English dropdown-ico

Manual Husqvarna 15V2 AWD

36 pages 2.28 mb
Download

Go to site of 36

Summary
  • Husqvarna 15V2 AWD - page 1

    E E E E n n n n g g g g l l l l i i i i s s s s h h h h Rider 15V2 Rider 15V2 A WD Oper ator ′ s manual Please r ead the operator’ s manual carefull y and make sur e you understand the instructions before using the machine. ...

  • Husqvarna 15V2 AWD - page 2

    2 – English CONTENTS Contents CONTENTS Contents ...................................................................... 2 Ser vice journal Pre-deliv er y ser vice ..................................................... 3 After the first 8 hours ................................................... 3 INTR ODUCTION Dear Customer , ..................... ...

  • Husqvarna 15V2 AWD - page 3

    English – 3 Ser vice journal Pre-deliver y service 1 T op up batter y with acid and charge for f our hours. 2 Fit steering wheel, seat and any optional equipment. 3 Adjust cutting unit: Adjust lift springs (effectiv e weight of cutting unit should be 12-15kg / 26.5-33 lb). Adjust cutting unit so that rear edge is about 2-4 mm / 1/8” higher than ...

  • Husqvarna 15V2 AWD - page 4

    4 – English INTR ODUCTION Dear Customer , Thank y ou f or choosing a Husqvarna Rider . Husqvarna Riders are built to a unique design with a front-mounted cutting unit and a patented rear-wheel steering system. Riders are designed for maximum efficiency e ven in small or confined areas. The closely grouped controls and pedal-operated h ydrostati ...

  • Husqvarna 15V2 AWD - page 5

    English – 5 INTR ODUCTION Good ser vice Husqv arna products are sold all over the world and only through servicing dealers. This is to ensure that you, the customer , get the best suppor t and ser vice. For e xample, bef ore this machine was deliv ered it was inspected and adjusted b y your dealer . See the cer tificate in the Ser vice Jour nal ...

  • Husqvarna 15V2 AWD - page 6

    6 – English KEY T O SYMBOLS Symbols These symbols are on the machine and in the instr uctions. W ARNING! Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the oper ator’ s manual carefully and make sure y ou understand the instructions before using the machine . Alw a ys wear: • Approv ed h ...

  • Husqvarna 15V2 AWD - page 7

    English – 7 KEY T O SYMBOLS Switch off the engine and take off the ignition cable bef ore repairs or maintenance Check the engine’ s oil le vel Check the h ydrostat’ s oil lev el Lift up the cutting unit Apply the par king brak e. If the engine is cold, use the choke Release the parking brake bef ore dr iving ...

  • Husqvarna 15V2 AWD - page 8

    8 – English SAFETY INSTR UCTIONS Safety instructions These instructions are for y our saf ety . Read them carefully . Insure y our Rider • Check the insur ance cov erage f or your ne w Rider. • Contact your insur ance company . • Y ou should hav e fully comprehensive insurance including: third par ty , fire, damage, theft and liability Gen ...

  • Husqvarna 15V2 AWD - page 9

    English – 9 SAFETY INSTR UCTIONS • Ne ver allo w children or other persons not trained in the use of the machine to use or ser vice it. Local laws ma y regulate the age of the user . • Use hearing protection to minimise the r isk of hearing impairment. • W ear approv ed protective glasses or full-f ace visor dur ing assembly and when oper a ...

  • Husqvarna 15V2 AWD - page 10

    10 – English SAFETY INSTR UCTIONS • Do not tr y to stabilize the machine b y putting your f oot on the ground. • When cleaning the chassis, the machine ma y nev er be driven near v erges or ditches. • F ollow the manuf acturer’ s recommendations regarding wheel weights or counterbalance weights to increase machine stability . Children • ...

  • Husqvarna 15V2 AWD - page 11

    English – 11 SAFETY INSTR UCTIONS • Be especially careful when handling batter y acid. Acid on the skin can cause serious corrosive injuries. In the e vent of spillage on the skin wash immediately with w ater . • Acid in the ey es can cause blindness , contact a doctor immediately . • T ake care with battery maintenance. Explosive gases f o ...

  • Husqvarna 15V2 AWD - page 12

    12 – English WHA T IS WHA T? Location of the controls 4 5 6 10 12 13 7 32 14 11 9 8 1 1 Choke control 2 Throttle control 3 Ignition lock 4 Cutting height adjustment le ver 5 Lifting le ver f or the cutting unit 6 Speed limiter f or rev ersing 7 Speed limiter f or driving forward 8 P arking brake 9 Lock b utton f or parking brake 10 Seat adjustmen ...

  • Husqvarna 15V2 AWD - page 13

    English – 13 PRESENT A TION Presentation Cong ratulations on y our choice of an e xcellent quality product that will give y ou great pleasure for man y years . This operator’ s manual describes Rider 15V2 and Rider 15V2 AW D. The machines are equipped with a 15 horse power engine from Kaw asaki. Rider 15V2 A WD is equipped with all wheel dr ive ...

