English dropdown-ico

Manual Echo CS-620P

34 pages 1.99 mb
Download

Go to site of 34

Summary
  • Echo CS-620P - page 1

    INSTRUCTION MANUAL CHAIN SAW CS-620P WARNING Read the instructions carefully and follow the rules for safe operation. Failure to do so could result in serious injury. X750-022 43 0 X750 326-250 0 ECHO, INCORPORATED 400 Oakwood Road, Lake Zurich, Illinois 60047-1564 Phone : 847-540-8400 Printed in Japan 1311Fn 0890 ES ...

  • Echo CS-620P - page 2

    Copyright © 2013 All Rights Reserved. The engine exhaust fr om this product contains c hemicals known to the State of California to cause cancer , birth defects or other reproductive harm. W ARNING ...

  • Echo CS-620P - page 3

    1 CS-620P RULES FOR SAFE OPERATION A. Kickback Safety Precautions for Chain Saw Users 1. With a basic understanding of kickback, you can reduce or eliminate the element of surprise. Sudden surprise contributes to accidents. 2. Keep a good firm grip on the saw with both hands, the right hand on the rear handle, and the left hand on the front handle ...

  • Echo CS-620P - page 4

    2 CS-620P 1. Do not operate a chain saw with one hand! Serious injury to the operator, helpers, bystanders, or any combination of these persons may result from one- handed operation. A chain saw is intended for two-handed use. 2. Do not operate a chain saw when you are fatigued. 3. Use safety footwear, snug-fitting clothing and protective gloves. ...

  • Echo CS-620P - page 5

    3 CS-620P WARNING The safety alert symbol accompanied by the word “WARNING” calls attention to an act or condition which CAN lead to serious personal injury or death if not avoided. CAUTION The safety alert symbol accompanied by the word “CAUTION” calls attention to an act or condition which may lead to minor or moderate personal injury if ...

  • Echo CS-620P - page 6

    4 CS-620P SYMBOL FORM DECALS Locate this safety decal on your unit. The complete unit illustration found in the “NOMENCLATURE OF PARTS” section will help you locate them. Make sure the decal is legible and that you understand and follow the instructions on it. If a decal cannot be read, a new one can be ordered from your ECHO dealer. P ar t Num ...

  • Echo CS-620P - page 7

    5 CS-620P PACKING LIST The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, guide bar and saw chain installation and other assembly may be necessary. After opening the carton, check for damage. Immediately notify your retailer or ECHO dealer of damaged or missing parts. Use the packing l ...

  • Echo CS-620P - page 8

    6 CS-620P NOMENCLATURE OF PARTS * If a decal cannot be read, a new one can be ordered from your ECHO dealer. 19 14 15 17 16 5 4 8 7 10 11 12 3 2 1 X524-004670 890191-30131 9 21 6 22 20 23 18 13 P ar t Number 890191-30131 Part Number X524-004670 REPLACEMENT BAR AND CHAIN GUIDE BAR* CHAIN* PART NO. PART NO. 16” 16D0PS3860 72LPX60CQ 18” 18D0PS3866 ...

  • Echo CS-620P - page 9

    7 CS-620P 1. Instruction manual - Included with unit. Read before operation and keep for future reference to learn proper, safe operating techniques. 2. Safety manual - Describe operating and safety instructions for this chain saw. 3. Spiked bumpers - Device, fitted in front of the guide bar mounting point, acting as a pivot when in contact with a ...

  • Echo CS-620P - page 10

    8 CS-620P OPERATOR SAFETY VIBRATION AND COLD s )TISBELIEVEDTHATACONDITIONCALLED2AYNAUDS Phenomenon, which affects the fingers of certain individuals, may be brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning followed by loss of color and numbness in the fing ...

  • Echo CS-620P - page 11

    9 CS-620P SPARK ARRESTOR MUFFLER s 4HESPARKARRESTORMUFmERCONTROLSTHEEXHAUST noise and prevents hot, glowing particles of carbon from leaving the muffler. Make sure the spark arrestor screen is in good repair and properly seated in the muffler. s #ERTAININTERNALCOMBUSTIONENGINESOPERATEDON forest, brush, ...

  • Echo CS-620P - page 12

    10 CS-620P WARNING Saw chain is sharp! Always wear gloves when handling assembly, otherwise serious personal injury may result. KICK GUARD ® TO BAR INSTRUCTIONS Tools Needed: Two 11 mm (7/16 in.) Wrenches. For saws with Kick Guard ® P/N 2893201 and Symmetrical Low-Kick type (Double Guard) guide bars. 1. Install bolt (A) in front hole (B) of Kick ...

  • Echo CS-620P - page 13

    11 CS-620P ADJUSTING CHAIN TENSION IMPORTANT Always loosen clutch cover nuts before turning the chain tension adjuster, otherwise the clutch cover and tensioner will be damaged. 1. Remove spark plug lead. (See page 25) 2. Unlock the chain brake and loosen two clutch cover nuts, if necessary. 3. Hold the bar nose up, and turn the adjuster screw cloc ...

