English dropdown-ico

Manual Packard Bell TM86

216 pages 16.37 mb
Download

Go to site of 216

Summary
  • Packard Bell TM86 - page 1

    Packard Bell EasyNote TM86/TM87/TM89 Series Service Guide PRINTED IN T AIW AN Service guide files and updates are availab le on the ACER/CSD web; for more information, please refer to http://csd.acer .com.tw ...

  • Packard Bell TM86 - page 2

    II Revision History Please refer to the table below for the updates ma de on Packard Bell EasyNote TM86/TM87/TM89 service guides. Date Chapter Up dates ...

  • Packard Bell TM86 - page 3

    III Copyright Copyright © 2010 by Acer Incorporated. All rights rese rved. No part of this pub lication may be reproduce d, transmitted, transcribed, stored in a retrieval system, or translated into a ny language or computer language, in any form or by any means, electronic, mechanical, magne tic, optical, chemi cal, manual or otherwise, without t ...

  • Packard Bell TM86 - page 4

    IV Conventions The following conventi ons are used in this manual: NOTE: This symbol where placed in the Ser vice Guide design ates a component that should be recycled according to the local regulation s. SCREEN MESSAGES Denotes actual messages that appear on screen. NOTE Gives bits and pieces of additional information related to the current topic. ...

  • Packard Bell TM86 - page 5

    V Preface Before using this information and the product it s upports, please read the fo llowing general informa tion. 1. This Service Guide provides you with all techni cal information relating to the BASIC CON FIGURA TION decided for Acer's "glo bal" product offering. T o better fit local market require ments and enhance product co ...

  • Packard Bell TM86 - page 6

    VI ...

  • Packard Bell TM86 - page 7

    VII T able of Contents System Specifications 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Your Acer Notebook tour . . . . . . . . . . . . . . . ...

  • Packard Bell TM86 - page 8

    VIII T able of Contents Removing the Card Reader Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Removing the USB Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74 Removing the Bluetooth Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Remov ...

  • Packard Bell TM86 - page 9

    IX T able of Contents TouchPad Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 Internal Speaker Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .144 HDD Not Operating C orrectly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Packard Bell TM86 - page 10

    X T able of Contents ...

  • Packard Bell TM86 - page 11

    Chapter 1 1 System Specifications Features Below is a brief summary of the computer ’s many features: NOTE: Items denoted with an (*) are only available for selected models. Operating System • Genuine Windows® 7 Home Premium 64-bit* • Genuine Windows® 7 Hom e Basic 64-bi t* Platform • Intel® Core i5-430M/i5-5 20M/i5-540M processor (3 MB ...

  • Packard Bell TM86 - page 12

    2 Chapter 1 • External resolution / refresh rate: • VGA port up to 2560 x 1600: 60 Hz • VGA port up to 2048 x 1536: 85 Hz • HDMI™ port up to 1920 x 1080: 60 Hz • MPEG-2/DVD decoding • WMV9 (VC-1) and H.264 (A VC) decoding • Microsoft® DirectX Video Acceleration (DXV A) application interface (API) • HDMI™ (High-Definition Multim ...

  • Packard Bell TM86 - page 13

    Chapter 1 3 • 802.1 1b/g/n Wi-Fi CERTIFIED™ • 802.1 1b/g Wi-Fi CERTIFIED™ •W P A N : • Bluet ooth® 2 .1 •L A N : • Gigabit Ethernet, Wake-on-LAN ready Privacy control • BIOS user , supervi sor , HDD passwords • Kensington lock slot Power subsystem • ACPI 3.0 CPU power manageme nt standard: supports S tandby and Hibernation po ...

  • Packard Bell TM86 - page 14

    4 Chapter 1 • Packard Bell Identity Card • Packard Bell InfoCentre • Packard Bell MyBackup Solution • Packard Bell Power Manage ment • Packard Bell Recovery Management • Packard Bell Registration • Packard Bell Social Networking Application • Packard Bell Updater • Adobe® Flash® Player 10 • Adobe® Photoshop® Elements 7 • A ...

  • Packard Bell TM86 - page 15

    Chapter 1 5 System Block Diagram ...

  • Packard Bell TM86 - page 16

    6 Chapter 1 Your Acer Notebook tour Front View No. Icon Item Description 1 Webcam Web camera fo r video communicati on (for selected models). 2 Microphone Internal microphone for recording sound. 3 Display screen Also called Liquid-Crystal Display (LCD), displays computer output. 4 HDD Indicates when the hard disk drive is active. Communication ind ...

  • Packard Bell TM86 - page 17

    Chapter 1 7 NOTE: 1 The front pa nel indicato rs are visible even when the comput er cover is closed. Closed Front View 5 Power button T urns the computer on and off. 6 Keyboard For entering data into your computer . 7 Palmrest Comfortable support area for your hands when you use the computer . 8 Click buttons (left and right) The left and right bu ...

  • Packard Bell TM86 - page 18

    8 Chapter 1 Left View No. Icon Item Description 1 DC-in jack Connects to an AC adapter 2 V enti lation slots Enable the computer to stay cool, even after prolonged use. 3 External display (VGA) port Connects to a display device (e.g. external moni tor , LCD projector). 4 Ethernet (RJ-4 5) port Connects to an Ethernet 10/100-based network. 5 HDMI Co ...

  • Packard Bell TM86 - page 19

    Chapter 1 9 Right View Bottom View No. Item Description 1 USB 2.0 ports Connect to USB 2.0 devices (e.g. USB mouse, USB camera). 2 Optical drive Internal optica l drive; accepts CDs or DVDs. 3 Optical disk access indicator Lights up when the optical drive is active. 4 Optical drive eject button Ejects the optical disk from the drive. 5 Emergency ej ...

  • Packard Bell TM86 - page 20

    10 Chapter 1 Indicators The computer has several easy-to-read status indicators . The front panel indicato rs are visible even when the computer cover is closed. No. Icon Item Description 1 Battery bay Houses the computer's battery pack. 2 Battery release latch Releases the battery for removal. 3 Hard disk bay Houses the computer's hard d ...

  • Packard Bell TM86 - page 21

    Chapter 1 11 TouchPad Basics The following items show you how to use the T ouchPa d: • Move your finger across the T ouchPad (1) to move th e cursor . • Press the left (2) and right (3) buttons located beneath the T ouchPad to perform selectio n and execution functions. These two buttons are simila r to the left and right buttons on a mouse. T ...

  • Packard Bell TM86 - page 22

    12 Chapter 1 Using the Keyboard The keyboard has ful l-sized keys an d an embedded numeric keyp ad, sep arate cursor , lock, Windows, function and special keys. Lock Keys and embedded numeric keypad The keyboard h as two lock keys which you can toggle on and off. Lock key Description Caps Lock When Caps Lock is on, all alphabetic characte rs typed ...

  • Packard Bell TM86 - page 23

    Chapter 1 13 Windows Keys The keyboard has two keys that perform Wi ndows-specific functions. Key Description Windows key Pressed alone, this key has the same ef fect as clicking on the Windows S tart button; it launches the S tart menu. It can also be used with other keys to provide a variety of functions: <> : Open or close th e S tart menu ...

  • Packard Bell TM86 - page 24

    14 Chapter 1 Hot Keys The computer employs hotkeys or key combinations to access most of the computer ’s controls like screen brightness, volume out put and the BIOS utility . T o activate hot keys, press and hold the < Fn> key before pressing the other key in the hotkey combination. Hotkey Icon Functi on Description <Fn> + <F2> ...

  • Packard Bell TM86 - page 25

    Chapter 1 15 Social Networking Opens Facebook Login screen. <Fn> + <Pg Up> Page Up Scrolls the page up. <Fn> + <Pg Dn> Page Down Scrolls the page down. <Fn> + <Home> Home Scrolls to the top of the page. <Fn> + <End> End Scrolls to the bottom of the page. Hotkey Icon Functi on Description ...

  • Packard Bell TM86 - page 26

    16 Chapter 1 Hardware Specifications and Configurations Processor Processor Specifications CPU Fan T rue V alue T able (Tj = 90) • Throttling 50%: On=85 °C, Off=72°C • OS Shutdown: 104°C • H/W Shutdown: 92°C CPU Fan T rue V alue T able (Tj = 105) • Throttling 50%: On=10 0°C, Off=85°C • OS Shutdown: 104°C • H/W Shutdown: 92°C BIO ...

  • Packard Bell TM86 - page 27

    Chapter 1 17 System Memory Memory Combinations NOTE: Above table lists some system memory configur ations. Y ou may combine DIMMs with various capacities to form other combinations. In the above ta ble, the configuration of slot 1 and slot 2 could be reversed. LAN Interface Features • F lash ROM 4MB • Support ISIPP • Support Acer UI • Suppo ...

  • Packard Bell TM86 - page 28

    18 Chapter 1 Onboard LAN Feature Support for 10/100/1000 Item Specification Manufacturer Broadcom 57780KMLG for GIGA LAN • Integrated 10 /100/10000BASE-T transceiver • Automatic MDI crossover function • PCIe V1.1 complian t • 10/100/10000BASE-T full - duplex/half - duplex MAC • Receive side scaling(RSS) for multicore processors • Compli ...

  • Packard Bell TM86 - page 29

    Chapter 1 19 Hard Disk Drive Interface Item Sp ecification V endor & Model Name Seagate HGST T oshiba W estern Digital Capacity (MB) 160, 250, 320, 500 160, 250, 320, 500 160, 250, 320, 500 160, 250, 320, 500, 640 Bytes per sector 512 Data heads 2-4 Drive Format Disks 1-2 S pind le speed (RPM) 5400 Performance S pecifications Buffer size 8 MB I ...

  • Packard Bell TM86 - page 30

    20 Chapter 1 Super-Multi Driv e Module Audio Interface Item Specification V endor & model name HLDS G T20N Sony AD7580S Performance S pecificat ion With CD Diskette With DVD Diskette With CD Diskette With DVD Diskette T ransfer rate (MB/ sec) Sustained: 3,600 KB/s (24x) max. Sustained: 1 1.08 Mbytes/s (8x) max. Sustained: 1,571 (typical) Sustai ...

