-
Sears 200.713101 - page 1
OWNER'S MANUAL DieHard 10/2/60 AMP FULLY AUTOMATIC BATTERY CHARGER ENGINE STARTER Model No. 200.713101 CAUTION: Before first use of charger, read this manual, and follow all its Safety and Operating Instructions with every charger use. Save these instructions. Made in U.S.A. of U.S. and imported parts. Sears, Roebuck and Co., Hoffman Estates, ...
-
Sears 200.713101 - page 2
WARRANTY ............................................................................................................... 2 SAFETY ..................................................................................................................... 3 Important Safety Instructions ...................................................................... ...
-
Sears 200.713101 - page 3
WARNING: To reduce the risk of explosion, explosive gases, or injury while using your battery charger, follow the precautions listed below: • Read all instructions and cautions printed on the battery charger, battery, and vehicle or equipment using battery. • Use charger only on lead-acid type rechargeable batteries, such as those used in cars, ...
-
Sears 200.713101 - page 4
Personal Safety Precautions For your own personal safety, please follow the following precautions: • Wear complete eye and clothing • Remove all personal metal items protection when working with lead- acid batteries. • Be sure that someone is within range of your voice to come to your aid if needed while you work with or are near a lead-acid ...
-
Sears 200.713101 - page 5
It is important to understand your charger's requirements. This section will tell you about your charger's electrical requirements and how to prepare a battery for charging. ASSEMBLINGYOURCHARGER Included with your battery charger are two cord wrap posts for storage of the clamp cables. To install, align the three tabs to corre- spond wit ...
-
Sears 200.713101 - page 6
It is important that you read and follow these guidelines while you are preparing to charge your battery. • Make sure that you have a 12 volt or 6 volt lead-acid battery. Set the selector switch to match the voltage rating of the battery to be charged. • Clean the battery terminals. Be careful to keep corrosion from getting in or around your ey ...
-
Sears 200.713101 - page 7
Charge Type: • Use the MANUAL setting only if you check the charging progress frequently. The charger will not stop charging when the battery reaches full charge, possibly damaging the battery it left on too long. You must monitor and unplug the charger when battery is fully charged. • Use the AUTOMATIC DEEP CYCLE setting for all deep cycle bat ...
-
Sears 200.713101 - page 8
• When using AUTOMATIC charge rates, the LED will cycle on and off indicating the charger is maintainingthe battery's state-of-charge. CHARGING YOUR BAI-I'ERY Charging your battery inside the vehicle: . . . , . Arrange the power cord and charg- ing leads carefully to avoid damage that could be caused by the hood, door, or moving engine ...
-
Sears 200.713101 - page 9
Charging your battery outside the vehicle: . Remove the battery from vehicle, making sure to disconnect grounded terminal first with all accessories and lights turned off in the vehicle. . Check the polarity of the battery posts as indicated on the battery case: POSITIVE (POS, P, +) and NEGATIVE (NEG, N, -). NOTE: On top-post batteries, the positiv ...
-
Sears 200.713101 - page 10
Your battery charger can be used to jump start your car if the battery is low. Follow these instructions on how to use the ENGINE START feature. 1. Connect the charger to the battery and vehicle as instructed in the "Charging your battery"section on page 8. 2. Setthe right hand SELECTOR SWITCH on ENGINE START. , Crank the engine for no mo ...
-
Sears 200.713101 - page 11
Battery Rating Method Use the following table to more accurately determine the time it will take to fully charge a battery that is initially at 50% State-of-Charge. Identify you r battery type and its associated Charge Time in the table. Common battery types are: • Small batteries, motorcycles, garden tractors, etc., are usually rated in Amp-Hour ...
-
Sears 200.713101 - page 12
Charge Time Needed if Amp-Hours is Known • Find the Charge Factor for your battery in the table on page 11. • Multiply by the Amp-Hour rating of the battery. • Divide by the Charger Setting (either 2 Amp or 10 Amp.) • Multiply by 1.25 to get the approximate Hours Neededto bring the battery to full charge. Example: 15 Amp-Hour (AH) Battery, ...
-
Sears 200.713101 - page 13
Performance problems often result from little things ahat you can't fix yourself. Please read through this chart for a possible solution if a I PROBLEM POSSIBLE CAUSE No ammeter reading. Clamps not making good connection. Circuit breaker in charger cycles on and off with a clicking sound in the MANUAL setting. Ammeter reads less than selected ...
-
Sears 200.713101 - page 14
This section shows an illustration of your battery charger. Use it to become familiar with where all the parts are located, and what they look like. Item Description Part Number 1 Transformer 93026484 2 Diode Asm Kit 2299000976 3 PC Board Asm 2299000966 4 Circuit Breaker 3999000088 5 DC Cable Asm 3899000850 6 SCR55A 3100300017 7 Power Cord 90026105 ...
-
Sears 200.713101 - page 15
BRN 15 ...
-
Sears 200.713101 - page 16
For information about troubleshooting Call toll-free from anywhere in the U.S.A. 7 am to 4:30 pm CST Monday through Friday 1-800-732-7764 (1-800-732-7764) For the repair or replacement parts you need Call 7 am - 7 pro, 7 days a week 1-800-366-PART (1-800-366-7278) For the location of an authorized Sears Service Center in your area Call 24 hours a d ...
Do you have a question concerning Sears 200.713101?
Use the form below
If you did not solve your problem by using a manual Sears 200.713101, ask a question using the form below. If a user had a similar problem with Sears 200.713101 it is likely that he will want to share the way to solve it.