  • Echo CS-620P - page 14

    12 CS-620P Fuel Mix Chart 50 : 1 U.S. Metric Gasoline Oil Gasoline Oil Gallons US. fl. oz. L mL 1 2.6 4 80 2 5.2 8 160 5 12.8 20 400 FUEL AND LUBRICANT FUEL STATEMENT GASOLINE - Use 89 Octane [(R+M)/2] (mid grade or higher) gasoline or gasohol known to be good quality. Gasohol may contain up to 10 % Ethyl (grain) alcohol or 15 % MTBE (methyl teria ...

  • Echo CS-620P - page 15

    13 CS-620P HANDLING FUEL MIXING INSTRUCTIONS - 1. Fill an approved fuel container with half of the required amount of gasoline. 2. Add the proper amount of two-stroke oil to gasoline. 3. Close container and shake to mix oil with gasoline. 4. Add remaining gasoline, close fuel container, and remix. IMPORTANT s 3PILLEDFUELISALEADING ...

  • Echo CS-620P - page 16

    14 CS-620P WARNING s !FTERCHOKECONTROLKNOBISPULLEDANDTHEN knob is returned to original position, throttle remains a little open (latch condition). s )FENGINEISSTARTEDINTHISLATCHCONDITION chain starts to turn. Do not start engine before chain brake is activated. CAUTION s !FTERSTARTING? ...

  • Echo CS-620P - page 17

    15 CS-620P WHEN THE ENGINE IS COLD CAUTION Make sure the bar and chain are free from any obstruction when starting the chain saw. s -OVECHAINBRAKELEVERFULLYFORWARDTOLOCK chain brake before starting. s &ILLTHEFUELTANKWITHFUELMIXTURE It is not permitted to fill fuel above the shoulder level o ...

  • Echo CS-620P - page 18

    16 CS-620P RUNNING s 7HENENGINESTARTSKEEPIDLINGFORAFEW minutes. s 3ETTHEBRAKELEVERINTHEUNLOCKEDPOSITION before starting to cut. s 0ULLTHROTTLETRIGGERGRADUALLYANDINCREASE revolution of the engine. s 4HECHAINSTARTSRUNNINGWHENTHEENGINE reaches 4000 r/ ...

  • Echo CS-620P - page 19

    17 CS-620P CUTTING INSTRUCTION GENERAL CAUTION s 2EADTHE%#(/h#(!).3!73!&%49 MANUAL” included with your chain saw for additional cutting and safety instructions. s 7EARSUITABLEHEARINGPROTECTIONSUCHAS earmuffs or earplugs to protect against objectionable or uncomfortable loud noises. s $ONOTLET ...

  • Echo CS-620P - page 20

    18 CS-620P FELLING THE TREE A falling tree can seriously damage anything it may hit - a car, a house, a fence, a power-line, or another tree. There are ways to make a tree fall where you want it, so first decide where that is! Before cutting, clear the area around the tree. You will need good footing while working and you should be able to work th ...

  • Echo CS-620P - page 21

    19 CS-620P LIMBING Limbing a fallen tree is much the same as bucking. Never stand on the tree that you are limbing. When limbing, caution is the word. Be careful of the tip touching other limbs. Always use both hands. Don’t cut with the saw overhead or aligned vertically with your body. If the saw should kick- back, you may not have enough contro ...

  • Echo CS-620P - page 22

    20 CS-620P Chain brake function When the lever is pushed forward, chain brake instantly stops the chain. Chain brake unlock When the lever is fully pulled toward the operator, brake is unlocked. When the bar nose hits another tree, etc. Improper thrust cutting CHAIN BRAKE OPERATION s 3ETTHELEVERINTHEUNLOCKEDPOSITIONBEFORE ...

  • Echo CS-620P - page 23

    21 CS-620P End of the guide bar may be placed at the height of about 40 cm (16 in.). 40 cm (16 in.) AUTOMATIC CHAIN BRAKE Kickback produced from the tip of the guide bar will trip the automatic chain brake. To make sure that the automatic chain brake operates properly, follow these steps: 1. Stop the engine. 2. Hold the saw with the guide bar appro ...

  • Echo CS-620P - page 24

    22 CS-620P CHAIN AND GUIDE BAR COMBINATION The following combinations are recommended for model CS-620P . GUIDE BAR (Low-kickback) Replacement guide bars. The following guide bars may be considered to have equivalent kickback energy. s 3PROCKETNOSEGUIDEBARSOFTHESAMELENGTH and nose radius, same pitch and having the same nu ...

  • Echo CS-620P - page 25

    23 CS-620P MAINTENANCE AND CARE IMPORTANT Time intervals shown are maximum. Actual use and your experience will determine the frequency of required maintenance. Your ECHO chain saw is designed to provide many hours of trouble free service. Regular scheduled maintenance will help your chain saw achieve that goal. If you are unsure or are not equippe ...

