English dropdown-ico

Manual MSB Technology DAC II

7 pages 0.67 mb
Download

Go to site of 7

Summary
  • MSB Technology DAC II - page 1

    D A C II Preamp Users Manual Rev 1 (1/03) S IGN M AGNITUDE L ADDER DAC S PECIFICA TIONS I NPUTS :C OAXIAL , T OSLINK , BALANCED AES/EBU, 2 MSB N ETWORK (192K) AND A B ALANCED A NALOG I NPUT RCA O UTPUTS : 3.6V RMS (10Vpp) O UTPUT I MPEDANCE : 50 OHMS AT 0dB B ALANCED O UTPUT : 7.5 V RMS (20Vpp) V OLUME C ONTROL :2 d B STEPPED A TTENUAT OR (32 STEPS ...

  • MSB Technology DAC II - page 2

    D A C II Preamp Users Manual Rev 1 (1/03) Unique Product - a Preamp or a DA C? This product is a unique combination of a very high performance DAC and the ultimate passive preamp. It is intended to be used as both for the best possible sound in your system. Our preamp philosophy is based on the belief that from the moment analog audio is created, e ...

  • MSB Technology DAC II - page 3

    3 Unique Technology - the past and the future Over 10 years ago early DACs were all 16 bit ladder DACs, with a precision laser- trimmed resistor creating the appropriate analog level for each of the bits. The DACs worked well and sounded good. They were quite expensive as very accurate resistors were required. Then along came the “single bit” D ...

  • MSB Technology DAC II - page 4

    4 listen to. Music with less high frequencies may benefit from the slow roll-off filter . T o play a 24/192 disc the source player needs to have an MSB Network output. If your DVD-A player does not have the MSB Network output, it can be added. A 192k input will override the upsampling settings. Front P anel Controls Fr equency and V olume Display ? ...

  • MSB Technology DAC II - page 5

    5 Rear P anel Det ails Inputs Analog (SACD) – A balanced analog input is provided. It is passed through to both the single ended and balanced outputs when selected. (As well as the volume control if installed). This input is ideal for adding an SACD player to your system. Minimum input impedance is 600 ohms. For an RCA input, use an RCA to XLR co ...

  • MSB Technology DAC II - page 6

    6 Remove the cover of the Platinum. W ork on a soft scratch resistant surface like a carpeted floor . Three screws are located al ong the back edge and three screws on the bottom along the front edge. W ith these screws out, the cover lifts off. Now the power supply mu st be separated from the DAC. Each side panel is attached to both the top DAC pa ...

  • MSB Technology DAC II - page 7

    Troubleshooting No “Source” indicated on LEDs - Check for bad cable, or cable plugged into the wrong output on the transport. No sound - Check that source is valid audio source. Change to a standard CD just to be sure. Check that analog outputs are connected p roperly . Check that volume is turned up. Still no sound - connect an analog output f ...

Manufacturer MSB Technology Category Stereo Amplifier

Documents that we receive from a manufacturer of a MSB Technology DAC II can be divided into several groups. They are, among others:
- MSB Technology technical drawings
- DAC II manuals
- MSB Technology product data sheets
- information booklets
- or energy labels MSB Technology DAC II
All of them are important, but the most important information from the point of view of use of the device are in the user manual MSB Technology DAC II.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals MSB Technology DAC II, service manual, brief instructions and user manuals MSB Technology DAC II. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product MSB Technology DAC II.

Similar manuals

A complete manual for the device MSB Technology DAC II, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use MSB Technology DAC II by users. Manuals are usually written by a technical writer, but in a language understandable to all users of MSB Technology DAC II.

A complete MSB Technology manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual MSB Technology DAC II - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the MSB Technology DAC II, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the MSB Technology DAC II, that we can find in the current document
3. Tips how to use the basic functions of the device MSB Technology DAC II - which should help us in our first steps of using MSB Technology DAC II
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with MSB Technology DAC II
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of MSB Technology DAC II in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning MSB Technology DAC II?

Use the form below

If you did not solve your problem by using a manual MSB Technology DAC II, ask a question using the form below. If a user had a similar problem with MSB Technology DAC II it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)