  • Packard Bell TM86 - page 31

    Chapter 1 21 Power and Keyboard Controller Battery Features • High Definition Audio Codec • Single Analog ue MIC • 2.0 Watt speaker/5cc chamber/speaker size 18 phi, x2 • Headphone-out w/o SPDIF-out Item Specification Controller GP8T T ype; 358 .27mm x 1 13.44mm x 4.9mm Features • Support Windows keys and Applica tion keys • S tandard pi ...

  • Packard Bell TM86 - page 32

    22 Chapter 1 LCD 15.6” Card Reader Item Specification V endor/model name AUO/CPT/CMO/Samsung/LCD/INL Screen Diagonal (mm) 15.6 inches Display resolution (p ixels) 1366 x 768 WXGA Clare Pixel Pitch 0.204 x 0.204 Display Mode Normal T ypical White Lumin ance (cd/m 2 ) (also called Brightness) 220 Contrast Ratio 500 typical Response T ime (Optical R ...

  • Packard Bell TM86 - page 33

    Chapter 2 23 System Utilities BIOS Setup Utility The BIOS Setup Utility is a hardware configuration prog ram built into y our computer ’s BIOS (Basic Input/ Output System). Y our computer is al ready properly configured and optimi zed, and you do not need to run this utili ty . However , if you encounter configuration problems, you may need to ru ...

  • Packard Bell TM86 - page 34

    24 Chapter 2 Packard Bell EasyNote TM86/TM87/TM89 BIOS Information The Information screen displa ys a summary of the comput er hardware information. NOTE: The screen above is for your reference only . Actual values may differ according to model. The table below describes the parameters in this screen. Parameter Description CPU T ype This field show ...

  • Packard Bell TM86 - page 35

    Chapter 2 25 Main The Main screen allows th e user to set the system time and date as well as enable and disa ble boot options and recovery . NOTE: The screen above is for your reference only . Actual values may differ . The table below describes the parameters in this screen. Parameter Description Format/Option System T ime Sets the system time. T ...

  • Packard Bell TM86 - page 36

    26 Chapter 2 Display Mode Control the graphics display mode. Note: Switchable Graphics is displayed as an o ption if supported by the system. Options: Integra ted Graphics, Discrete Graphics or Sw itchable Graphics Parameter Description Format/Option ...

  • Packard Bell TM86 - page 37

    Chapter 2 27 Security The Security screen contains parameters that help sa feguard and protect your co mputer from unautho rized use. The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings. NOTE: When you are prompted to enter a p assword, you have three tries be fore the syste ...

  • Packard Bell TM86 - page 38

    28 Chapter 2 Setting a Password Follow these steps as you set the user or the supervisor password: 1. Use the ↑ and ↓ keys to highlight the Set Supe rvisor Password parameter and press the Enter key . The Set Supervisor Password box appears: 2. T ype a password in the “Enter New Password” fiel d. The password length can not exce ed 8 alphan ...

  • Packard Bell TM86 - page 39

    Chapter 2 29 Changing a Password 1. Use the ↑ and ↓ keys to highlight the Set Supe rvisor Password parameter and press the Enter key . The Set Password box appears. 2. T ype the current p assword in the Ent er Current Passw ord field an d press Enter . 3. T ype a password in the Enter New Password field. Retype the password in the Confirm New P ...

  • Packard Bell TM86 - page 40

    30 Chapter 2 Boot This menu allows the user to deci de the order of boot devi ces to load the operatin g system. Bootable devices includes the USB diskette drives, the onboard hard disk d rive and the DVD drive in the module ba y . Select Boot Devices to select specific devices to support boot. Item Specific Help Use < > or < > to selec ...

  • Packard Bell TM86 - page 41

    Chapter 2 31 Exit The Exit screen allows you to save or discard any changes you made an d qui t the BIOS Utility . The table below describes the parameters in this screen. Parameter Description Exit Saving Changes Exit System Setup and save your changes. Exit Discarding Changes Exit utility without saving setup data. Load Setup Default Load default ...

  • Packard Bell TM86 - page 42

    32 Chapter 2 BIOS Flash Utilities The BIOS Flash memory upd ate is required for th e following conditions: • New versions of system programs • New features or options • Restore a BIOS when it becomes corrupted. Use the Flash utility to update the system BIOS Fla sh ROM. NOTE: If you do not have a crisis recovery diskette at hand, then you sho ...

  • Packard Bell TM86 - page 43

    Chapter 2 33 DOS Flash Utility Perform the following steps to use the DOS Flash Utility: 1. Press F2 during boot to enter the Setup Men u. 2. Select Boot Menu to modify the boot priority order , for e xample , if using USB HDD to Upd ate BIOS, move USB HDD to position 1. 3. Execute the BIOS.BA T batch file to update BIOS. The flash process begins a ...

  • Packard Bell TM86 - page 44

    34 Chapter 2 4. In flash BI OS, the me ssage Please do not remove AC Power Source displays. NOTE: If the AC power is not connected, the following message displays. Plug in the AC power to continue. 5. Flash is complete when the message Flash programming complete disp lays. ...

  • Packard Bell TM86 - page 45

    Chapter 2 35 WinFlash Utility Perform the following steps to use the WinFlash Utility: 1. Double-click the WinFlash executable. 2. Click OK to begin the update. A progress screen displays. ...

  • Packard Bell TM86 - page 46

    36 Chapter 2 Remove HDD/BIOS Password Utilities This section provide s you with d e tails about removing HDD/BIOS password: Remove HDD Password: If you key in the wrong HDD password three times, an error is gen erated. T o reset the HDD p assword, perform the following steps: 1. After the error is displayed, select the Enter Unloc k Password option ...

  • Packard Bell TM86 - page 47

    Chapter 2 37 Removing BIOS Passw ords T o clear the User or Supervisor passwords, open the DIMM door and use a metal instrument to short the RTC_RST point . Cleaning BIOS Passwords T o clean the User or Supervisor passwords, perform the following steps: 1. From a DOS prompt, execute clnpwd.e xe 2. Press 1 or 2 to clean the desired password shown on ...

  • Packard Bell TM86 - page 48

    38 Chapter 2 Using Boot Sequence Selector The Boot Sequen ce Selector allows the b oot order to be changed without accessing the BIOS. T o use Boot Sequence Selector , perform the following steps: 1. Enter into DOS. 2. Execute BS.exe to display the usage screen. 3. Select the desired boot seque nc e by entering the corresponding sequence . For exam ...

  • Packard Bell TM86 - page 49

    Chapter 2 39 Using DMITools The DMI (Desktop Management Interface) T ool copies BIOS information to EEPR OM to be used in the DMI pool for hardware managemen t. When the BIOS displays V erifying DMI pool dat a it is checking that the t able correlates with the hardware before sending to the operating system (Windows, etc.). T o update the DMI Pool, ...

  • Packard Bell TM86 - page 50

    40 Chapter 2 Using the LAN MAC EEPROM Utility Y ou can use the MAC.BA T utility to write t he MAC.CFG file to the EEPROM under DOS mode. 1. Use a text editor (for example: Notepad) to open the MAC.CFG file. Y ou can see the MAC.CFG contents as below: 2. In DOS mode, run the MAC.BA T file to write MAC values to eeprom. WriteData = ‘001 122334455&a ...

  • Packard Bell TM86 - page 51

    Chapter 3 41 Machine Disassembly and Replacement IMPORT ANT : The outside housing and color may vary from the mass produced model. This chapter contains step-by-s tep procedures on how to disass emble the notebook computer for maintenance and troubleshooting . Disassembly Requirements T o disassemble the computer , you need the following tool s: ? ...

  • Packard Bell TM86 - page 52

    42 Chapter 3 Pre-disassembly Instructions Before proceeding with the disassembly procedure, make su re that you do the following: 1. T urn off the power to the system and all peripherals. 2. Unplug the AC adapter and all power and signal cables from the system. 3. Place the system on a flat, st able surface. 4. Remove the battery pack. ...

  • Packard Bell TM86 - page 53

    Chapter 3 43 Disassembly Process IMPORT ANT : The LCD Module cannot be disassembled outside of facto ry conditions. If any part of the LCD Module is faulty , such as the camera, antenna or LCD panel, the whole module must be replaced. The disassembly proc ess is divided into the following stages: • External module disassemb ly • Main unit disas ...

  • Packard Bell TM86 - page 54

    44 Chapter 3 External Module Disassembly Process IMPORT ANT : The outside housing and color may vary from the mass produced model. External Modules Disassembly Flowchart The flowchart below gives you a graphic re presentati on of the external module disassembly sequence and instructs you on the co mponents that nee d to be removed during servicing. ...

  • Packard Bell TM86 - page 55

    Chapter 3 45 Removing the Battery Pack 1. T urn computer over . Slide the battery lock in the direction shown. 2. Slide and hold the battery rel ease latch to the release po sition (1), then lift out the battery pack from the main unit (2). NOTE: The battery has been highlighted with a yellow oval as shown in the above image . Pleas e det ach the b ...

  • Packard Bell TM86 - page 56

    46 Chapter 3 Removing the SIM Card 1. See “Removing the Battery Pack” on page 45. 2. Push the SIM card all the way in to eject it. 3. Pull it out from the slot. ...

  • Packard Bell TM86 - page 57

    Chapter 3 47 Removing the SD Dummy Card 1. Push the SD dummy card all the way in to eject it . 2. Pull it out from the slot. ...

  • Packard Bell TM86 - page 58

    48 Chapter 3 Removing the Optical Drive Module 1. See “Removing the Battery Pack” on page 45. 2. Remove the screw securing the ODD module. 3. Pull the optical drive modul e out from th e chassis. Ste p Size Quantity Screw T ype ODD Module M2.5*8 1 ...

  • Packard Bell TM86 - page 59

    Chapter 3 49 4. Remove the two (2) screw s securing the ODD bracket a nd remove the ODD b racket from the optical disk d rive module. 5. Remove the ODD bezel by prying the top edge away and clear of the module . Ste p Size Quantity Screw T ype ODD Bracket M2*3 2 ...

