Manual Honeywell TH4210D

16 pages 0.51 mb
Download

Go to site of 16

Summary
  • Honeywell TH4210D - page 1

    Installation Guide TH4210D Programmable Thermostat ...

  • Honeywell TH4210D - page 2

    Product Application This thermostat provides electronic control of 24 V A C heat pump systems with aux- iliar y heat (2 heat/1 cool). Must be installed by a trained, experienced technician • Read these instructions carefully . Failur e to follow these instructions can dam- age the product or cause a hazar dous condition. • Check the ratings in ...

  • Honeywell TH4210D - page 3

    PRO TH4210D Programmable Thermostat 1 Install the thermostat about 5 feet (1.5m) above the floor in an area with good air circulation at average temperatur e. Do not install in locations where the thermostat can be af fected by: • Drafts or dead spots behind doors and in corners • Hot or cold air from ducts • Sunlight or radiant heat from app ...

  • Honeywell TH4210D - page 4

    Installation Guide 2 Pre-installation checklist Package contents Check to make sure y our package includes the f ollowing items: • PR O TH4210D digital thermostat (wallplate attached to back) • Operating manual • W all anchors and mounting screws (2 each) • AA alkaline batteries (2) • Quick ref erence card Required tools & supplies ? ...

  • Honeywell TH4210D - page 5

    PRO TH4210D Programmable Thermostat 3 W allplate installation Remove the w allplate from the ther- mostat as shown at left, then f ollow directions below f or mounting. 1 Pull wires through wire hole. 2 P osition wallplate on wall, level and mark hole positions with pencil. 3 Drill holes at marked positions as shown below , then tap in supplied wal ...

  • Honeywell TH4210D - page 6

    Installation Guide 4 Wiring 1 Loosen screw terminals, insert wires into terminal block, then re- tighten screws. 2 Push e xcess wire back into the wall opening. K eep wires in shaded area as shown at left. 3 Plug the wall opening with non- f lamma ble insulation to pr event drafts from affecting thermostat operation. T erminal Designations E E Emer ...

  • Honeywell TH4210D - page 7

    PRO TH4210D Programmable Thermostat 5 1 Power supply . Provide disconnect means and overload pr otection as required. 2 Optional 24 V AC common connection. 3 Use either O or B terminals for changeover valve. 4 L terminal is powered continuously when thermostat is set to Em Heat. 5 Install field jumper between E and Aux if there is no emergency heat ...

  • Honeywell TH4210D - page 8

    Installation Guide 6 AC Power The thermostat can be powered by 24 V A C power , or by batter ies. T o wire the thermostat for AC po wer , connect the common side of the transf or mer to the “C” terminal as shown at left. Connect common side of transformer to “C” terminal Install batteries in back of thermostat (optional if AC powered). Batt ...

  • Honeywell TH4210D - page 9

    PRO TH4210D Programmable Thermostat 7 6 5 T o begin, pr ess and hold the and buttons until the display changes Function number Press to change settings Press to advance to next function Pr ess and hold to exit and save settings Setting Installer setup Follow the pr ocedure below to configure the thermostat to match the installed heating/cooling sys ...

  • Honeywell TH4210D - page 10

    Installation Guide 8 10 0 T est 10 20 30 70 Heating system Emergency heat Cooling system Thermostat information (for refer ence only) 0 Compressor and fan turn off. 1 Compressor and fan turn on. 2 Auxiliary heat turns on. 0 Heat and fan turn off. 1 Heat and fan turn on. 2 Auxiliary heat turns on. 0 Compressor and fan turn off. 1 Compressor and fan ...

  • Honeywell TH4210D - page 11

    PRO TH4210D Programmable Thermostat 9 Built-in compressor pr otection (Setup Function 15) This featur e helps prevent damage to the compressor . Damage can occur if the compressor is r e- started too soon after shutdown. This feature for ces the compressor to wait f or a few min- utes befor e restarting. During the wait time, the message Cool On or ...

  • Honeywell TH4210D - page 12

    Installation Guide 10 Quick refer ence to controls • Set: Press to set time/day/ schedule • Hold: Press to override programmed temperatur e control. • Run: Press to r esume program schedule System switch • Cool: Thermostat controls only the cooling system. • Heat: Thermostat controls only the heating system. • Off: Heating and cooling s ...

  • Honeywell TH4210D - page 13

    PRO TH4210D Programmable Thermostat 11 In case of difficulty If you hav e dif ficulty with your thermostat, please tr y the sugg estions below . Most problems can be corrected quickl y and easily . Display is blank • Check circuit br eaker and reset if necessary . • Make sure heating & cooling power switches ar e on. • Make sure equipment ...

  • Honeywell TH4210D - page 14

    Installation Guide 12 Accessories Please contact your distributor to order accessories. Cover plate assembly ............................................Part Number 50002883-001 (Used to cover marks left by old thermostats.) Specifications T emperature Ranges • Heat: 40° to 90°F (4.5° to 32°C) • Cool: 50° to 99°F (10° to 37°C) Operating ...

  • Honeywell TH4210D - page 15

    ...

  • Honeywell TH4210D - page 16

    Honeywell International Inc. 1985 Douglas Drive North Golden V alley , MN 55422 http://yourhome.honeywell.com Automation and Control Solutions Printed in U.S.A. on recycled paper containing at least 10% post-consumer paper fibers. ® U.S. Registered T rademark. © 2005 Honeywell International Inc. Patents pending. All rights reserved. 69-1763 • 0 ...

Manufacturer Honeywell Category Thermostat

Documents that we receive from a manufacturer of a Honeywell TH4210D can be divided into several groups. They are, among others:
- Honeywell technical drawings
- TH4210D manuals
- Honeywell product data sheets
- information booklets
- or energy labels Honeywell TH4210D
All of them are important, but the most important information from the point of view of use of the device are in the user manual Honeywell TH4210D.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Honeywell TH4210D, service manual, brief instructions and user manuals Honeywell TH4210D. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Honeywell TH4210D.

Similar manuals

A complete manual for the device Honeywell TH4210D, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Honeywell TH4210D by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Honeywell TH4210D.

A complete Honeywell manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Honeywell TH4210D - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Honeywell TH4210D, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Honeywell TH4210D, that we can find in the current document
3. Tips how to use the basic functions of the device Honeywell TH4210D - which should help us in our first steps of using Honeywell TH4210D
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Honeywell TH4210D
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Honeywell TH4210D in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Honeywell TH4210D?

Use the form below

If you did not solve your problem by using a manual Honeywell TH4210D, ask a question using the form below. If a user had a similar problem with Honeywell TH4210D it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)