English dropdown-ico

Manual Autostart AS-2775

34 pages 0.49 mb
Download

Go to site of 34

Summary
  • Autostart AS-2775 - page 1

    Notice The manufactur er will accept no responsibility fo r any electrica l damage resulting from improper in stallation of the product, b e that either damage to the vehicl e itself or to t he unit. This uni t must be installed by a certified tech nician using a ll safety devices s up plied . Please note that this guide has been written for proper ...

  • Autostart AS-2775 - page 2

    P. 2 Installation Guide Table of Contents Introducti on ............................................................ 2 Included in the Kit .................................................. 3 Installati on Tools .................................................... 3 Installation Points to Reme mber .......................... 3 Installatio n Order . ...

  • Autostart AS-2775 - page 3

    Installation Guide P. 3 Included in the Kit Before beginning the installation, pleas e review the Installation Guide —particularly the Wiring Diagram and the Programming Options. Note: It is very important t hat you familiariz e yourself with the pro gramming and o peration of the system, even if you have already inst alled a similar system in t ...

  • Autostart AS-2775 - page 4

    P. 4 Installation Guide ♦ When wiring in parall el, make sure to isolate each c onnection with a diode in order to avoid feed back and pos sible damage. Examples: Wiring a clutch bypass and a transponder module to the ground out when running wire: At the junctio n point, where Ground Out when running “splits” and goes to each dev ice, a diode ...

  • Autostart AS-2775 - page 5

    Installation Guide P. 5 Installation Order The following is a suggested order for the Installation pr ocedure. It is intended as a guide f or novices, to hel p make the pr ocess of insta lling a remote s tarter module eas ier. Time is wasted by rewiring the module whe n mistakes are mad e. Also, the nea tness of t he installation is lessened every ...

  • Autostart AS-2775 - page 6

    P. 6 Installation Guide when the module i s in the vehicl e. The fuses on t he power wires shou ld be removed d uring the pre-wire stage. The fus es will not be put back in unt il the powerin g stage of the i nstallation. − Once the pre-wiring is finis hed, the module c an be brought int o the vehicle. Be fore the module i s mounted, connect the ...

  • Autostart AS-2775 - page 7

    Installation Guide P. 7 A basic introduction to the Relay What is a relay? A device that responds to a small current or v oltage change by activating sw itches or other devices in an electric circ uit. An electroma gnetic switch, remot e-controlled switc h, a switc hing device. Why are Relays used? Relays can have sev eral purposes in remote car st ...

  • Autostart AS-2775 - page 8

    P. 8 Installation Guide quenching/sup pression diode, and t hat the Negative trigg er is on the same terminal of the relay as the Anode (+ or no n-striped side) of the quenchin g/ suppression diode. When a relay’s coil is energiz ed, a magnetic fie ld is created and e nergy is stored in the coil . When power is removed from the coil, the magnetic ...

  • Autostart AS-2775 - page 9

    Installation Guide P. 9 Problem: Some vehicle circuits nee d to be isolate d from feedback . In some cas es, when a vehicl e is remote started , feedback oc curs on a circu it and powers anot her device or sw itch that was not intended to be p owered during t he remote starts. The following example will b e a Positive (+) Parking Light circ uit tha ...

  • Autostart AS-2775 - page 10

    P. 10 Installation Guide the relay is act ivated, +12 vol ts from 87 is sent t hrough 30, and t he OEM trunk sw itch is activated, by the positiv e pulse. Interruption: Example : Creating a St arter Kill relay to prevent unauthoriz ed starting of the vehicle. Problem : The OEM starter circ uit needs to be disabled only when theft is attempted. Solu ...

  • Autostart AS-2775 - page 11

    Installation Guide P. 11 module's Trunk rel ease output activa tes the relay. The ground sign al is sent from 87 through 30 t o the vehicle's Trunk release wire ac tivating the switc h and opening the trunk. Harness Description 6-pin Mai n Ignition Ha rness (a.k.a . The Primary ha rness) The two Red wires are the power i nputs for the mod ...

  • Autostart AS-2775 - page 12

    P. 12 Installation Guide 5-pin Secondary Ha rness (a.k.a. the secondary harn ess) This harness has the remaining wires used in basic remote s tarter inst allations, pos itive parking light output, the safety shut down in puts, and the ground wire for the module. Wire Description 1 BLACK (–) Chassis ground input This wire must be connected to bare ...

  • Autostart AS-2775 - page 13

    Installation Guide P. 13 6 VIOLET (+) Door pin input This input should be used in vehicles that use a posi tive-switching Dome Light circuit. Connect to a Door trigger wire testing +12 V with a Door open. CAUTION! You can only use a negative or a positive c onnection. In other wor ds, only the NEGATIVE DOOR INPUT or the POSITI VE DOOR INPUT wire is ...

