English dropdown-ico

Manual Siemens CGZ

34 pages 1.17 mb
Download

Go to site of 34

Summary
  • Siemens CGZ - page 1

    ANIM-03522-0402 (New Issue) ©2002 Siemens Energy & Automation, Inc. All rights reser ved. Installation Operation Maintenance Horizontal – Medallion  500, 580, 708, 788, 880 Frames TEFC & Explosion-Proof Enclosures Type CZ, NCZ, CGZ, CGZZ Induction Motors/ Generators ...

  • Siemens CGZ - page 2

    - 1 - Table of Contents Page Page TABLE OF CONTENTS 1 OPERATION 10 SAFETY PROCEDURES 2 Initial Start 10 INTRODUCTION 3 Oil Circulating Systems 10 Warranty 3 Normal Operation 10 Receiving 3 Voltage/Frequency Variation 10 Handling 4 Trouble Shooting 11 Temporary Storage 4 MAINTENANC E 13 Type Designations 4 Preventive Maintenance 13 INSTALLATION 5 In ...

  • Siemens CGZ - page 3

    - 2 - Safety Procedures This equipment contains haza rdous voltages. Death, serious personal inju ry or property damage can resu lt if safety instructions are not followed. The successful and safe ope ration of motors and generators is depend ent upon proper handling, installation, operation and mainte nance, as well as upon proper design and manuf ...

  • Siemens CGZ - page 4

    - 3 - Introduction DANGER Hazardous voltage. Will cause death, serious injur y, electrocution or propert y damage. Disconnect all power before workin g on this equipment. These instructions present general recommendations for installation, operation and mai ntenance of induction motors built at the Norwo od plant. If additional information i s requ ...

  • Siemens CGZ - page 5

    - 4 - Introduction WARNING Heavy equipment. Improper handling may cause death, serious injury or property damage. Check lifting devices before lifting. Use proper slings, chains and spreaders. Note any warning plates on motor and foll ow instructions on each plate. Handling Lifting devices are provided for handling only. An experienced rigger shoul ...

  • Siemens CGZ - page 6

    - 5 - Installation Motor Dimensions For motors built in the frame size s covered by this manual, the letter dim ensions have the same definitions as established NEMA standards. Established dimensions for these frames may be found on catalog sheets or certified dra wings. CAUTION Damp Location. Can cause propert y damage if equipment is oper ated in ...

  • Siemens CGZ - page 7

    - 6 - Installation External Wiring DANGER Hazardous voltage. Will cause death, serious injur y, electrocution or propert y damage. Disconnect all power before workin g on this equipment. NOTE Before runnin g motor, see Initial Start. Starting and overload control devi ces must be matched to motor rating. For safety or convenience they may need to b ...

  • Siemens CGZ - page 8

    - 7 - Installation Angular Alignment Hold each shaft at maximu m end float. Rotate both shafts together, and measure b etween matching points at the outside diameter of the coupli ng faces for the top, bottom and both sides. Use two indicat ors because of possible axial shaft movement. Read difference of variation between them. Align shafts so that ...

  • Siemens CGZ - page 9

    - 8 - Installation Check for vertical alignm ent (parallelism) of coupl ed drive as follows: 1. Operate unit until normal temperature is reached (may require several hours). 2. Shut down motor and lock out switch. 3. Mount dial indicator as in Figure 2. 4. Rotate shaft, noting re adings at 0°, 90°, 180°, and 270° (both sides, top, and bottom). ...

  • Siemens CGZ - page 10

    - 9 - Installation Typical Motor Control Settings Alarm Trip (Shutdown) Timer Trip Setting (1) Winding Temperature • Class B Insulation • Class F Insulation 130°C 155°C 155°C 170°C Motor Bearing Temperature (Thermocouple or RTD’s) • Sleeve Bearing 90°C 95°C • Antifriction Bearing 100°C 105°C Ground Fault 4 Amps (2) Primary Circuit ...

  • Siemens CGZ - page 11

    - 10 - Operation Initial Start CAUTION Do not exceed nu mber of Siemens specified h ot and cold starts per hour. Will cause overheating. Allow time between starts to permit stator windings and rotor cage to cool. After installation is completed, but before motor is pu t in regular service, make an initial start as follows: 1. Check that motor, star ...

  • Siemens CGZ - page 12

    - 11 - Operation Trouble Shooting Between regular maintenance inspe ctions, be alert for signs of motor trouble. Comm on symptoms are listed in the following table. Correct any trouble immediately an d AVOID COSTLY REPAIR AND SHUT DOWN. TROUBLE POSSIBLE CAUSES CORRECTION Usually line trouble. Singl e phasing at starter. Check power source. DO NOT c ...

