English dropdown-ico

Manual Technicolor - Thomson ST536

792 pages 5.19 mb
Download

Go to site of 792

Summary
  • Technicolor - Thomson ST536 - page 1

    Power DSL Ethernet Internet Thomson ST516/536/546 CLI Reference Guide ...

  • Technicolor - Thomson ST536 - page 2

    ...

  • Technicolor - Thomson ST536 - page 3

    Thomson ST516/536/546 CLI Reference Guide R6.2 ...

  • Technicolor - Thomson ST536 - page 4

    Copyright Copyright ©1999-2007 THOMSON. All rights reserved. Distribution and co pying of this do cument, use and communication o f its contents is not permitted witho ut written authorizatio n from THOMSON. The con tent of this docume nt is furnished for informati onal use only , may be subject to ch ange without notice, and should not be con str ...

  • Technicolor - Thomson ST536 - page 5

    E-DOC-CTC-20061 027-0003 v2.0 Contents i About this CLI Reference Guide ....................... ......................... 1 1 Root Commands ........................ .................................................. 3 ping .......... ................ .............. .............. ................. .............. .............. ................. ... ...

  • Technicolor - Thomson ST536 - page 6

    E-DOC-CTC-2006 1027-0003 v2.0 Contents ii atm debug aal5s tats ........... ................ .............. .............. ................. .............. .............. ........ ............... .. 41 atm debug gstats .... ................. .............. .............. ................. .............. .............. ................. ... ......... ...

  • Technicolor - Thomson ST536 - page 7

    E-DOC-CTC-20061 027-0003 v2.0 Contents iii 6 Connection Commands....... .............................. ........................ 81 connection app config ................. .............. ................. .............. .............. ................. .............. ........ ........ 82 connection app info ............... .............. ........... ...

  • Technicolor - Thomson ST536 - page 8

    E-DOC-CTC-2006 1027-0003 v2.0 Contents iv dhcp client debu g traceconfig ............................ ................. ................. ................. ................. .. ...... ... 121 dhcp client rqoptio ns add .......... ................. .............. .............. ................. .............. .............. .. ............ 122 dhcp ...

  • Technicolor - Thomson ST536 - page 9

    E-DOC-CTC-20061 027-0003 v2.0 Contents v dhcp server option instdelete ..................... ................. ................ ................. .................... ....... .......... 163 dhcp server option instlist ....................... ................. ................. ................... ................. ....... .. ........... 164 dhcp se ...

  • Technicolor - Thomson ST536 - page 10

    E-DOC-CTC-2006 1027-0003 v2.0 Contents vi dns server route delete .................... ................ .................... ................. ................. .............. .............. 205 dns server route flush ............. .............. .............. ................. .............. .............. ................. .. ............... 206 ...

  • Technicolor - Thomson ST536 - page 11

    E-DOC-CTC-20061 027-0003 v2.0 Contents vii env set ............. ................. .............. .............. ................. .............. .............. ................ . ......................... 247 env unset ............ .............. ................. .............. .............. ................ .............. .............. ... ... ...

  • Technicolor - Thomson ST536 - page 12

    E-DOC-CTC-2006 1027-0003 v2.0 Contents viii eth bridge maclist ......... ................. .............. .............. .............. ................. .............. .......... ......... ......... 289 eth bridge mcdadd ............. .............. ................ .............. .............. ................. .............. ........ .......... ...

  • Technicolor - Thomson ST536 - page 13

    E-DOC-CTC-20061 027-0003 v2.0 Contents ix 15 Expr Commands .................. .............................. ...................... 327 expr add .... .............. .............. ................. .............. .............. ................. .............. ........... ................. ...... 328 expr delete ................. .............. ... ...

  • Technicolor - Thomson ST536 - page 14

    E-DOC-CTC-2006 1027-0003 v2.0 Contents x grp rip flush................... .............. ................. .............. .............. .............. ................. ..... ....................... 382 grp rip ifcon fig ...................... ................. .............. .............. ................. .............. ............. .......... ...

  • Technicolor - Thomson ST536 - page 15

    E-DOC-CTC-20061 027-0003 v2.0 Contents xi igmp proxy ifl ist .................. ................ .............. .............. ................. .............. .............. ... .................... 422 igmp proxy mb slist ......... ................. .............. .............. .............. ................ .............. ........... ......... ...

