English dropdown-ico

Manual GarrettCom Magnum 6K32T

67 pages 1.01 mb
Download

Go to site of 67

Summary
  • GarrettCom Magnum 6K32T - page 1

    i www Garre t t C om c om .. www Garre t t C om c om .. Corporate Headquarters GarrettCom, Inc. 47823 Westinghouse Dr. Fremont, CA 94539-7437 Phone (510) 438-9071 Fax (510) 438-9072 Website: http://www.GarrettCom.com email support@garrettcom.c om Magnum 6K32T Managed Switch Installation and User Guide Hardware User Manual ...

  • GarrettCom Magnum 6K32T - page 2

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) i www Garre t t C om c om .. Magnum  6K32T Managed Switch Hardw are Installation and User Guide Part #: 84-00138 (Rev. B) Trademarks Ethernet is a trademark of Xerox Corporation NEBS is a trademark of Telcordia Technologies UL is a registered trademark of Underwriters Lab ...

  • GarrettCom Magnum 6K32T - page 3

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) ii www Garre t t C om c om .. Contacting GarrettCom, Inc Please use the mailing address, phone and fax numbers and email address listed below: GarrettCom, Inc. 47823Westinghouse Dr. Fremont, CA 94539-7437 Phone (510) 438-9071 Fax (510) 438-9072 Website: http://www.GarrettCom ...

  • GarrettCom Magnum 6K32T - page 4

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) iii www Garre t t C om c om .. TABLE OF CONTEN TS .......................................................................... Page 1.0 SPECIFICATIONS ................................................................................ 1 1.1 Technical Speci fications.............. ...

  • GarrettCom Magnum 6K32T - page 5

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) iv www Garre t t C om c om .. 4.5 Flow-control, IEEE 802.3x standard .................................................. 41 4.6 Power Budget Calcul ations for Magnum 6K32T PM’s Error! Bookmark n 5.0 MAGNUM 6K32T MANAGED SWITCH PORT MODULES ....... 41 5.1 Inspecting the Pack ...

  • GarrettCom Magnum 6K32T - page 6

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) www Garre t t C om c om .. The Magnum Line ETHERNET CONNECTIVITY PRODUCTS "DESIGNED AND M ANUFACTURED IN THE US A" OVERVIEW GarrettCom, Inc. offers the premium-quality Magnum  line of Ethernet LAN connectivity products with industry -sta ndard functionality and ...

  • GarrettCom Magnum 6K32T - page 7

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 1 www Garre t t C om c om .. 1.0 SPECIFICATIONS 1.1 Technical Specifications Performance Filtering / Forwarding Rate: Ethernet:14,880 pps Fast Ethernet: 148,800 pps Gigabit Ethernet: 1,488,000 pps Switching Processing Ty pe: Store and Forward with IEEE 802.3x full- duplex fl ...

  • GarrettCom Magnum 6K32T - page 8

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 2 www Garre t t C om c om .. Fiber connec tor types supported: ST-type (twist-lock) SC-type (snap-in) MTRJ-ty pe Small Form Factor (SFF) LC-type Sm all Form Factor (SFF) GBIC modules LEDs: Per Port LK: Steady ON when media link is operational ACT: ON with receiver port activ ...

  • GarrettCom Magnum 6K32T - page 9

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 3 www Garre t t C om c om .. For ( Optional ) DC inte rnal power supplies at –48VDC, 24VDC and 125VDC, including Dual Source options ( for continuity of operation when either of the DC input sources are interrupted) , see Appendices B and C. Relay Alarm Contact (Optional) ...

  • GarrettCom Magnum 6K32T - page 10

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 4 www Garre t t C om c om .. 1.2 Ordering Information Magnum Managed Switch MODEL DESCRIPTION Magnum 6K32T 24 10/100 RJ-45 ports and either tw o optional port modules (6K32T) or one optional port module slot (6K32), which may be configured with a selection of 10/100/1000Mb f ...

  • GarrettCom Magnum 6K32T - page 11

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 5 www Garre t t C om c om .. GBIC-SXSC GBIC transceiver module for use in GBPM-xOTX. One 1000BASE-SX port with multimode SC fiber connector 6KP5-G4RJ “G+4” module, with one GBIC ope n transceiver and four 10/100 RJ-45 connectors (includes front–panel metal sheet) 6KP5- ...