  • Packard Bell TM86 - page 60

    50 Chapter 3 Removing the Logic Lower Door 1. Remove three (3) screws from the Logic Lower Door . 2. Lift the door beginning from the inner edge as shown. 3. Lift the door clear off the device, exposing the HDD, DIMM, and WLAN modules. Ste p Size Quantity Screw T ype Logic Lower door M2.5*8 2 ...

  • Packard Bell TM86 - page 61

    Chapter 3 51 Removing the 3G Module 1. Loosen one (1) screw on the 3G Cover . 2. Lift the 3G Cover from the left edge first, then remove completely . 3. Remove the two (2) antenna cables from the 3G module. Ste p Size Quantity Screw T ype 3G Cover M2.5*8 1 ...

  • Packard Bell TM86 - page 62

    52 Chapter 3 4. Remove one (1) screw from the 3G module. 5. Lift the 3G card from the sl ot. ...

  • Packard Bell TM86 - page 63

    Chapter 3 53 Removing the DIMM Module 1. See “Removing the Logic Lower Door” on page 50. 2. Push out the release latches on both sides of the DIMM socket to release th e DIMM module. 3. Remove the DIMM module. 4. Repeat steps 2 and 3 for the se cond DIMM module if present. ...

  • Packard Bell TM86 - page 64

    54 Chapter 3 Removing the WLAN Module 1. See “Removing the Logic Lower Door” on page 50. 2. Disconnect the two (2) antenn a cables from the WLAN Board. 3. Move the antenna away and remove the one (1) screw to release the WLAN Board . Ste p Size Quantity Screw T ype WLAN Module M2*3 1 ...

  • Packard Bell TM86 - page 65

    Chapter 3 55 4. Detach the WLAN Board from the WLAN socket. NOTE: When reattaching the antennas, ensure th e cables are tucked into the chassis to prevent dama ge. ...

  • Packard Bell TM86 - page 66

    56 Chapter 3 Removing the Hard Disk Drive Module 1. See “Removing the Logic Lower Door” on page 50. 2. Using the pull-tab, slide the HDD Module in the di rection of the arrow to disconnect the interface. 3. Lift the HDD Module clear of the HDD bay . NOTE: T o prevent damage to device, avoid pressing down on it or placi ng heavy objects on top o ...

  • Packard Bell TM86 - page 67

    Chapter 3 57 4. Remove the four (4) screws (two each side ) securing the hard disk to the carrier . 5. Remove the HDD from the carrier . Ste p Size Quantity Screw T ype HDD Carrier M3*3 4 ...

  • Packard Bell TM86 - page 68

    58 Chapter 3 Main Unit Disassembly Process Main Unit Disassembly Flowchart Screw List Ste p Screw Quantity Part No. Lower Cover M2.5*8 1 1 86.WJ802.002 Lower Cover M2*3 5 86.WJ802.004 Upper Cover M2.5*5 7 86.WJ802.001 Power Board M2*3 2 86.WJ802.004 Left S peaker Module M2*3 2 86.WJ802.004 Right S pea ker Module M2*3 2 86.WJ802.004 Card Reader M2*3 ...

  • Packard Bell TM86 - page 69

    Chapter 3 59 T ouchPad Bracket M2*3 2 86.WJ802.004 Mainboard M 2.5*5 1 86.WJ802.001 Thermal Module M1.98*3.0 4 86.WJ802.004 Ste p Screw Quantity Part No. ...

  • Packard Bell TM86 - page 70

    60 Chapter 3 Removing the Keyboard 1. Unlock the six (6) keyboard locks. 2. Pry up the centre of the Keyboard and rotate it upward awa y from the Upper Cover . 3. T urn the keyboard over on to the T ouchPad area to expose the FPC connector . ...

  • Packard Bell TM86 - page 71

    Chapter 3 61 4. Open the locking latch and disco nne ct the FPC from the mainboard . 5. Lift the keyboard clear of the Upper Cover . ...

  • Packard Bell TM86 - page 72

    62 Chapter 3 Removing the Upper Cover 1. See “External Module Disassembly Process” on page 44. 2. T urn the computer over . Remove the eleven (1 1) screws on the lower cover and fi ve (5) screws from the battery bay . Ste p Size Quantity Screw T ype Upper Cover (red callout) M2.5*8 1 1 Battery Bay (green callout) M2*3 5 ...

  • Packard Bell TM86 - page 73

    Chapter 3 63 3. Disconnect the following four (4) cables from the Ma inboard. A B C D ...

  • Packard Bell TM86 - page 74

    64 Chapter 3 NOTE: Avoid pulling on cables directly to prevent damage to the connectors. NOTE: Use the pull-tabs on FFCs whenever available to prevent damage . 4. Release the locking latch on A an d disconnect the cable. 5. Pull the cable off the adhesive as shown. 6. Release the locking latch on B and remove th e cable as shown. 7. Release the loc ...

  • Packard Bell TM86 - page 75

    Chapter 3 65 9. Remove the seven (7) screws on the Upper Cover as shown. 10. S tarting at the top rig ht side of th e cover , pry ap art t he Upper and Lower Covers as shown. W ork along the front edge of the casing to the left as shown, then lift the Upper Cover clear of the Lower Cover . Ste p Size Quantity Screw T ype Upper Cover M2.5*5 7 ...

  • Packard Bell TM86 - page 76

    66 Chapter 3 Removing the Left Speaker Module 1. See “Removing the Upper Co ver” on page 62. 2. Locate the Left S peaker Mo dule on the Upper Cove r as shown. 3. Remove two (2) screws from the left speaker module. 4. Lift the S peaker clear of the Upper Cover . Ensure that the cable is free from all cable clips. Ste p Size Quantity Screw T ype ...

  • Packard Bell TM86 - page 77

    Chapter 3 67 Removing the Right Speaker Module 1. See “Removing the Upper Co ver” on page 62. 2. Locate the Right S pe aker Module on the Upper Cover as show n. 3. Remove the one (1) securing screw from the Right S peaker Module. 4. Remove the Right S peaker Mo dule cable from the cable c hannel. Ensure that the cable is free from all cable cli ...

  • Packard Bell TM86 - page 78

    68 Chapter 3 5. Lift the Right S peaker Module clear of the upper cover . ...

  • Packard Bell TM86 - page 79

    Chapter 3 69 Removing the Power Board 1. See “Removing the Upper Co ver” on page 62. 2. T urn the upper cover over . Pass the cable through the upper cover as shown. 3. Remove two (2) screws from the power board. 4. Remove the power board assembly and lift the power board clear of the device. Step Size Quantity Screw T ype Power board M2*3 2 ...

  • Packard Bell TM86 - page 80

    70 Chapter 3 Removing the TouchPad Bracket IMPORT ANT : The T ouchPad Board cannot be removed ind ividua lly . T o replace the T ouchPad Board, replace the entire Upper Cover . 1. See “Removing the Upper Co ver” on page 62. 2. Lift the FFC to detach the adhesive securing the cable to the Upper Cover . 3. Release the FFC locking latch and discon ...

  • Packard Bell TM86 - page 81

    Chapter 3 71 4. Remove the one (1) screw from T ouchPad bracket. 5. Pry the T ouchpad bracket off the adhesive and remove it as shown. Step Size Quantity Screw T ype T ouchPad Bracket M2*3 1 ...

  • Packard Bell TM86 - page 82

    72 Chapter 3 Removing the Card Reader Board 1. See “Removing the Upper Co ver” on page 62. 2. Unlock the mainboard to card reader cable connector . 3. Remove the cable from the chassis by pulling up on the adhesive. 4. Remove one (1) screw from the card reader board . Ste p Size Quantity Screw T ype Card Reader M2*3 1 ...

  • Packard Bell TM86 - page 83

    Chapter 3 73 5. Lift the card reader board clear of the device. ...

  • Packard Bell TM86 - page 84

    74 Chapter 3 Removing the USB Board 1. See “Removing the Upper Co ver” on page 62. 2. Unlock the mainboard to USB cable connector . 3. Remove the cable from the chassis by pulling up on the adhesive. 4. Remove one (1) screw from the USB board. Ste p Size Quantity Screw T ype USB M2*3 1 ...

  • Packard Bell TM86 - page 85

    Chapter 3 75 5. Lift the USB board clear of the device. ...

  • Packard Bell TM86 - page 86

    76 Chapter 3 Removing the Bluetooth Board 1. See “Removing the Upper Co ver” on page 62. 2. Pry the Bluetooth board from the adhesive. 3. Disconnect the mainboard to Bluetooth cable . 4. Lift the Bluetooth board away from the cable channe l as shown. ...

  • Packard Bell TM86 - page 87

    Chapter 3 77 Removing the Mainboard 1. See “Removing the Upper Co ver” on page 62. 2. Unlock the microphone cable connector and discon nect the cable. 3. Disconnect the L VDS cable. ...

  • Packard Bell TM86 - page 88

    78 Chapter 3 4. Remove the one (1) securing screw from the Mainboard. 5. Without removing completely , lift the mainboard from the chassis from the right edge first. CAUTION: Do not remove the mainbo ard completely . The mainb oard is still connected to the chassis. Ste p Size Quantity Screw T ype Mainboard M2.5*5 1 ...

  • Packard Bell TM86 - page 89

    Chapter 3 79 6. Carefully turn the mainboard over and pl a ce it on a clean, dust-free surface. 7. Disconnect the power cable. 8. Remove the mainboard from the chassis and turn it over . NOTE: Circu it boards >1 0 cm² have been hig hlighted w ith a yell ow rectangle as show n in the previous image. Please det ach the Circuit board and f ollow l ...

  • Packard Bell TM86 - page 90

    80 Chapter 3 9. Remove the adhesive tape from the bluetooth cable. 10. Unlock the connector and disconnect the blueto oth to mainboard cable. ...

  • Packard Bell TM86 - page 91

    Chapter 3 81 Removing the Thermal Module 1. See “Removing the Upper Co ver” on page 62. 2. See “Removing the Mainboard” on page 77. 3. Disconnect the fan cable. 4. Remove the four (4) securing screws (in reverse numeri cal orde r from screw 4 to screw 1) from the Thermal Module. Ste p Size Quantity Screw T ype Thermal Module M1.98*3.0 4 1 2 ...