  • Siemens CGZ - page 13

    - 12 - Operation Trouble Shooting TROUBLE POSSIBLE CAUSES CORRECTION Open stator windings. Disconnect motor from load. Check idle amps for balance in all three phases. Check stator resistance in all three phases for bala nce. Air Recirculation. Check air intake and exhaust for obstructions. Check air inlet temperature. Over voltage/under voltage. C ...

  • Siemens CGZ - page 14

    - 13 - Maintenance Preventive Maintenance Motors are designed to give many years of reliable service with a minimum of attention. Trouble-free operation cannot be expected if p roper maintenance is postponed or neglecte d. Provide proper maintenance on the equipment . Follow carefully the instructions co ntained herein. Be certain personnel review ...

  • Siemens CGZ - page 15

    - 14 - Maintenance WARNING Explosion or fire. Can cause death, serious injur y or property damage. Do not modify explosion-proof or dust ignition-proof motors. These motors are constructed to comply with the U.L. Label Service Procedure Man ual. When reassembling a motor that has a U.L. Label, it is imperative that: 1. The original fits and toleran ...

  • Siemens CGZ - page 16

    - 15 - Maintenance Temperature Electrical apparatus operatin g under normal conditions becomes quit e warm. Although som e places may feel hot to the tou ch, the unit may be within limits. If checking total temperature by winding resistance or imbedded detector (RTD), the total temperature should not exceed the follo wing: When operating at full lo ...

  • Siemens CGZ - page 17

    - 16 - Maintenance Rotor Cleaning Remove rotor. Inspect and clean. Stator Cleaning MICLAD™ for m wound VPI (vacuum pr essure impregnated) insulated coils may be cleaned with a quick drying solvent and lint free cloths or steam cleaned with low-pressure ste am, then the entire stator oven baked at 200° F for 12 hours and then 230°F for 12 hours. ...

  • Siemens CGZ - page 18

    - 17 - Maintenance Electric Strip Heater Drying 1. Remove bearing housing s. 2. Remove rotor. 3. Direct a fan on stator to carry away the moisture. 4. Attach temperature i ndicators to winding and apply heat as specified in the Insulation Drying Temperature table and follo w procedures described for drying insulation. 5. Radiant type heaters are no ...

  • Siemens CGZ - page 19

    - 18 - Maintenance Insulated Bearings One or both bearings m ay be insulated to preven t shaft currents from pitting bearing surfaces. The insulation is located at the joint between the bearing housing or bracket a nd the bearing. Insulated bearings are designated by an instruction plate on the bearing housing. Check periodically to be sure the ins ...

  • Siemens CGZ - page 20

    - 19 - Maintenance At the first sign of oil discoloration or contamination, replace with new oil. Rapi d discoloration is caused by bearing wear, often from vibration or thrust. Chang e oil as required to keep clean. When assembling the bea ring, it is possible to foul the rings so that they will not turn freely. Check ring operation by rotating sh ...

  • Siemens CGZ - page 21

    - 20 - Maintenance Sealing Parts Even though joints may seem to match perfectly, minute clearances exist through which oil may leak. Sealant should be ap plied to the mating surfaces of parts where oil is present to prevent seepage of oil. Sealant should be applied as follows: 1. Surfaces sha ll be clean of dirt, grease, and oil sealant. Use a non- ...

  • Siemens CGZ - page 22

    - 21 - Maintenance Sleeve Bearings CAUTION Maintain proper oil lev el. Failure to do so may cause improper lubric ation of motor resulting in damage to the equipm ent. Follow lubrication instructions carefully. Avoid adding oil while unit is running. Motors with sleeve bearings are shipped without oil. A rust-inhibiting film is applied at the facto ...

  • Siemens CGZ - page 23

    - 22 - Maintenance To Replace Antifriction Bearings 1. Remove bolts holding end caps to housi ngs. 2. Remove bolts holding bearing housin gs to yoke. 3. Remove bearing housing s. 4. Remove the bearing with a puller. See Figure 5. 5. Check shaft and housing diameter for prop er size with micrometer. 6. Heat the new bearing in an oven (200°F). While ...

  • Siemens CGZ - page 24

    - 23 - Maintenance Sleeve Bearing When replacing sleeve b earings, it is always desi rable to check the fit (contact pattern) of the bearing to the shaft. When ordering sleeve bearings, be sure to provide complete motor nameplate an d bearing data. Whenever a bearing is replaced, clea nliness must be observed through every st ep of the operation. A ...

  • Siemens CGZ - page 25

    - 24 - 708, 788, and 880 Frames (See Figure 8) 1. Check repla cement bearings fo r nicks or shipping damage. Do not scrape. 2. Carefully remove the bearing housing cap by fi rst lifting straight up, then pulling away from the bearing area. 3. Remove top half of bearing liner. 4. Remove the bolts at the split line of the oil ring. 5. Remove bearing ...

