English dropdown-ico

Manual Crunch GTO2120

32 pages Not applicable
Download

Go to site of 32

Summary
  • Crunch GTO2120 - page 1

    2-KANAL VERSTÄRKER 2 CHANNEL AMPLIFIER AMPLIFICA TEUR 2 CANAUX AMPLIFICA TORE 2 CANALI AMPLIFICADOR DE 2 CANALES BEDIENUNGSANLEITUNG USER’S MANUAL MODE D’EMPLOI MANUALE D’USO MANUAL DE USO GTO 2 1 20 ...

  • Crunch GTO2120 - page 2

    DEU ENG FRA ITA ESP 3 8 13 18 23 ABBILDUNGEN / FIGURES / FIGURES / FIGURE / FIGURES 28 BEDIENUNGSANLEITUNG USER’S MANUAL MODE D’EMPLOI MANUALE D´USO MANUAL DE USO INHALTSVERZEICHNIS TABLE OF CONTENT TABLE DES MATIÈRES SOMMARIO INDICE ...

  • Crunch GTO2120 - page 3

    GTO2120 2 x 70 W an 4 Ohm 2 x 120 W an 2 Ohm 2 x 140 W an 4 Ohm 2 x 240 W an 2 Ohm 2 – 8 Ohm 10 Hz – 40 kHz (-3 dB) < 0,2 % (1 kHz) > 92 dB 6 – 0,2 V Cinch 20 kOhm / High Level 200 Ohm 50 – 250 Hz @ 12 dB/Oktave 50 – 250 Hz @ 12 dB/Oktave 0 – 12 dB @ 45 Hz +12 V (12 – 16 V), Minus an negativer Masse 20 A 135 x 50 x 160 mm 3 DEU ...

  • Crunch GTO2120 - page 4

    4 DEU HINWEISE VOR DER INSTALLATION - Dieser Verstärker ist nur zum Betrieb in einem Fahrzeug geeignet. - Dieser Verstärker ist nur zum Anschluss an ein 12-Volt-System mit negativer Masse geeignet. - Die während des Betriebs abgestrahlte Wärme erfordert einen Montageort mit ausreichender Luftzirkulation. Es ist sehr wichtig, dass die Kühlrippe ...

  • Crunch GTO2120 - page 5

    5 DEU ANSCHLUSS EINES WEITEREN VERSTÄRKERS Aufgrund seiner kompakten Bauform hat der Verstärker keine Signalausgänge für den Anschluss weiterer Verstärker, wie zum Beispiel einen Mono-Subwoofer-Verstärker. Benutzen Sie in diesem Falle Y-Adapter aus dem Fachhandel um das Eingangssignal (Cinch/RCA-Kabel vom Steuergerät) entsprechend zu splitte ...

  • Crunch GTO2120 - page 6

    6 DEU Sollte der Verstärker zum Betreiben von Satellitenlautsprechern (Mittel-/ Hochton-Lautsprecher) benutzt werden, stellen Sie den Schalter (X-OVER, Abb.1, 5) auf „HPF“ oder bei großen Lautsprechern ab 20 cm auf ”FULL”. Stellen Sie am Regler (LPF/HPF, Abb.1, 6) die gewünschte Trennfrequenz ein. Somit werden nur die Frequenzen oberhalb ...

  • Crunch GTO2120 - page 7

    2-KANAL-BETRIEB STEREO (ABB. 3) Wenn der Verstärker von einem Steuergerät mit 2 Ausgangskanälen angesteuert wird, um damit 2 Lautsprecher in Stereo zu betreiben, sind die Anschlüsse folgendermaßen vorzunehmen: (1) Stereo Audiosignal-Hochpegeleingänge für die Lautsprecherausgänge vom Steuergerät (2) Zum Steuergerät, Audiosignal-Ausgang rec ...

