English dropdown-ico

Manual Logik LDW60S11

36 pages Not applicable
Download

Go to site of 36

Summary
  • Logik LDW60S11 - page 1

    F r e e s t a n d i n g D i s h w a s h e r I n s t a l l a t i o n / I n s t r u c t i o n M a n u a l L D W 6 0 S 1 1 LDW60S11_IB_110331.indd 1 3/31/11 5:09 PM ...

  • Logik LDW60S11 - page 2

    LDW60S11_IB_110331.indd 2 3/31/11 5:09 PM ...

  • Logik LDW60S11 - page 3

    3 C onten ts Unpacking ..................................................................................................................................... 4 Installation .................................................................................................................................... 5 Location .................................. ...

  • Logik LDW60S11 - page 4

    4 Fr ost Precaution ......................................................................................................................... 25 Moving the Dishw asher ............................................................................................................. 25 Maintenance A fter a Prolonged P eriod of Non-Operation ............. ...

  • Logik LDW60S11 - page 5

    5 Unpacking Remove all packaging from the unit. Retain the pack aging . If you dispose of it please do so accor ding to local regulations. The following items ar e included: The Main Unit Detergent Measuring Spoon x 1 1 full spoon = 20g (approx.) P .N.: 673002200079 Instruction Manual X 1 P .N.: LDW60S11-000 U-shape Hose Holder X 1 P .N.: 673006200 ...

  • Logik LDW60S11 - page 6

    6 INST ALL A TION unit in mm level level level level Power Delay Start 1/2 Load 3in1 Intensive Normal Eco Rinse Glass Rapid Power Delay Start 1/2 Load 3in1 Intensive Normal Eco Rinse Glass Rapid 600 580 850 30 850 600 620 min.100 80 600 580 850 30 850 600 620 min.100 80 1. Please ensure the dishwasher is installed by a qualified technician. Refer t ...

  • Logik LDW60S11 - page 7

    7 INST ALL A TION 4. The condensation str ip must be fitted to the underside of the worktop above your dishwasher to protect it against an y moisture. Its purpose is to protect your w orktop ’ s underside from steam rising from the dishwasher . • Ensure the surface is clean prior to stick ing the condensation strip to the underside of the wo ...

  • Logik LDW60S11 - page 8

    8 INST ALL A TION 7. Make sure your plumbing is suitable for use with the dishwasher . If in doubt contact a qualified plumber . This unit MUST BE connected to C OLD W A TER MAINS using the new water inlet hose. OLD HOSE SETS MUST NOT BE RE-USED. The water pressure from the water mains needs to be at a minimum of 0.04 MPa and a maximum of 1.00MPa. ...

  • Logik LDW60S11 - page 9

    9 INST ALL A TION water drain hose U-shaped drain hose holder • Y ou may use the U-shaped drain hose holder to secure your drain hose and to avoid bending it. • Secure the water drain hose to the waste pipe to av oid it coming off during the washing process. The waste pipe must only be connected to the foul drains and not the sur face wat ...

  • Logik LDW60S11 - page 10

    10 Pr oduc t Overview Fr ont Vie w Rear View 1. Control P anel 2. Door Handle Power Delay Start 1/2 Load 3in1 Intensive Normal Eco Rinse Glass Rapid 2 3 1 5 4 3. Drain Hose 4. W ater Inlet (Connect T o Supply Hose) 5. Mains Cable (Connect T o Electrical Mains Outlet) LDW60S11_IB_110331.indd 10 3/31/11 5:09 PM ...

  • Logik LDW60S11 - page 11

    11 Upper Basket Internal Vie w Low er Basket 6 10 7 11 8 12 9 13 6. Upper Basket 7. Salt R eservoir 8. Low er Basket 9. Detergent Dispenser 10. Cup Rack 11. Spray Arms 12. F iltering System 13. Rinse Aid Reservoir LDW60S11_IB_110331.indd 11 3/31/11 5:10 PM ...

  • Logik LDW60S11 - page 12

    12 1. ON / OFF Button • T o turn the dishwasher on and off. 2. Power On Light • Illuminates when On/Off button is pressed. 3. Display W indow ( Con trol Panel) • Prog ramme remaining time , delay time and fault codes etc . 4. Delay Start Button • Press to preset the wash timer and delay the starting time by up to 24 hours. •? ...