  • Technicolor - Thomson ST536 - page 16

    E-DOC-CTC-2006 1027-0003 v2.0 Contents xii ip auto ifdetach ............. .............. .............. ................. .............. .............. ................. ........ .............. ...... 465 ip auto ifli st ........... .............. .............. .............. ................ .............. .............. ................ ........ ...

  • Technicolor - Thomson ST536 - page 17

    E-DOC-CTC-20061 027-0003 v2.0 Contents xiii language co nfig ......... ................. .............. .............. .............. ................. .............. ............. ....... ........... 514 language delete .................... .............. .............. ................. .............. .............. .............. ..... ......... ...

  • Technicolor - Thomson ST536 - page 18

    E-DOC-CTC-2006 1027-0003 v2.0 Contents xiv mlp privilege co nfig ........... .............. .............. ................ .............. .............. ................. ....... ................ 552 mlp privilege d elete ................. ................. .............. .............. ................. .............. .............. ........... . ...

  • Technicolor - Thomson ST536 - page 19

    E-DOC-CTC-20061 027-0003 v2.0 Contents xv ppp relay ifdel ete .................. .............. .............. ................. .............. .............. ................. . ................... 607 ppp relay ifli st ..................... ................ .............. .............. .............. ................. .............. . .......... ...

  • Technicolor - Thomson ST536 - page 20

    E-DOC-CTC-2006 1027-0003 v2.0 Contents xvi service system modify .......................... ................. ................. ................. ................... .......... ............. 647 34 SNMP Commands ............... .............................. ...................... 649 snmp config ..................... ................. ............ ...

  • Technicolor - Thomson ST536 - page 21

    E-DOC-CTC-20061 027-0003 v2.0 Contents xvii system ra config .............. .............. .............. ................. .............. .............. ................ ........ ............... ... 687 system rtc synchronize ................. ................... ................. ................. ................. ................. . ....... ... ...

  • Technicolor - Thomson ST536 - page 22

    E-DOC-CTC-2006 1027-0003 v2.0 Contents xviii user flush ......... .............. ................. .............. .............. ................. .............. .............. .... .................. ...... 727 user list ............... ................. .............. .............. ................ .............. .............. .............. .. ...

  • Technicolor - Thomson ST536 - page 23

    E-DOC-CTC-20061 027-0003 v2.0 About this CLI Reference Guide 1 About this CLI Reference Guide Used Symbols T erminology Generally , the Thomson ST 516/536/546 will be referred to as Thom son ST in this CLI Reference Guide. T ypographical Conventions Following typo graphical convention is us ed throughout this manual: > Sample text indicates a hy ...

  • Technicolor - Thomson ST536 - page 24

    E-DOC-CTC-2006 1027-0003 v2.0 About this CLI Reference Guide 2 ...

  • Technicolor - Thomson ST536 - page 25

    E-DOC-CTC-20061 027-0003 v2.0 Root Commands 3 1 Root Commands From the root pr ompt, you can choose one of the foll owing commands: EXAMPLE: Comma nd Description help Displays the help information. ? menu Displays the menu. exit Exits the shell. .. Exits group selection . saveall Saves current configuration. ping Send ICMP ECHO_REQUE ST packets. tr ...

  • Technicolor - Thomson ST536 - page 26

    E-DOC-CTC- 20061027-0003 v2 .0 Root Commands 4 ping Send ICMP ECHO_REQUES T packets. SYNT AX: where: EXAMPLE: ping proto = <{ip|atm}> addr = <ip-address> dest = <string> [count = <number{0-1000000}>] [size = <number{28-20028}>] [interval(ms) = <number{100-1000000}>] [DF-bit = <{disabled|enabled}>] [srcaddr ...

  • Technicolor - Thomson ST536 - page 27

    E-DOC-CTC-20061 027-0003 v2.0 Root Commands 5 traceroute Send ICMP/UDP packets to trace the IP path. SYNT AX: where: traceroute addr = <ip-address> [count = <number{1-10}>] [size = <number{1-20000}>] [interval = <number{1000-60000}>] [maxhops = <number{1-255}>] [dstport = <number{1-65535}>] [maxfail = <number{ ...

  • Technicolor - Thomson ST536 - page 28

    E-DOC-CTC- 20061027-0003 v2 .0 Root Commands 6 EXAMPLE: =>traceroute addr = 192.193.195.250 count=3 size=1 interval=1000 maxhops=30 dstport=33433 maxfail=5 type=icmp utime=yes :traceroute addr=192.193.195.250 ttl=1 192.193.195.250 676 us 1351 us 648 us => ...