  • Siemens CGZ - page 26

    - 25 - Identification All units have an identification nam eplate affixed to the frame (Figure 9). All the necessary information pertaining to the motor can be found on this plate including; 1. Serial Number 2. Type and Frame Size 3. Horsepower and Speed 4. Bearing Designations It is important when ordering spa re parts or discussing service to hav ...

  • Siemens CGZ - page 27

    - 26 - Figure 10. Type CZ, 509 & 5011 Frames Item Description Item Description Item Description 1 Stator Core 7 Ball Bearing 14 Inboard Seal 2 Stator Yoke 8 Shaft Seal 15 Oil Seal 3 Stator Coils 10 Grid Cover 16 Bearing Capsule 4 Bearing Housing 11 Rotor Core 17 Sleeve Bearing Bushi ng 5 Rotor Shaft 12 External Fan (4 pole & slower) 18 Shim ...

  • Siemens CGZ - page 28

    - 27 - Spare Parts Item Description Item De scription 1 Stator Core 8 Shaft Seal 2 Stator Yoke 10 Grid Cover 3 Stator Coils 11 Rotor Core 4 Bearing Housing 12 External Fan (4 Pole or Slower) 5 Rotor Shaft 13 Fan Housing 6 Inner End Cap 14 Internal Fan 7 Ball Bearing 15 Rotor Air Du ct Figure 14. Type CGZ, 588 & 5810 Frames Item Description 16 F ...

  • Siemens CGZ - page 29

    - 28 - Spare Parts Figure 15 . Sleeve Bearing Arrangement for Type CGZ 708, 788, & 880 Frames Item Description 18 Oil Seal 19 Bearing Cap. Housing 20 Sleeve Bearing Bushing 21 Shims 22 Machine Seal 23 Oil Ring Item Description Item Description 1 Stator Core 8 Shaft seal 2 Stator Yoke 10 Grid Cover 3 Stator Coils 11 Rotor Core 4 Bearing Housing ...

  • Siemens CGZ - page 30

    - 29 - Motor Service Record Serial No ______________________ Horsepower ______________ Type ___________ Speed ________ Volts _____________ Amperes _____________ Hertz _______ Insulation Class _______ Temperature Rise _______ ° C Frame Size ____________ Owner Order No _________________ Item No _____ Date Of Manufacture _________ MACHINE TYPE BEARIN ...

  • Siemens CGZ - page 31

    - 30 - Vibration Analysis Sheet Pick-Up Filter-Out Coupled Filter-In Couple d Disp. Freq* Vel. Freq.* Vel. Freq . Vel. Freq. Vel. Freq. Vel. Freq. Point Position Mils CPM In/Sec CPM Mils CPM Mils CPM Mils CPM Mils CPM Horizontal Vertical Axi al Horizontal Vertical Axi al Horizontal Vertical Axi al Horizontal Vertical Axi al Horizontal Vertical Axi ...

  • Siemens CGZ - page 32

    - 31 - Notes ___________________ ______________ ___________________ __________________ _______________ _____ ___________________ ______________ ___________________ __________________ _______________ _____ ___________________ ______________ ___________________ __________________ _______________ _____ ___________________ ______________ ______________ ...

  • Siemens CGZ - page 33

    - 32 - Notes ___________________ ______________ ___________________ __________________ _______________ _____ ___________________ ______________ ___________________ __________________ _______________ _____ ___________________ ______________ ___________________ __________________ _______________ _____ ___________________ ______________ ______________ ...

  • Siemens CGZ - page 34

    ANIM-03522-0402 (New Issue) ©2002 Siemens Energy & Automation, Inc. All rights reser ved. Siemens Energy & Automation Industrial Products Divisi on Norwood Motor Plant 4620 Forest Avenue Norwood, OH 45212-3396 (513) 841-31 00 ...

Manufacturer Siemens Category Portable Generator

Documents that we receive from a manufacturer of a Siemens CGZ can be divided into several groups. They are, among others:
- Siemens technical drawings
- CGZ manuals
- Siemens product data sheets
- information booklets
- or energy labels Siemens CGZ
All of them are important, but the most important information from the point of view of use of the device are in the user manual Siemens CGZ.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Siemens CGZ, service manual, brief instructions and user manuals Siemens CGZ. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Siemens CGZ.

Similar manuals

A complete manual for the device Siemens CGZ, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Siemens CGZ by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Siemens CGZ.

A complete Siemens manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Siemens CGZ - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Siemens CGZ, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Siemens CGZ, that we can find in the current document
3. Tips how to use the basic functions of the device Siemens CGZ - which should help us in our first steps of using Siemens CGZ
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Siemens CGZ
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Siemens CGZ in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Siemens CGZ?

Use the form below

If you did not solve your problem by using a manual Siemens CGZ, ask a question using the form below. If a user had a similar problem with Siemens CGZ it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)