  • Husqvarna 15V2 AWD - page 14

    14 – English PRESENT A TION The Combi-unit, equipped with a BioClip-plug, finely chops the cuttings to f er tiliser . Without the BioClip-plug the unit works in the same wa y as a rear ejection unit. Lifting lever f or the cutting unit The lift le ver is used to set the cutting unit in tr anspor t or mowing position. If the le ver is pulled bac ...

  • Husqvarna 15V2 AWD - page 15

    English – 15 Driving Bef ore star ting • Read the saf ety instructions and information concer ning the placement of controls and functions bef ore star ting. • P erform daily maintenance before starting as set out in the Maintenance schedule. Star t the engine 1 Make sure that the clutch control is depressed. Rider 15V2 A WD has one control f ...

  • Husqvarna 15V2 AWD - page 16

    16 – English Driving 8 Let the engine run at moderate speed or half throttle for 3- 5 minutes bef ore subjecting it to heavy load. 9 Set the required engine speed with the throttle control. Star ting the engine with a weak battery If the batter y is too weak to star t the engine, it should be recharged. When jump leads are used f or emergency sta ...

  • Husqvarna 15V2 AWD - page 17

    English – 17 Driving 4 Press in the lock b utton on the lifting le ver and lo wer the cutting unit. Cutting tips • Localise and mark stones and other fixed objects to a void collision. • Star t with a high cutting height and reduce down until the required mowing results are obtained. • The mowing results are best with a high engine speed ( ...

  • Husqvarna 15V2 AWD - page 18

    18 – English Driving Release lever The release control must be pulled out in order f or the machine to be mov ed when the engine is shutoff . Pull the controls to the end positions, do not use an intermediate position. Release lever Rider 15V2 A WD Rider 15V2 A WD has one control for the front axle and one control f or the rear axle. • Clutch c ...

  • Husqvarna 15V2 AWD - page 19

    English – 19 Maintenance Maintenance schedule The f ollowing is a list of the maintenance which should be conducted on the machine. For those points not described in this manual, visit an authorised ser vice workshop. 1) If the machine is used daily it should be lubricated twice a week. 2) Maintenance and replacement are required more often in du ...

  • Husqvarna 15V2 AWD - page 20

    20 – English Maintenance Cleaning Clean the machine directly after use. It is much easier to wash off grass cuttings bef ore they dr y . Oily dir t can be remov ed using a cold degreasing agent. Spra y on a thin la yer . Rinse at normal water pressure. Do not direct the jet tow ards electrical components or bearings. Do not rinse hot surfaces suc ...

  • Husqvarna 15V2 AWD - page 21

    English – 21 Maintenance 1 Remov e the frame plate b y loosening the screws (2) and lift the frame plate b y the rear edge. 2 Check the tension of the steering wires by squeezing them together by the arro ws as illustrated. It should be possible to push them together so that the distance between them is half as much, without using unnecessary f o ...

  • Husqvarna 15V2 AWD - page 22

    22 – English Maintenance 1 Loosen the clamping screw f or the cable’ s outer casing and mov e the throttle to the full throttle position. 2 Check that the throttle wire is attached to the correct hole in the lower le ver , see diagram. 3 Pull the throttle wire casing to the f ar left and tighten the clamping screw . Checking and adjusting the c ...

  • Husqvarna 15V2 AWD - page 23

    English – 23 Maintenance 6 If the paper filter is still dir ty it should be replaced with a new one . Alwa ys replace the paper filter ev er y 200 hours. 7 Put the pre-filter and paper filter back into the air filter unit. 8 Put back the air filter unit b y first aligning the hooks on the bottom of the unit, then press it until the catches ...

  • Husqvarna 15V2 AWD - page 24

    24 – English Maintenance Check the saf ety system The machine is equipped with a saf ety system that pre vents starting or dr iving under the follo wing conditions. The engine should only be possible to start when the cutting unit is in its raised position and the hydrostat pedals are in the neutr al position. The driver does not need to be seate ...

  • Husqvarna 15V2 AWD - page 25

    English – 25 Maintenance Main fuse The main fuse is placed in a detachable holder under the batter y case’ s cover , in front of the batter y . T ype: Flat pin, 15 A. Do not use any other type of fuse when replacing. A blo wn fuse is indicated by a b urnt connector . Pull the fuse from the holder when replacing. The fuse is there to protect the ...

  • Husqvarna 15V2 AWD - page 26

    26 – English Maintenance Mak e sure the support wheels are fitted to the cutting unit (1). 2 Grasp the handle at the front or hold the frame of the cutting unit (2) and slide the unit underneath the r ider mower . Make sure that the tongue (3) on the cutting unit engages correctly . 3 Inser t the bolt and secure it with a locking pin. 4 Press do ...

  • Husqvarna 15V2 AWD - page 27

    English – 27 Maintenance 2 Place the machine on a flat surf ace. 3 Put the lifting le ver in the mo wing position. 4 Place a set of bathroom scales under the cutting unit’ s frame (front edge) so that it rests on the scales. If necessar y a bloc k can be placed between the frame and scales so that the suppor t wheels do not bear any weight. 5 ...