  • Logik LDW60S11 - page 13

    13 W ash C y cle T able Programme C ycle Selec tion Information Process Detergent Amount (Pre-wash/ Main wash) Running Time (min.) Energy Consumption (K wh) W ater Consumption (I) Rinse Aid 3 I n 1 • P ots, utensils and cutler y . • Highly soiled. • Pr e -wash (50°C) • W ash (50°C ) • Rinse (70°C ) • Drying • 3 ...

  • Logik LDW60S11 - page 14

    14 ● ● Small plastic items (Milk bottle nipple) Plastic items that are not dishwasher safe Crystal glasses Silverware V aluable vases Copper pots and pans Cast iron pans Cracked / Chipped china Scratched non-stick cookware T owels and sponges The Following Items Are Not Suitable Before Oper ating T o Open the Door • Pull the door handle. ? ...

  • Logik LDW60S11 - page 15

    15 Y ou can choose to add a detergent tablet alone or to add deter gent powder to both the main wash detergent chamber and the pre -wash detergent chamber for your selected wash cycle. All prog rammes with pre-wash need an additional detergent dosage that must be placed in the pre-wash deter gent chamber (please refer to the wash cycle table). This ...

  • Logik LDW60S11 - page 16

    16 Alternatively , you can judge the amount of rinse aid by check ing the r inse aid indicator right next to the reservoir ’ s cap . When the indicator is black, it means it is full . When it is clear , it means it is almost empty. Adjusting the Rinse Aid Reservoir The rinse aid reservoir has six settings . Both the recommended setting and the fa ...

  • Logik LDW60S11 - page 17

    17 Adding Salt If the water in your area is hard, deposits will form on your dishes and utensils. This appliance con tains a salt reser voir for you to reduc e the hardness of the water . Please follow the steps below to pour the salt into the salt reservoir and it must be set to correspond to the water hardness level in your area. 1. Remove the lo ...

  • Logik LDW60S11 - page 18

    18 Adjusting Salt C onsumption Salt consumption must be adjusted to correspond to the water hardness lev el in your area. I f you don’ t know how hard the wa ter in your home is, please ask the company that supplies water in your area. It is recommended that adjustments should be made in accor dance with the following char t. W ater Hardness Sele ...

  • Logik LDW60S11 - page 19

    19 Loading the Dish washer Before L oading the Dishwasher Please obser ve the following notes befor e loading your cutler y and crocker y into the basket. • Remove lipstick stains and any f ood residues from crockery and dishes. Rinse if necessar y . • Dishes and cutlery must not lay inside one another , or cover each other . • Load ...

  • Logik LDW60S11 - page 20

    20 Long items such as soup ladles, mixing spoons and long knives should be placed lying down across the front of the upper basket. Upper Basket Please use the upper basket for small and lightweight items such as cups, saucers, glasses, desser t bowls, etc. Shallow pans or casserole dishes can also be placed in the upper basket. remove the stop lift ...

  • Logik LDW60S11 - page 21

    21 Low er Basket W e recommend that large and the most difficult to clean items are placed in the lower basket, such as plates, ser ving platters, saucepans, serving bowls, pots, pans, lids etc. W e recommend placing serving dishes and lids at the side of the basket to av oid block ing the rota tion of the spray arms. Hinged Cup Rack T o make room ...

  • Logik LDW60S11 - page 22

    22 Loading the Low er Basket F or loading the lower basket, please refer to the table below. Number Item 7 Desser t dishes 8 Oval platter 9 Dinner plat es 10 Soup plates 11 Cutlery basket Cutlery Basket Loading the C utlery B ask et T o make unloading much easier , cutlery should be grouped in zones and placed in the cutler y basket. Please refer t ...

  • Logik LDW60S11 - page 23

    23 Star ting a W ash C ycle Please follow the steps below to start a wash c ycle . 1. Ensure the unit is connec ted to the mains power and the water supply is on (water pressur e bet w een 0.04MPa and 1.00MPa). 2. Open the door . P ull out the lower and upper baskets, load the dishes and push the baskets back. I t is recommended that the lower bask ...

  • Logik LDW60S11 - page 24

    24 S witching O the Unit T o save energy, remember to switch the dishwasher off using the ON/OFF button. The dishwasher will continue to use electricity until it is switched off with the ON/OFF button. If the dishwasher is not going to be used f or a long period of time, e.g. whilst on holiday , disconnec t the unit from the mains supply. Unload ...

  • Logik LDW60S11 - page 25

    25 Internal Car e Filtering S ystem The filtering system in the base of the wash cabinet captures large par ticles of suds solution. Build up of these par ticles may cause the filters to block. Check the condition of the filters regularly and clean them if necessary under running wat er . F ollow the steps below to clean the filters in the wash cab ...

