English dropdown-ico

Manual Edelbrock 3527

39 pages 1.2 mb
Download

Go to site of 39

Summary
  • Edelbrock 3527 - page 1

    1 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc T ABLE OF CONTENTS Part #3527 and #3528 Introduction.................................................................................................................................................1 Components............ ...

  • Edelbrock 3527 - page 2

    2 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc PRIMAR Y KIT COMPONENTS ❑ Electronic Control Unit/System ECU ❑ Fuel filter ❑ Calibration Module ❑ Fuel rail assembly ❑ Distributor conversion kit ❑ Fuel pressure regulator ❑ Fuel injectors ❑ High pressure ...

  • Edelbrock 3527 - page 3

    3 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc TOOLS AND EQUIPMENT Use the following checklist for items needed. ❑ Box and open end wrenches ❑ Socket set ❑ Distributor wrench ❑ Pliers (channel locks and hose clamp) ❑ Screwdrivers (regular and Phillips) ❑ T ...

  • Edelbrock 3527 - page 4

    4 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc MANIFOLD & CARBURETOR HEIGHT VS . PRO-FLO XT HEIGHT 1. Lay a straightedge (such as a yardstick) across the top of the air cleaner from front to back. 2 . Measure from block and manifold end seal surfaces to straighted ...

  • Edelbrock 3527 - page 5

    5 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc FUEL REQUIREMENTS Because the Pro-Flo XT system uses an Oxygen sensor, you must use unleaded fuel only. Leaded fuels will damage the O 2 sensor. If you do use leaded fuel in your vehicle, do not install the O 2 sensor and ...

  • Edelbrock 3527 - page 6

    6 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc FUEL SYSTEM Because your Edelbrock Pro-Flo XT system controls fuel delivery very differently than a carburetor, some conversions to your fuel system are necessary. Pro-Flo XT electronic fuel injection requires high and co ...

  • Edelbrock 3527 - page 7

    RUBBER RETURN LINE METHOD Drill a 5/16-inch hole in the sending unit plate adjacent to where the main line enters the tank. This will be the hole for your return line. Insert a short length of 5/16-inch hard line (available at most radiator shops) into the hole and weld it to the sending unit plate. The hard line should extend through the hole 1 to ...

  • Edelbrock 3527 - page 8

    HARD RETURN LINE METHOD Drill a 5/16-inch hole in the sending unit plate adjacent to where the main line, enters the tank. This will be the hole for your return line. Insert a length of 5/16-inch hard line (available at most radiator shops) into the hole and weld it to the sending unit plate. The hard line should extend through the hole 1 to 2 inch ...

  • Edelbrock 3527 - page 9

    9 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc NOTE: ALL WELDING AND SOLDERING OF THE FUEL SYSTEM MUST BE PERFORMED BY A PROFESSIONAL RADIA TOR AND/OR FUEL SYSTEM REP AIR SHOP . FUEL SYSTEM INST ALLA TION 1. Drain the fuel tank. 2. Remove all fuel lines from the tank ...

  • Edelbrock 3527 - page 10

    10 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc INDUCTION SYSTEM The Edelbrock Pro-Flo XT system delivers fuel and air to the engine via the induction system consisting primarily of a manifold, 90mm air valve, fuel rails, and fuel injectors. The induction system is fu ...

  • Edelbrock 3527 - page 11

    11 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc PRE-INST ALLA TION Before installing the induction system, take the following steps to ensure successful installation and performance 1. Check all components thoroughly for damage. 2. Make sure all throttle linkages open ...

  • Edelbrock 3527 - page 12

    12 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc GASKET SURF ACE PREP ARA TION CAUTION: Replace all gaskets as recommended. Do not use race-type non-embossed gaskets for street applications. Due to material deterioration under street driving conditions, internal vacuum ...

  • Edelbrock 3527 - page 13

    13 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc SENSORS The Edelbrock Pro-Flo XT system interprets overall engine operating conditions and fuel/spark requirements based on readings from sensors that measure specific engine conditions. The Pro-Flo system includes five ...

  • Edelbrock 3527 - page 14

    14 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc OXYGEN (O 2 ) SENSOR An oxygen sensor, installed on the header collector pipe, measures exhaust gas oxygen content and is used by the ECU to manage fuel delivery under closed loop control. Installing the sensor requires ...

  • Edelbrock 3527 - page 15

    15 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc O 2 SENSOR INST ALLA TION The exhaust gas oxygen content is determined by the oxygen sensor. The sensor signals the ECU, which compensates when the air/fuel mixture is either rich or lean. NOTE: It is recommended that th ...

  • Edelbrock 3527 - page 16

    16 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc ENGINE HARNESS LA Y OUT ...

  • Edelbrock 3527 - page 17

    17 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc MAIN SYSTEM HARNESS This diagram illustrates the chassis side of the Pro-Flo XT Main System Harness. ...

  • Edelbrock 3527 - page 18

    18 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc ...

  • Edelbrock 3527 - page 19

    19 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc MAIN SYSTEM HARNESS This diagram illustrates the engine side of the Pro-Flo XT Main System Harness. ...

  • Edelbrock 3527 - page 20

    20 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc ...

  • Edelbrock 3527 - page 21

    21 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc INST ALLA TION The Pro-Flo XT Main Harness is divided into two pieces, the engine harness and chassis harness. A bulkhead connector is provided as a pass through firewall connector. 1. Inspect the Main System Harness, ma ...

  • Edelbrock 3527 - page 22

    22 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc ENGINE HARNESS J18: O 2 Sensor J19: Fuel Pump Coil Connectors Ignition Harness J2: Customer Interface O 2 Sensor Select J4: Distributor RT2: +12v Starter Permanent Power J1: Firewall Bulkhead Connector J6: Ignition Coil ...