  • Packard Bell TM86 - page 92

    82 Chapter 3 5. Carefully lift the Thermal Module clear of the Mainboard. ...

  • Packard Bell TM86 - page 93

    Chapter 3 83 Removing the CPU IMPORT ANT : The pins on the underside of the CPU are very delicate. If they are damaged, the CPU may malfunction. Place the CPU on a clean, dry surface when it is not installed. 1. See “Removing the Thermal Module ” on page 81. 2. Using a flat-bladed screw drive r , rotate the CPU locking screw 180° clockwise as ...

  • Packard Bell TM86 - page 94

    84 Chapter 3 LCD Module Disassembly Process LCD Module Disassembly Flowchart Screw List Ste p Screw Quantity Part No. LCD Bezel M2.5*6 2 86.WJ802.003 LCD Panel M2.5*6 2 86.WJ802.003 LCD Brackets M2*3 6 86.WJ802.00 4 Inverter Board M2.5*5 1 86.WJ802.00 1 LCD Assembly M2.5*8 4 86.WJ802.002 Re mo ve LCD Assemb l y Re mo ve Camera Modul e Re mo ve LCD ...

  • Packard Bell TM86 - page 95

    Chapter 3 85 Removing the LCD Assembly 1. See “Removing the Upper Co ver” on page 62. 2. T urn the device over and pass the black and white antenna cables through the lower cover . 3. Free the black and white antenna cables from the cable channel as shown. 4. Continue removing the white antenna cable from the cable channel. ...

  • Packard Bell TM86 - page 96

    86 Chapter 3 5. Remove the L VDS cable from the cable channel. 6. Remove the adhesive tape from the black antenna ca ble an d free the cable from the cable chann el. ...

  • Packard Bell TM86 - page 97

    Chapter 3 87 7. Remove four (4) screws from the LCD assembly . 8. Remove the LCD assembly from the lower cover . Ste p Size Quantity Screw T ype LCD assembly M2.5*8 4 ...

  • Packard Bell TM86 - page 98

    88 Chapter 3 Removing the LCD Bezel 1. See “Removing the LCD Assembly” on page 85. 2. Remove the two (2) bezel screw caps and screws. 3. S tarting from the bottom edge of t he bezel, pry the bezel upwards and aw ay from the panel. W ork along the right side toward the top of the b ezel, prying the cove rs apart. Continue along the to p edge and ...

  • Packard Bell TM86 - page 99

    Chapter 3 89 Removing the Camera Module 1. See “Removing the LCD Assembly” on page 85. 2. Locate the Camera Module at the top of the LCD Module and disconnect the camera cabl e. 3. Remove the Camera from the module. ...

  • Packard Bell TM86 - page 100

    90 Chapter 3 Removing the Inverter Board 1. See “Removing the LCD Assembly” on page 85. 2. Remove the adhesive tape from the inverter cables. 3. Remove one (1) screw from the inverter board. 4. Using both hands, rotate the inverter board arou nd the hook to fre e it from the panel. Ste p Size Quantity Screw T ype Inverter Board M2.5*5 1 ...

  • Packard Bell TM86 - page 101

    Chapter 3 91 5. T urn the board over and disconnect the cable. ...

  • Packard Bell TM86 - page 102

    92 Chapter 3 Removing the LCD Panel 1. See “Removing the Camera Module” on page 89. 2. Remove the two (2) securing screws from the LCD Panel. 3. Remove the adhesive tape from the cable and continue removing the cable from the channel. Ste p Size Quantity Screw T ype LCD Panel M2.5*6 2 ...

  • Packard Bell TM86 - page 103

    Chapter 3 93 4. Lift the LCD Panel clear of the module. ...

  • Packard Bell TM86 - page 104

    94 Chapter 3 Removing the LCD Brackets and FPC Cable 1. See “Removing the LCD Panel” on page 92. 2. Remove the six (6) securing screws (three on each side) from the LCD Panel brackets. 3. Remove the LCD brackets from the LCD Panel. 4. Peel back the mylar securin g the L VDS cable. Ste p Size Quantity Screw T ype LCD Brackets M2*3 6 ...

  • Packard Bell TM86 - page 105

    Chapter 3 95 5. Disconnect the L VDS cable from the panel. ...

  • Packard Bell TM86 - page 106

    96 Chapter 3 Removing the Microphone Cable 1. See “Removing the LCD Panel” on page 92. 2. Remove the cable bundle from the hinge channel. 3. Peel back the foil tabs and remove the microphone cable from the cable chan nel. 4. Continue removing the cable from the cable channel. ...

  • Packard Bell TM86 - page 107

    Chapter 3 97 5. Lift the microphone set clear of the panel. ...

  • Packard Bell TM86 - page 108

    98 Chapter 3 Removing the Antennas 1. See “Removing the LCD Panel” on page 92. 2. Remove the black antenna from the cable channel. 3. Peel back the foil tabs and remove the cable from the cable channel. 4. Pry the antenna assembly clear of the device. ...

  • Packard Bell TM86 - page 109

    Chapter 3 99 5. Remove the white ante nna from the hinge channel. 6. Peel back the foil tabs and remove the cable from the cable channel. 7. Pry the antenna assembly clear of the device. ...

  • Packard Bell TM86 - page 110

    100 Chapter 3 LCD Module Reassembly Procedure Replacing the Antennas 1. Adhere the white antenna assembly to the LCD cover. 2. Run the cable along the cable chann el and fold over the foil tabs to secure the cable in place. 3. Run the white antenna along the hing e channel. ...

  • Packard Bell TM86 - page 111

    Chapter 3 101 4. Adhere the black antenna assembly on the LCD cover . 5. Run the cable along the cable chann el and fold over the foil tabs to secure the cable in place. 6. Run the black antenn a cable along the cable channel. ...

  • Packard Bell TM86 - page 112

    102 Chapter 3 Replacing the Microphone Cable 1. Place the microphone set in the panel. 2. Fold the foil tab over to secure. 3. Fold over the foil tabs and continue running the microphone cable along the cable ch annel indicated between the red callouts. 4. Run the ca ble bundle a long the h inge channel. IMPORT ANT : Ensure that the LCD cable runs ...

  • Packard Bell TM86 - page 113

    Chapter 3 103 Replacing the LCD Brackets and FPC Cable 1. Connect the L VDS cable to the LCD panel. 2. Adhere the L VDS mylar to the LCD panel. 3. Attach the LCD brackets to the LCD Panel. ...

  • Packard Bell TM86 - page 114

    104 Chapter 3 4. Replace six (6) securing screws (three on each side) of the LCD Panel brackets. ...

  • Packard Bell TM86 - page 115

    Chapter 3 105 Replacing the LCD Panel 1. Place the LCD Panel in the mo dule. 2. Run the ca ble along the channel in the LCD Module as shown. 3. Apply the adhesive strip to hold the cable in place. 4. Secure the panel using two (2) securing screws. ...

  • Packard Bell TM86 - page 116

    106 Chapter 3 Replacing the Inverter Board 1. Place the LCD Panel in the mo dule. 2. Run the ca ble along the channel in the LCD Module as shown. 3. Apply the adhesive strip to hold the cable in place. 4. Secure the panel using two (2) securing screws. ...

  • Packard Bell TM86 - page 117

    Chapter 3 107 Replacing the Camera Module 1. Place the Camera in the modul e. 2. Co nnect the camera cable. ...

  • Packard Bell TM86 - page 118

    108 Chapter 3 Replacing the LCD Bezel 1. Replace the bezel and press down until th ere are no gaps between the bezel and the LCD Module. IMPORT ANT : Ensure that the LCD cables pass through th e hinge wells and are not trapped by the bezel. 2. Replace the two (2) screws and screw caps. ...

  • Packard Bell TM86 - page 119

    Chapter 3 109 Replacing the LCD Assembly 1. Place the LCD assembl y on the l ower cov er . 2. Secure the LCD assembly using four (4) screws. ...

  • Packard Bell TM86 - page 120

    11 0 Chapter 3 3. Replace the adhesive tape and run the bl ack ante nna cable along the ca ble channel. 4. Near the left hinge, run the L VDS cable along th e cable channel. ...

  • Packard Bell TM86 - page 121

    Chapter 3 111 5. Run the white antenn a cable along the cable channel as shown. 6. Run the black antenn a cables along the cable channel. 7. Pass the black and white antenna cables through the lowe r cover . ...

  • Packard Bell TM86 - page 122

    11 2 Chapter 3 Main Module Reassembly Procedure Replacing the CPU IMPORT ANT : The CPU has a Pin1 locator that must be positi one d corresponding to the marker on the CPU socket. 1. Place the CPU into the CPU socket as shown, taking note of the Pin1 locator . 2. Using a flat-bladed screw driver , rot ate the CPU lockin g screw 180° counter-clockwi ...

  • Packard Bell TM86 - page 123

    Chapter 3 11 3 Replacing the Thermal Module IMPORT ANT : Apply a suitable thermal grease and ensure all heat pads are in place before replacing the Thermal Module. The following thermal grease type s are approved for use: • Silmore GP50 • Honeywell • Jet Motor 7762 The following thermal pads are approved for use: • Eapus XR-PE 1. Remove all ...

  • Packard Bell TM86 - page 124

    11 4 Chapter 3 Replacing the Mainboard 1. Connect the Bluetooth to mainboa rd cable. 2. Apply the adhesive tape to the Bluetooth cable. 3. Place the mainboard on a clean, dust-free surface. Connect the power cable. NOTE: Ensure the I/O ports are positioned correctly thro ugh the casing. ...

  • Packard Bell TM86 - page 125

    Chapter 3 11 5 4. Place the mainboard in the chassis, left edge first to line up the I/O ports. 5. Secure the one (1) securing screw on the Mainboard. ...

  • Packard Bell TM86 - page 126

    11 6 Chapter 3 6. Connect the L VDS cable and lock the connector . 7. Connect the microphone cable. ...

  • Packard Bell TM86 - page 127

    Chapter 3 11 7 Replacing the Bluetooth Board 1. Run the bluetooth cable along the channel as shown. 2. Connect the mainboard to bluetooth cable. 3. Adhere the bluetooth bo ard to the adhesive . ...

