English dropdown-ico

Manual Henny Penny OFE/OFG-324

29 pages 3.08 mb
Download

Go to site of 29

Summary
  • Henny Penny OFE/OFG-324 - page 1

    Model OFE/OFG-321,322,323,324 SECTION 2. MAINTENANCE 2-1. INTRODUCTION This section provides procedures for the checkout and replacement of the various parts used within the fryer. Before replacing any parts, refer to the Troubleshooting Section. It will aid you in determining the cause of the malfunction. 2-2. MAINTENANCE HINTS 1. You may need to ...

  • Henny Penny OFE/OFG-324 - page 2

    Model OFE/OFG-321,322,323,324 2-3 HIGH TEMPERATURE LIMIT CONTROL (Continued) 3. Remove the two nuts securing the high limit bracket to the unit and pull the bracket from the unit. 4. Remove the two screws securing the high limit to the bracket, and remove the high limit from the bracket. 5. Remove the two electrical wires from the high tem perature ...

  • Henny Penny OFE/OFG-324 - page 3

    Model OFE/OFG-321,322,323,324 2-3 HIGH TEMPERATURE LIMIT CONTROL (Continued) 5. Remove the bracket from the heat tube covering the high lim it bulb. 6. Straighten the capillary tube behind the pot wall. 7. Pull the high limit bulb through the retainers on the heat tube. 8. Remove the larger outside nut that threads into the pot wall. 9. Remove the ...

  • Henny Penny OFE/OFG-324 - page 4

    Model OFE/OFG-321,322,323,324 2-4. COMPLETE CONTROL PANEL REPLACEMENT Should the control board become inoperative, follow these instructions for replacing the board. 1. Remove electrical power supplied to the unit. To avoid electrical shock or property damage, move the POWER switch to OFF and disconnect main circuit breaker, or unplug cord at wall ...

  • Henny Penny OFE/OFG-324 - page 5

    Model OFE/OFG-321,322,323,324 2-5. POWER SWITCH (Continued) 4. With control panel removed, and the wires off the switch, push in on tabs on the switch to remove from panel. 5. Replace with new switch, and reconnect wires to switch. 6. Replace the control panel. 2-6. TEMPERATURE PROBE The temperature probe relays the actual shortening tem perature t ...

  • Henny Penny OFE/OFG-324 - page 6

    Model OFE/OFG-321,322,323,324 2-6. TEMPERATURE PROBE REPLACEMENT (Continued) ELECTRIC GAS 2-6 606 ...

  • Henny Penny OFE/OFG-324 - page 7

    Model OFE/OFG-321,322,323,324 2-6. TEMPERATURE PROBE 7. Tighten the compression nut hand tight and then a half turn REPLACEMENT with wrench. (Continued) Excess force will damage temperature probe. 8. Connect new temperature probe to PC board and replace control panel. 9. Replace shortening. 10. Turn power on and check out fryer. 606 2-7 ...

  • Henny Penny OFE/OFG-324 - page 8

    Model OFE/OFG-321,322,323,324 2-7. FLAME SENSOR The flame sensor recognizes the pilot flame and allows gas to (Gas Units) continue to the pilot. The flame sensor must send a m inimum of two (2) micro amps to the ignition m odule. The pilot flame should be split in two by the flame sensor, causing the flam e sensor to be bright red in color. 1. Remo ...

  • Henny Penny OFE/OFG-324 - page 9

    Model OFE/OFG-321,322,323,324 2-8. PILOT / IGNITOR The Henny Penny open fryer (gas) has electronic spark ignition ASSEMBLY that lights a standing pilot. The gap between the spark electrode and the pilot hood should be set at 1/8 of an inch. 1. Remove electrical power supplied to the unit. To avoid electrical shock or property damage, move the POWER ...

  • Henny Penny OFE/OFG-324 - page 10

    Model OFE/OFG-321,322,323,324 2-9. IGNITOR MODULE During normal operation, the ignition modules send 24 volts to the ignitors and gas control valve. If a module does not sense a pilot flame, the module starts the ignition process again. But, if a pilot light goes out for longer that 10 seconds, or it goes out 3 times within 10 seconds, the module k ...

  • Henny Penny OFE/OFG-324 - page 11

    Model OFE/OFG-321,322,323,324 2-11. I/O POWER SUPPLY BOARD ASSEMBLY The input/output power supply board assembly distributes voltage to the various components in the fryer. The board also receives information from com ponents in the fryer. 1. Remove electrical power supplied to the unit. To avoid electrical shock or property damage, move the POWER ...

