English dropdown-ico

Manual GE ZBD7105

16 pages 0.44 mb
Download

Go to site of 16

Summary
  • GE ZBD7105 - page 1

    Monogram. We bring good things to life. ® If you have questions , call 800.626.2000 or visit our website at: www .monogram.com Installation Instr uctions Built-In Dishwashers ZBD6400, ZBD6500, ZBD6600 ZBD6700, ZBD6900, ZBD7000, ZBD7100 Chef’ s W ashers ZBD6605, ZBD6905, ZBD7005, ZBD7105 Design Guide with Installation Instructions ...

  • GE ZBD7105 - page 2

    Safety Information • IMPOR T ANT – The dishwasher MUST be installed to allow for future removal from the enclosure if ser vice is required. If you received a damaged dishwasher , you should immediately contact your dealer or builder . READ CAREFULL Y . KEEP THESE INSTRUCTIONS. FOR YOUR SAFETY Read and obser ve all CAUTION and W ARNINGS shown th ...

  • GE ZBD7105 - page 3

    Design Information 3 ADV ANCE PLANNING • These dishwashers are designed for versatility , adaptable to virtually any installation. • All models have a full length door or a modified door to accept a full cabinet panel without the traditional access panel • Side tub flange trim is adjustable and will conceal any slight gap between the dishwash ...

  • GE ZBD7105 - page 4

    Installation Preparation MA TERIALS YOU WILL NEED: Materials Required for All Installations ¨ 90 ° Elbow (3/8”NPT external thread on one end, opposite end sized to fit water supply) Note: Use new ferrule. Do not use old parts. ¨ Strain relief for electrical connection ¨ Thread seal tape ¨ UL Listed wire connectors (3) ¨ Screw type hose clam ...

  • GE ZBD7105 - page 5

    Installation Preparation P ARTS SUPPLIED: Remove the hardware accessor y bag and other parts from inside or taped to the outside of the dishwasher . Check contents against illustrations to insure that all parts are included. ¨ 2-piece toekick ¨ 6 screws (see illustration) ¨ 2 leveling legs ¨ T emplate for the installation of a custom panel pack ...

  • GE ZBD7105 - page 6

    DRAIN REQUIREMENTS • Follow local codes and ordinances. • Do not exceed 10 feet distance to drain. • T o prevent back flow into the dishwasher , connect drain line to an air gap or use a 30” high drain loop, depending on local codes. • Air gap must be used when waste tee or disposer connection is less than 18” above the floor to prevent ...

  • GE ZBD7105 - page 7

    Installation Preparation 7 PREP ARE ELECTRICAL WIRING FOR PERSONAL SAFETY: Remove house fuse or open circuit breaker before beginning installation. Do not use an extension cord or adapter plug with this appliance. Electrical Requirements • This appliance must be supplied with 120V , 60 Hz., and connected to an individual properly grounded branch ...

  • GE ZBD7105 - page 8

    Installation Preparation 8 PREP ARE HOT W A TER LINE The line may enter from either side, rear or floor within the shaded area shown. • The water line may pass through the same hole as the electrical cable and drain hose. Or , cut an additional 1-1/2" dia. hole to admit the line. If a power cord with plug is used, it must pass through a sepa ...

  • GE ZBD7105 - page 9

    Custom Panel Dimensions 9 CUSTOM P ANEL FOR MODELS ZBD6400 ONL Y Panel kits must be ordered separately . Installation of any custom panel should be completed before the dishwasher is installed. 1/4" P ANEL WITH ZPF625 TRIM KIT CUSTOM P ANEL FOR MODELS ZBD7000 AND ZBD7005 These models require a field installed 3/4" thick custom panel and c ...

  • GE ZBD7105 - page 10

    10 Installation Instructions BEFORE YOU BEGIN: CUSTOM P ANEL INSTALLA TION: If you intend to install custom door panels, (on some models) refer to trim kit installation instr uctions. Custom panels should be in place before installing the dishwasher . STEP 2 INST ALL LEVELING LEGS STEP 1 REMOVE P ACKAGING Cut the shipping carton and use it as a pad ...

  • GE ZBD7105 - page 11

    Installation Instructions 11 STEP 5 INST ALL POWER CORD SKIP THIS STEP IF DISHW ASHER WILL BE DIRECT WIRED • Maximum power cord length is 6 ft. • The power cord and connections must comply with the National Electrical Code, Section 422 and/or local codes and ordinances. Insert power cord wires through strain relief and tighten. STEP 6 LEVEL DIS ...

  • GE ZBD7105 - page 12

    Installation Instructions 12 STEP 9 CONNECT DRAIN LINE FOLLOW ALL LOCAL CODES AND ORDINANCES. • The dishwasher is supplied with a 72" long drain hose. • If a longer drain hose is required, add up to 48” of length for a total of 10 ft. length. • Secure the drain hose to the air gap, waste tee or disposer with clamps. • Make sure drain ...

  • GE ZBD7105 - page 13

    13 Installation Instructions STEP 11 POSITION AND LEVEL THE DISHWASHER U N S C R E W Adjust This Leg Door Rub On Right Hand Side U N S C R E W Adjust This Leg Door Rub On Left Hand Side STEP 12 PRE-TEST CHECK LIST Installation service calls are not covered by your warranty . T o avoid unnecessary charges, review this list carefully . ¨ Check to be ...

  • GE ZBD7105 - page 14

    14 Installation Instructions STEP 14 SECURE DISHW ASHER TO CABINET AND COUNTER TOP T o maintain position and alignment, the dishwasher must be secured to the countertop and adjacent cabinets. Secure dishwasher to countertop: • Drill pilot holes through the mounting bracket and into the underside of the countertop. Secure with screws A provided. I ...

  • GE ZBD7105 - page 15

    15 Panel Installation for Models ZBD7000 and ZBD7005 The custom panel should be prepared by your cabinet manufacturer according to the instructions shown on page 9. Use the supplied installation template to locate the mounting screws for the door . STEP 1 DRA W CENTERLINE • Place the custom panel on a flat sur face with appearance side down. • ...

  • GE ZBD7105 - page 16

    Note: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram TM local service in your area, call 1-800-444-1845. Note: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. Monogram. ® General ...

Manufacturer GE Category Computer Drive

Documents that we receive from a manufacturer of a GE ZBD7105 can be divided into several groups. They are, among others:
- GE technical drawings
- ZBD7105 manuals
- GE product data sheets
- information booklets
- or energy labels GE ZBD7105
All of them are important, but the most important information from the point of view of use of the device are in the user manual GE ZBD7105.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals GE ZBD7105, service manual, brief instructions and user manuals GE ZBD7105. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product GE ZBD7105.

Similar manuals

A complete manual for the device GE ZBD7105, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use GE ZBD7105 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of GE ZBD7105.

A complete GE manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual GE ZBD7105 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the GE ZBD7105, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the GE ZBD7105, that we can find in the current document
3. Tips how to use the basic functions of the device GE ZBD7105 - which should help us in our first steps of using GE ZBD7105
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with GE ZBD7105
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of GE ZBD7105 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning GE ZBD7105?

Use the form below

If you did not solve your problem by using a manual GE ZBD7105, ask a question using the form below. If a user had a similar problem with GE ZBD7105 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)