  • Logik LDW60S11 - page 26

    26 Spra y Arms Particles of food can get stuck in the spray arm jets and bearings. T he spray arms should ther efore be checked and cleaned regularly. • Use a pointed object, eg . a cocktail stick, to loosen f ood particles in the spray arms’ jets. F rost P recaution Av oid placing the dishwasher in a location where the temperature is below ...

  • Logik LDW60S11 - page 27

    27 Hints and Tips F ault Code Codes Possible Causes Remedy E1 W ater tap is not turned on. T urn on the water tap. Low water pressure (<0.04MPa) T urn on the water tap and ensure it is in full position. Flow meter is broken. • Disconnect from the mains. • Disconnect the water inlet. • Call a qualified technician. The wire terminal ...

  • Logik LDW60S11 - page 28

    28 General Problems Problem Possible Causes Remedy Detergent residue is left in the dispenser at the end of the programme . The detergent dispenser was still damp when detergent was added. Make sure the dispenser is dr y before adding detergent. The detergent dispenser lid cannot be closed properly . Clogged detergent residue is blocking the catch. ...

  • Logik LDW60S11 - page 29

    29 Disposal of the Dishw asher • When disposing your old dishwasher , first make it unusable. Disconnect the hoses and unplug the mains cable. C ut off the mains cable from the dishwasher . Make the door lock inoperative, so that children cannot accidentally shut themselves in. Make appropriate arrangements for the disposal of the dishwasher . ...

  • Logik LDW60S11 - page 30

    30 Specications Model LDW60S11 Dimensions 600 mm ( W ) x 580 mm (D) x 850 mm (H) Capacity 12 Place Settings W ater Pressure Required 0.04 - 1.00MP a Po wer Consumption 1930W Rated V oltage 230V/50Hz F eatures and specifications are subject to change without prior notice . LDW60S11_IB_110331.indd 30 3/31/11 5:10 PM ...

  • Logik LDW60S11 - page 31

    31 Safety W arnings F or your continued safety and to reduce the risk of injur y or electric shock, please follow all the safety precautions listed below. • Read all instructions carefully befor e using the dishwasher and keep them for future referenc e. • Retain the manual. If you pass the dishwasher onto a third party, make sur e to inc ...

  • Logik LDW60S11 - page 32

    32 • F or energy saving , always remember to switch the dishwasher off when you have finished using it. T he dishwasher should not be lef t unattended when in use. • Remove the door to the washing compartment when removing an old dishwasher from ser vice or discarding it. • During installation, the power supply cord must not be exces ...

  • Logik LDW60S11 - page 33

    NOTE: If you requir e a replacement for any of the items listed below , please quote their corresponding part numbers: Replacement Part Part Number Cutlery Basket 673002200099 W ater Supply Hose 673000900060 Detergent Measuring Spoon 673002200079 Measuring C up 673006200004 Condensation Strip 675001300715 Salt Funnel 673002200043 U-shape Hose Holde ...

  • Logik LDW60S11 - page 34

    LDW60S11_IB_110331.indd 34 3/31/11 5:10 PM ...

  • Logik LDW60S11 - page 35

    LDW60S11_IB_110331.indd 35 3/31/11 5:10 PM ...

  • Logik LDW60S11 - page 36

    LDW60S11_IB_110331.indd 36 3/31/11 5:10 PM ...

Manufacturer Logik Category Dishwasher

Documents that we receive from a manufacturer of a Logik LDW60S11 can be divided into several groups. They are, among others:
- Logik technical drawings
- LDW60S11 manuals
- Logik product data sheets
- information booklets
- or energy labels Logik LDW60S11
All of them are important, but the most important information from the point of view of use of the device are in the user manual Logik LDW60S11.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Logik LDW60S11, service manual, brief instructions and user manuals Logik LDW60S11. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Logik LDW60S11.

Similar manuals

A complete manual for the device Logik LDW60S11, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Logik LDW60S11 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Logik LDW60S11.

A complete Logik manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Logik LDW60S11 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Logik LDW60S11, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Logik LDW60S11, that we can find in the current document
3. Tips how to use the basic functions of the device Logik LDW60S11 - which should help us in our first steps of using Logik LDW60S11
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Logik LDW60S11
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Logik LDW60S11 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Logik LDW60S11?

Use the form below

If you did not solve your problem by using a manual Logik LDW60S11, ask a question using the form below. If a user had a similar problem with Logik LDW60S11 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)