  • Henny Penny OFE/OFG-324 - page 12

    Model OFE/OFG-321,322,323,324 2-12. VACUUM SWITCH (Continued) 5. Using a Phillips head screwdriver, remove the screws securing the vacuum switch to the shroud. 6. Install the new vacuum switch in reverse order. To avoid property damage, do not tamper with, or disas- semble this component. It is set and sealed from the factory and is not to be adjus ...

  • Henny Penny OFE/OFG-324 - page 13

    Model OFE/OFG-321,322,323,324 2-14. DRAIN MICROSWITCH Upon turning the drain handle, the drain microswitch circuit should open, cutting off the pilot flame. This will prevent the fryer from heating while shortening is being drained from the frypot. 1. Remove electrical power supplied to the unit. To avoid electrical shock or property damage, move t ...

  • Henny Penny OFE/OFG-324 - page 14

    Model OFE/OFG-321,322,323,324 2-15. FILTER SWITCH (Continued) 2. Remove the control panel above the switch. 3. Label and remove the wires from the switch. W ith test instrument, check across the terminals of the switch with the switch in the ON position, and then in the OFF position. With the switch in the ON position, the circuit should be closed. ...

  • Henny Penny OFE/OFG-324 - page 15

    Model OFE/OFG-321,322,323,324 2-16. GAS CONTROL VALVE ASSEMBLY (Continued) 3. Using a 7/16 inch wrench, remove the pilot line from the gas control valve. 4. Using a 1 inch wrench, loosen the nut securing the main gas inlet line to the gas control valve. 5. Using 5/8 inch wrench, remove the two burner gas line fittings at the black tee fitting, loca ...

  • Henny Penny OFE/OFG-324 - page 16

    Model OFE/OFG-321,322,323,324 2-16. GAS CONTROL VALVE ASSEMBLY (Continued) 7. With the bracket dropped down, remove the two screws behind the bracket securing the gas control valve to the bracket. 8. Install the new gas control valve in reverse order. 2-17. BLOWER MOTOR ASSEMBLY The blower motor assembly induces the draft for the burners. If the bl ...

  • Henny Penny OFE/OFG-324 - page 17

    Model OFE/OFG-321,322,323,324 2-17. BLOWER MOTOR ASSEMBLY (Continued) 4. Remove wire nuts connecting blower motor wires to wires in conduit. 5. Loosen conduit from blower motor. 6. Remove screws connecting flue to bracket in upper frame. 7. Remove screws connecting flue to blower. 203 2-17 ...

  • Henny Penny OFE/OFG-324 - page 18

    Model OFE/OFG-321,322,323,324 2-17. BLOWER MOTOR ASSEMBLY (Continued) 8. Using 3/8 inch nut driver, remove nuts securing blower to the unit. Pull blower from unit. 9. Install new blower in reverse order. 2-18. HEATING ELEMENTS (ELECTRIC ONLY) Heating elements are available for 208 and 230 volts. Check data plate to determine correct voltage. C h e ...

  • Henny Penny OFE/OFG-324 - page 19

    Model OFE/OFG-321,322,323,324 2-18. HEATING ELEMENTS (ELECTRIC ONLY) (Continued) 3. Perform an ohm check on one element at a tim e, with wires disconnected from element. If the resistance is not within tolerance, replace the element. Voltage Wattage Resistance Ohms (cold) 208 4800 9 230 4800 11 Replacement: Refer to figure 2-2. 1. Drain the shorten ...

  • Henny Penny OFE/OFG-324 - page 20

    Model OFE/OFG-321,322,323,324 2-18. HEATING ELEMENTS (ELECTRIC ONLY) (Continued) 9. Evenly space the element spreaders on the sides of the elements and reinstall bolts. Place the fifth spreader in the front of the elements as to protect the temperature probe. (Fig.6-1 10. Replace the high limit bulb holder on the top element, and position the bulb ...

  • Henny Penny OFE/OFG-324 - page 21

    Model OFE/OFG-321,322,323,324 2-19. HEATING CONTACTORS (ELECTRIC ONLY) Each well of an electric fryer requires two switching contactors. The first in line is the primary contactor and the second in line is the heat contactor. When open, the primary contactor does not allow power to flow to the heat contactor. When closed, the primary supplies volta ...

  • Henny Penny OFE/OFG-324 - page 22

    Model OFE/OFG-321,322,323,324 2-19. HEATING Checkout (Power Supplied) CONTACTORS (ELECTRIC ONLY) (Continued) To avoid electrical shock, make connections before applying power, take reading, and remove power before removing meter leads. The following checks are performed with the wall circuit breaker closed and the main power switch in the ON positi ...