  • GarrettCom Magnum 6K32T - page 12

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 6 www Garre t t C om c om .. 2.0 Introduction 2.1 Inspecting the Package and Product Examine the shipping container for obvious damage prior to installing this product; notify the carrier of any damage that you believe occurred during shipment or delivery. Inspect the conten ...

  • GarrettCom Magnum 6K32T - page 13

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 7 www Garre t t C om c om .. 2.2 Product Description - Magnum 6K32T Managed Switch The Magnum 6K32T Managed Switch provides high port density, with up to 32 ports in a 1U rack-mount package. It is used to boost the performance of large Ethernet LANs, typically serving as a ? ...

  • GarrettCom Magnum 6K32T - page 14

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 8 www Garre t t C om c om .. accommodated include standard 19” RETMA, ETS I, and 23” Telco. Input power m ay be AC, or –48VDC for Telco environments, or 24VDC for Industrial applications. Designed for use in network traffic centers, the Magnum 6K32T provides high perfo ...

  • GarrettCom Magnum 6K32T - page 15

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 9 www Garre t t C om c om .. Magnum 6K32T is easy to deploy, manage a nd maintain. Addresses of attached nodes are automatically learned and maintained, adapting the switching services to network changes and expansions to pr ovide pug-n-play operation. 2.2.1b New Magnum 6K32 ...

  • GarrettCom Magnum 6K32T - page 16

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 10 www Garre t t C om c om .. 2.2.2 Eight-port SFF fiber modules (6K8-MTRJ, 6K8-MLC), 100Mb fi ber Fig.2.2.2 : SFF Fiber Port Modules, 6K8-MTRJ (to the left) and 6K8-MLC or -SLC (below) In an eight-port SFF fiber port module, all of the fiber ports are of the same speed (100 ...

  • GarrettCom Magnum 6K32T - page 17

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 11 www Garre t t C om c om .. 2.3 Eight-Port Copper Module, 6K8-RJ45 The 6K-Series’s 8-port Copper port module, model 6K8-RJ45, provides eight 10/100Mb switched RJ-45 ports. The 10/100Mb switched ports normally (as a default setting) are independently N-way au to-negotiati ...

  • GarrettCom Magnum 6K32T - page 18

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 12 www Garre t t C om c om .. 2.2.4 Six-Port “4 + 2”Combo Modules, 4@ 10/100 RJ-45 and 2@100Mb fiber 4@RJ-45 + 2@ 100Mb ST or SC The combo six-port modules are combinations of copper and fiber media, available as four 10/100 switched RJ-45 copper ports a nd two 100Mb swi ...

  • GarrettCom Magnum 6K32T - page 19

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 13 www Garre t t C om c om .. The 4port @10Mb ST fiber modules be have the same as the 8@100Mb ST fiber modules except for the 10Mb speed. For port numbering, ports 1, 2, 5, 6 are present, ports 3, 4. 7, 8 are not present. The de fault setup on the 10Mb fiber module is half- ...

  • GarrettCom Magnum 6K32T - page 20

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 14 www Garre t t C om c om .. port is by default configured to AUTO m ode, and can be fixed at 1000Mbps speed full- duplex mode at any time. The Gigabit fiber port has LEDs that indicate LK (Link status) and ACT (receiving activity) on that port when lit. 2.2.7 Packet Priori ...

  • GarrettCom Magnum 6K32T - page 21

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 15 www Garre t t C om c om .. devices sending packets to cause “flow cont rol”. This tells the sending devices to temporarily stop sending traffic, which allo ws a traffic catch-up to occur without dropping packets. Then, normal packet buffering and processing resumes. A ...

  • GarrettCom Magnum 6K32T - page 22

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 16 www Garre t t C om c om .. 2.3 Features and Benefits  Managed switching for high performance Eth ernet LANs Magnum 6K32T Switches provide non-blocking (all ports can run at full speed at once) performance with standard Managed Networks Software (MNS-6K) included. They ...

  • GarrettCom Magnum 6K32T - page 23

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 17 www Garre t t C om c om .. 2.4 Applications Magnum 6K32T Fiber Switches offer hi gh performance along with one or two modular slot options to fulfill the choice of copper/Fiber, 10,100 or 1000Mb requirements. The 6K32T also offers MN S-6K management so ftware. Magnum 6K32 ...