  • Technicolor - Thomson ST536 - page 29

    E-DOC-CTC-20061 027-0003 v2.0 ADSL Commands 7 2 ADSL Commands Introduction This chapter describes the commands of the adsl command group. Contents This chapter covers th e following commands: adsl config Show/set the Asymmetric Digital Sub scriber Line (ADSL) configuration . 8 adsl info Display the ADSL statistics and in formation about the DSL lin ...

  • Technicolor - Thomson ST536 - page 30

    E-DOC-CTC- 20061027-0003 v2 .0 ADSL Commands 8 adsl config Show/set the Asymmetric Digital Su bscriber Line (ADSL) configuration. SYNT AX: where: EXAMPLE: The example belo w shows the default configuration for a T homson ST ADSL/POTS variant: adsl config [opermode = <{multimode | multi_adsl2 | multi_readsl2 | multi_adsl2plus}>] [trace = <{ ...

  • Technicolor - Thomson ST536 - page 31

    E-DOC-CTC-20061 027-0003 v2.0 ADSL Commands 9 adsl info Display the ADSL statistics and inform ation about the DSL line st atus. Although the same comma nd is used for both Thomson ST ADSL/POTS and Thomson ST ADSL/ISDN variants, the command features specific ou tput parameters and counters per variant. SYNT AX: adsl info ...

  • Technicolor - Thomson ST536 - page 32

    E-DOC-CTC- 20061027-0003 v2 .0 ADSL Commands 10 EXAMPLE (for a Thomson ST ADSL/POTS variant): =>adsl info Modemstate : up Operation Mode : G.992.1 Annex A Channel Mode : interleaved Number of resets : 1 Vendor Local Remote Country : 0f 00 Vendor : TMMB VendorSpecific : 0000 0000 StandardRevisionNr : 00 00 Downstream Upstream Margin [dB] : 26.0 1 ...

  • Technicolor - Thomson ST536 - page 33

    E-DOC-CTC-20061 027-0003 v2.0 ADSL Commands 11 adsl debug bitloadinginfo Displays the number of bi ts per tone. Syntax adsl debug bitloadinginfo ...

  • Technicolor - Thomson ST536 - page 34

    E-DOC-CTC- 20061027-0003 v2 .0 ADSL Commands 12 adsl debug deltconfig Enable/disable the Du al Ended Line T es ting Interface (DEL T) Syntax where: adsl debug deltconfig [state = <{disabled|enabled}>] state enable or disable DEL T REQUIRED ...

  • Technicolor - Thomson ST536 - page 35

    E-DOC-CTC-20061 027-0003 v2.0 ADSL Commands 13 adsl debug deltinfo Display Dual En ded Line T est ing Interface (DEL T) results Syntax adsl debug deltinfo ...

  • Technicolor - Thomson ST536 - page 36

    E-DOC-CTC- 20061027-0003 v2 .0 ADSL Commands 14 adsl debug modemoptioninfo Displays the modem op tions bitmap Syntax adsl debug modemoptioninfo ...

  • Technicolor - Thomson ST536 - page 37

    E-DOC-CTC-20061 027-0003 v2.0 ADSL Commands 15 adsl debug modemoption Configure the modem options bitmap Syntax where: adsl debug modemoption [config = <hexbitmap>] config The modem options bitmap REQUIRED ...

  • Technicolor - Thomson ST536 - page 38

    E-DOC-CTC- 20061027-0003 v2 .0 ADSL Commands 16 adsl debug traceconfig Configure the ADSL tracelevel. Syntax where: adsl debug traceconfig [level = <number{0-2}>] level T race Level : > 0=disable traci ng; > 1=enable dsl ma nager tracing; > 2=enable dsl driver tracing) REQUIRED ...

  • Technicolor - Thomson ST536 - page 39

    E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 17 3 A TM Commands Introduction This chapter describes the commands of the atm comman d group. Contents This chapter covers th e following commands: atm flush Flush all Asynchrono us T ransfer Mode (A TM) interfaces. 19 atm ifadd Create a new A TM interface. 20 atm ifattach Attach a A TM inter face. 21 atm ...