  • Henny Penny OFE/OFG-324 - page 23

    Model OFE/OFG-321,322,323,324 2-20. SPEAKER ASSEMBLY (Electric Units) The speaker assembly emits audible signals to let the operator know when cooking and hold times are finished. 1. Remove electrical power supplied to unit. To avoid electrical shock or property damage, move the POWER switch to OFF and disconnect main circuit breaker, or unplug cor ...

  • Henny Penny OFE/OFG-324 - page 24

    Model OFE/OFG-321,322,323,324 2-21. HIGH TEMPERATURE 1. Drain the shortening from the frypot. LIMIT CONTROL (Electric Units) (Continued) 2. Remove control panel. 3. Loosen small inside screw nut on capillary tube. 4. Remove capillary bulb from bulb holder inside the frypot. 5. Straighten the capillary tube. 6. Remove larger outside nut that threads ...

  • Henny Penny OFE/OFG-324 - page 25

    Model OFE/OFG-321,322,323,324 2-21. HIGH TEMPERATURE LIMIT CONTROL (Electric Units) (Continued) Be sure capillary bulb of high limit is located behind capillary bulb of thermostat. Both capillary bulbs and bulb holders should be positioned as not to interfere with basket or when cleaning the frypot wall, or damage to capillary tube could result. 13 ...

  • Henny Penny OFE/OFG-324 - page 26

    Model OFE/OFG-321,322,323,324 2-22. AUTOLIFT ACTUATOR (MOTOR) REPLACEMENT (if applicable) (Continued) 5. Disconnect actuator connector and cut the wires from the other half of the connector, as shown at left. The new actuator wires do not have a connector on them and must be connected directly to the wires on the unit. 6. Using a 3/8 socket, remove ...

  • Henny Penny OFE/OFG-324 - page 27

    Model OFE/OFG-321,322,323,324 2-22. AUTOLIFT ACTUATOR (MOTOR) REPLACEMENT (if applicable) (Continued) 9. Remove the 2 front mounting screws from the actuator support plate. 10. Remove all the top screws, securing all the actuator support plates to the back shroud, to help loosen the back shroud. 11. Remove all remaining back shroud screws to loosen ...

  • Henny Penny OFE/OFG-324 - page 28

    Model OFE/OFG-321,322,323,324 2-23. AUTOLIFT 1. Remove electrical power supplied to unit. TRANSFORMER REPLACEMENT (if applicable) To avoid electrical shock or property damage, move the power switch to OFF and disconnect main circuit breaker, or unplug cord at wall receptacle. 2. Remove control panel. 3. Label and remove wires from transform er. 4. ...

  • Henny Penny OFE/OFG-324 - page 29

    Model OFE/OFG-321,322,323,324 2-24. AUTOLIFT PC BOARD REPLACEMENT (if applicable) (Continued) 4. Using a Phillips-head screwdriver, remove the 2 screws securing the autolift PC board bracket to the frame and remove bracket from unit. (The right screw needs removed to disconnect the ground wire, but the left screw can be loosened and the bracket sli ...

Manufacturer Henny Penny Category Fryer

Documents that we receive from a manufacturer of a Henny Penny OFE/OFG-324 can be divided into several groups. They are, among others:
- Henny Penny technical drawings
- OFE/OFG-324 manuals
- Henny Penny product data sheets
- information booklets
- or energy labels Henny Penny OFE/OFG-324
All of them are important, but the most important information from the point of view of use of the device are in the user manual Henny Penny OFE/OFG-324.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Henny Penny OFE/OFG-324, service manual, brief instructions and user manuals Henny Penny OFE/OFG-324. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Henny Penny OFE/OFG-324.

Similar manuals

A complete manual for the device Henny Penny OFE/OFG-324, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Henny Penny OFE/OFG-324 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Henny Penny OFE/OFG-324.

A complete Henny Penny manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Henny Penny OFE/OFG-324 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Henny Penny OFE/OFG-324, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Henny Penny OFE/OFG-324, that we can find in the current document
3. Tips how to use the basic functions of the device Henny Penny OFE/OFG-324 - which should help us in our first steps of using Henny Penny OFE/OFG-324
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Henny Penny OFE/OFG-324
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Henny Penny OFE/OFG-324 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Henny Penny OFE/OFG-324?

Use the form below

If you did not solve your problem by using a manual Henny Penny OFE/OFG-324, ask a question using the form below. If a user had a similar problem with Henny Penny OFE/OFG-324 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)