVERRIDE ® | GREA T DANE ® Snow_200 8 Page 42 Limitations • Batteries are war ranted only f or a period of 12 month s after date of purchase, o n a prorat ed basis. For the first 90 da ys of the warranty p eriod, a defe ctive battery will be re placed free of charg ...

  • Ariens 921012 - page 43

    ...

  • Ariens 921012 - page 44

    Protective F loor Mat Protects oor from rust, dirt and snow melt. Ariens Co mpany 655 West Ryan S treet Brillion, WI 541 10-1072 920-756-2141 Fax 920-756-2407 www.arien s.co m ...

Manufacturer Ariens Category Snow Blower

Documents that we receive from a manufacturer of a Ariens 921012 can be divided into several groups. They are, among others:
- Ariens technical drawings
- 921012 manuals
- Ariens product data sheets
- information booklets
- or energy labels Ariens 921012
All of them are important, but the most important information from the point of view of use of the device are in the user manual Ariens 921012.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Ariens 921012, service manual, brief instructions and user manuals Ariens 921012. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Ariens 921012.

Similar manuals

A complete manual for the device Ariens 921012, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Ariens 921012 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Ariens 921012.

A complete Ariens manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Ariens 921012 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Ariens 921012, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Ariens 921012, that we can find in the current document
3. Tips how to use the basic functions of the device Ariens 921012 - which should help us in our first steps of using Ariens 921012
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Ariens 921012
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Ariens 921012 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Ariens 921012?

Use the form below

If you did not solve your problem by using a manual Ariens 921012, ask a question using the form below. If a user had a similar problem with Ariens 921012 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)