English dropdown-ico

Manual Siemens SANTIS-ab

28 pages 0.13 mb
Download

Go to site of 28

Summary
  • Siemens SANTIS-ab - page 1

    User Manual for SANTIS-ab Subscriber Access and Network Termination for ISDN Services ...

  • Siemens SANTIS-ab - page 2

    2 U mains 230VAC / 50Hz LED for local feeding SIEMENS LED for remote feeding a/b1 a/b2 S S ...

  • Siemens SANTIS-ab - page 3

    3 Contents 1. Safety Instructions ..................................................................... 4 2. Operating Modes ....................................................................... 5 3. Installation ................................................................................. 6 4. Configuration .................................. ...

  • Siemens SANTIS-ab - page 4

    4 1. Safety Instructions • Place the SANTIS-ab near a 230 V outlet. • Do not open the case. • Clean the case only with dry or moist cloth. Never immerse into water. • If the SANTIS-ab is damaged, inform immediately your network provider. ...

  • Siemens SANTIS-ab - page 5

    5 2. Operating Modes The connection to the public telephone network as well as the selection of one of the following three operating modes must be done by an authorized person, e.g. telecom staff: 1. NT+2ab S- and a/b-interfaces available 2. NTBA Only S-interface available 3. Pairgain Only a/b-interfaces available ...

  • Siemens SANTIS-ab - page 6

    6 3. Installation • If both the green LEDs light steadily, the SANTIS-ab is ready for operation (see figure on page 2). The following installation-steps can be done by everyone. • The SANTIS-ab can be wall-mounted or placed on the desk (piling of more units is also possible). In case of wall mounting, drill the holes into the wall according to ...

  • Siemens SANTIS-ab - page 7

    7 • Connection of the terminal equipments: The sockets for the analog equipments (e.g. telephones, gr.2/3 fax machines, modems) are designated with «a/b1» and «a/b2», those for the ISDN terminal equipments with «S» (e.g. ISDN-telephones, PC with ISDN-card, gr.4 fax machines). See figure on page 2. ...

  • Siemens SANTIS-ab - page 8

    8 4. Configuration • There are only parameters for the a/b-interfaces. Thus there is only a need for a configuration, if the a/b-interfaces are available ( NT+2ab mode and Pairgain mode; see chapter 2). The configuration remains stored, even after a power failure. • The configuration is done by means of an analog telephone set equipped with ton ...

  • Siemens SANTIS-ab - page 9

    9 If the configuration access (CA) is restricted (can be set and changed by authorized persons, e.g. telecom staff), the configuration for the a/b1-interface can only be done via the a/b1-interface and vice versa for the a/b2-interface. This mode is called NT+2ab/CA restr. If the Pairgain mode is selected, the configuration access is automatically ...

  • Siemens SANTIS-ab - page 10

    10 The settings are executed as follows. See also flow chart on next page. 1. Hook off and wait for dial tone 2. Dial ∗∗ → The dial tone is switched off 3. Dial the command number and parameter value according to the tables in chapter 5. 4. Dial # → If the parameter has been programmed successfully, a permanent tone is switched on. Otherwis ...

  • Siemens SANTIS-ab - page 11

    11 Start: Hook off Dial ∗∗ Input command number Input parameter value Dial # Setting over? End: Hook on no ...

  • Siemens SANTIS-ab - page 12

    12 5. Table of Configuration Commands Parameter-Reset Command-No / Meaning Parameter value Default 010 reset of all parameters to the default value 1 --- All parameters having a default value are affected. The default values are set in the factory and can be reseted by this command. Restrictions for NT+2ab/CA restr. and Pairgain: A parameter reset ...

  • Siemens SANTIS-ab - page 13

    13 Multiple Subscriber Number (MSN) Command-No / Meaning Parameter value Default 111 1st MSN for a/b1 0 to 16 digits --- *) 121 2nd MSN for a/b1 0 to 16 digits 0000 0000 131 3rd MSN for a/b1 0 to 16 digits 0000 0000 112 1st MSN for a/b2 0 to 16 digits --- *) 122 2nd MSN for a/b2 0 to 16 digits 0000 0000 132 3rd MSN for a/b2 0 to 16 digits 0000 0000 ...

  • Siemens SANTIS-ab - page 14

    14 Hot Line Command-No / Meaning Parameter value Default 181 hot line number for a/b1-interface 0-16 digits --- 182 hot line number for a/b2-interface 0-16 digits --- 191 hot line switch for a/b1-interface 0 = hot line off 1 = hot line on 0 192 hot line switch for a/b2-interface 0 = hot line off 1 = hot line on 0 Hot line means that a predefined nu ...

  • Siemens SANTIS-ab - page 15

    15 Emergency Mode Priority Switch Command-No / Meaning Parameter value Default 210 emergency mode priority 0 = S-interface 1 = a/b-interface *) 0 *) First hooked off, first served Emergency mode means failure of the mains. Then only one terminal equipment can be operated at either the S- or one of both the a/b-interfaces. The preferred interface ca ...

  • Siemens SANTIS-ab - page 16

    16 Type of Terminal Selection (HLC) Command-No / Meaning Parameter value Default 221 type of terminal equipment at a/b1-interface (HLC) 0 = audio 1 = telephony 2 = fax gr.2/3 3 = modem(audio) 0 222 type of terminal equipment at a/b2-interface (HLC) 0 = audio 1 = telephony 2 = fax gr.2/3 3 = modem(audio) 0 In order to have all the benefits of an ISD ...

