Manual Ingersoll-Rand 8476-A1

12 pages 0.82 mb
Download

Go to site of 12

Summary
  • Ingersoll-Rand 8476-A1 - page 1

    OPERATORS MANUAL a- SECTION MANUAL INCLUDING: OPERATION, INSTALLATION & MAINTENANCE “0004” SERIES GRINDERS Released: 10/72 Revised: 3-l0-95 Form: 006-2 Tool Products Models: 8475-A-( ), 8475-A1, 8476-A, 8476-A1, 8477-A, 8477-A1, 8478-A and 8478-A1. READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING THIS EQUIPMENT. FAILURE ...

  • Ingersoll-Rand 8476-A1 - page 2

    FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY. Wear eye protection when operating or performing maintenance on this tool. Turn off air supply and disconnect air supply hose before installing, , removing or adjusting any accessory on this tool, or before performing any maintenance on this tool. Do not carry the tool by the hose. D ...

  • Ingersoll-Rand 8476-A1 - page 3

    ROUTINE LUBRICATION REQUIREMENTS Ml0 32 Lack of or an excessive amount of lubrication will affect the perfor- mance and life of this tool. Use only recommended lubricants at below time intervals: EVERY 8 HOURS OF TOOL OPERATION - Fill lubricator reser- voirof recommended F.R.L. with spindle oil (29665). If an in line or air line lubricator is not u ...

  • Ingersoll-Rand 8476-A1 - page 4

    MODEL IDENTIFICATION The grinder models listed in the model identification table above are furnished with a collet as standard equipment and are intended for use with mounted wheels and shall not be used with other type grinding wheels. Other size collet inserts or other collet assemblies listed on page 10 can be furnished with the above listed mod ...

  • Ingersoll-Rand 8476-A1 - page 5

    DISASSEMBLY AND ASSEMBLY OF TOOLS Ml0 Disconnect air supply from tool or shut off air supply and exhaust (drain) line of compressed air BEFORE performing maintenance or service to tool. Before starting to disassemble or assemble this tool (any part or completely), be sure to read “Inspection, Maintenance and Instal- lation” section. To minimize ...

  • Ingersoll-Rand 8476-A1 - page 6

    TYPICAL CROSS SECTION OF TOOL -VALVE - MOTOR SPINDLE 6 ...

  • Ingersoll-Rand 8476-A1 - page 7

    SPINDLE SECTION Ml 3 COLLET NUT 41751 T r COLLET BODY 43178 -- _- - - COLLET ASSEMBLY 43179-( ) COLLET (SEE TABLE, PAGE 4) ET ASSEMBLY 44123 COLLET ASSEMBLY 44124-8 -INCLUDED WITH NOSE PIECE 33220 ‘!-COLLET 31812-8 COLLET GUARD 43897 DIFFUSER 43893 COLLET 41750-3 SPINDLE 44602 LOCK NUT 31810 NOSE PIECE 31811 COLLET 31812-8 -- - - (INCLUDES BEARIN ...

  • Ingersoll-Rand 8476-A1 - page 8

    SPINDLE SECTION DISASSEMBLY a. Remove driver (43163) from spindle. Tap end of spindle with a soft face hammer to loosen and remove spindle out nose end (44605) and bearing (33237) to housing. of housing. b. Assemble spindle to housing and assemble driver (43163) to spindle. ASSEMBLY a. Assemble felt seal (44606), wave washer (43150), bearing (42516 ...

  • Ingersoll-Rand 8476-A1 - page 9

    VALVE SECTION Ml0 32 0 43160 LEVER FOR NON -EU MODELS 0 45953 LEVER ASS’Y FOR -EU MODELS Cl * LEVER - ROLL PIN Yl78-44 __o__I ROLL PIN Yl78-216 r , BUT HOUSING431761 (BUlTON THROTTLE) ------ROLL PIN Yl78-211 (BUTTON THROTTLE) HOUSING 43161 (LEVER THROlTLE, NON -EU) (LEVER - VALVE 43170 V~UTTON THROTTLE) .TON 43169 SPRING 31125-----@ v REGULATOR 4 ...

  • Ingersoll-Rand 8476-A1 - page 10

    ACCESSORIES OPTIONAL COLLETS COLLET COLLET NUMBER ASSEMBLY NO. SIZE CAPACITY 41750-1 43179-1 1/8" 3/32” - 1/8” 41750-2 43179-2 3/16” 5/32” - 3/1 6” 41750-3 43179-3 1/4” 7/32” - 1/4” 41750-11 43179-11 3mm 41750-12 43179-12 I - ------ I 6mm I SERIES 43179 3-PIECE COLLETS COLLET NUT - 41751 COLLET BODY - 43170 5/16” - 24 THREAD ...

  • Ingersoll-Rand 8476-A1 - page 11

    TROUBLE SHOOTING Ml0 32 LISTED BELOW ARE SOME OF THE MOST COMMON CAUSES FOR THE GRINDER TO MALFUNCTION. MALFUNCTIONS BEYONDTHE SCOPE OF THIS MANUAL SHOULD BE BROUGHT TO THE ATTENTlON OF YOUR ARO REPRESENTATIVE OR RETURN THE TOOL TO THE FACTORY FOR REPAIR. LOW SPEED AND POWER OR GRIND- ER WILL NOT RUN. THROTTLE VALVE HARD TO OPERATE. TOOL WILL NOT S ...

  • Ingersoll-Rand 8476-A1 - page 12

    Part of world wide Ingersoll-Rand PN49999-116 ...

Manufacturer Ingersoll-Rand Category Grinder

Documents that we receive from a manufacturer of a Ingersoll-Rand 8476-A1 can be divided into several groups. They are, among others:
- Ingersoll-Rand technical drawings
- 8476-A1 manuals
- Ingersoll-Rand product data sheets
- information booklets
- or energy labels Ingersoll-Rand 8476-A1
All of them are important, but the most important information from the point of view of use of the device are in the user manual Ingersoll-Rand 8476-A1.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Ingersoll-Rand 8476-A1, service manual, brief instructions and user manuals Ingersoll-Rand 8476-A1. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Ingersoll-Rand 8476-A1.

A complete manual for the device Ingersoll-Rand 8476-A1, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Ingersoll-Rand 8476-A1 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Ingersoll-Rand 8476-A1.

A complete Ingersoll-Rand manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Ingersoll-Rand 8476-A1 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Ingersoll-Rand 8476-A1, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Ingersoll-Rand 8476-A1, that we can find in the current document
3. Tips how to use the basic functions of the device Ingersoll-Rand 8476-A1 - which should help us in our first steps of using Ingersoll-Rand 8476-A1
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Ingersoll-Rand 8476-A1
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Ingersoll-Rand 8476-A1 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Ingersoll-Rand 8476-A1?

Use the form below

If you did not solve your problem by using a manual Ingersoll-Rand 8476-A1, ask a question using the form below. If a user had a similar problem with Ingersoll-Rand 8476-A1 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)