English dropdown-ico

Manual Dymo Labelmaker M1011

16 pages 2.36 mb
Download

Go to site of 16

Summary
  • Dymo Labelmaker M1011 - page 1

    U ser Guide www .dymo.c om ...

  • Dymo Labelmaker M1011 - page 2

    2 A T ape cassette door H Character selection window B T ape rollers I Cutting han dle C T ape advance knob J Embossing adjustme nt screw D Start line K Cable tie slot punch E T ape pawl L Hole punch F Embossing handle M Cutting assembly G Embossing wheel N Leader/trailer length gui de A B C D F G H I K L M J N E ...

  • Dymo Labelmaker M1011 - page 3

    3 About Y our New Labelmaker With yo ur new DY MO M101 1 labelmaker , you can c reate a wide variety of plas tic an d meta l l abels. The labelmaker uses DYMO 12 mm (1/2" ) label tape. DYMO plasti c tapes are availab le in a wide variety of colors. Metal tapes are available as f ollows: • Aluminium with adhesive (35 800) • Aluminium withou ...

  • Dymo Labelmaker M1011 - page 4

    4 Loading the Labe l T ape The DYMO M101 1 is set to emboss non-adhesive aluminium or plastic tape. T o load the t ape r oll 1. Hold the labelmaker in your left hand. 2. O pen t ape do or (A ). 3. Inse rt roll of tape allowing th e end to exte nd about 5 cm (2 ") through the t ape slot. 4. Close the tape door . 5. Feed th e tape between t he t ...

  • Dymo Labelmaker M1011 - page 5

    5 Cutting the T ape T o cut th e tape 1. Squeeze the emb ossin g handle half-way , several times un til the tape ext ends from th e front of the cutting assemb ly (M) by at least 1 cm (1" ). Before cutting the ta pe, make sure the end of the tape exten ds beyond the edge of the cutting assembly so you can easily pull the label ou t. Otherwise, ...

  • Dymo Labelmaker M1011 - page 6

    6 Embos sing th e Labe l A void turn ing the embossing wheel at the same t ime you are squeez ing the emboss ing h andle. This can da mage the character blades. T o emboss a label 1. T urn the character se lect ion wheel (G) until the desired lett er is centered in the window (H). 2. Squeez e the embossin g handle (F) firmly . 3. Rele ase the embos ...

  • Dymo Labelmaker M1011 - page 7

    7 Emboss ing on Stainless Ste el T a pe Y ou may n eed t o adjust t he labelma ker to emboss properly when usin g stainle ss steel ta pe. T o adjust fo r stainless steel tape 1. T urn the adjus tment scre w (J) clock wise 1/2 t o 3/4 t urn. 2. Emboss the te xt a s describe d in “Embossi ng th e Label” on page 6. When you re turn to using plasti ...

  • Dymo Labelmaker M1011 - page 8

    8 Retracting the T ape Y ou may want to retract the tape, fo r exam ple, if the tape adv anced too fa r or to center the tex t on the la bel. T o retract the tape 1. Pull bac k the pawl (E). 2. T urn the tape advance knob (C) counter-cloc kwise. E C ...

  • Dymo Labelmaker M1011 - page 9

    9 Removing th e T a pe T o remove the tape 1. Retract the t ape a s describe d in “Retrac ting the T ape” on page 8. 2. Open the tape cassett e door (A) and remove the tape. Use ca ution when removing stainless steel t ape that may have sha rp edges. 3. Relo ad th e tape as d escribe d in “Loading the Label T ape” on page 4. A ...

  • Dymo Labelmaker M1011 - page 10

    10 Centering t he T e xt on the Label The leader/tra iler lengt h guide (N) has position ing mark s for a short (S) or long label (L). Use th e marks on the guide to center th e text on your labe l. T o cente r the text on a lo ng label 1. After cu tting th e previous label , emboss the text on a new la bel. 2. Pull th e leader/trailer le ngth guid ...