  • Crunch GTO2120 - page 8

    8 ENG GTO2120 2 x 70 W @ 4 Ohms 2 x 120 W @ 2 Ohms 2 x 140 W @ 4 Ohms 2 x 240 W @ 2 Ohms 2 – 8 Ohms 10 Hz – 40 kHz (-3 dB) < 0,2 % (1 kHz) > 92 dB 6 – 0,2 V RCA 20 kOhms / High Level 200 Ohms 50 – 250 Hz @ 12 dB/Octave 50 – 250 Hz @ 12 dB/Octave 0 – 12 dB @ 45 Hz +12 V (12 – 16 V), negative ground 20 A 135 x 50 x 160 mm WARRANTY ...

  • Crunch GTO2120 - page 9

    9 ENG IMPORTANT NOTES PRIOR TO INSTALLATION - This device is only suited for the operation in a vehicle. - This device is only suited for a 12 volt system with negative ground. - The radiated heat while operation requires sufficient air circulation at the place of installation. It is very important that the heatsink fins do not have contact with an ...

  • Crunch GTO2120 - page 10

    10 ENG LOUDSPEAKER CONNECTIONS - In 2-channel operation (i.e. one loudspeaker on each amplifier channel), the impedance must not be lower than 2 ohms for each speaker - In bridging mode (two amplifier outputs combined) the impedance must not be lower than 4 ohms for the bridged output. - Never connect loudspeaker cables with the ground of the chass ...

  • Crunch GTO2120 - page 11

    11 ENG POWER SUPPLY AND TURN ON CONNECTION (FIG. 2) (1) +12 V terminal for the positive-connection of the battery (2) REM terminal for the turn on connection (3) GND terminal for the ground (4) Vehicle’s battery (5) In-Line Fuse (not included in the scope of delivery) (6) Turn on wire from the headunit or the electrical antenna (7) Protection-LED ...

  • Crunch GTO2120 - page 12

    12 ENG 2-CHANNEL OPERATION STEREO (FIG. 3) If you want to run the amplifier with the 2 line output channels from the headunit to drive 2 loudspeakers, in stereo connect the following setup: (1) Stereo high level input for loudspeaker outputs from the headunit (2) RCA audio signal input from the headunit, line output right (3) RCA audio signal input ...

  • Crunch GTO2120 - page 13

    13 FRA GTO2120 2 x 70 W @ 4 Ohm 2 x 120 W @ 2 Ohm 2 x 140 W @ 4 Ohm 2 x 240 W @ 2 Ohm 2 – 8 Ohm 10 Hz – 40 kHz (-3 dB) < 0,2 % (1 kHz) > 92 dB 6 – 0,2 V RCA 20 kOhm / High Level 200 Ohm 50 – 250 Hz @ 12 dB/Octave 50 – 250 Hz @ 12 dB/Octave 0 – 12 dB @ 45 Hz +12 V (12 – 16 V), négatif à la masse 20 A 135 x 50 x 160 mm Veuillez ...

  • Crunch GTO2120 - page 14

    14 FRA RECOMMANDATIONS AVANT L’INSTALLATION - Cette appareil est conçu uniquement pour un fonctionnement dans un véhicule. - Cet appareil convient exclusivement au branchement à un système de 12 volt à masse négative. - La chaleur provenant de l’utilisation nécessite un espace de montage avec une circulation de l’air suffisante. Il est ...

  • Crunch GTO2120 - page 15

    15 FRA BRANCHEMENTS DES HAUT-PARLEURS - En mode 2 canaux (un pour chaque canal de l´amplificateur), l´impédance ne doit pas être inférieure á 2 ohms par haut parleur. - En mode ponté (c.a.d chacune des 2 sorties de l´ampli sont branchées ensembles) l´impédance ne doit pas être inférieure á 4 ohms. - Ne raccordez jamais les bornes des ...