  • GarrettCom Magnum 6K32T - page 24

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 18 www Garre t t C om c om .. fire hazards can be connected to one or two full duplex Gigabit Fiber ports. Full-duplex future proof fiber media can easily connect long distance subnets and provide a stable secure network to all applications. The SNMP management capability of ...

  • GarrettCom Magnum 6K32T - page 25

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 19 www Garre t t C om c om .. support of 10/100 and 1000Mb. The user can utilize the SNMP feature equipped with VLAN, Port security, 802.1X, and other security features to provide a secure and stable network as per the requirement The 6K32T Managed Switch with NEBS Level 3 c ...

  • GarrettCom Magnum 6K32T - page 26

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 20 www Garre t t C om c om .. Example 4: In a “ (video+data)” application where a network being designed to catered the need of multicast and broadcast traffi c of higher bandwidth to provide a video conferencing and video in demand channel option to the user. The Magnum ...

  • GarrettCom Magnum 6K32T - page 27

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 21 www Garre t t C om c om .. Figure 4: A multicast traffic through a 6K32T Swi tches with Gigabit redundancy ...

  • GarrettCom Magnum 6K32T - page 28

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 22 www Garre t t C om c om .. 3.0 Installation Before installing the equipment, it is necessary to take the following precautions: 1.) If the equipment is mounted in an enclosed or multiple rack assembly, the environmental temperature around the equipment must be less than o ...

  • GarrettCom Magnum 6K32T - page 29

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 23 www Garre t t C om c om .. 3.2 Connecting Ethernet Media The Magnum 6K32T Switches are specifically designed to support all standard Ethernet media types within a single Switch unit. This is accomplished by using a family of different port Modules which can be individuall ...

  • GarrettCom Magnum 6K32T - page 30

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 24 www Garre t t C om c om .. 3.2.2 Connecting Fiber Optic SC-type , "Snap-In" The following procedure applies to insta llations using a PM with SC-type fiber connectors, i.e., using 6K-MSC or 6K-SSC (single mode) etc. When connecting fiber media to SC connectors, ...

  • GarrettCom Magnum 6K32T - page 31

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 25 www Garre t t C om c om .. 3.2.5 Connecting Twisted P air (CAT-5e or be tte r , Unshielded or Shielded) The RJ-45 1000BASE-TX Gigabit ports of the Magnum 6K32T can be connected via copper media with th e following minimum specifications; 1000BASE-T, CAT-5e, or for better ...

  • GarrettCom Magnum 6K32T - page 32

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 26 www Garre t t C om c om .. Fiber Port Module Speed, Std. Mode Std. km fdx (hdx) Wave - length nm Cable Size  m X’mitr Output P T , dB R’cvr Sens. P R , dB Worst OPB, dB Worst* distance Km, fdx typical OPB, dB typical* distance Km, fdx 6KP4- F10ST 10Mb FL Multi- Mod ...

  • GarrettCom Magnum 6K32T - page 33

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 27 www Garre t t C om c om .. Magnum Fiber Switch GARRET Magnum PW Managed Switch Magnum 1 3 5 10/100 LK F/H AC 10/100 LK 2 4 6 F/ AC 1 3 5 10/100 LK F/H AC 10/100 LK 2 4 6 F/ AC 1 3 5 10/100 LK F/H AC 10/100 LK 2 4 6 F/ AC Magnum Fiber Switch GARRET Magnum PW Managed Switch ...

  • GarrettCom Magnum 6K32T - page 34

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 28 www Garre t t C om c om .. D D C C BB A D D C C BB A A D D C C BB A A Standard Flush Mount Bracket Mid-Range Mount or Rear Mount Fig 3.3.1 Dual Side-Mountin gs for Magnum 6K32T units These brackets are rack-mounted in a frame typically accessed in operation from both side ...

  • GarrettCom Magnum 6K32T - page 35

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 29 www Garre t t C om c om .. 3.4 Powering the Magnum 6K32T Managed Switch The Magnum 6K32T Switches incorporate an internal universal power supply and have a recessed male IEC connector for the AC power cord at the left-rear. A manual power ON-OFF switch is adjacent. A six- ...

  • GarrettCom Magnum 6K32T - page 36

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 30 www Garre t t C om c om .. 4. By default it is NC (normally closed) 5. The software operation needs to be enabled and set to get the Alarm traps. For detailed information about the Software Alarm and soft ware control of SNMP alarm traps, please reference the Magnum MNS-6 ...