  • Autostart AS-2775 - page 14

    P. 14 Installation Guide (Also known as the “wait-to-start light”.) T he purpose of the Glow-plug circuit on diesel vehicles is to pre-heat the Combustion Chamber before the vehicle is started. When a Remote Starter is installed on a dies el vehicle, the Glow - plug section of the Ignition circuit must be activated an d allow ed to operate befo ...

  • Autostart AS-2775 - page 15

    Installation Guide P. 15 compatibility and fun ctionalities) . 5 Pager Port Is used t o connect an optional AS-200P pager (t o use this op tion, make sure to program pager option in Menu 3, Feature 5, Option 4 ). Entering Programming Mode This allows th e installer to p rogram the unit. Once the system is in progra mming mode, th e installer will h ...

  • Autostart AS-2775 - page 16

    P. 16 Installation Guide Manual or Automatic Transmission This module may be ins talled on vehic les with manual or aut omatic transmiss ions. It is origin ally configured for m anual transmis sions . If the vehicle you are working on is automatic, it is mandatory to make a few quic k and easy modi fications before t he unit is conn ected. In the e ...

  • Autostart AS-2775 - page 17

    Installation Guide P. 17 2. Before the lights go out, press and hold the brake p edal and then pre ss one of the foll owing buttons: LOCK ............................... to access menu 1; UNLOCK ........................... to access menu 2; TRUNK …………………… to access menu 3; or START ............................. to access menu 4. 3. ...

  • Autostart AS-2775 - page 18

    P. 18 Installation Guide OPTION 2* Ignition valet ENABLED MENU 3 * INDICATES DE FAULT SETTI NG FEATURE 1 – Home Valet OPTION 1 Home val et ENABLED OPTION 2* Home valet DISABLED FEATURE 2 – AUX 1 Programming OPTION 1 Horn confirmation upon t he 2 nd press of the LOCK button. OPTION 2* Priority door acce ss OPTION 3 Horn confirmation upon t he 1 ...

  • Autostart AS-2775 - page 19

    Installation Guide P. 19 Multi-speed Tach Programming 1. Enter programming mode (see o n page 15)  the park ing lights w ill stay on for up to 20 seconds. 2. Before the lig hts go out, press and hold the brake p edal and press the LOCK and UNLOCK buttons simult aneously  the park ing lights will flas h 4 times. At that p oint, release the b r ...

  • Autostart AS-2775 - page 20

    P. 20 Installation Guide Clutch Bypass In order to rem ote start a manual transm ission vehicl e, the clutch swi tch must be bypasse d. Clutch safety switch c ircuits can take many forms. Lis ted below are th e most comm on ones. Some vehicles may also have a separate or c ombined switch on the cl utch pedal for cruis e control. Usually a cruise c ...

  • Autostart AS-2775 - page 21

    Installation Guid e P. 21 modules connecte d to the G.O. Wire, a relay (and d iodes) may have to be add ed to strengthen t he negative current going to the clutc h bypass. Positive: Very similar to the n egative system, e xcept that the ve hicle's clut ch relay is trigge red by 12 volts instead of a negative signal. In a Positive system, when ...

  • Autostart AS-2775 - page 22

    P. 22 Installation Guide ¾ Standard Secure Lock: If this Option is selected, upo n receiving a remote START signal, secure lock will unlock th e doors (disarming the fa ctory Alarm); 1/2 s econd after the remot e start, it will relo ck t he doors. Four seconds after shut down, secure lock will relock all doors ( arming the system once ag ain). Ple ...

  • Autostart AS-2775 - page 23

    Installation Guid e P. 23 Flashing LED To gain access to this feature, make s ure the Flashing LED option h as been enabled a t the time of programming. Onc e this option is enabled, t he user has the choice to t oggle the Flas hing LED ON and OFF at any giv en moment. To toggle between the Fla shing LED ON and OFF , press LOCK and TRUNK s imultane ...

  • Autostart AS-2775 - page 24

    P. 24 Installation Guide If the vehicle has a manual transmission , Idl e Mode can be ac tivated through the same routine as that used for Ready Mod e (see “Ready Mode Option” in this Guide) ; at the last step, t he TRUNK button is press ed instead of the o ther buttons . Please note that the horn will honk once and that the OEM-style alarm wil ...

  • Autostart AS-2775 - page 25

    Installation Guid e P. 25 If Safe Start is enabled , you can activate Cold W eather Mode by: • Pressing and rele asing the START butto n, then; • Pressing and hol ding the START button u ntil the parkin g lights flash 3 times . To verify whether the system i s in Cold Weather Mode (automati c transmissions only) : • Press the brake p edal: ? ...

