English dropdown-ico

Manual Bunn H10X

20 pages 1.32 mb
Download

Go to site of 20

Summary
  • Bunn H10X - page 1

    OPERA TING & SERVICE MANUAL BUNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 F AX: (217) 529-6644 www .bunn.com H10X WARNING Ve ry Hot Water Use With Care! ! 10889.0000E 02/08 ©1995 Bunn-O-Matic Corporation T o ensure you have the latest revision of the manual or to obtain the illustrated p ...

  • Bunn H10X - page 2

    2 10889 020608 BUNN-O-MA TIC COMMERCIAL PRODUCT W ARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) All equipment other than as specified below: 2 years parts and 1 year labor . 2) Electronic circuit and/or control boards: parts and labor for 3 years. 3) Compressors on refrigeration equipment: 5 years par ...

  • Bunn H10X - page 3

    3 USER NOTICES Carefully read and follow all notices on the equipment and in this manual. They were written for your protec- tion. All notices are to be kept in good condition. Replace any unreadable or damaged labels. 12537.0000 10889 021408 12593.0000 00831.0000 37881.0000 00656.0000 This equipment must be installed to comply with the Internation ...

  • Bunn H10X - page 4

    4 ELECTRICAL REQUIREMENTS CAUTION - The dispenser must be disconnected from the power source until specified in Initial Set-Up. This dispenser requires 2-wire, grounded service rated 208 or 240 volts ac, 40 amp, single phase. (Refer to the dispenser’ s dataplate for exact voltage requirement.) Electrical Hook-Up CAUTION – Improper electrical i ...

  • Bunn H10X - page 5

    5 INITIAL SET -UP CAUTION - The dispenser must be disconnected from the power source throughout the initial set-up, except when specified in the instructions. 1. Connect the dispenser to the power source and turn on the water supply . 2. The “HEA TER” LED will glow for approximately five seconds. During this time, the electronic circuitry wil ...

  • Bunn H10X - page 6

    6 TROUBLESHOOTING A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic T echnical Service Department. • Inspection, testing, and repair of electrical equipment should be performed only by qua ...

  • Bunn H10X - page 7

    7 TROUBLESHOOTING (cont.) PROBLEM Automa tic refil l will not ope rate afte r drawing hot water . Water flows into the tank continu- ou sl y . (D ispe nser disc onne ct ed fr om power source). Water flows into the tank con - tinuously (Dispenser connected to power source). Water is cold. PROBABLE CAUSE 1. No water 2. Water strainer/flow control ...

  • Bunn H10X - page 8

    8 TROUBLESHOOTING (cont.) PROBLEM Water is cold (cont.) Water boils continuously . PROBABLE CAUSE 3. T ank heater 4. T emperature control 5. Dry plug protection 1. T emperature control 2. Lime build-up REMEDY Refer to Ser vice - T ank heater for testing procedures. See page 19. Refer to Ser vice - Electronic con - trols for testing procedures. See ...

  • Bunn H10X - page 9

    9 SERVICE This section provides procedures for testing and replacing various major components used in this dispenser should ser vice become necessary . Refer to T roubleshooting for assistance in determining the cause of any problem. Component Access WARNING - Disconnect the dispenser from the power source before the removal of any panel or the rep ...

  • Bunn H10X - page 10

    10 SERVICE (cont.) Electronic Control Assembly T roubleshooting: Check these items first • Is circuit board popped out of bracket? • Is cir cuit board wet due to misaligned overow tube? • Is water in overow cup activating oat switch? • Is overow cup not making good contact with tank? • Is dispenser being operated with panels ...

  • Bunn H10X - page 11

    11 SERVICE (cont.) Electronic Controls (cont.) Liquid Level Control T est Procedure 1. Disconnect the dispenser from the power source. 2. Check the voltage across terminals 3 & 4 of the electronic control assembly with a voltmeter . Connect the dispenser to the power source. The indication must be 200 to 240 volts ac for 200 to 240 volt models. ...

  • Bunn H10X - page 12

    12 SERVICE (cont.) Electronic Controls (cont.) T emperature Control Flow Charts (cont.) T emperature Control T est Procedure 1. Disconnect the dispenser from the power source. 2. Check the voltage across terminals 3 & 4 of the electronic control circuit board with a voltmeter . Connect the dispenser to the power source. The indication must be 2 ...