  • GarrettCom Magnum 6K32T - page 37

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 31 www Garre t t C om c om .. Step 2. Remove Chassis Cover The Magnum 6K32T chassis are combined with top, bottom and front panel parts and assembled together with the he lp of 17 Philips-head screws. There are 5 screws located on the front-bottom and 3 at rear-top of the un ...

  • GarrettCom Magnum 6K32T - page 38

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 32 www Garre t t C om c om .. Looking down into the Magnum 6K32T unit, notice that there are individual PM installation spaces and female latch (white) connectors provided on the far right side of main board along with four stand-off’s for 6KPM card position. (See Figure 3 ...

  • GarrettCom Magnum 6K32T - page 39

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 33 www Garre t t C om c om .. Step 2. Placed Granddaughter board (as shown in fig. 3.5.2a and 3.5.2b) on the chassis built in stand off (female) provided at the front of the 6K32T Main Board and screw down tightly with the three 5/16 stand-off (male) on the top of the Grandd ...

  • GarrettCom Magnum 6K32T - page 40

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 34 www Garre t t C om c om .. Step 4. Hold the daughter board with both hands at the end and align the two cream color latching connectors (male) placed at the bottom of the daughter board with the other female connector placed on the Granddaughter and main board. As shown a ...

  • GarrettCom Magnum 6K32T - page 41

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 35 www Garre t t C om c om .. Step 8. Once the 6KPM cards have been insta lled, the chassis top cover should be replaced by matching at the two front corners properly and slide in until it reaches the rear end and fit properly to match the holes. Make sure the chassis cover ...

  • GarrettCom Magnum 6K32T - page 42

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 36 www Garre t t C om c om .. Step 3. Remove 6KPM Card Carefully and gently pull out the daughter boa rd from the latching connectors, using both hands, gripping the board near the latch-up c onnectors as shown in Fig. 3.5.3b . If the now empty slot is to remain unused, be s ...

  • GarrettCom Magnum 6K32T - page 43

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 37 www Garre t t C om c om .. Pin 5 Pin 1 Note: For detail description of Managed Network Software (MNS-6K) and Magnum 6K32T Switch configuration for Network Management, ple a se re fe r to Magnum 6K32T Software Manual available on GarrettCom‘s F TP site. Detail info. abou ...

  • GarrettCom Magnum 6K32T - page 44

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 38 www Garre t t C om c om .. 6K32T, but local traffic on a port will not c onsume any of the bandwidth on any other port. Magnum 6K32T units are plug-and-play devices. There is no software configuring necessary to be done for basic ope ration at installation or for maintena ...

  • GarrettCom Magnum 6K32T - page 45

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 39 www Garre t t C om c om .. 4.3 Up-link Cross-over Switch on RJ-45 port modules, for port#1 only The modular slot provided on Magnum 6K32T managed switch can be filled with 6KP8-RJ45 port module among all the mu ltiple choices of port m odules. The upper part of the copper ...

  • GarrettCom Magnum 6K32T - page 46

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 40 www Garre t t C om c om .. negotiation ports typically will not work pr operly. The 6K32T Switch’s RJ-45 ports handle this situation by configuring the por ts as per desire through MNS software port settings and can check the port status of each port after the change. W ...

  • GarrettCom Magnum 6K32T - page 47

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 41 www Garre t t C om c om .. 4.5 Flow-control, IEEE 802.3x standard Magnum 6K32T Switches incorporate a flow-control mechanism for Full- Duplex mode. The purpose of fl ow-control is to reduce the risk of data loss if a long burst of activity causes the switch to save fra me ...

  • GarrettCom Magnum 6K32T - page 48

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 42 www Garre t t C om c om .. at a later date. In the event there are items missing or dam aged, contact your supplier. If you need to return the unit, use the original shipping container if possible. Refer to Chapter 5 for specific return procedures. 5.2 6KPM Module Descrip ...

  • GarrettCom Magnum 6K32T - page 49

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 43 www Garre t t C om c om .. 6KP4-RJ10MST, 4 Port@ 10Mb ST Fiber Port 2 6 T LK RX ACT F/H TX RX LK ACT F/H TX RX LK ACT F/H TX RX LK ACT F/H 1 5 3 2 1 FULL/HALF 1 ACTIVITY LINK 2 3 Each port has an Activity (ACT) LED indicating packets being received, a Link (LK) LED that i ...

