English dropdown-ico

Manual Jonsered LT2226 A2

28 pages 1.84 mb
Download

Go to site of 28

Summary
  • Jonsered LT2226 A2 - page 1

    03090 L T2226 A2 Operator's Manual J O N S E R E D S E R V I C E ...

  • Jonsered LT2226 A2 - page 2

    2 I. GENERAL OPERA TION • Read, understand, and follow all instructions on the machine and in the manual before starting. • Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times. • Only allow responsible adults, who are familiar with the in struc tions, to operate the machine. • ...

  • Jonsered LT2226 A2 - page 3

    3 • Be sure the area is clear of bystanders before operat- ing. Stop machine if anyone enters the area. • Never carry passengers. • Do not mow in reverse unless absolutely necessary . Al ways look down and behind before and while back- ing. • Never carry children, even with the blades shut off. They may fall off and be seriously injured or ...

  • Jonsered LT2226 A2 - page 4

    4 SAFETY RULES ......................................................... 2-3 PRODUCT SPECIFICA TIONS ....................................... 4 CUSTOMER RESPONSIBILITIES ................................. 4 ASSEMBL Y ................................................................. 5-6 OPERA TION ...................................................... ...

  • Jonsered LT2226 A2 - page 5

    5 UNAS SEMBLED P ARTS (2) Keys Slope Sheet Key (1) Oil Drain Tube AS SEMBL Y When right or left hand is mentioned in this man ual, it means when you are in the operating po si tion (seated be hind the steer ing wheel). TO REMOVE TRACTOR FROM CAR TON UNP ACK CARTON • Remove all accessible loose parts and parts cartons from carton. • Cut along da ...

  • Jonsered LT2226 A2 - page 6

    6 AS SEMBL Y CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown on tires. CHECK DECK LEVELNESS For best cutting results, mower housing should be prop- erly leveled. See “TO LEVEL MOWER HOUSING? ...

  • Jonsered LT2226 A2 - page 7

    7 OPERA TION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models only) KEEP AREA CLEAR SLOPE HAZARDS 15 15 (SEE SAFETY RULES SECTION) BATTERY REVERSE FORWARD FAST SLOW ENGINE ON ENGINE OFF FUEL CHOKE MOWER HEIGHT REVERS ...

  • Jonsered LT2226 A2 - page 8

    8 OPERA TION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERA TING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference. Our tractors conform to the applicable safety standards of the American Nati ...

  • Jonsered LT2226 A2 - page 9

    9 OPERA TION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor or per form ing any ad just ments or repairs. We rec om mend standard safety glasses or a wide vision safety mask worn over spectacles. TO USE T ...

  • Jonsered LT2226 A2 - page 10

    10 OPERA TION TO ADJUST MOWER CUT TING HEIGHT (See Fig. 7) The po si tion of the at tach ment lift le ver (A) de ter mines the cut ting height. • Put attachment lift lever in desired cutting height slot. The cutting height range is ap prox i mate ly 1" to 4". The heights are measured from the ground to the blade tip with the engine not ...

  • Jonsered LT2226 A2 - page 11

    11 OPERA TION Fig. 11 TOWING CARTS AND OTHER A T T ACH MENTS T ow only the attachments that are recommended by and comply with specifications of the manufacturer of your trac- tor . Use common sense when towing. T oo heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tracto ...

  • Jonsered LT2226 A2 - page 12

    12 OPERA TION PURGE TRANSMISSION CAUTION: Never engage or disengage freewheel lever while the engine is run ning. T o ensure proper operation and performance, it is rec om - mend ed that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have de- vel o ...

  • Jonsered LT2226 A2 - page 13

    13 Fig. 12 MOWING TIPS • Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trim- ming. • Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of ...

  • Jonsered LT2226 A2 - page 14

    14 MAINTENANCE T R A C T 0 R Inspect Muffler/Spark Arrester Clean Air Filter Change Engine Oil (with oil filter) Replace Air Filter Paper Cartridge Replace Spark Plug Check Engine Oil Level Clean Engine Cooling Fins Clean Air Screen 1 - Change more often when operating under a heavy load or in high ambient temperatures. 2 - Service more often when ...

  • Jonsered LT2226 A2 - page 15

    15 MAINTENANCE Fig. 13 MANDREL ASSEMBL Y BL ADE BL ADE BOL T (SPECIAL) CENTER HOLE ST AR BA TTERY Y our tractor has a battery charging system which is suf fi cient for normal use. However , periodic charging of the battery with an automotive charger will extend its life. • Keep battery and terminals clean. • Keep battery bolts tight. • Keep s ...

  • Jonsered LT2226 A2 - page 16

    16 MAINTENANCE V -BEL TS Check V -belts for deterioration and wear after 100 hours of operation and replace if necessary . The belts are not ad just able. Re place belts if they begin to slip from wear . TRANSAXLE COOLING The transmission fan and cooling fins should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission ...