  • Packard Bell TM86 - page 128

    11 8 Chapter 3 Replacing the USB Board 1. Place the USB board in the device. 2. Secure the one (1) screw on the USB board. 3. Connect the USB cable to the mainb oard and lock the connector . ...

  • Packard Bell TM86 - page 129

    Chapter 3 11 9 Replacing the Card Reader Board 1. Place the card reader board in the device. 2. Secure one (1) screw on the card reader board. 3. Connect the card reader cable and lock th e connector . ...

  • Packard Bell TM86 - page 130

    120 Chapter 3 Replacing the TouchPad Bracket 1. Replace the T ouchPad bracket top edge first to engage the securing clips and press down firmly . 2. Replace the one (1) screw to secure the T ouchPad Bracket to the Upper Cover . 3. Replace the T ouchPad FFC and close the locking latch on the connector . ...

  • Packard Bell TM86 - page 131

    Chapter 3 121 4. Replace the FF C and press down a s indicated to secure it to the Upper Cover . ...

  • Packard Bell TM86 - page 132

    122 Chapter 3 Replacing the Power Board 1. Place the power board in the chassis. A dhere the power board assembly as sh own. 2. Secure two (2) screws on the power board. 3. Pass the power board cable through the uppe r co ver . Adhere the power board cable as shown. ...

  • Packard Bell TM86 - page 133

    Chapter 3 123 Replacing the Right Speaker Module 1. Place the right speaker module in the chassis as shown. 2. Run the speaker cable along the channel. 3. Secure the one (1) securing screw on the Right S peaker Module. ...

  • Packard Bell TM86 - page 134

    124 Chapter 3 Replacing the Left Speaker Module 1. Place the module righ t side fir st on the Up per Cover as shown. 2. Run the S peake r cable along the cable channel. 3. Secure two (2) screws from the left speaker module. ...

  • Packard Bell TM86 - page 135

    Chapter 3 125 Replacing the Upper Cover 1. Place the Upper Cover on the Lower Cover as shown. 2. Secure the seven (7) screws on the Upper Cover as shown. ...

  • Packard Bell TM86 - page 136

    126 Chapter 3 3. Connect the following cables to the Mainboard. 4. Connect D as shown. 5. Connect C as shown. A B C D ...

  • Packard Bell TM86 - page 137

    Chapter 3 127 6. Connect B as shown. 7. Connect A as shown. 8. T urn the computer over . Replace the ele ven (1 1) screw s on the lower cover and five (5) screws from the battery bay . ...

  • Packard Bell TM86 - page 138

    128 Chapter 3 Replacing the Keyboard 1. Connect the Keyboard FFC to the Mainboard and cl os e the locking latch to secure the cable in place. 2. Replace the Keyb oard by first lining up the bottom edg e. Press down firmly to l ock. ...

  • Packard Bell TM86 - page 139

    Chapter 3 129 Replacing the Hard Disk Drive Module 1. Place the HDD in the HDD carrier . 2. Replace the four (4) screws (two each side) to secure the carrier . 3. Insert the HDD, as indica ted and lower it into place. 4. Slide the HDD in the direction of the arrow to connect the interface. ...

  • Packard Bell TM86 - page 140

    130 Chapter 3 Replacing the WLAN Module 1. Insert the WLAN Module into the WLAN socket. 2. Replace th e one (1) screw to secure the module. 3. Connect the two (2) Ante nna cables to the mod ule. NOTE: The black cable connects to the upper terminal (MAIN) and the white cable to the lower termi nal (MAIN). ...

  • Packard Bell TM86 - page 141

    Chapter 3 131 Replacing the DIMM Modules 1. Insert the DIMM Module in place. 2. Press down to lock the DIMM module in place. 3. Repeat steps for the second DIMM module if present. ...

  • Packard Bell TM86 - page 142

    132 Chapter 3 Replacing the 3G Module 1. Insert the 3G card into the slot. 2. Replace one (1) screw from the 3G module. 3. Connect two (2) antenna cables. ...

  • Packard Bell TM86 - page 143

    Chapter 3 133 4. Line up the right edge of the 3G cover and replace. 5. Secure one (1) screw on the 3G Cover . ...

  • Packard Bell TM86 - page 144

    134 Chapter 3 Replacing the Logic Lower Door 1. Replace the door by first lining up the top edge as shown. 2. Secure three (3) screw s on the lower cover . ...

  • Packard Bell TM86 - page 145

    Chapter 3 135 Replacing the ODD Module 1. Press the bezel into the tr ay , bottom edge fi rst, to secure it to the ODD Module. 2. Place the bracket on the ODD mo dule. 3. Secure the ODD bracket with the two (2) screws. 4. Push the ODD Module into the ODD bay until it is flush with the casing. 5. Replace the one (1) screw to secure the Module. ...

  • Packard Bell TM86 - page 146

    136 Chapter 3 Replacing the SD Dummy Card 1. Insert the SD Dum my Card into the slot as shown. 2. Push until the ca rd cli cks into place an d is fl ush wit h the casing . ...

  • Packard Bell TM86 - page 147

    Chapter 3 137 Replacing the SIM Card 1. Insert the SIM Card into the slot as shown. 2. Push until the ca rd cli cks into place an d is fl ush wit h the casing . ...

  • Packard Bell TM86 - page 148

    138 Chapter 3 Replacing the Battery 1. Slide and hol d the battery rele ase latch to the release po sition (1 ), insert t he batter y pack and press down (2). 2. Slide the battery lock in the direction shown to secure the battery in place. 1 2 ...

  • Packard Bell TM86 - page 149

    Chapter 4 139 Troubleshooting Common Problems Use the following procedure as a gui de for computer problems. NOTE: The diagnosti c tests are intended to test only Acer products. Non-Acer products, prototype cards, or modified options can give false e rrors and invalid system responses. 1. Obtain the failing symptoms in as much detail as possible. 2 ...

  • Packard Bell TM86 - page 150

    140 Chapter 4 Power On Issue If the system doesn’t power on, perform the following acti ons one at a time to correct the problem. Do not replace a non-defective FRUs: Computer Shutsdown Intermittently If the system powers off at intervals, perform the fo llowing actions one at a time to correct the problem. 1. Check the power cable is properly co ...

  • Packard Bell TM86 - page 151

    Chapter 4 141 No Display Issue If the Displa y doesn’t work, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs: No POST or Video If the POST or video doesn’t display , perform the foll owing actions one at a time to correct the problem. 1. Make sure that the internal display is se lected. On ...

  • Packard Bell TM86 - page 152

    142 Chapter 4 Abnormal Video Display If video displays abnormally , perform the following actions one at a time to correct the problem. 1. Reboot the computer . 2. If permanent vertical/horizon tal lines or dark spots display in the same location, the LCD is faulty and should be replaced. See “Disassembly Process” on page 43. 3. If extensiv e p ...

  • Packard Bell TM86 - page 153

    Chapter 4 143 LCD Failure If the LCD fails, perform the following actions one at a time to correct the problem. Do not replace a non- defective FRUs: Built-In Keyboard Failure If the built-in Keyboard fails, perform the foll owing actions one at a ti me to correct the pro blem. Do not replace a non-defective FRUs: ...

  • Packard Bell TM86 - page 154

    144 Chapter 4 TouchPad Failure If the To u c h P a d doesn’t work, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs: Internal Speaker Failure If the internal Speakers fail, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs: ...

  • Packard Bell TM86 - page 155

    Chapter 4 145 Sound Problems If sound problems are experienced, p erform the following actions one at a time to correct the problem. 1. Reboot the computer . 2. Navigate to Start ´ Control Panel ´ System and Maintenance ´ System ´ Device Manager . Check the Device Manager to determine that: • The device is properly installed. • There are no ...

  • Packard Bell TM86 - page 156

    146 Chapter 4 HDD Not Operating Correctly If the HDD does not op erate correctly , perform the following ac tions one at a time to correct the problem. 1. Disconnect all external devices. 2. Run a complete virus scan using up-to-date software to ensure the computer is virus free. 3. Run the Windows 7 S tartup R epair Utility: a. insert the Windows ...

  • Packard Bell TM86 - page 157

    Chapter 4 147 ODD Failure If the ODD fails, perform the following acti ons one at a time to correct the problem. Do not replace a non- defective FRUs: ODD Not Operating Correctly If the ODD exhibits any of the following symptoms it may be faulty: • Audio CDs do not play when loaded • DVDs do not play when loaded • Blank discs do not burn corr ...

  • Packard Bell TM86 - page 158

    148 Chapter 4 a. Double-click lDE A T A/A T API controllers . If a device displays a down arrow , right-click on the device and click Enable . b. Double-click DVD/C D-ROM d rives . If the device displays a down arrow , right-click on the device and click Enable . c. Check that th ere are no yellow exc l amation marks a gainst the items in l D E ATA ...

  • Packard Bell TM86 - page 159

    Chapter 4 149 b. Double-click IDE A T A/A T API controllers , then right-click A T A Device 0. c. Click Properties and select the Advanced Settings tab. Ensure that the Enable DMA box is checked and click OK . d. Repeat for the other A T A Devices show n if applicable. Drive Not Detected If Windows cannot detect the drive, perform the foll owing ac ...

  • Packard Bell TM86 - page 160

    150 Chapter 4 Wireless Function Failure If the WLAN fails, perform th e following actions one at a time to correct th e problem. Do not replace a non- defective FRUs: Thermal Unit Failure If the Thermal Unit fails, perform the follo wing actions one at a time to correct the problem. Do not replace a non-defective FRUs: ...

  • Packard Bell TM86 - page 161

    Chapter 4 151 External Mouse Failure If an external Mouse fails, perform the following actions one at a time to correc t the problem. 1. T ry an alternative mouse. 2. If the mouse uses a wireless connection, insert new batteries a nd confirm there is a good connection. See the mouse user manual. 3. If the mouse uses a USB connecti on, try an altern ...

  • Packard Bell TM86 - page 162

    152 Chapter 4 Intermittent Problems Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware defect, such as: cosmic radiation, electros tatic discharge, or software errors. FRU repla cement should be considered only when a recurring prob lem exists. When analyzing an intermittent prob lem, do ...