  • Technicolor - Thomson ST536 - page 40

    E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 18 atm oam vclb add Create a loopback connection for VC. 52 atm oam vclb del Delete a loopback connection for VC. 53 atm oam vclb list List all VC loopb ack connections. 54 atm phonebook add Add a new phoneboo k entry . 55 atm phonebook autolist Show the auto PVCs. 56 atm phonebook del ete Delete an exist ...

  • Technicolor - Thomson ST536 - page 41

    E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 19 atm flush Flush all Asynchro nous T ransfer Mode ( A TM) interfaces. SYNT AX: atm flush ...

  • Technicolor - Thomson ST536 - page 42

    E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 20 atm ifadd Create a new A TM interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm ifadd intf = <string> intf The name for th e new A TM interface. Note If not specified, the destination para meter must be specified. In this case the name of the destinatio n will double as interface name. REQ ...

  • Technicolor - Thomson ST536 - page 43

    E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 21 atm ifattach Attach a A TM interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm ifattach intf = <string> intf The name of the A TM interf ace to be attached. REQUIRED =>atm iflist atm_0_35 : dest : atm_pvc_0_35 Retry : 10 QoS : default Encaps : vcmux Fcs : off Ulp : mac Connection State : ...

  • Technicolor - Thomson ST536 - page 44

    E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 22 atm ifconfig Configure an A TM interface. SYNT AX: where: i The interface to be configured must not be connected at the tim e of configuration. If this should be the case, use the command :atm ifdetach before using the command :atm ifconfig . atm ifconfig intf = <string> [dest = <string>] [ ...

  • Technicolor - Thomson ST536 - page 45

    E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 23 EXAMPLE: ulp Select the Upper Layer Protoc ol (ULP) for this interface. Choose between: > ip (for a Routed IPoA interface). > mac (for a Bridged Ethernet, Rout ed ETHoA, Bridged PPP ov er Ethernet (PPPoE), Ro uted PPPoE or a PPPoE Relay i nterface). > ppp (for a Routed PPP over A TM (PPPoA) int ...

  • Technicolor - Thomson ST536 - page 46

    E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 24 atm ifdelete Delete an A TM interface . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm ifdelete intf = <string> intf The name of the A TM interface to be deleted. REQUIRED =>atm iflist atm_0_35 : dest : atm_pvc_0_35 Retry : 10 QoS : default Encaps : vcmux Fcs : off Ulp : mac Connection State ...

  • Technicolor - Thomson ST536 - page 47

    E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 25 atm ifdetach Detach an A TM interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm ifdetach intf = <string> intf The name of the A TM interf ace to be detached. REQUIRED =>atm iflist atm_0_35 : dest : atm_pvc_0_35 Retry : 10 QoS : default Encaps : vcmux Fcs : off Ulp : mac Connection State ...

  • Technicolor - Thomson ST536 - page 48

    E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 26 atm iflist Display the A TM interfaces. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm iflist [intf = <string>] intf The name of the A TM interface to be shown. Note If not specified, al l the A TM interfaces are show n. OPTIONAL =>atm iflist atm_0_35 : dest : atm_pvc_0_35 Retry : 10 QoS : de ...

  • Technicolor - Thomson ST536 - page 49

    E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 27 atm bundle add Add a new bundle of interfaces. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm bundle add name = <string> name The name of the new bundle. REQUIRED =>atm bundle add name=myBundle =>atm bundle list myBundle: Connection state : not-connected Retry: 10 Policy: priority Propagate ...

  • Technicolor - Thomson ST536 - page 50

    E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 28 atm bundle attach Attach a bundle of interfaces. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm bundle attach name = <string> name The name of the b undle to be attached. REQUIRED =>atm bundle attach name=myBundle =>atm bundle list myBundle: Connection state : connected Retry: 10 Policy: p ...

  • Technicolor - Thomson ST536 - page 51

    E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 29 atm bundle config Modify a bundle of interf aces. SYNT AX: where: EXAMPLE: i The bundle of interfaces to be configu red must not be connected at the time of configuration. If this should be the case , use the command :atm bundle de tach before using the command :atm bundle c onfig . atm bundle config na ...

  • Technicolor - Thomson ST536 - page 52

    E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 30 atm bundle clear Clear the bundle statistics. SYNT AX: where: atm bundle clear [name = <string>] name The name of the b undle for wh ich the statistics must be cleared. Note If not specified, t he statistics for all the bund les will be cleared. OPTIONAL ...