  • Echo CS-620P - page 26

    24 CS-620P CARBURETOR ADJUSTMENT Every unit is run at the factory and the carburetor is set in compliance with Emission Regulations. In addition, the carburetor is equipped with “H” (High Speed) and “L” (Low Speed) needle adjustment limiters that prevent settings outside acceptable limits. 1. Before adjusting carburetor clean or replace air ...

  • Echo CS-620P - page 27

    25 CS-620P Oil filter Fuel filter Oil tank cap Fuel tank cap 0.65 mm (0.026 in.) Cleaner cover knob Air filter Air cleaner cover AIR FILTER s #HECKBEFOREEVERYUSE s #LOSECHOKE ). s 4URNCLEANERCOVERKNOBCOUNTERCLOCKWISEBY hand and remove air cleaner cover and air filter. s "RUSHOFFDU ...

  • Echo CS-620P - page 28

    26 CS-620P GUIDE BAR s #LEANBEFOREUSING - Clean the groove of the guide bar with a small screwdriver. - Clean oil holes with a wire. s 2EVERSEGUIDEBARPERIODICALLY s #HECKSPROCKETANDTHECLUTCHANDCLEANTHEBAR mount area before installation of the bar. Replace either or both if worn. SPROCKE ...

  • Echo CS-620P - page 29

    27 CS-620P SETTING THE SAW CHAIN Shar pen lo wer edge Drive link Tie strap Right hand cutter Preset tie strap Left hand cutter Guard link Top plate Side plate Depth gauge Hold the file tipped 10° upward 10° Important points for proper maintenance of saw chain: s +EEPTHECUTTERSSHARPATALLTIMES s +EEPTHELEFTAN ...

  • Echo CS-620P - page 30

    28 CS-620P s 0LACETHEDEPTHGAUGETOOLlRMLYONGUIDEBAR so that depth gauge protrudes. Then file top of depth gauge with the flat file until flat with top of the depth gauge tool. - Be sure to round off the front edge of the depth gauge. Properly filed cutters are shown in illustration. When setting of the chain is fi ...

  • Echo CS-620P - page 31

    29 CS-620P TROUBLESHOOTING WARNING Fuel vapors are extremely flammable and MAYCAUSElREANDOREXPLOSION.EVERTEST for ignition spark by grounding spark plug near cylinder plug hole, otherwise serious personal injury may result. Problem Engine — hard to start Cause Remedy — does not start Engine cranks Fuel at carburetor ...

  • Echo CS-620P - page 32

    30 CS-620P STORAGE AFTER USE * Technical data subject to change without notice. TECHNICAL DATA s )NSPECTANDADJUSTEVERYPARTOFTHECHAINSAW - Completely clean every part and repair if necessary. - Apply thin coating of oil on metal parts to prevent rust. s 2EMOVECHAINANDGUIDEBAR s $RAINFUEL ...

  • Echo CS-620P - page 33

    31 CS-620P WARRANTY STATEMENTS ECHO LIMITED WARRANTY STATEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010 ECHO’S RESPONSIBILITY ECHO Incorporated’s Limited Warranty, provides to the original purchaser that this ECHO product is free from defects in material and workmanship. Under normal use and maintenance from date of purchase, ECH ...

  • Echo CS-620P - page 34

    32 CS-620P PURCHASED REPAIR PARTS, SHORT BLOCKS AND ACCESSORIES s DAYRESIDENTIALORNONINCOMEPRODUCINGWARRANTY s DAYCOMMERCIALINSTITUTIONALAGRICULTURALINDUSTRIALINCOMEPRODUCINGORRENTALAPPLICATIONWARRANTY ATTENTION TWO-STROKE ENGINE POWER PRODUCT OWNERS This ECHO ...

Manufacturer Echo Category Chainsaw

Documents that we receive from a manufacturer of a Echo CS-620P can be divided into several groups. They are, among others:
- Echo technical drawings
- CS-620P manuals
- Echo product data sheets
- information booklets
- or energy labels Echo CS-620P
All of them are important, but the most important information from the point of view of use of the device are in the user manual Echo CS-620P.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Echo CS-620P, service manual, brief instructions and user manuals Echo CS-620P. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Echo CS-620P.

Similar manuals

A complete manual for the device Echo CS-620P, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Echo CS-620P by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Echo CS-620P.

A complete Echo manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Echo CS-620P - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Echo CS-620P, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Echo CS-620P, that we can find in the current document
3. Tips how to use the basic functions of the device Echo CS-620P - which should help us in our first steps of using Echo CS-620P
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Echo CS-620P
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Echo CS-620P in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Echo CS-620P?

Use the form below

If you did not solve your problem by using a manual Echo CS-620P, ask a question using the form below. If a user had a similar problem with Echo CS-620P it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)