  • Crunch GTO2120 - page 16

    16 FRA Dans le cas où l´amplificateur est utilisé comme amplificateur pour haut-parleurs satellites (haut-parleurs médium/aigu), positionnez le selecteur (X-OVER, Fig. 1, 5) sur "HPF"ou sur "FULL" pour les haut- paleurs >20cm. Ajustez le régulateur (HPF/LPF, Fig. 1, 6) sur la fréquence de recouvrement souhaitée. De cet ...

  • Crunch GTO2120 - page 17

    17 FRA FONCTIONNEMENT 2 CANAUX STEREO (FIG. 3) Si l’amplificateur est commandé par un autoradio avec 2 canaux de sortie et connecté à 2 haut-parleurs, dans ce cas là, les branchements et les réglages sont à faire comme décrits la figure 3: (1) Entrée haut niveau facultative pour la sortie haut-parleur de votre autoradio (2) Vers l’autor ...

  • Crunch GTO2120 - page 18

    18 ITA Con riserva di apportare modifiche tecniche GTO2120 2 x 70 W @ 4 Ohm 2 x 120 W @ 2 Ohm 2 x 140 W @ 4 Ohm 2 x 240 W @ 2 Ohm 2 – 8 Ohm 10 Hz – 40 kHz (-3 dB) < 0,2 % (1 kHz) > 92 dB 6 – 0,2 V RCA 20 kOhm / High Level 200 Ohm 50 – 250 Hz @ 12 dB/Octave 50 – 250 Hz @ 12 dB/Octave 0 – 12 dB @ 45 Hz +12 V (12 – 16 V), negativo ...

  • Crunch GTO2120 - page 19

    19 ITA INDICAZIONI IMPORTANTI PRIMA DEL MONTAGGIO - Questo dispositivo é adatto solo per il funzionamento su autovettura - Questo apparecchio é adatto unicamente ad essere collegato con un sistema elettrico a 12 Volt con negativo a massa. - Il calore irradiato durante l’erogazione di potenza richiede un posizionamento con una sufficiente circol ...

  • Crunch GTO2120 - page 20

    20 ITA COLLEGAMENTI ALTOPARLANTI - Nel funzionamento a 2 canali (un altoparlante connesso a ciascun canale dell´amplificatore) l´impedenza di ciascun altoparlante non deve essere inferiore a 2 ohm. - Nel funzionamento a ponte in mono (2 uscite dell´amplificatore combinate) l´impedenza non essere inferiore a 4 ohm. - Non collegare mai i cavi alt ...

  • Crunch GTO2120 - page 21

    21 ITA ALIMENTAZIONE ELETTRICA E IMPIANTO D’ACCENSIONE (FIG. 2) (1) Morsetto +12V per connetore il positivo (2) Morsetto REM per l’accensione a distanza (3) Morsetto GND per connettere la massa (4) Batteria (5) Da collegare Fusibile (non compreso) (6) Da collegare al cavo di accensione dell’autoradio o uscita dell’antenna elettrica (7) LED ...

  • Crunch GTO2120 - page 22

    22 ITA RISOLUZIONE DEI PROBLEMI Se incontraste dei problemi dopo l’installazione,seguite le procedure per la localizzazione e la riparazione dei guasti elencate di sotto. Procedura 1: Controllate che l’amplificatore abbia i collegamenti adeguati. Controllate che la spia dell’ACCENSIONE sia accesa.Se la spia di ACCENSIONE è accesa,passare al ...

  • Crunch GTO2120 - page 23

    23 ESP GTO2120 2 x 70 W @ 4 Ohmios 2 x 120 W @ 2 Ohmios 2 x 140 W @ 4 Ohmios 2 x 240 W @ 2 Ohmios 2 – 8 Ohmios 10 Hz – 40 kHz (-3 dB) < 0,2 % (1 kHz) > 92 dB 6 – 0,2 V RCA 20 kOhmios / High Level 200 Ohmios 50 – 250 Hz @ 12 dB/Octave 50 – 250 Hz @ 12 dB/Octave 0 – 12 dB @ 45 Hz +12 V (12 – 16 V), negativo a tierra 20 A 135 x 50 ...