  • Jonsered LT2226 A2 - page 17

    17 MAINTENANCE MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or dam- age. SP ARK PLUGS Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in “PROD UCT SPECIFICA TIONS ...

  • Jonsered LT2226 A2 - page 18

    18 SERVICE AND ADJUSTMENTS WARNING: TO A VOID SERIOUS INJURY , BEFORE PERFORMING ANY SER VICE OR AD JUST - MENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • T urn ignition key to “STOP” and remove key . • Make sure the blades and all moving parts have completely stopped. ...

  • Jonsered LT2226 A2 - page 19

    19 M C D A E F B SERVICE AND ADJUSTMENTS Fig. 18 Fig. 19 Fig. 20 • A TT ACH FRONT LINK (E) - Work from left side of trac- tor . Insert rod end of link assembly through front hole in tractor front suspension bracket (F). • Insert end of link (E) into hole in front mower bracket (H) and secure with washer and retainer spring (J). E F H J M • In ...

  • Jonsered LT2226 A2 - page 20

    20 SERVICE AND ADJUSTMENTS • If adjustment is necessary , see step in Visual Adjust- ment instructions above. • Recheck measurements, adjust if necessary until both sides are equal. FRONT - TO -BACK ADJUSTMENT (See Figs. 25 and 26) IMPORT ANT : Deck must be level side-to-side. T o obtain the best cutting re sults, the mower blades should be adj ...

  • Jonsered LT2226 A2 - page 21

    21 SERVICE AND ADJUSTMENTS TO REPL ACE MOTION DRIVE BEL T (See Fig. 28) P ark the tractor on level surface. En gage parking brake. For as sis tance, there is a belt installation guide decal on bottom side of left footrest. BEL T REMOV AL - • Remove mower (See “TO RE MOVE MOWER” in this section of manual). NOTE: Observe entire motion drive bel ...

  • Jonsered LT2226 A2 - page 22

    22 SERVICE AND ADJUSTMENTS Fig. 29 RE T AIN ING RING WASH ERS SQUARE KEY (REAR WHEEL ONL Y) AXLE COVER TO ST ART ENGINE WITH A WEAK BA TTERY (See Fig. 30) WARNING : Lead-acid batteries gen- er ate ex plo sive gases. Keep sparks, flame and smoking ma te ri als away from bat ter ies. Always wear eye pro tec tion when around batteries. If your battery ...

  • Jonsered LT2226 A2 - page 23

    23 SERVICE AND ADJUSTMENTS TO REPL ACE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill. • Close hood. INTERL OCKS AND REL A YS Loose or damaged wiring may cause your tractor to run poorly , sto ...

  • Jonsered LT2226 A2 - page 24

    24 STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any en clo sure. TRACTOR Remove mower from t ...

  • Jonsered LT2226 A2 - page 25

    25 TROUBLESHOOTING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “TO ST ART ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug. 4. Replace spark plug. 5. Weak or dead battery . 5. Recharge or replace battery . 6. Dirty air ...

  • Jonsered LT2226 A2 - page 26

    26 TROUBLESHOOTING POINTS Engine dies when 1. Reverse operation system 1. T urn ignition key to tractor is shifted (ROS) is not "ON" while ROS "ON" position. into reverse mower or other attachment See Operation section. is engaged. Engine continues to run 1. F aulty operator-safety presence control system. 1. Check wiring, switc ...

  • Jonsered LT2226 A2 - page 27

    27 15 DEGREES MAX. FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees. Make turns gradually to preven ...

  • Jonsered LT2226 A2 - page 28

    Jonsered Motor AB, S-433 81 Partille, Sweden. 532 41 94-10 Rev . 1 06.23.08 SBW Printed in U.S.A. ...

Manufacturer Jonsered Category Lawn Mower

Documents that we receive from a manufacturer of a Jonsered LT2226 A2 can be divided into several groups. They are, among others:
- Jonsered technical drawings
- LT2226 A2 manuals
- Jonsered product data sheets
- information booklets
- or energy labels Jonsered LT2226 A2
All of them are important, but the most important information from the point of view of use of the device are in the user manual Jonsered LT2226 A2.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Jonsered LT2226 A2, service manual, brief instructions and user manuals Jonsered LT2226 A2. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Jonsered LT2226 A2.

Similar manuals

A complete manual for the device Jonsered LT2226 A2, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Jonsered LT2226 A2 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Jonsered LT2226 A2.

A complete Jonsered manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Jonsered LT2226 A2 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Jonsered LT2226 A2, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Jonsered LT2226 A2, that we can find in the current document
3. Tips how to use the basic functions of the device Jonsered LT2226 A2 - which should help us in our first steps of using Jonsered LT2226 A2
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Jonsered LT2226 A2
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Jonsered LT2226 A2 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Jonsered LT2226 A2?

Use the form below

If you did not solve your problem by using a manual Jonsered LT2226 A2, ask a question using the form below. If a user had a similar problem with Jonsered LT2226 A2 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)