  • Packard Bell TM86 - page 163

    Chapter 4 153 Post Codes These tables describe the POST code s and descriptions durin g the POST . Post Code Range SEC Phase POST Code T able NOTE: The color ba r items indi cate 3rd p arty re lated functions that are platorm dep endent. Phase POST Code Range SEC 0x01 - 0x0F PEI 0x70 - 0x9F DXE 0x40 - 0x6F BDS 0x10 - 0x3F SMM 0xA0 - 0xBF S3 0xC0 - ...

  • Packard Bell TM86 - page 164

    154 Chapter 4 PEI Phase POST Code T able: NOTE: The color ba r items indi cate 3rd p arty re lated functions that are platorm dep endent. Functionali ty Name (Inc lude PostCode.h) Phase Post Code Description PEI_SIO_INIT PEI 70 Super I/O Initialization PEI_CPU_REG_INIT PEI 71 CPU Early Initialization PEI_CPU_AP_INIT PEI 72 Multi-processor Early In ...

  • Packard Bell TM86 - page 165

    Chapter 4 155 DXE Phase POST Code T able: NOTE: The color ba r items indi cate 3rd p arty re lated functions that are platorm dep endent. Functional ity Name (Includ e PostCode.h ) Phase PostCode Description DXE_TCGDXE DXE 40 TPM initial in DXE DXE_SB_SPI_INIT DXE 41 South bridge SPI initialization DXE_CF9_RESET DXE 42 Setup Reset service DXE_SB_S ...

  • Packard Bell TM86 - page 166

    156 Chapter 4 BDS Phase POST Code T able: Functionali ty Name (Inc lude PostCode.h) Phase Post Code Description BDS_ENTER_BDS BDS 10 Enter BDS entry BDS_INST ALL_HOTKEY BDS 1 1 Install Hotkey service BDS_ASF_INIT BDS 12 ASF Initialization BDS_PCI_ENUMERA TION_ST ART BDS 13 PCI enumeration BDS_BEFORE_PCIIO_INST ALL BDS 14 PCI resource assign comple ...

  • Packard Bell TM86 - page 167

    Chapter 4 157 NOTE: The color ba r items indi cate 3rd p arty re lated functions that are platorm dep endent. PostBDS POST Code T able S3 Functions POST Code T able ACPI Functions POST Code T able SMM Functions POST Code T able BDS_RECOVERY_ST ART_FLASH BDS 35 Fast Recovery S tart Flash. Functionali ty Name (Inc lude PostCode.h) Phase Post Code De ...

  • Packard Bell TM86 - page 168

    158 Chapter 4 InsydeH2ODD T Debugger POST Co de T able SMM_ACPI_DISABLE_ST AR T SMM 0xA8 OS call ACPI disable function SMM_ACPI_DISABLE_END SMM 0xA9 ACP I disable function complete Functional ity Name (Include P ostCode.h) PostCode Description Used by Insyde debugger 0x0D Waiting for device connect Used by Insyde debugger 0xD0 Waiting for device c ...

  • Packard Bell TM86 - page 169

    Chapter 5 159 Jumper and Connector Locations Top View Item Description Item Description JL VDS1 Connect to LED / CCFL Panel JLED1 Connect to Powerboard (FFC) JSPK2 Connect to Left S peaker JLE D2 Connect to Powerboard (FFC) JSPK1 Connect to Right S peaker JP1 Connect to internal MIC JKB1 Connect to Keyboard SW2/SW3 Left button / Right button JTP1 C ...

  • Packard Bell TM86 - page 170

    160 Chapter 5 Bottom View Item Description Item Description PJP2 Connect to Battery JHP1 Connect to external headphone PJP1 DC-IN jack JBT1 Connect to BT JDIMM1/ JDIMM2 DDR3 memory socket J HDD1 Connect to SA T AHDD JCRT1 Connect to external CR T JODD1 Connect to SA T AODD JRJ45 RJ45 LAN JP4 Connect to 3G board JHDMI1 HDMI connector JF AN1 Connect ...

  • Packard Bell TM86 - page 171

    Chapter 5 161 USB/B Board Power Board ITEM DESCRI PTION JUSB1/JUSB2 USB Connector ITEM DESCRIPTION ITEM DESCRIPTION LED1 For NEW70 ON/OFF LED LED9 For NEW50 WW AN LED LED2 For NEW80 ON/OFF LED LED10 For NEW70 WLAN LED LED3 For NEW90 ON/OFF LED LED1 1 For NEW50 POWER LED LED4 For NEW70 MEDIA LED LED12 For NEW50/NEW90 WLAN LED LED5 For NEW80 MEDIA LE ...

  • Packard Bell TM86 - page 172

    162 Chapter 5 3G/B Board CR/B Board ITEM DESCRI PTION JMINI2 Conn ect to WWAN JSIM1 S IM card connector JP1 Connector to MB (FFC) ITEM DESCRI PTION JREAD1 Card reader connector ...

  • Packard Bell TM86 - page 173

    Chapter 5 163 Clearing Password Check and BIOS Recovery This section provides you with the st andard operating procedures of clearing p a ssword and BIOS recovery for the Packard Bell EasyNote TM86/TM87/TM89. The machine provid es one Hardware Open Gap on main board for clearing password check, and one Hotkey for enabling BIOS Recove ry . Clearing ...

  • Packard Bell TM86 - page 174

    164 Chapter 5 BIOS Recovery by Crisis Disk BIOS Recovery Boot Block: BIOS Recovery Boot Block is a spec ial block of BIOS. It is used to boot up the system with minimum BIOS initialization. Users can enable this feature to restore the BIOS firmware to a successful one once the previous BIOS flashing process failed. BIOS Recovery Hotkey: The system ...

  • Packard Bell TM86 - page 175

    Chapter 6 165 FRU (Field Replaceable Unit) List This chapter gives you the FRU (Field Replaceable Unit) list ing in global configurations of Packard Bell EasyNote TM86/ TM87/TM89. Refer to this chapter whe never ordering for part s to repair or for RMA (Return Merchandise Authorization). Please note that WHEN ORDERING FRU P ARTS, you should c heck ...

  • Packard Bell TM86 - page 176

    166 Chapter 6 EasyNote Exploded Diagrams Main Assembly No. Description Acer P/N No. Description Acer P/N 1 Keyboard KB.I170G .083 6 3G Module TBD 2 Upper Cover 60.WJ802.001 7 Card Reader 55.WJ802.002 3 Mainboard MB.WJU02.001 8 USB Board 55.WJ802.003 4 CPU KC.52001.DMP 9 Lower Cover 60.WJ802.002 5 Thermal Module 60.WJ802.006 1 2 3 4 5 6 7 8 9 ...

  • Packard Bell TM86 - page 177

    Chapter 6 167 Upper Assembly No. Description Ac er P/N 1 T ouchpad Bracket 33.WJ802.001 2 T ouchpad Cable 50.WJ802.003 3 T ouchpad Board TBD 4 T ouchpad Assy TBD 5 Power Board 55.WJ802.001 6 S peaker Ri ght 23.WJ80 2.002 7 S peaker Le ft 23.WJ802.003 8 Upper Cover 60.WJ802.001 1 2 3 4 5 6 7 8 ...

  • Packard Bell TM86 - page 178

    168 Chapter 6 LCD Assembly No. Description Acer P/N No. Descr iption Acer P/N 1 LCD Bezel 60.WJ802.004 6 LCD Panel LK.15605.010 2 LCD Bracket (L) 33.WJ802.004 7 L VDS Cable 50.WJ802.006 3 Antenna Cable (Main) 50.WJ802.004 8 Antenna Cable (Aux) 50.WJ802.005 4 Microphone Cable 23.WJ802.001 9 Camera Module 57.WJ802.001 5 LCD Bracket (R) 33.WJ802.004 1 ...

  • Packard Bell TM86 - page 179

    Chapter 6 169 FRU List CA TEGOR Y Acer Description AcerPN BOARD FOXCONN BLUETOOTH BRM 2046 BT2.1 (T60H928.33) F/ W:861 BH.21 100.004 TBD FOXCONN BLUETOOTH A T H AR301 1 BH.21 100.005 POWER BOARD 55.WJ802.001 CARD READER BOARD 55.WJ802.002 USB BOARD 55.WJ802.003 FOXCONN WIRELESS LAN A THEROS HB93 2X2 BGN (HM) NI.23600.062 LITEON WIRELESS LAN A THERI ...

  • Packard Bell TM86 - page 180

    170 Chapter 6 POWER CORD ARGENTIN A 3 PIN 27.APV02.001 CASE/COVER/BRACKET ASSEMBL Y UPPER CASE ASSY , INCL. TP/T P MYLAR-SLIVER 60.WJ802.001 UPPER CASE ASSY , INCL. TP/TP MYLAR-RED 60.WJL02.001 UPPER CASE ASSY , INCL. TP/TP MYLAR-BLUE 60.WJU02.001 LOWER CASE 60.WJ802.002 LOGIC LOWER DOOR 42.WJ802.001 3G DOOR 42.WJ802.002 TP BRACKET 33.WJ802.001 HDD ...

  • Packard Bell TM86 - page 181

    Chapter 6 171 KEYBOARD Keyboard GA TEW A Y GP-7Tv2 SJM51 Internal 17 S tandard 103KS White US International KB.I170G .083 Keyboard GA TEW A Y GP-7Tv2 SJM51 Internal 17 S tandard 103KS White Greek KB.I170G .068 Keyboard GA TEW A Y GP-7Tv2 SJM51 Internal 17 S tandard 103KS White Arabic KB.I170G .059 Keyboard GA TEW A Y GP-7Tv2 SJM51 Internal 17 S tan ...

  • Packard Bell TM86 - page 182

    172 Chapter 6 Keyboard GA TEW A Y GP-7Tv2 SJM51 Internal 17 S tandard 104KS White CZ/SK KB.I170G .062 Keyboard GA TEW A Y GP-7Tv2 SJM51 Internal 17 S tandard 104KS White Brazilian Portugue se KB.I170G .061 LCD LCD COVER IMR PB-SLIVER 60.BHN02.001 LCD COVER IMR PB-RED 60.BHY02.001 LCD COVER IMR PB-BLUE 60.BJ202.001 LCD BEZEL FOR W/CMOS PB 60.BHN02.0 ...