  • GarrettCom Magnum 6K32T - page 50

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 44 www Garre t t C om c om .. 6KP4-RJ10MST, 4 Port@ 10Mb ST Fiber Port 2 6 T LK RX ACT F/H TX RX LK ACT F/H TX RX LK ACT F/H TX RX LK ACT F/H 1 5 3 2 1 FULL/HALF 1 ACTIVITY LINK 2 3 Each port has an Activity (ACT) LED indicating packets being received, a Link (LK) LED indica ...

  • GarrettCom Magnum 6K32T - page 51

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 45 www Garre t t C om c om .. 5.2.2. 6KP6-RJMSC 4@10/100Mbps RJ-45 and 2@100Mb multi-mode FX-SC “snap-in” Fiber connector The Magnum 6KP6- RJMSC is also a Combo 6 Port module equipped with 4 10/100Mb RJ-45 ports along with 2 multi- mode 100Mbps fiber optic transceivers a ...

  • GarrettCom Magnum 6K32T - page 52

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 46 www Garre t t C om c om .. 10/100 LED indicates 100Mbps speed when lit and 10Mbps speed when off. To distinguish the single-mode 6 K6-RJSSC from the multi-mode 6K6-RJMSC, the label “Sgl. M.” is at the top of the faceplate of the 6K6-RJSS C. 5.2.4 6KP6-RJSSCL 4 @ 10/10 ...

  • GarrettCom Magnum 6K32T - page 53

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 47 www Garre t t C om c om .. 5.2.5 6KP8-MTRJ, 8 @100Mb multi-mode FX , MTRJ Small-Form-factor Magnum 6KP8-MTRJ is a multi-mode fiber optic 8-port module equipped with a small-form-factor MTRJ-type connector. It looks almost like an RJ-45 port, but it is black in color. The ...

  • GarrettCom Magnum 6K32T - page 54

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 48 www Garre t t C om c om .. FULL/HALF 1 ACTI VIT Y LINK 2 3 3 2 1 8Por t@ 100Mbp s MLC Por ts - 2 4 6 8 LK LK LK LK ACT F/H ACT F/H ACT F/ H ACT F/H 2 4 6 8 LK LK LK LK ACT F/H ACT F/H ACT F/H ACT F/H 1 3 5 7 FULL/HALF 1 ACTI VIT Y LINK 2 3 3 2 1 8Por t@ 100Mbp s MLC Por t ...

  • GarrettCom Magnum 6K32T - page 55

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 49 www Garre t t C om c om .. 5.2.8 6KP8-45LC, Combo 4@ 100Mbps multi-mode -L C small-form factor and 4@ 10/100 Mbps RJ-45 Connector The Magnum 6KP8- 45LC Module is a combo module with a combination of copper and Fiber (Small Form Factor) LC type ports. The small size of LC ...

  • GarrettCom Magnum 6K32T - page 56

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 50 www Garre t t C om c om .. 4 3 2 4 6 LK 2 ACT F/H ACT F/H 6KP8V - 6KP8 -45-2MT 6 Port @ 10/10Mb p s and 2 port @100Mb Multi -Mode Fiber port 1 3 5 10/10 L 1 F/H AC 4 FULL/HALF 1 ACTIVITY LINK 2 3 10/100 10/100 F/H Link (LK) LED that indicates proper connec tivity with the ...

  • GarrettCom Magnum 6K32T - page 57

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 51 www Garre t t C om c om .. 2SLC is equipped with 6 10/100 RJ-45 ports and 2 Single-mode fiber ports. When installed in a Magnum 6K32T Switch, it supports the standard distances as mentioned on 5.2.4. and the LEDs also act similarly . 5.2.11 GBIC-SXSC Gigabit fiber(1000Mb) ...

  • GarrettCom Magnum 6K32T - page 58

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 52 www Garre t t C om c om .. 1@ 1000Mb Fiber SC + 2@ 100Mb SC The two Giga port has been offered as GBPM -2OTX (fiber or RJ-45), whereas the single Gigabit module comes in flavor of G+4(10/ 100 RJ-45 ports) or G+2 (100Mb fiber ports) as shown below in the above figure. Each ...