  • Husqvarna 15V2 AWD - page 28

    28 – English Maintenance 3 Loosen the spring (4) that tensions the V -belt and pr y off the belt. Simply re verse the procedure to fit the ne w belt. Service position for the cutting unit The cutting head can be placed in the service position to provide easy access f or cleaning, repairs and ser vicing. In the ser vice position the cutting unit ...

  • Husqvarna 15V2 AWD - page 29

    English – 29 Maintenance 7 Engage the strut in the holder . 8 Lift of the drive belt. Then pull out the pin. 9 Pull the frame f orwards and refit the pin. 10 Grasp the front edge of the cutting unit, pull out and raise into the ser vice position. If the cylindrical bolt, which is now holding the cutting unit is remov ed, the cutting unit can be ...

  • Husqvarna 15V2 AWD - page 30

    30 – English Lubrication Checking the engine’ s oil level. Check the oil le vel in the engine when the Rider stands horizontal with the engine s witched off. Open the engine cov er . Loosen the dipstick, pull it up and wipe it off . Now insert the dipstick again, without tightening it. Pull the dipstick out again and read the oil le vel. The oi ...

  • Husqvarna 15V2 AWD - page 31

    English – 31 Lubrication Fill with new oil according to Chec king the engine’ s oil lev el. Star t the engine and let it idle for about 3 min utes. Now stop it and check f or signs of leakage. Fill with oil to compensate f or the oil held in the new oil filter . Checking the transmission oil le vel 1 Remov e the transmission co ver . Undo the ...

  • Husqvarna 15V2 AWD - page 32

    32 – English T roub leshooting sc hedule Prob lem Procedure Engine does not star t There is no fuel in the fuel tank Spark plug defectiv e F aulty spar k plug connections or interchanged cables Dir t in the carburettor or fuel line Star ter motor does not tur n ov er the engine Star ter motor does not tur n ov er the engine Batter y flat Bad con ...

  • Husqvarna 15V2 AWD - page 33

    English – 33 Storage Winter stora ge At the end of the season, or if the machine is going to stand idle f or more than 30 days , it should immediately be made ready f or storage. Fuel which is left to stand for long periods (30 da ys or more) can leav e tacky deposits which can b lock the carburettor and interf ere with the engine. Fuel stabilise ...

  • Husqvarna 15V2 AWD - page 34

    34 – English T echnical data ´®z+R?6¶6@¨ ´®z+R?6¶6@¨ Dimensions Rider 15V2 Rider 15V2 A WD Length without cutting unit, mm/ft 2020/6,61 2020/6,61 Width without cutting unit, mm/ft 880/2,89 880/2,89 Height, mm/ft 1070/3,52 1070/3,52 Operating weight with cutting dec k, kg/lb 268-274/591-604 302-308/666-679 Wheel base, mm/ft 855/2,8 855/2,8 ...

  • Husqvarna 15V2 AWD - page 35

    English – 35 T echnical data EC-declaration of conf ormity (Applies to Europe onl y) Husqv arna AB, SE-561 82 Huskv ar na, Sweden, tel.: +46-36-146500, hereby declares that Husqv ar na Rider 15V2 and Rider 15V2 A WD from 2005’ s serial numbers and onwards (the year is clearly stated in plain te xt on the rating plate with subsequent serial numb ...

  • Husqvarna 15V2 AWD - page 36

    ´®z+R?6¶6@¨ 2006-10-21 ´®z+R?6¶6@¨ 1150312-26 ...

Manufacturer Husqvarna Category Lawn Mower

Documents that we receive from a manufacturer of a Husqvarna 15V2 AWD can be divided into several groups. They are, among others:
- Husqvarna technical drawings
- 15V2 AWD manuals
- Husqvarna product data sheets
- information booklets
- or energy labels Husqvarna 15V2 AWD
All of them are important, but the most important information from the point of view of use of the device are in the user manual Husqvarna 15V2 AWD.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Husqvarna 15V2 AWD, service manual, brief instructions and user manuals Husqvarna 15V2 AWD. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Husqvarna 15V2 AWD.

Similar manuals

A complete manual for the device Husqvarna 15V2 AWD, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Husqvarna 15V2 AWD by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Husqvarna 15V2 AWD.

A complete Husqvarna manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Husqvarna 15V2 AWD - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Husqvarna 15V2 AWD, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Husqvarna 15V2 AWD, that we can find in the current document
3. Tips how to use the basic functions of the device Husqvarna 15V2 AWD - which should help us in our first steps of using Husqvarna 15V2 AWD
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Husqvarna 15V2 AWD
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Husqvarna 15V2 AWD in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Husqvarna 15V2 AWD?

Use the form below

If you did not solve your problem by using a manual Husqvarna 15V2 AWD, ask a question using the form below. If a user had a similar problem with Husqvarna 15V2 AWD it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)