English dropdown-ico

Manual Security 100 KE-265

14 pages 0.76 mb
Download

Go to site of 14

Summary
  • Security 100 KE-265 - page 1

    KE-265 Keyless Entry  Access Control System Installation and Operations Manual ...

  • Security 100 KE-265 - page 2

    Table of Contents ESSEX ELECTRONICS, INC. INTRODUCTION ....................................................................................... 2 KE-265 Series O VERVIEW .............................................................................................. 2 All rights reserved. No part of this documentation may be reproduced in any form, wi ...

  • Security 100 KE-265 - page 3

    Introduction Input Requirements The KE-265 accepts 12 to 24 volts AC/DC. An optional battery charging module and rechargeable Gel Cells are available to keep the system operational for up to 24 hours during a power interruption. Syst em current draw (maximum): Overview The KE-265 is an easy to program, easy to use, stand-alone Keyless Entry ® syst ...

  • Security 100 KE-265 - page 4

    Prep aring for Inst allation Keypad Options All Essex Keypads are designed to perform reliably in even the most extreme environmental conditions. Operating temperatures can range from -40 ° C to +70 ° C (-40 ° F to 160 ° F). The KE-265 is compatible with any of the following Keypad styles/configurations : System Components There are four primar ...

  • Security 100 KE-265 - page 5

    The Inst allation Procedure 6. Do NOT mount Keypad at this time. 7. Proceed to Install the Wiring Cable. Required Tools Mounting Instructions 12 Pad 3x4: KP-34S, KP-34B or KP-34K You will need the following tools: The 3x4 keypad is designed to mount to a single gang switchbox or on a wall, pedestal or any flat surface of at least 3 ½ by 5 ¼”. T ...

  • Security 100 KE-265 - page 6

    Install the Wiring Cable 1. Drill a ½” hole in the inside wall or ceiling where you want the cable to come through. 2. Pull the cable through the hole so the connector end goes to the keypad. Route it so there is minimal cable at the keypad.  Note: Supplied with the system is a 12-conductor cable designed to connect the keypad to the control ...

  • Security 100 KE-265 - page 7

    System Hardware Setup The Factory Default Settings are shown here: Remote By-Pass 1. All User Unlock Authorization is configured for Relay #1. (Master Code and Users 1,2 and Users 3,4,5). Factory Default Settings In some cases, it may be necessary to control the door from a remote area such as a security station or reception desk. The KE-265 provid ...

  • Security 100 KE-265 - page 8

    12 Latching Authorization Placing jumpers across the 4 th and 5 th set of pins (1,2 LATCH or 3,4,5 LATCH) determines which relay (if any) each User Group is authorized to manually latch. How to Latch When a valid code is entered on the keypad followed by “7”, the Latch Authorization relay for that particular User Group will energize and remain ...

  • Security 100 KE-265 - page 9

    14 System Programming Overview of System Code Programming There are TWO levels of codes for the KE-265 system. 1. The Master Code (used to open the door and for programming User Codes) 2. User Codes (used by personnel to open the door) IMPORTANT: Notes to remember before programming: 1. All codes must be 3 to 8 digits. 2. All codes must be differen ...

  • Security 100 KE-265 - page 10

    16 Programming User Codes To Program a New User Code or Change an Existing User Code: 1. Choose a new 3 to 8 digit code that will be used for this User Code. ___ ___ ___ ___ ___ ___ ___ ___ 2. Decide which User Location to place this User Code (see Overview of User Codes) 3. Enter the Master Code, followed by the User Location (you will hear three ...

  • Security 100 KE-265 - page 11

    18 T roubleshooting These are a few troubleshooting suggestions to help assist with any problems you may experience. If the problem continues or is not answered here, please call Essex technical support at (800) KEYLESS Î (800) 539-5377. You can also visit Essex anytime at keyless.com or send email to support@keyless.com. I Changed or Deleted a co ...

  • Security 100 KE-265 - page 12

    20 Keypad beeps all by itself Constant Beeping - If the beep is consistently every 5 seconds, put a . 1 uf 16v (or higher) ceramic capacitor across wires 3 & 10 (black, violet) on terminal strip “A”. Random Beeping - Check for bad circuit ground going to the keypad. Is the black wire from the wiring cable securely fastened to screw #3 on Te ...

  • Security 100 KE-265 - page 13

    22 23 Appendix A – Circuit Board Layout Upon receipt of such notification, Esse x Electronics, Incorporated w ill determine whether to repair or replace. We also re serve the right to hav e our representative make any inspection or repairs, or furnish replacements. DISCLAIMER OF WARRANTIES: LIMITATION OF BUYER’S REMEDIES EXCEPT FOR THE REPAIR O ...

  • Security 100 KE-265 - page 14

    Appendix B- T ypical Wiring Diagrams Notes  Note: Some low current strikes or relays w ill cause relay chatter due to inductive kickback. Attach MOV across st rike or relay to eliminate chatter. Master Code ___ ___ ___ ___ ___ ___ ___ ___ Username ________________ 24 Fail Secure Lock Fail Safe Lock Controlled by KE-265 Controlled by KE-265 User ...

Manufacturer Security 100 Category Garage Door Opener

Documents that we receive from a manufacturer of a Security 100 KE-265 can be divided into several groups. They are, among others:
- Security 100 technical drawings
- KE-265 manuals
- Security 100 product data sheets
- information booklets
- or energy labels Security 100 KE-265
All of them are important, but the most important information from the point of view of use of the device are in the user manual Security 100 KE-265.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Security 100 KE-265, service manual, brief instructions and user manuals Security 100 KE-265. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Security 100 KE-265.

Similar manuals

A complete manual for the device Security 100 KE-265, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Security 100 KE-265 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Security 100 KE-265.

A complete Security 100 manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Security 100 KE-265 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Security 100 KE-265, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Security 100 KE-265, that we can find in the current document
3. Tips how to use the basic functions of the device Security 100 KE-265 - which should help us in our first steps of using Security 100 KE-265
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Security 100 KE-265
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Security 100 KE-265 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Security 100 KE-265?

Use the form below

If you did not solve your problem by using a manual Security 100 KE-265, ask a question using the form below. If a user had a similar problem with Security 100 KE-265 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)