  • Siemens SANTIS-ab - page 17

    17 Clear Back Time Delay Switch Command-No / Meaning Parameter value Default 311 clear back time delay at a/b1-interface 0 = immediate 1 = 3 minutes 1 312 clear back time delay at a/b2-interface 0 = immediate 1 = 3 minutes 1 If you answer a phone call, you can hook on and the connection is still available, if you hook off again within 3 minutes (th ...

  • Siemens SANTIS-ab - page 18

    18 PABX-Switch Command-No / Meaning Parameter value Default 320 address selection 0 = standard 1 = PABX 0 If both the a/b-interfaces are connected to a PABX, this parameter should be set to ‘1’. Restrictions: NT+2ab/CA restr.: Can only be set by authorized persons. Pairgain: Automatically set to ‘1’ and can not be changed. ...

  • Siemens SANTIS-ab - page 19

    19 Metering Pulse Switch Command-No / Meaning Parameter value Default 331 Metering pulses at a/b1-interface 0 = off 1 = on 1 332 Metering pulses at a/b2-interface 0 = off 1 = on 1 Some terminal equipments (e.g. modems) do not work correctly, if metering pulses are sent. Thus it is possible to switch them off. Restrictions for NT+2ab/CA restr. and P ...

  • Siemens SANTIS-ab - page 20

    20 Call Waiting Tone Switch Command-No / Meaning Parameter value Default 341 call waiting tone at a/b1-interface 0 = off 1 = on 1 342 call waiting tone at a/b2-interface 0 = off 1 = on 1 The call waiting tone is a tone in the receiver signaling an incom- ing call during a call is already ongoing. This service is not available at every network provi ...

  • Siemens SANTIS-ab - page 21

    21 Metering Calculation Command-No / Meaning Parameter value Default 380 amount for one metering pulse 1 to 8 digits country specific 390 currency factor 1 to 8 digits country specific Example for US$: 1 pulse = 10 cents, thus dial ∗∗ 380 10 # 1 US$ = 100 cents, thus dial ∗∗ 390 100 # Restrictions for NT+2ab/CA restr. and Pairgain: Can only ...

  • Siemens SANTIS-ab - page 22

    22 Calling Line Identification Restriction (CLIR) Switch Command-No / Meaning Parameter value Default 411 CLIR at a/b1-interface 0 = ident. restr. 1 = ident. allowed 1 412 CLIR at a/b2-interface 0 = ident. restr. 1 = ident. allowed 1 In the ISDN world the number of the caller is submitted to the called party. CLIR means ‘ C alling L ine I dentifi ...

  • Siemens SANTIS-ab - page 23

    23 Configuration Example 1: Priorising a/b-interfaces during emergency mode 1. Hook off and wait for dial tone, then dial 2. ∗∗ → the dial tone is switched off 210 1 # 3. When a permanent tone is switched on, hook on. ...

  • Siemens SANTIS-ab - page 24

    24 Configuration Example 2: A fax machine gr.3 is connected to the a/b1-interface. Thus the MSN and HLC are to be set: MSN = 456, HLC = fax gr.2/3 for a/b1. 1. Hook off and wait for dial tone, then dial 2. ∗∗ → the dial tone is switched off 111 456 # → 1st MSN for a/b1 3. When the permanent tone is switched on proceed to 4 and dial 4. 221 2 ...

  • Siemens SANTIS-ab - page 25

    25 Remarks: • There is a time limitation for the programming. If one sequence is not finished within 30 seconds, an internal generated busy tone will be switched on. • Check if the programming was successful with test calls between two a/b-interfaces or from an ISDN-telephone set to an analog one and vice versa. ...

  • Siemens SANTIS-ab - page 26

    26 6. Troubleshooting 1. Check the green LEDs on the top of the case: both must light steadily. • If the LED designated with ‘local feeding’ is off, check the power cord. • If the LED designated with ‘remote feeding’ is off and remains off for some minutes , inform your network provider. 2. Check the correct connection of the terminal e ...

  • Siemens SANTIS-ab - page 27

    27 7. Pin Allocations of the Sockets Interface Pins a/b1, a/b2 4 & 5 S receive 3 & 6 S transmit 4 & 5 ...

  • Siemens SANTIS-ab - page 28

    Release 1.1 / 07.96 A1608-X6-A-2-7619 USER11.DOC Siemens Switzerland Ltd. ...

Manufacturer Siemens Category Network Card

Documents that we receive from a manufacturer of a Siemens SANTIS-ab can be divided into several groups. They are, among others:
- Siemens technical drawings
- SANTIS-ab manuals
- Siemens product data sheets
- information booklets
- or energy labels Siemens SANTIS-ab
All of them are important, but the most important information from the point of view of use of the device are in the user manual Siemens SANTIS-ab.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Siemens SANTIS-ab, service manual, brief instructions and user manuals Siemens SANTIS-ab. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Siemens SANTIS-ab.

Similar manuals

A complete manual for the device Siemens SANTIS-ab, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Siemens SANTIS-ab by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Siemens SANTIS-ab.

A complete Siemens manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Siemens SANTIS-ab - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Siemens SANTIS-ab, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Siemens SANTIS-ab, that we can find in the current document
3. Tips how to use the basic functions of the device Siemens SANTIS-ab - which should help us in our first steps of using Siemens SANTIS-ab
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Siemens SANTIS-ab
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Siemens SANTIS-ab in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Siemens SANTIS-ab?

Use the form below

If you did not solve your problem by using a manual Siemens SANTIS-ab, ask a question using the form below. If a user had a similar problem with Siemens SANTIS-ab it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)