  • Packard Bell TM86 - page 183

    Chapter 6 173 HEA TSINK THERMAL MOUDLE-UMA 60.WJ802.006 THERMAL MOUDLE-P ARK 60.WJ702.001 THERMAL MOUDLE-MADISON 60.WJF02.001 SPEAKER MIC SET 23.WJ802.001 SPEAKER R 23.WJ802.002 SPEAKER L 23.WJ802.003 MISCELLANEOUS LCD SCREW P AD 47.WJ802.001 CPU/PROCESSOR CPU INTEL CORE I5 520M 2.4G 3M KC.52001.DMP CPU INTEL CORE I5 430M PGA 2.26G ARD, UP TO SC 2. ...

  • Packard Bell TM86 - page 184

    174 Chapter 6 HDD SEAGA TE 2.5" 5400RPM 500GB ST9500325AS WY A TT SA T A LF F/W:0001SDM1 KH.50001.01 1 HDD HGST 2.5" 5400RPM 500GB HTS545050B9A300 P ANTHER B SA T A LF F/W:C60F DISK IMBALANCE CRIT ERIA = 0.014G-CM KH.50007.010 HDD SEAGA TE 2.5" 5400RPM 160GB ST9160314AS WY A TT SA T A LF F/W:0001SDM1 KH.16001.042 HDD SEAGA TE 2.5&quo ...

  • Packard Bell TM86 - page 185

    Chapter 6 175 BA TTER Y BA TTERY SANYO AS10D LI-ION 3S2P SANYO 6 CELL 4400MAH MAIN COMMON ID:AS10D31 BT .00603.1 1 1 BA TTERY SAMSUNG AS10D LI-ION 3S2P SAMSUNG 6 CELL 4400MAH MAIN COMMON ID:AS10D61 BT .00606.008 BA TTERY SIM PLO AS10D LI-ION 3S2P P ANASONIC 6 CELL 4400MAH MAIN COMMON ID:AS10D71 BT .00607.125 BA TTERY SIMPLO AS10D LI-ION 3S2P SA MSU ...

  • Packard Bell TM86 - page 186

    176 Chapter 6 Screw List CA TEGOR Y DESCRIPTION Acer PN SCREW SCREW 2.5D 5L K 5.5D ZK NL CR3 86.WJ802.001 SCREW 2.45D 8.0L K 5.5D 0.8T ZK NL 86.WJ802.002 SCREW 2.5D 6L K 5.5D NI NL 86.WJ802.003 SCREW 1.98D 3.0L K 4.6D 0.8T ZK NL 86.WJ802.004 SCREW 3.0D 3.0L K 4.9D NI 86.WJ802.005 SCREW ASSY CPU THERMAL 86.WJ802.006 ...

  • Packard Bell TM86 - page 187

    Chapter 6 177 ...

  • Packard Bell TM86 - page 188

    Appendix A 178 Model Definition and Configuration Appendix A ...

  • Packard Bell TM86 - page 189

    179 Appendix A Packard Bell EasyNote TM86 Model Acer Part No RO Co untry Description ENTM86- 434G64Bn LX.BJX02.002 EMEA France ENTM86-434G64Bn W7HP64BTFR1 N1 1PGV2H1GBCsk_3V3 2*2G/640/ 6L2.2/5R/CB_bgn_1.3C_GEs_FR51 EASYNOTE_TM86-JO-228FR ENTM86- 334G50Mn S2.BJX02.002 WW WW ENTM86 -334G50Mn W7HP64BW W2 N1 1PGV2H1GBCsk_3V3 2*2G/500_L/ BT/6L2.2/5R/CB_ ...

  • Packard Bell TM86 - page 190

    Appendix A 180 Model Acer Part No CPU LCD VGA Chip VRAM 1 Memory 1 Memory 2 ENTM86- 434G64Bn LX.BJX02.002 Ci5430M NLED15.6 WXGAG N1 1PG V2H 1G-DDR3 (64*16*8) SO2GBII I10 SO2GBIII 10 ENTM86- 334G50Mn S2.BJX02.002 Ci3330M NLED15.6 WXGAG N1 1PG V2H 1G-DDR3 (64*16*8) SO2GBII I10 SO2GBIII 10 ENTM86- 434G64Mn LX.BJX02.001 Ci5430M NLED15.6 WXGAG N1 1PG V2 ...

  • Packard Bell TM86 - page 191

    181 Appendix A ENTM86- 334G32Mn LX.BHP02.001 N N N320GB 5.4KS NN S M 8 X S N ENTM86- 433G32Mn S2.BHP02.003 N N N320 GB 5.4KS NN S M 8 X S N ENTM86- 334G25Mn S2.BHP02.002 N N N250 GB 5.4KS NN S M 8 X S N ENTM86- 332G16Mn S2.BHP02.001 N N N160 GB 5.4KS NN S M 8 X S N ENTM86- 334G32Mn LX.BHN02.002 N N N320GB 5.4KS NN S M 8 X S N ENTM86- 334G50Mn LX.BH ...

  • Packard Bell TM86 - page 192

    Appendix A 182 Packard Bell EasyNote TM87 Model Acer Part No RO Country Description ENTM87- 434G64Bn S2.BJY02.002 WW WW ENTM87-434G64Bn W7HP64BWW 2 N1 1PGV2H1GBCrk_3V3 2*2G/640/BT/ 6L2.2/5R/CB_bgn _1.3C_GEr_EN1 1 ENTM87- 334G32Mn LX.BJY02.001 EMEA France ENTM87-334G32Mn W7HP64 BTFR1 N1 1PGV2H1GBCrk_3V3 2*2G/320/BT/ 6L2.2/5R/CB_bgn _1.3C_GEr_FR51 EA ...

  • Packard Bell TM86 - page 193

    183 Appendix A ENTM87- 333G25Bn S2.BJ002.001 Ci3330M NLED15.6 WXGAG PA R K _XT 512M- DDR3 (64*16*4) SO1GBI II10 SO2GBIII 10 ENTM87- 524G50Mn LX.BJ002.001 Ci5520M NLED15.6 WXGAG PA R K _XT 512M- DDR3 (64*16*4) SO2GBI II10 SO2GBIII 10 ENTM87- 332G16Mn S2.BJ00C.001 Ci3330M NLED15.6 WXGAG PA R K _XT 512M- DDR3 (64*16*4) SO2GBI II10 N ENTM87- 334G32Mn L ...

  • Packard Bell TM86 - page 194

    Appendix A 184 ENTM87- 334G50Mn LX.BJ002.002 NIS 5 in 1-Build in 3rd WiF i 2x2 BGN NN ENTM87- 333G25Bn S2.BJ002.001 NIS 5 in 1-Build in 3rd WiF i 2x2 BGN NN ENTM87- 524G50Mn LX.BJ002.001 NIS 5 in 1-Build in 3rd WiF i 2x2 BGN BT 2.1 N ENTM87- 332G16Mn S2.BJ00C.001 N 5 in 1-Build in 3rd WiFi 2x2 BGN NN ENTM87- 334G32Mn LX.BHY02.001 NIS 5 in 1-Build i ...

  • Packard Bell TM86 - page 195

    185 Appendix A Packard Bell EasyNote TM89 Model Acer Part No RO Country Description ENTM89- 522G16Mn S2.BJZ02.001 WW WW ENTM89-522G16Mn W7HP64BWW2 N1 1PGV2H1GBCbk_3V3 1*2G/16 0/6L2.2/ 5R/CB_bgn_1.3C_GEb_EN1 1 ENTM89- 332G16Mn S2.BJ302.001 WW WW ENTM89-332G16Mn W7HP64BWW2 P ARK_XT512Cbb 1*2G/160/6L2.2/5R/ CB_bgn_1.3C_GEb_EN1 1 ENTM89- 433G50Bn S2.BJ ...

  • Packard Bell TM86 - page 196

    Appendix A 186 Model Acer Part No Extra SW1 Card Reader Wireless LAN1 Bluetooth VOIP Phone Finger Print ENTM89- 522G16Mn S2.BJZ02.001 NIS 5 in 1- Build in 3rd WiFi 2x2 BGN NN N ENTM89- 332G16Mn S2.BJ302.001 NIS 5 in 1- Build in 3rd WiFi 2x2 BGN NN N ENTM89- 433G50Bn S2.BJ202.002 NIS 5 in 1- Build in 3rd WiFi 2x2 BGN NN N ENTM89- 433G50Bn S2.BJ202.0 ...

  • Packard Bell TM86 - page 197

    Appendix B 187 Test Compatible Components This computer ’s compat ibility is tested and verified by Acer ’s internal testing department. All of its system functions are tested under Windows ® 7 environment. Refer to the following lists for components, adapter ca rds, and peripherals which have passed these tests. Regarding configuration, combi ...

  • Packard Bell TM86 - page 198

    188 Appendix B Microsoft ® Windows ® 7 Environment Test Category V end or Description PN CPU Arrandale 2.13G (Ci3330M) Intel IC CP80617004122AG SLBMD C2 2.13G PGA988 KC.33001.DMP Arrandale 2.26G (Ci3350M) Intel IC CP80617004161AC SL BPK C2 2.26G PGA988 KC.35001.DMP Arrandale 2.26G (Ci5430M) Intel IC CP80617004161 AD SLBPN C2 2.26 G PGA988 KC.4300 ...

  • Packard Bell TM86 - page 199

    Appendix B 189 1G DDR3- 1333 SAMSUNG M471B2873FHS-CH9 KN.1GB0B.035 RAM SODIMM DDR3-2G 1333 2G DDR3- 1333 SAMSUNG M471 B5673FH0-CH9 LF KN.2GB0B.023 RAM SODIMM DDR3-4G 1333 4G DDR3- 1333 SAMSUNG M471B5273CH0-CH9 KN.4GB0B.01 0 4G DDR3- 1333 ELPIDA DDDR3 4G EBJ41UF8BAS0-DJ-F KN.4GB09.001 LCD N15.6WXGAG N15.6WXG AG AUO (70/80/ 90) LCD MODU B156XW01 V2 1 ...

