English dropdown-ico

Manual Hobart HGC3632

24 pages 2.34 mb
Download

Go to site of 24

Summary
  • Hobart HGC3632 - page 1

    MODEL HGC SERIES GAS CONVEYOR OVENS MODELS HGC3018 ML-126180 HGC4018 ML-126181 HGC3624 ML-126182 HGC3632 ML-126183 HGC4824 ML-126184 HGC4832 ML-126185 HGC6024 ML-126186 HGC6032 ML-126187 FORM 34069 (6-98) 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 ...

  • Hobart HGC3632 - page 2

    — 2 — IMPORT ANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE OB ...

  • Hobart HGC3632 - page 3

    — 3 — T ABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Unpacking . . . . . . . . ...

  • Hobart HGC3632 - page 4

    — 4 — Installation, Operation and Care of MODEL HGC SERIES GAS CONVEYOR OVENS PLEASE KEEP THIS MANUAL FOR FUTURE USE GENERAL Hobart ovens are produced with quality workmanship and material. Proper installation, usage and maintenance of your oven will result in many years of satisfactory performance. It is suggested that you thoroughly read this ...

  • Hobart HGC3632 - page 5

    — 5 — LOCATION When the crate is turned on its side, the oven will pass through a 34" (86 cm) door opening (or 30" [76 cm] opening without the crate). Verify that the doors and access routes into the kitchen area will permit clearance. The equipment area must be kept free and clear of combustible substances. When installed, minimum cl ...

  • Hobart HGC3632 - page 6

    — 6 — INSTALLATION CODES AND STANDARDS The oven must be installed in accordance with: In the United States of America: 1. State and local codes. 2. National Fuel Gas Code, ANSI-Z223.1 (latest edition). Copies may be obtained from The American Gas Association, Inc., 1515 Wilson Blvd., Arlington, VA 22209. 3. National Electrical Code, ANSI/NFPA-7 ...

  • Hobart HGC3632 - page 7

    — 7 — CONNECT GAS LINE STRAIN RELIEF HERE ASSEMBLY Ovens Mounted on Legs or Feet To service the oven when mounted on legs or feet, a minimum clearance of 18" (457 mm) from service compartment is required. Ovens Mounted on Casters NOTICE: In order to be able to service this appliance, it must be installed with the casters supplied, a connec ...

  • Hobart HGC3632 - page 8

    — 8 — Installing Stacked Ovens After basic oven is installed: • Lift the top oven and place it on top of the bottom oven. • No fasteners are required; the weight of the oven will keep it in place. LEVELING Casters for this oven are of the non-adjustable type. For best results, oven should be installed on a level floor. GAS CONNECTIONS Gas s ...

  • Hobart HGC3632 - page 9

    — 9 — ELECTRICAL CONNECTIONS WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING: APPLIANCES EQUIPPED WITH A FLEXIBLE ELECTRIC SUPPLY CORD ARE PROVIDED WITH A THREE-PRONG GROUNDING PLUG. IT IS IMPERATIVE THAT THIS PLUG BE CONNECTED IN ...

  • Hobart HGC3632 - page 10

    — 10 — PL-41 155-1 SET POINT CYCLE TIME MAN. RESET PROP . BAND DOOR FLAP PL-41 154-1 TEMPERA TURE DISPLA Y LOAD INDICA T OR LIGHT TIME DISPLA Y BEL T SWITCH TIME KNOB POWER SWITCH TIME RANGE SWITCH READ SET POINT BUTT ON Fig. 3 OPERA TION WARNING: THE OVEN AND ITS PARTS ARE HOT. BE VERY CAREFUL WHEN OPERATING, CLEANING OR SERVICING THE OVEN. CO ...

  • Hobart HGC3632 - page 11

    — 11 — Temperature Display — Displays actual oven cavity temperature during cooking cycle. Read Set Point Button — Push to display set temperature. Load Indicator Light — When lit, indicates that the heat is being provided to the oven. Time Display — Displays actual cooking time in minutes and tenths of minutes. Time Range Switch — Us ...

  • Hobart HGC3632 - page 12

    — 12 — PL-41 156-1 TIME DISPLA Y TEMPERA TURE DISPLA Y BEL T SWITCH TIME KNOB POWER SWITCH SET POINT TIME RANGE SWITCH SET POINT ARROWS CONTROL CIRCUIT FUSE DRIVE MOTOR FUSES SET POINT INDICA T OR LIGHT ALTERNATE CONTROLS (Fig. 4) Fig. 4 ...

  • Hobart HGC3632 - page 13

    — 13 — Temperature Display — Displays actual oven cavity temperature during cooking cycle. Set Point — Press to display set temperature. Set Point Arrows — 1. Press the Set Point button so that the set point is displayed, and at the same time, press the Set Point Arrows up or down until the desired set point temperature appears in the dig ...

  • Hobart HGC3632 - page 14

    — 14 — PL-41125-1 GAS COMBINA TION CONTROL V AL VE BEFORE FIRST USE 1. Clean the protective metal oils from all surfaces of the oven. 2. Use a non-corrosive, grease dissolving commercial cleaner. Follow manufacturer's directions. 3. Rinse thoroughly with a clean damp cloth and wipe dry with a soft clean cloth. • DO NOT hose down the oven ...