  • Technicolor - Thomson ST536 - page 53

    E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 31 atm bundle delete Delete a bundle of interfaces. SYNT AX: where: RELA TED COMMANDS: atm bundle delete name = <string> name The name of the bundle to be deleted. REQUIRED atm bundle add Add a new bundle of interfaces. atm bundle list Display the current bundles. ...

  • Technicolor - Thomson ST536 - page 54

    E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 32 atm bundle detach Detach a bundle of interfac es. SYNT AX: where: RELA TED COMMANDS: atm bundle detach intf = <string> intf The na me of the bundle to be detached . REQUIRED atm bundle attach Attach a bu ndle of interfaces. ...

  • Technicolor - Thomson ST536 - page 55

    E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 33 atm bundle flush Flush all bund les. SYNT AX: atm bundle flush ...

  • Technicolor - Thomson ST536 - page 56

    E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 34 atm bundle ifadd Add an interface on a bundle. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: i Up to 8 interfaces or (sub-)bund les can be added to one bund le. atm bundle ifadd name = <string> intf = <string> [index = <number{0-6}>] name The name of the bundle to which an A TM interfac ...

  • Technicolor - Thomson ST536 - page 57

    E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 35 atm bundle ifconfig Configure an interface from a bundle. SYNT AX: where: i The interface to be configured must not be connected at the tim e of configuration. If this should be the case, use the command :atm bundle ifde tach before using th e command :atm bundle ifconfig . atm bundle ifconfig name = &l ...

  • Technicolor - Thomson ST536 - page 58

    E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 36 atm bundle ifdelete Remove an interface from a bundle. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm bundle ifdelete name = <string> intf = <string> name The name of the b undle from which an A TM interface must be removed. RE QUIRED intf The name of the A TM inte rface to be removed. REQ ...

  • Technicolor - Thomson ST536 - page 59

    E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 37 atm bundle list Display the current bundles. SYNT AX: EXAMPLE: RELA TED COMMANDS: atm bundle list =>atm bundle list Test : Connection state : not-connected Retry: 10 Policy: priority TX requested bytes: 0 requested frames: 0 TX bytes: 0 frames: 0 RX bytes: 0 frames: 0 Interface: Test State: enabled S ...

  • Technicolor - Thomson ST536 - page 60

    E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 38 atm cac config Configure the A TM connec tion admission co ntrol. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm cac config config port = <{dsl0|dsl1|atm2|atm3|aal5|atm5} or number> state = <{disabled|enabled}> config port The port for which CAC is co nfigured. REQUIRED state Enable/disa b ...

  • Technicolor - Thomson ST536 - page 61

    E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 39 atm cac list Display all the CAC parameters. SYNT AX: EXAMPLE: RELA TED COMMANDS: atm cac list {Administrator}[atm cac]=>list CAC: port: dsl0 state: enabled CAC: port: dsl1 state: enabled CAC: port: atm2 state: enabled CAC: port: aal5 state: disabled CAC: port: atm5 state: disabled Overbooking: realt ...

  • Technicolor - Thomson ST536 - page 62

    E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 40 atm cac overbooking Configure A TM overboo king parameters. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm cac overbooking rt = <number{0-1000}> nrt = <number{0-1000}> rt A number between 0 and 1000. The realtime overbooking perc entage. REQUIRED nrt A number between 0 and 1000. The non-re ...

  • Technicolor - Thomson ST536 - page 63

    E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 41 atm debug aal5stats Display A TM Adaptation Layer 5 (AAL 5) port specific A TM statistics. SYNT AX: where: RELA TED COMMANDS: atm debug aal5stats port = <{dsl0|dsl1|atm2|atm3|aal5|atm5} or number> vpi = <number{0-15}> [vci = <number{0-511}>] [clear = <{disabled | enabled}>] port ...

  • Technicolor - Thomson ST536 - page 64

    E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 42 atm debug gstats Display A TM global statistics. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm debug gstats [clear = <{disabled | enabled}>] clear Enabl e or disable clearing of the statistics after request. OPTIONAL {admin}[atm debug]=>gstats # of received octets = 1802. # of transmitted oc ...

  • Technicolor - Thomson ST536 - page 65

    E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 43 atm debug portstats Display port specific A TM statistics. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm debug portstats port = <{dsl0} or number> [clear = <{disabled | enabled}>] port The port number for whic h statistics will be retrieved. Choose between: > DSL0 Or specify a port numb ...