  • Packard Bell TM86 - page 200

    190 Appendix B 250G 5.4K rPm TOSHIBA HDD 250G .37"H MK2565GSX 0F A KH.25004.005 250G 5.4K rPm HGST HDD 250G .37"H HTS545025B9 A300 L/V 0F A KH.25007.016 250G 5.4K rPm WD HDD 250G .37"H WD2500BEVT -22A2 3T0 0F A KH.25008.025 320G 5.4K rPm SEAGA TE HDD 320G 2.75"W .3 7"H ST9320325AS 0F A KH.32001.017 320G 5.4K rPm TOSHIBA HDD ...

  • Packard Bell TM86 - page 201

    Appendix B 191 VRAM 1GB SAMSUNG VRAM SAMSUNG GraPhi c DDRIII 800 1Gb K4W1G1646E-HC12 LF VR.1GB0B.006 1GB HYNIX VRAM HYNIX GraPhic DDRIII 800 1Gb H5TQ1G63 BFR-12C LF VR.1GB0G .004 1GB AMD VRAM A TI GraPhic DDRIII 800 1Gb 23EY2387MA12-SZ LF+HF VR.1GB0T .002 512MB SAMSUNG 512MB HYNIX 512MB AMD NB ChiPset PCH INTEL S IC BD82HM57 QMNS B3 FCBGA 1071 PCH ...

  • Packard Bell TM86 - page 202

    192 Appendix B Sunrex KB V104702 SUNREX INT'E 09F DARFON (NEW90) KB 9Z.N1H82 DARFON INT'E 0C8 GP8T Chicony (NEW90) KB MP-09B2 CHICONY IN T'E 0C8 GP8T Sunrex (NEW90) KB V104702 SUNREX INT'E 0C8 GP8T T ouch Pad MUL TI SYNAPTICS TRACK P AD SYNA PTICS TM-01 146-005 MUL TI MUL TI ALPS TRACK P AD ALPS KGDFF0026A MUL TI- FINGER MUL TI ...

  • Packard Bell TM86 - page 203

    Appendix B 193 LCD_BRK_ L_156_AS SY SZS NEW80_LCD_BRK_L_156_ASSY LCD_BRK_ L_156_AS SY LH NEW80_LCD_BR K_L_156_ASSY LCD_BRK_ L_156_AS SY CHAOLI NEW80_LCD_BRK_L_156_ASSY LCD_BRK_ L_156_AS SY S.H. NEW80_LCD_ BRK_L_156_ASSY LCD_BRK_ R_156_AS SY SZS NEW80_LCD_BRK_R_156_ASSY LCD_BRK_ R_156_AS SY LH NEW80_LCD_BRK_R_156_ASSY LCD_BRK_ R_156_AS SY CHAOLI NEW ...

  • Packard Bell TM86 - page 204

    194 Appendix B LCD_BRK_ L_156_AS SY SH NEW90_LCD_BRK_L_156_ASSY LCD_BRK_ L_156_AS SY LH NEW90_LCD_BR K_L_156_ASSY LCD_BRK_ R_156_AS SY SZS NEW90_LCD_BRK_R_156_ASSY LCD_BRK_ R_156_AS SY SH NEW90_LCD_BRK_R_156_ASSY LCD_BRK_ R_156_AS SY LH NEW90_LCD_BRK_R_156_ASSY LED_BRK_ L_156_AS SY SZS NEW90_LED _BRK_L_156_ASSY LED_BRK_ L_156_AS SY SH NEW90_LED_BRK ...

  • Packard Bell TM86 - page 205

    Appendix B 195 Mini-card WLAN (3rd WiFi BG) (NEW70) Foxconn (NEW70) W/L CARD 085 T77H121.01 54MBPS HB95 NI.23600.047 Mini-card WLAN (3rd WiFi 2x2 BGN) FOXCONN TW W/L CARD 086 T77H047.31 150MBPS HB93 NI.23600.062 Mini-card WLAN (3rd WiFi 2x2 BGN) LITE-ON W/L WN6602AH-AA B853GU210G 300M HB93V046 NI.23600.063 Mini-card WLAN (3rd WiFi 2x2 BGN) LITE-ON ...

  • Packard Bell TM86 - page 206

    196 Appendix B Antenna WIFI/ WIMAX L WNC ANTENNA 0C8 81.EJ T15.GEN WI FI A/L Antenna WIFI/ WIMAX R WNC ANTENNA 0C8 81.EJT1 5.GEM WIFI M/R X WNC ANTENNA 0C8 81.EJT1 5.GEK 3G M/WIFI A Antenna 3G aux+WIFI main+GPS WNC ANTENNA 0C8 81.EJT1 5.GEL 3G A/WIFI M/G Blue T ooth BT Foxconn B_T_ MODU 0C9 FOXCONN T77H1 14.01 BCM2070 BT .21 100.005 BT Foxconn Foxc ...

  • Packard Bell TM86 - page 207

    Appendix B 197 LED 2nd source(IPE X compatible) "MEC,HIGH- TEK,Foxconn "H-CONN SET 0C9 LED LCD- M/B W/ CAMERA 2nd source(IPE X compatible) LED w/o CMOS MEC H-CONN SET 0C9 LED LCD-M/B W/O CAMERA "LED w/o CMOS ""MEC "H-CONN SET 0C9 LED LCD- M/B W/O CAMERA LED With 3G MEC H-CONN SET 0C9 LED LCD-MB W/CAM W/3G H_C "LED ...

  • Packard Bell TM86 - page 208

    198 Appendix B High-T ek H-CONN SET 0C9 M/B-BT Foxconn H-CONN SET 0C9 M/B-BT CardRead/B Humburg FFC 8P H P1 P AD=0.7 187MM CARD READER/ B-M/B Cvilux FFC 8P H P1 P AD =0.7 187MM CARD READER/ B-M/B TP-M/B Humburg FFC 6P G P1 P AD=0.65 1 16MM TP-M/B Cvilux FFC 6P G P1 P AD=0.65 1 16MM TP-M/B USB-M/B Humburg FFC 12P H P1 P AD=0.7 192MM USB-M/B Cvilux F ...

  • Packard Bell TM86 - page 209

    Appendix B 199 Thermal Module (UMA) CCI Delta NEW70_UMA_THM_MAIN_ASSY_Delta_CCI CCI ADDA NEW70_UMA_THM_MAIN_ASSY_ADDA_CCI Robin Delta NEW70_UMA_T HM_MAIN_ASSY_Delta_ROBI N Robin ADDA NEW70_UMA_THM_MAIN_ASSY_ADDA_ROB IN A VC Delta NEW70_UMA_THM_MAIN_ASSY_Delta_A VC A VC ADDA NEW70_UMA_THM_MAIN_ASSY_ADDA_A VC Sunon Sunon NEW70_UMA_T HM_MAIN_ASSY_SUNO ...

  • Packard Bell TM86 - page 210

    200 Appendix B Thermal Sensor ADI S IC ADM1032ARMZ MSOP 8P TEMP SENSOR HD Audio codec REAL TEK S IC ALC272X-GR LQFP 48P CODEC Audio AmPlifier TI S IC TP A6017A2PWPR TSSOP 20P AMP FA N controller ANPEC S IC APL5607KI-TRG SOP 8P Category V end or Description PN ...

  • Packard Bell TM86 - page 211

    Appendix C 201 Online Support Information This section describe s online techni cal support servic es available to help you repair your Acer Systems. If you are a distributor , deal er , ASP or TPM, please re fer your technical que ries to your local Acer branch office. Acer Branch Offices and Regional Business Unit s may access our website. Howeve ...

  • Packard Bell TM86 - page 212

    202 Appendix C ...

  • Packard Bell TM86 - page 213

    203 A AFLASH Utility 32 Antennas Removing 96, 98 Replacing 100 B Battery Replacing 138 Battery Pack Removing 45 BIOS ROM type 16 vendor 16 BIOS Utility 23–32 Advanced 27 Boot 30 Exit 31 Navigating 23 Onboard Device Configur ation 28 Power 30 Save and Exit 31 Security 27 System Security 31 Board Layout Top View 159 C Camera Module Removing 89, 90 ...

  • Packard Bell TM86 - page 214

    204 Replacing 102 LCD Cable Replacing 102 LCD Failure 143 LCD Module Disassembly Flowchart 84 LCD Module Reassembly Procedure 100 LCD Panel Removing 92 Replacing 102 Left S peaker Module Removing 66 Replacing 124 M Main Unit Disassembly Flowchart 58 Mainboard Removing 72, 74, 76, 77 Replacing 114 media access on indicator 10 Memory Replacing 131 Me ...

  • Packard Bell TM86 - page 215

    205 BIOS 23–32 W Windows 2000 Environ ment T est 188 Wireless Function Failure 150 WLAN Module Removing 54 Replacing 130 ...

  • Packard Bell TM86 - page 216

    206 ...

Manufacturer Packard Bell Category Laptop

Documents that we receive from a manufacturer of a Packard Bell TM86 can be divided into several groups. They are, among others:
- Packard Bell technical drawings
- TM86 manuals
- Packard Bell product data sheets
- information booklets
- or energy labels Packard Bell TM86
All of them are important, but the most important information from the point of view of use of the device are in the user manual Packard Bell TM86.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Packard Bell TM86, service manual, brief instructions and user manuals Packard Bell TM86. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Packard Bell TM86.

Similar manuals

A complete manual for the device Packard Bell TM86, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Packard Bell TM86 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Packard Bell TM86.

A complete Packard Bell manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Packard Bell TM86 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Packard Bell TM86, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Packard Bell TM86, that we can find in the current document
3. Tips how to use the basic functions of the device Packard Bell TM86 - which should help us in our first steps of using Packard Bell TM86
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Packard Bell TM86
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Packard Bell TM86 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Packard Bell TM86?

Use the form below

If you did not solve your problem by using a manual Packard Bell TM86, ask a question using the form below. If a user had a similar problem with Packard Bell TM86 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)