  • Crunch GTO2120 - page 24

    24 ESP INDICACIONES IMPORTANTES PREVIAS AL MONTAJE - Este aparato solamente es apto para su funcionamiento en un vehículo. - Este equipo es adecuado sólo para la conexión a un sistema de 12 voltios con tierra negativa. - El calor irradiado hace que sea importante que instale el aparato en un lugar con suficiente circulación de aire. Es muy impo ...

  • Crunch GTO2120 - page 25

    25 ESP CONEXIÓN DE ALTAVOCES - Operando en 2 canales (p.e. un altavoz para cada canal) la impedancia nunca debe ser inferior a 2 ohmios por cada altavoz - En modo puenteado (dos salidas combinadas por altavoz) la impedancia no debe ser inferior a 4 ohmios. - Nunca conecte los cables del atavoz a la masa del chasis o la fuente de alimentación de b ...

  • Crunch GTO2120 - page 26

    26 ESP Si el amplificador se usará para un subwoofer colocar el selector en posición "LPF" (X-OVER, Fig. 1, 5). Seleccionar el corte de frecuencia deseado en el regulador (LPF/HPF, Fig. 1, 6). De esta forma, solo las frecuencias por debajo del corte serán amplificadas y el Subwoofer funcionará más preciso y eficientemente. FILTRO DE ...

  • Crunch GTO2120 - page 27

    27 ESP FUNCIONAMIENTO DE 2 CANALES STEREO (FIG. 3) Si el amplificador de la radio del coche funciona con 2 canales y está conectado a 2 altavoces, deberá realizar las conexiones y los ajustes como se indica en la figura 3: (1) Entrada alta opcional para las salidas de altavoces de su unidad de Radio-CD (2) A la radio del coche, salida izquierda ( ...

  • Crunch GTO2120 - page 28

    28 + – 4 1 4 3 1 2 5 6 2 2 3 1 6 5 7 ...

  • Crunch GTO2120 - page 29

    29 3 HPF FULL 2 3 1 5 4 2 - 8 Ohms 2 - 8 Ohms ...

  • Crunch GTO2120 - page 30

    30 4 LPF 2 3 1 4 - 8 Ohms 4 ...

  • Crunch GTO2120 - page 31

    ...

  • Crunch GTO2120 - page 32

    Audio Design GmbH · www.crunchaudio.de Am Breilingsweg 3 · D-76709 Kronau (Germany) Tel. +49 (0)7253 - 9465-0 · Fax +49 (0)7253 - 946510 © 2012 Audio Design GmbH, All Rights Reserved. ...

Manufacturer Crunch Category Receiver

Documents that we receive from a manufacturer of a Crunch GTO2120 can be divided into several groups. They are, among others:
- Crunch technical drawings
- GTO2120 manuals
- Crunch product data sheets
- information booklets
- or energy labels Crunch GTO2120
All of them are important, but the most important information from the point of view of use of the device are in the user manual Crunch GTO2120.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Crunch GTO2120, service manual, brief instructions and user manuals Crunch GTO2120. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Crunch GTO2120.

Similar manuals

A complete manual for the device Crunch GTO2120, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Crunch GTO2120 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Crunch GTO2120.

A complete Crunch manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Crunch GTO2120 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Crunch GTO2120, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Crunch GTO2120, that we can find in the current document
3. Tips how to use the basic functions of the device Crunch GTO2120 - which should help us in our first steps of using Crunch GTO2120
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Crunch GTO2120
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Crunch GTO2120 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Crunch GTO2120?

Use the form below

If you did not solve your problem by using a manual Crunch GTO2120, ask a question using the form below. If a user had a similar problem with Crunch GTO2120 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)