  • Technicolor - Thomson ST536 - page 66

    E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 44 atm oam config Modify the A TM Operation and Maintenance (OAM) settings. SYNT AX: where: RELA TED COMMANDS: atm oam config [clp = <number{0-1}>] [loopbackid = <string>] clp A number (0 or 1). Represents th e Cell Loss Priority (CLP) bit value of the OAM cells. The default is 1 . OPTIONAL lo ...

  • Technicolor - Thomson ST536 - page 67

    E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 45 atm oam list Display the A TM OAM settings. SYNT AX: EXAMPLE: RELA TED COMMANDS: atm oam list =>atm oam list OAM config dump ------------------- CLP bit value : 1 Loopback id : 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a OAM data blocking mode -------------------------- Port dsl0: blocking Port d ...

  • Technicolor - Thomson ST536 - page 68

    E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 46 atm oam modify Modify the A TM OAM data b locking mode. SYNT AX: where: atm oam modify port = <{dsl0} or number> blocking = <{disabled | enabled}> port The port for which OA M blocking is configur ed. Choose between: > DSL0 Or specify a port numb er (dsl0 has port number 0). REQUIRED blo ...

  • Technicolor - Thomson ST536 - page 69

    E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 47 EXAMPLE: RELA TED COMMANDS: =>atm oam list OAM config dump ------------------- CLP bit value : 1 Loopback id : 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a OAM data blocking mode -------------------------- Port dsl0: blocking Port dsl1: blocking Port atm2: blocking Port atm3: blocking Port aal5: b ...

  • Technicolor - Thomson ST536 - page 70

    E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 48 atm oam ping Send A T M loopback cells. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm oam ping dest = <string> [count = <number{1-1000000}>] [interval = <number{100-1000000}>] dest The destination address for the request. This can be any A TM phonebook entry . REQUIRED count A numbe ...

  • Technicolor - Thomson ST536 - page 71

    E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 49 atm oam cc list Display Continuity Che ck (CC) configuration. SYNT AX: EXAMPLE: RELA TED COMMANDS: atm oam cc list =>atm oam cclist PORT = 0 VPI = 15 VCI = 16 End2End Mode = Auto Segment Mode = Auto PORT = 0 VPI = 0 VCI = 35 End2End Mode = Auto Segment Mode = Auto PORT = 0 VPI = 8 VCI = 35 End2End Mo ...

  • Technicolor - Thomson ST536 - page 72

    E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 50 atm oam cc modify Modify CC on the connection . SYNT AX: where: RELA TED COMMANDS: atm oam modify port = <{dsl0|dsl1|atm2|atm3|aal5|atm5} or number> vpi = <number{0-15}> [vci = <number{0-511}>] [transmit = <{disabled | enabled}>] [receive = <{disabled | enabled}>] [auto = ...

  • Technicolor - Thomson ST536 - page 73

    E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 51 atm oam cc send Send CC activate/deact ivate to connection. SYNT AX: where: RELA TED COMMANDS: atm oam cc send port = <{dsl0} or number> vpi = <number{0-15}> [vci = <number{0-511}>] [span = <{segment | end2end}>] [action = <{activate | deactivate}>] [direction = <{source ...

  • Technicolor - Thomson ST536 - page 74

    E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 52 atm oam vclb add Create a loopback connection for VC. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm oam vclb add port = <{dsl0} or number> vpi = <number{0-15}> [vci = <number{0-511}>] port The A TM port number . Choose between: > DSL0 Or specify a port number (dsl0 has port numbe ...

  • Technicolor - Thomson ST536 - page 75

    E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 53 atm oam vclb del Delete a loop back connection for VC. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm oam vclb del port = <{dsl0} or number> vpi = <number{0-15}> [vci = <number{0-511}>] port The A TM port number . Choose between: > DSL0 Or specify a port number (dsl0 has port numbe ...

  • Technicolor - Thomson ST536 - page 76

    E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 54 atm oam vclb list List all VC loopback connections. SYNT AX: EXAMPLE: RELA TED COMMANDS: atm oam vclb list =>atm oam vclb list PORT = 0 VPI = 0 VCI = 36 PORT = 1 VPI = 0 VCI = 37 => atm oam vclb add Create a loopback co nnection for VC. atm oam vclb del Delete a loopba ck connection for VC. ...

  • Technicolor - Thomson ST536 - page 77

    E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 55 atm phonebook add Add a new phonebook entry . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm phonebook add name = <string> addr = <atmchannel : PVC syntax is [port.]vpi.vci port=dsl0 | ...> name The name of the new ph onebook entry . This name ca n be freely ch osen , however two li mitatio ...