  • Dymo Labelmaker M1011 - page 11

    11 Applying Self -Adhesive Labels Self-adhes ive plasti c and aluminum labels stick perman ently to any smooth , clean, and dry surface . T o apply self-adhe sive l abels 1. Peel of f the protect ive backing ta king care not to touch the adhes ive. 2. Press the label in place. 3. Apply firm pressure along t he entire length to ensure good contact . ...

  • Dymo Labelmaker M1011 - page 12

    12 Punching Holes in Non-Adh esive Labels Y ou can choos e to punch one or two holes in no n-adhes ive labels so that the la bels can be attached using screws, nails, rivets, and metal or plastic wires or ties. Y ou can al so punc h a cable tie slot in one or both ends of t he label. T o punch a hole 1. Inse rt one end of the cut label into the ho ...

  • Dymo Labelmaker M1011 - page 13

    13 Changing the Wheel Y ou can repla ce the character whee l with a Reverse Ima ge Wheel. T o change the wheel 1. Remove t he label tape. 2. Unscrew the screw in the center of the embossin g wheel (G) and remove the wheel. 3. Position the new wheel. 4. Inse rt the screw in the cente r and tighte n. Do not tigh ten the screw too tightly . G ...

  • Dymo Labelmaker M1011 - page 14

    14 Hints for T rouble Free Operation Keep t he follo wing in mind whe n using the labelmake r: • Lett ers appear where you want spaces - Y ou are probably squee zing the emboss ing handle too hard. • Letters ove rlap - The tape is slipp ing. This can happ en when dirt or grease gets on the rollers. Clean t he rollers by us ing a soft cloth and ...

  • Dymo Labelmaker M1011 - page 15

    Contacting Customer Support The following tab le pr ovides a li st o f tele phone numbe rs to reach DYMO Sal es and Supp ort depa rtme nts. Y ou can also reach DYMO a t www .dymo.com . Country Telephone Support Fax Support Australia 1 800 633 868 1 800 817 558 Austria 01 599 14 20 12 02 6 27 400 160 Belgium 02 713 38 08 +31 20 581 93 80 Canada 800 ...

  • Dymo Labelmaker M1011 - page 16

    W arran ty Registrati on This DY MO M101 1 has been m anufactu red under str ict quality cont rol and p erforman ce tested before leaving the factory . Within one year a fter purchase, DYMO will re pair or repla ce, at its own opti on, the M101 1 free of charge if sent prepai d by the purchaser to DYMO an d fo und, in DYMO's judgeme nt, t o be ...

Manufacturer Dymo Category Printer

Documents that we receive from a manufacturer of a Dymo Labelmaker M1011 can be divided into several groups. They are, among others:
- Dymo technical drawings
- Labelmaker M1011 manuals
- Dymo product data sheets
- information booklets
- or energy labels Dymo Labelmaker M1011
All of them are important, but the most important information from the point of view of use of the device are in the user manual Dymo Labelmaker M1011.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Dymo Labelmaker M1011, service manual, brief instructions and user manuals Dymo Labelmaker M1011. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Dymo Labelmaker M1011.

Similar manuals

A complete manual for the device Dymo Labelmaker M1011, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Dymo Labelmaker M1011 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Dymo Labelmaker M1011.

A complete Dymo manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Dymo Labelmaker M1011 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Dymo Labelmaker M1011, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Dymo Labelmaker M1011, that we can find in the current document
3. Tips how to use the basic functions of the device Dymo Labelmaker M1011 - which should help us in our first steps of using Dymo Labelmaker M1011
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Dymo Labelmaker M1011
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Dymo Labelmaker M1011 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Dymo Labelmaker M1011?

Use the form below

If you did not solve your problem by using a manual Dymo Labelmaker M1011, ask a question using the form below. If a user had a similar problem with Dymo Labelmaker M1011 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)