  • Bunn H10X - page 13

    13 SERVICE (cont.) Electronic Controls (cont.) 11. Disconnect the dispenser from the power source. If vol tag e was pres en t as des cri bed, retu rn the new tri ac assembly to Bunn-O-Matic for credit. The temperature control of the system is operating properly . If voltage was not present as described, reinstall your existing electronic control as ...

  • Bunn H10X - page 14

    14 T riac Assembly Removal and Replacement NOTE - Each triac installation requires the use of an approved silicone heat sink compound. Bunn-O-Matic recommends the use of Dow Corning 340 compound or equivalent. It can be purchased direct from Bunn- O-Matic (P .N. M2522.1000) 1. Remove the existing triac assembly held in place with a 10-32 hex keps n ...

  • Bunn H10X - page 15

    15 SERVICE (cont.) Limit Thermostat P1993 FIG. 5 LIMIT THERMOST A T T est Procedure: 1. Disconnect the dispenser from the power source. 2. There are two black wires on the limit thermostat terminals. One comes from the terminal block. The other goes directly to the tank heater terminal. Re- move the black wire at the limit thermostat coming from th ...

  • Bunn H10X - page 16

    16 Location: Th e ove rfl ow pr ote ctio n swi tc h is loc at ed with in the sid e of the dispenser inside the copper overflow cup. For testing or removal of the over flow protection switch, access may also be needed by removing the two screws attaching the electronic control assembly to its mounting bracket. T est Procedure: 1. Once voltage is v ...

  • Bunn H10X - page 17

    17 Solenoid Valve Location: The solenoid valve is located within the side of the dispenser on the right side near the bottom. T o test the solenoid valve, access will also be needed to the electronic control assembly . HAZARDOU S VO LT AGE DI S CONNECT FRO M POWER S OU RC E BE FO R E RE MO VI NG ! WAR NI NG P1994 FIG. 9 SOLENOID V AL VE SERVICE (co ...

  • Bunn H10X - page 18

    18 WHI/BLU to Electronic Contol #1 RED to T erminal Block RED to Electronic Control #5 P1779 FIG. 10 SOLENOID V AL VE WIRING 5. Lift out the solenoid valve. 6. Rem ove the two 10- 32 slo tt ed -he ad scr ew s hold ing the solenoid valve to its mounting bracket. 7. Sec urely in sta ll the new sole no id val ve to its mou nt- ing bracket. The directi ...

  • Bunn H10X - page 19

    19 SERVICE (cont.) T ank Heater Location: The tank heater is located in the tank lid. P1993 FIG. 11 T ANK HEA TER T est Procedure: 1. Disconnect the dispenser from the power source. 2. Check the voltage across the terminals of the tank heater with a voltmeter . Connect the dispenser to the power source. The indication must be 200 to 240 volts ac fo ...

  • Bunn H10X - page 20

    20 GRN/YEL BLK RED BLU WHI/VIO BLK TRIAC TA NK HEA TER BLK RED BLU 200-240 VOL TS AC 2 WIRE + GND SINGLE PHASE 10888.0000C 01/07 © 1989 BUNN-O-MA TIC CORPORA TION SOL SCHEMA TIC WIRING DIAGRAM H10XA GRN/YEL REFILL PROBE PNK- 20 ELECTRONIC CONTROL ASSY TA N RED WHI/BLU BLK OVERFLOW PROTECTION SWITCH BLU 6 3 1 5 4 8 7 2 9 TA N HEA TER REFILL WHI/VIO ...

Manufacturer Bunn Category Coffeemaker

Documents that we receive from a manufacturer of a Bunn H10X can be divided into several groups. They are, among others:
- Bunn technical drawings
- H10X manuals
- Bunn product data sheets
- information booklets
- or energy labels Bunn H10X
All of them are important, but the most important information from the point of view of use of the device are in the user manual Bunn H10X.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Bunn H10X, service manual, brief instructions and user manuals Bunn H10X. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Bunn H10X.

Similar manuals

A complete manual for the device Bunn H10X, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Bunn H10X by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Bunn H10X.

A complete Bunn manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Bunn H10X - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Bunn H10X, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Bunn H10X, that we can find in the current document
3. Tips how to use the basic functions of the device Bunn H10X - which should help us in our first steps of using Bunn H10X
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Bunn H10X
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Bunn H10X in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Bunn H10X?

Use the form below

If you did not solve your problem by using a manual Bunn H10X, ask a question using the form below. If a user had a similar problem with Bunn H10X it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)