  • Technicolor - Thomson ST536 - page 78

    E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 56 atm phonebook autolist Show the auto PVCs. SYNT AX: EXAMPLE: RELA TED COMMANDS: i Auto PVCs are only shown if they are su pported by the Central Office DSLAM. atm phonebook autolist =>atm phonebook autolist 8.35 => atm phonebook list Display the current phonebook. ...

  • Technicolor - Thomson ST536 - page 79

    E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 57 atm phonebook delete Delete an existing ph onebook entry . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: i This command is only ap plicable for phonebook entries that are not used (in other wo rds, not configured for any packet service). atm phonebook delete name = <string> name The name of the pho ...

  • Technicolor - Thomson ST536 - page 80

    E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 58 atm phonebook flush Flush all the phoneb ook entries. SYNT AX: EXAMPLE: i 1. Phonebook entries that ar ei nu s e ,c a n n o tb ef l u s h e d . 2. This command does not impa ct pre viously saved configurations. atm phonebook flush =>atm phonebook list Name Use Address atm_pvc_0_35 1 0.35 RtPPPoA 0 8 ...

  • Technicolor - Thomson ST536 - page 81

    E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 59 atm phonebook list Display the current phonebook. SYNT AX: EXAMPLE: RELA TED COMMANDS: atm phonebook list =>atm phonebook list Name Use Address atm_pvc_0_35 1 0.35 RtPPPoA 0 8.35 => atm phonebook add Add a new phoneboo k entry . atm phonebook autoli st Show the auto PVCs. atm phonebook del ete Del ...

  • Technicolor - Thomson ST536 - page 82

    E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 60 atm qosbook add Add a new QoS book entry . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm qosbook add name = <string> [txctd = <string>] [rxctd = <string>] name The name of the new QoS entry . REQUIRED txctd The name of the Co nformance T ra ffic Descriptor (CTD) for the transmit (up ...

  • Technicolor - Thomson ST536 - page 83

    E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 61 atm qosbook config Modify the QoS book configuration . SYNT AX: where: EXAMPLE: atm qosbook config [format = <{bytes | cells}>] format The in put/output format of the QoS book. Choose between: > byte s : the output is shown in Kbits or bytes. > cells : the output is shown in cps or cells. Th ...

  • Technicolor - Thomson ST536 - page 84

    E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 62 atm qosbook ctdadd Add a Connection T ra ffic Descriptor (CTD). SYNT AX: where: EXAMPLE: atm qosbook ctdadd name = <string> conformance = <{UBR | CBR | VBR }> [peakrate = <number{0-27786}>] [sustrate = <number{0-27786} [maxburst = <number{0-12240}>] [realtime = <{enabled | ...

  • Technicolor - Thomson ST536 - page 85

    E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 63 IMPORT ANT NOTE: The Thomson ST always rounds up specified burst sizes to a multiple of 48 by tes (a multiple of A TM cells). Example: In the example below a burst size of 100 bytes is specified (maxburst=100). The Thomson ST will round up the burst size to the closest matching multiple of 48 bytes, as ...

  • Technicolor - Thomson ST536 - page 86

    E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 64 atm qosbook ctddelete Delete a C TD. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm qosbook ctddelete name = <string> [force = <{disabled | enabled}>] name The name of the C TD entry to be deleted. REQUIRED force Enable or disable to force delete the entry even when it is still in use. The ...

  • Technicolor - Thomson ST536 - page 87

    E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 65 atm qosbook ctdlist Display all CTDs. SYNT AX: EXAMPLE: RELA TED COMMANDS: atm qosbook ctdlist =>atm qosbook ctdlist Name Ref Conf Peak Sust Burst Minrate Frame Cdvt RT FD (Kbits) (Kbits) (bytes) (Kbits) (bytes) default 2 UBR linerate 0 0 0 0 0 disabled disab led High 0 CBR 27786 0 0 0 0 0 disabled d ...

  • Technicolor - Thomson ST536 - page 88

    E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 66 atm qosbook delete Delete a QoS b ook entry . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm qosbook delete name = <string> [force = <{disabled | enabled}>] name The name of the QoS book entry to be d eleted. REQUIRED force Enable or disable to force delete the entry even when it is still ...