  • Autostart AS-2775 - page 26

    P. 26 Installation Guide • To put the system o u t o f Valet mode using the TRANSMITTER (Remote Valet Mode): a. Press the UNLOCK and START butt ons simultane ously until the parking lights flash twice. The LED on the antenna will flash quickly to indicate that the vehicle is now out of Valet mode. • To put the system o u t o f Valet mode using ...

  • Autostart AS-2775 - page 27

    Installation Guid e P. 27 transmitter, and to unlock the other doors , if desired, by pres sing the UNLOCK button for a second time. The output will prov ide a 1-second negative output w hen the UNLOCK button is pres sed a second time on the trans mitter. This c an be used n ot only as priority door access , bu t also as trunk release. ¾ Horn Conf ...

  • Autostart AS-2775 - page 28

    P. 28 Installation Guide To set the syste m to Ready Mode: If Ready Mode is enable d by remote If Ready Mode is enabled by handbrake 1. Ensure that all the doors, hood and trunk are closed. Make sure that the gear selector is in the neutral position. 2. With the engine already running, apply the parking brake once and release the brake pedal. Make ...

  • Autostart AS-2775 - page 29

    Installation Guid e P. 29 5. To save the new settings: pr ess LOCK and UNLOCK . If 3 chirps ar e returned, the new settings have been sav ed Resetting the module to default features Resetting the mo dule is not a required process. Mos t of the time, y ou can avoid res etting the module by fixi ng the issue direc tly at the r oot of the ca use. To r ...

  • Autostart AS-2775 - page 30

    P. 30 Installation Guide  Starter kill option. Sit ins ide the veh icle with all doors closed. Arm th e vehicle, t hen try to start the engine with the key . The engine should not start. If the engine s tarts, rewire the starter kill to reach proper oper ation.  Valet mode. Make sure the re mote car starter is able to proper ly enter and exit ...

  • Autostart AS-2775 - page 31

    Installation Guid e P. 31 Diagnostics – Parking Light Flash Table Flashes Description 1 • Doors locked, starter kill armed. • Run time has expired. • TRUNK button pressed. • Start signal received by the module. • Cold weather mode cancelled. 2 • Doors unlocked, starter kill disarmed. • Remote start atte mpt cancell ed by remote. • ...

  • Autostart AS-2775 - page 32

    P. 32 Installation Guide Troubleshooting Q & A The following ar e some common ins tallation-relate d issues. A problem or symptom is given and then possible solut ions and/or sugge stions as to areas to verify are enumerated. 1. I cannot program the remote control. • Do the parking lights come on when y ou open the hoo d? (Does the hood pin w ...

  • Autostart AS-2775 - page 33

    Installation Guid e P. 33 • Do you have the co rrect OEM disarm wire? • Did you program t he disarm wire? 11. The ABS and the CHECK ENGINE light come on in the dash. • Are you missing a second ignit ion or access ory? 12. The car starts and runs but t he heater blower motor does n ot work. • Incorrect accessory wire . • Does it have more ...

  • Autostart AS-2775 - page 34

    P. 34 Installation Guide 25. I blow fuses ever y time I try the remote door loc ks and I have alr eady installed a r elay. • Door locks are reverse p olarity, and not positive trigger. 26. I blow fuses every time I try the remote trunk rel ease and I have already installed a relay. • Trunk release is rev erse polarity, and not positive trig ger ...

Manufacturer Autostart Category Remote Starter

Documents that we receive from a manufacturer of a Autostart AS-2775 can be divided into several groups. They are, among others:
- Autostart technical drawings
- AS-2775 manuals
- Autostart product data sheets
- information booklets
- or energy labels Autostart AS-2775
All of them are important, but the most important information from the point of view of use of the device are in the user manual Autostart AS-2775.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Autostart AS-2775, service manual, brief instructions and user manuals Autostart AS-2775. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Autostart AS-2775.

Similar manuals

A complete manual for the device Autostart AS-2775, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Autostart AS-2775 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Autostart AS-2775.

A complete Autostart manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Autostart AS-2775 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Autostart AS-2775, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Autostart AS-2775, that we can find in the current document
3. Tips how to use the basic functions of the device Autostart AS-2775 - which should help us in our first steps of using Autostart AS-2775
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Autostart AS-2775
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Autostart AS-2775 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Autostart AS-2775?

Use the form below

If you did not solve your problem by using a manual Autostart AS-2775, ask a question using the form below. If a user had a similar problem with Autostart AS-2775 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)