English dropdown-ico

Manual Therma-Tru Pre-hung Door Systems

10 pages 0.39 mb
Download

Go to site of 10

Summary
  • Therma-Tru Pre-hung Door Systems - page 1

    Builder or Subcontractor: Please forward these instructions to the homeowner . The applicable performance standards for these products are governed by the International Residential Code. Copies of performance ratings and testing are available on our website at www .thermatru.com and our Product Manual. Constructor o Subcontatista: Favor de entregar ...

  • Therma-Tru Pre-hung Door Systems - page 2

    Check door unit. Check and pr epar e opening. La puerta. Revise y pr epar e el espacio Revise la puerta. Check width and height. Measure size of frame (width and height), not brickmold. Remove cleats and packaging, but keep door fastened closed with transport clip. Do not remove clip or open door until instructed to do so later in step 7. Is subflo ...

  • Therma-Tru Pre-hung Door Systems - page 3

    Check and pr epar e opening. La puerta. Revise y pr epar e el espacio Attach string diagonally across the opening from the outside. The string should gently touch, if not the opening is out of plumb by twice that distance and needs to be corrected. . Flip string over itself to check both sides. String test for plumb: * An “out of plumb” conditi ...

  • Therma-Tru Pre-hung Door Systems - page 4

    On subfloor at opening, place very large beads of caulk. Run beads full width of opening. Elastomeric or Polyurethane sealant. Use Only Nota: Si se usa unprolongador de umbral, aplique una gran cantidad de masi- lla en la union entre el prolongador de umbral, aplique una gran cantidad de masilla en la union entre el prolongador y el umbral. En el s ...

  • Therma-Tru Pre-hung Door Systems - page 5

    Elastomeric or Polyurethane caulk must be used. Lay door unit on edge or face so that bottom side of sill can be caulked. Place very large beads of caulk across full width of sill. Additionally , place “Elastomeric or Polyurethane caulk” along the junction of the sill and jamb and on the bottom surface of the jambs and brickmold. Apoye la puert ...

  • Therma-Tru Pre-hung Door Systems - page 6

    Use #8 2-1/2” or 3” screws . Place screws through jamb into studs, at each location where shown in diagrams. place screw at each hinge location, so that shims may be placed behind hinges. Screws will keep shims from falling down while adjustments are made. For sidelite units see illustration below for screw placement. Do not drive screws comple ...

  • Therma-Tru Pre-hung Door Systems - page 7

    Shim behind hinges and secur e hinge jamb. Adjust r est of frame and fasten. Ajuste el r esto del mar co y fije. Coloque cazas detras de las bisagras y fije el mar co de puerta. Leave door fastened and closed with transport clip. Shim above screws, behind each hinge, between jamb and opening. Recheck hinge jamb to ensure it is plumb and straight. U ...

  • Therma-Tru Pre-hung Door Systems - page 8

    Unclip and open door . Install hardwar e. Complete jamb fastening. Retir e el sujetador para transporte y abra la puerta. Instale los aditamentos. T ermine de fijar el mar co de puerta. Adjust sill. Ancle el umbral, ajuste el umbral. (Algunos umbrales) Remove transport clip. Open and close door to ensure smooth operation. Remove small margin shims, ...

  • Therma-Tru Pre-hung Door Systems - page 9

    Check or install corner seal pads. (Swing-in doors only) Revise o instale almohadillas sella- doras para las esquinas (solo para puertas que abr en hacia adentr o). Anclaje adicional del mar co. Additional frame anchoring W eather pr oof, finish and maintain Pr oteccion contra intemperie, termi- nado y mantenimiento del sistema de puerta de entraad ...

  • Therma-Tru Pre-hung Door Systems - page 10

    Finishing instructions. Instrucciones para el termindo. W ork only when temperatures are btween 50 º and 90ºF and with humidity less than 85%. Do not finish in direct sunlight. STEEL and SMOOTH-ST AR® Doors: T o Paint Doors: T o paint Doorlite Frames: CL ASSIC -CRAFT® and FIBER-CL A SSIC® Doors: T o Finish Doorlite Frames and P anel Inser ts: ...

Manufacturer Therma-Tru Category Door

Documents that we receive from a manufacturer of a Therma-Tru Pre-hung Door Systems can be divided into several groups. They are, among others:
- Therma-Tru technical drawings
- Pre-hung Door Systems manuals
- Therma-Tru product data sheets
- information booklets
- or energy labels Therma-Tru Pre-hung Door Systems
All of them are important, but the most important information from the point of view of use of the device are in the user manual Therma-Tru Pre-hung Door Systems.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Therma-Tru Pre-hung Door Systems, service manual, brief instructions and user manuals Therma-Tru Pre-hung Door Systems. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Therma-Tru Pre-hung Door Systems.

Similar manuals

A complete manual for the device Therma-Tru Pre-hung Door Systems, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Therma-Tru Pre-hung Door Systems by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Therma-Tru Pre-hung Door Systems.

A complete Therma-Tru manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Therma-Tru Pre-hung Door Systems - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Therma-Tru Pre-hung Door Systems, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Therma-Tru Pre-hung Door Systems, that we can find in the current document
3. Tips how to use the basic functions of the device Therma-Tru Pre-hung Door Systems - which should help us in our first steps of using Therma-Tru Pre-hung Door Systems
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Therma-Tru Pre-hung Door Systems
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Therma-Tru Pre-hung Door Systems in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Therma-Tru Pre-hung Door Systems?

Use the form below

If you did not solve your problem by using a manual Therma-Tru Pre-hung Door Systems, ask a question using the form below. If a user had a similar problem with Therma-Tru Pre-hung Door Systems it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)