  • GarrettCom Magnum 6K32T - page 59

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 53 www Garre t t C om c om .. 5.2.12 6KM-BLNK The 6K8-BLNK is a blank face plate or cover plate that must be installed in any empty 6K32T PM slot to maintain proper cooling air flow, safety, etc. Two screws underneath the front panel hold the 6KM-BLNK in place. 6.0 TROUBLESH ...

  • GarrettCom Magnum 6K32T - page 60

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 54 www Garre t t C om c om .. 5. Always check your Switch configurati on, specially Auto-negotiation behavior with other connected device to have proper setup tested. 5. If the problem continues after comple ting Step 4 above, contact your supplier of the Magnum 6K32T Switch ...

  • GarrettCom Magnum 6K32T - page 61

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 55 www Garre t t C om c om .. Product name Serial Number (or Invoice Number) Packing List Number (or Sales Order Number) Date of installation Failure sy mptoms, including a full description of the problem. GarrettCom will carefully test and evaluate all returned products, wi ...

  • GarrettCom Magnum 6K32T - page 62

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 56 www Garre t t C om c om .. than shipping and handling, provided that the product is returned pre-paid to GarrettCom. This warranty will not be effective if, in the opinion of GarrettCom, the product has been damaged by misuse, misapp lication, or as a result of service or ...

  • GarrettCom Magnum 6K32T - page 63

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 57 www Garre t t C om c om .. The manual power “On-Off” Switch (opti onal) is used for powering the unit on and off when it is placed into or taken out of service. B3.0 APPLICATIONS FOR DC POWERED SWITCHES Magnum 6K32T Fiber Switches are easily in stalled in a variety of ...

  • GarrettCom Magnum 6K32T - page 64

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 58 www Garre t t C om c om .. lead from 48V or –48V supply must be connected to the post labeled “+”. An ON-OFF manual switch is optional for DC power. This can be used to cut off power connections and as a RESET for the Magnum 6K32T Switch. B4.1 UL Requirements for DC ...

  • GarrettCom Magnum 6K32T - page 65

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 59 www Garre t t C om c om .. GND: Terminal for “earth” or ground wire connection to the hub chassis Input: Two separate sources, each at 20 - 36 VDC Power Supply (Internal, 125VDC Du al-Source, model # Dual-Src-24V) DC Power Connector: First Source: “A+”, “A -“ ...

  • GarrettCom Magnum 6K32T - page 66

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 60 www Garre t t C om c om .. reversed while the Switch is operating from the other source. e) The Switch will not receive pow er (and will not work) when both inputs are simultaneously absent or are both incorrectly connected. C5.0 INSTALLATION This section describes the pr ...

  • GarrettCom Magnum 6K32T - page 67

    Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 61 www Garre t t C om c om .. C5.1 UL Requirements The following must be adhered to in or der to conform to UL requirements: 1. Minimum 18 AWG cable for connection to a Centralized DC power source. 2. Minimum 14 AWG cable for connection to earthing wiring. 3. Use only with L ...

Manufacturer GarrettCom Category Switch

Documents that we receive from a manufacturer of a GarrettCom Magnum 6K32T can be divided into several groups. They are, among others:
- GarrettCom technical drawings
- Magnum 6K32T manuals
- GarrettCom product data sheets
- information booklets
- or energy labels GarrettCom Magnum 6K32T
All of them are important, but the most important information from the point of view of use of the device are in the user manual GarrettCom Magnum 6K32T.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals GarrettCom Magnum 6K32T, service manual, brief instructions and user manuals GarrettCom Magnum 6K32T. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product GarrettCom Magnum 6K32T.

Similar manuals

A complete manual for the device GarrettCom Magnum 6K32T, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use GarrettCom Magnum 6K32T by users. Manuals are usually written by a technical writer, but in a language understandable to all users of GarrettCom Magnum 6K32T.

A complete GarrettCom manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual GarrettCom Magnum 6K32T - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the GarrettCom Magnum 6K32T, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the GarrettCom Magnum 6K32T, that we can find in the current document
3. Tips how to use the basic functions of the device GarrettCom Magnum 6K32T - which should help us in our first steps of using GarrettCom Magnum 6K32T
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with GarrettCom Magnum 6K32T
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of GarrettCom Magnum 6K32T in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning GarrettCom Magnum 6K32T?

Use the form below

If you did not solve your problem by using a manual GarrettCom Magnum 6K32T, ask a question using the form below. If a user had a similar problem with GarrettCom Magnum 6K32T it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)