  • Hobart HGC3632 - page 15

    — 15 — PL-41 126-1 THUMB SCREWS BAFFLE Extended Shutdown 1. Turn Power Switch to OFF. 2. Turn gas combination valve to OFF. 3. Turn main gas shutoff valve to OFF. USING THE OVEN 1. Turn the main power switch ON. • The oven will begin operating at the factory set temperature of 525 ° F (273 ° C). • The actual oven cavity temperature will a ...

  • Hobart HGC3632 - page 16

    — 16 — Loading and Unloading the Oven 1. Place product in utensils (if required). 2. Set utensils or products on the entrance end of the belt; not in the oven tunnel. 3. Remove utensils or products from the oven after they completely clear the oven tunnel. Air Distribution Panels The oven is equipped with a top and a bottom air distribution pan ...

  • Hobart HGC3632 - page 17

    — 17 — Fig. 7 CLEANING WARNING: DISCONNECT ELECTRICAL POWER SUPPLY BEFORE CLEANING. Daily Clean the outside of the oven daily by wiping with a clean damp cloth. • Avoid using abrasive powders or pads; these cleaners may damage the finish. Clean right-hand and left-hand crumb trays (Fig. 7). 1. Remove and wash in a sink as you would any normal ...

  • Hobart HGC3632 - page 18

    — 18 — Conveyor To maintain proper belt tension, adjust the conveyor belt to remove any slack. 1. Locate the two adjustment screws (Fig. 8) on the right hand end (facing machine) of the conveyor assembly. 2. Loosen the nuts on the inside of the conveyor rack and turn the adjusting screws clockwise to increase belt tension. Be sure to adjust bot ...

  • Hobart HGC3632 - page 19

    — 19 — 2. Conveyor Assembly Removal a. Remove conveyor crumb trays (see Fig. 7). b. Remove cover where conveyor shaft enters the left-hand control box (Fig. 9). Fig. 9 Fig. 10 c. Lift up the drive end of the conveyor assembly and slide the conveyor assembly into the oven tunnel to remove the tension on the drive chain. d. Slip the drive chain o ...

  • Hobart HGC3632 - page 20

    — 20 — Weekly CAUTION: Intake fans and slots on the back of the oven and control box must be cleaned weekly. Any obstructions may cause motor damage. Use a long bristle brush to clean these areas. Fig. 11 e. Pull the entire conveyor assembly from the oven (Fig. 11). f. Take conveyor assembly to cleaning area. g. Reverse this procedure to replac ...

  • Hobart HGC3632 - page 21

    — 21 — CONVEYOR BELT ASSEMBLING AND DISASSEMBLING (Fig. 12) Install the conveyor belt so that it always runs in the direction indicated by this arrow — the closed end of the loop toward the direction of travel. The arrows in the belt illustrate the movement of the splicing strand between steps. When bending the splicing strand, try to limit b ...

  • Hobart HGC3632 - page 22

    — 22 — COOKING CHART The times and temperatures shown in this chart are suggested only. Experiment with your food products to determine the cooking temperatures and times that give you the best results. TYPE OF APPROX. TIME TEMP. FOOD PRODUCT (IN MIN.) ( ° F) / ( ° C) ITALIAN Pizza (par baked dough) 4 to 4.5 510 / 265 Pizza (fresh dough) 5.5 ...

  • Hobart HGC3632 - page 23

    — 23 — MAINTENANCE WARNING: THE OVEN AND ITS PARTS ARE HOT. BE VERY CAREFUL WHEN OPERATING, CLEANING OR SERVICING THE OVEN. WARNING: DISCONNECT ELECTRICAL POWER SUPPLY BEFORE PERFORMING ANY MAINTENANCE ON THE OVEN. INSPECTION The oven should be inspected at least annually by a Hobart authorized servicer. More frequent cleaning may be required d ...

  • Hobart HGC3632 - page 24

    — 24 — TROUBLESHOOTING GUIDE PROBLEM Power switch is on and oven will not operate. Burner is on but oven does not start. Speed control shows "OL". Conveyor belt does not turn. Conveyor belt jumps. Burner does not ignite. Cooking is not even. Oven gives off gas odors. Oven is operating, temperature controller is on, and the burner goes ...

Manufacturer Hobart Category Oven

Documents that we receive from a manufacturer of a Hobart HGC3632 can be divided into several groups. They are, among others:
- Hobart technical drawings
- HGC3632 manuals
- Hobart product data sheets
- information booklets
- or energy labels Hobart HGC3632
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hobart HGC3632.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hobart HGC3632, service manual, brief instructions and user manuals Hobart HGC3632. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hobart HGC3632.

Similar manuals

A complete manual for the device Hobart HGC3632, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hobart HGC3632 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hobart HGC3632.

A complete Hobart manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hobart HGC3632 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hobart HGC3632, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hobart HGC3632, that we can find in the current document
3. Tips how to use the basic functions of the device Hobart HGC3632 - which should help us in our first steps of using Hobart HGC3632
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hobart HGC3632
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hobart HGC3632 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hobart HGC3632?

Use the form below

If you did not solve your problem by using a manual Hobart HGC3632, ask a question using the form below. If a user had a similar problem with Hobart HGC3632 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)