  • Edelbrock 3527 - page 23

    23 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc The Coolant Temperature sensor attaches to the harness with Connector J15. The Manifold Absolute Pressure sensor attaches to the harness with Connector J17. The Manifold Air Temperature sensor attaches to the harness wit ...

  • Edelbrock 3527 - page 24

    24 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc A. The ignition harness is attached to the main harness with the connector, as shown at left below, and at the coil with the ring terminals on the right below. The ground goes to the rear of the cylinder head. Connect th ...

  • Edelbrock 3527 - page 25

    25 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc IGNITION SYSTEM The photo below shows how the distributor, ignition harness, and Main System Harness are connected. A KEY ON wire (Pink with black stripe) is also included in the Pro-Flo system. This wire connects to a r ...

  • Edelbrock 3527 - page 26

    26 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc ADDING AFTERMARKET IGNITION If you are wishing to use a MSD 6AL or MSD 6-Digital ignition with your Pro-Flo fuel injection, follow the wiring diagram below . NOTE: When installing the MSD box, keep the red battery lead, ...

  • Edelbrock 3527 - page 27

    27 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc CUSTOMER INTERF ACE CONNECTOR A customer interface connector is included in the engine side harness. This connector is optional and also includes a mating cap with wire seals that should be connected at all times to seal ...

  • Edelbrock 3527 - page 28

    28 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc To connect the ECU to your PC, plug the 34 pin ECU connector into the ECU. The connector will only plug in one way. Connect the DB9 serial connector to your PC either directly or through an extension cable (not included) ...

  • Edelbrock 3527 - page 29

    29 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc 29 Pro-Flo EFI Installation Instructions SELECTING THE PROPER CALIBRA TION Application Kit Part No. Calibration No. Intake @ .050” S/B Performer 3527 3561 Stock-220° S/B Performer RPM 3527 3560 220°-Greater S/B Perfo ...

  • Edelbrock 3527 - page 30

    30 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc Priming The Fuel Pump Before the engine is started, the fuel pump must be primed to pressurize the system and purge the fuel line of all air. 1. Turn ignition key to the ON position. You should hear the fuel pump go on. ...

  • Edelbrock 3527 - page 31

    31 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc Timing Adjustment Use a timing light to re-time your engine. 1. Remove spark plug from Number One cylinder. 2. Remove coil wire from distributor and ground it. 3. THIS STEP REQUIRES TWO PEOPLE OR USE OF A REMOTE STARTER ...

  • Edelbrock 3527 - page 32

    32 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc Idle Adjustment This procedure is a general recommendation, intended to help you tune up your Pro-Flo ® system. NOTE: In manual transmission cars, this procedure must be followed with the car in Neutral and with the clu ...

  • Edelbrock 3527 - page 33

    33 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc ELECTRONIC ENGINE MANAGEMENT The Edelbrock Pro-Flo system uses the Speed-Density method of electronic engine management, in which fuel and spark requirements are based on engine speed (RPM) and engine load (manifold pres ...

  • Edelbrock 3527 - page 34

    34 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc PRO-FLO QUICK TUNING GUIDE This guide is based on our simple graph that shows the 24 fuel cells that you can tune in to result in a clean and powerful engine. We recommend when you have your Pro-Flo installed, you have t ...

  • Edelbrock 3527 - page 35

    35 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc OPTIONAL PC TUNING FEA TURE To use the optional PC tuning feature, connect a DB9 serial extension cable to connector J25 of the main harness. Connect the other end to your PC’s serial port as shown. Double click on the ...

  • Edelbrock 3527 - page 36

    36 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc CALIBRA TION MODULE DIAGRAM ...

  • Edelbrock 3527 - page 37

    37 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc P ART NUMBERS Edelbrock Pro-Flo Fuel Injection System ..............................................................................Edelbrock #3527, #3528 ECU power relay/Fuel pump relay ................................. ...

  • Edelbrock 3527 - page 38

    38 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc ( 1) Manifold Absolute Pressure sensor ( 1) Manifold Air T emperature sensor ( 1) Coolant T emperature sensor ( 1) Oxygen (O 2 ) sensor ( 1) High pressure fuel pump ( 1) Fuel filter ( 1) Fuel pressure regulator ( 8) Fuel ...

  • Edelbrock 3527 - page 39

    39 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528 Rev. 8/08 - AJ/mc SERVICE In the event that your Edelbrock Pro-Flo System should need servicing, return the unit pre-paid to the Edelbrock Service and Repair facility at 2700 California Street, Torrance, CA 90503. Do not attempt to disass ...

Manufacturer Edelbrock Category Automobile Parts

Documents that we receive from a manufacturer of a Edelbrock 3527 can be divided into several groups. They are, among others:
- Edelbrock technical drawings
- 3527 manuals
- Edelbrock product data sheets
- information booklets
- or energy labels Edelbrock 3527
All of them are important, but the most important information from the point of view of use of the device are in the user manual Edelbrock 3527.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Edelbrock 3527, service manual, brief instructions and user manuals Edelbrock 3527. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Edelbrock 3527.

Similar manuals

A complete manual for the device Edelbrock 3527, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Edelbrock 3527 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Edelbrock 3527.

A complete Edelbrock manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Edelbrock 3527 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Edelbrock 3527, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Edelbrock 3527, that we can find in the current document
3. Tips how to use the basic functions of the device Edelbrock 3527 - which should help us in our first steps of using Edelbrock 3527
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Edelbrock 3527
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Edelbrock 3527 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Edelbrock 3527?

Use the form below

If you did not solve your problem by using a manual Edelbrock 3527, ask a question using the form below. If a user had a similar problem with Edelbrock 3527 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)