  • Technicolor - Thomson ST536 - page 89

    E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 67 atm qosbook flush Flush all the QoS book entries. SYNT AX: i The flush command do es not impact previously save d configuration s. atm qosbook flush ...

  • Technicolor - Thomson ST536 - page 90

    E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 68 atm qosbook list Display the QoS book. SYNT AX: EXAMPLE: RELA TED COMMANDS: atm qosbook list =>atm qosbook list Name Ref Type TX peak sust burst RX peak sust burst framediscard (Kbits) (Kbits) (bytes) (Kbits) (Kbits) (bytes) default 3 ubr linerate 0 0 linerate 0 0 disabled TestVBR 0 vbr-nrt 1500 100 ...

  • Technicolor - Thomson ST536 - page 91

    E-DOC-CTC-20061 027-0003 v2.0 AutoPVC Commands 69 4 AutoPVC Commands Introduction This chapter describes the commands of the autopv c command group. Contents This chapter covers th e following commands: autopvc config Configure autopvc. 70 autopvc list Show the retrie ved information. 72 ...

  • Technicolor - Thomson ST536 - page 92

    E-DOC-CTC- 20061027-0003 v2 .0 AutoPVC Commands 70 autopvc config Configure autopvc. SYNT AX: where: autopvc config [mode = <{pseudo | passive | active}>] [type = <{bridge | pppoerelay | ipoa | ethoa | pppoa | pppoe }>] [overwrite = <{disabled | enabled}>] [peakrate = <number{0-27786}>] mode Select the autopvc mode: > pse ...

  • Technicolor - Thomson ST536 - page 93

    E-DOC-CTC-20061 027-0003 v2.0 AutoPVC Commands 71 EXAMPLE: =>autopvc config Autopvc mode : passive Autopvc type : Autopvc standard: unknown Autopvc pseudo : unknown UBR overwrite : disabled UBR peak rate : linerate => ...

  • Technicolor - Thomson ST536 - page 94

    E-DOC-CTC- 20061027-0003 v2 .0 AutoPVC Commands 72 autopvc list Show the retrieved information. SYNT AX: where: EXAMPLE: autopvc list [table = <{Port | AtmLayer | Vpc | Vcc | Address | AddressRegistrationAdmin | AtmServiceType | AtmServiceConnectionInfo | AAL1Profile | | AAL34Profile | AAL5Profile | AAL2CommonProfile | AAL2TrunkingProfile | AAL2 ...

  • Technicolor - Thomson ST536 - page 95

    E-DOC-CTC-20061 027-0003 v2.0 Config Commands 73 5 Config Commands Introduction This chapter describes the commands of the config command group. Contents This chapter covers th e following commands: config delete Delete a user con figuration file. 74 config dump Show the saved configuration file. 75 config flush Flush the loaded configuration. 76 c ...

  • Technicolor - Thomson ST536 - page 96

    E-DOC-CTC- 20061027-0003 v2 .0 Config Commands 74 config delete Delete a user configuration file. SYNT AX: where: RELA TED COMMANDS: config delete [filename = <string>] filename Name of the user con figuration file to b e deleted. Note If not specified, all the user con f iguration files that were saved in the Thomson ST permanent storage wil ...

  • Technicolor - Thomson ST536 - page 97

    E-DOC-CTC-20061 027-0003 v2.0 Config Commands 75 config dump Show the saved configuratio n file. SYNT AX: where: RELA TED COMMANDS: config dump [sections = <string>] sections Sections to be dumped OP TIONAL config delete Delete a user configuration fi le. ...

  • Technicolor - Thomson ST536 - page 98

    E-DOC-CTC- 20061027-0003 v2 .0 Config Commands 76 config flush Flush the loaded configu ration. SYNT AX: where: i 1. This flush command combines all the possible fl ush commands. 2. This command does not affect saved configurations. config flush [flush_ip = <{enabled | disabled}>] flush_ip Flush IP settings (enabled) or not (dis abled). The d ...

  • Technicolor - Thomson ST536 - page 99

    E-DOC-CTC-20061 027-0003 v2.0 Config Commands 77 config list Show the current configuration set. SYNT AX: where: RELA TED COMMANDS: config list [templates = <{disabled | enabl ed}>] templates List the template file s (disabled) or not (enabled). The default is disabled . OP TIONAL config load Load complete saved (backup) or default configurat ...

  • Technicolor - Thomson ST536 - page 100

    E-DOC-CTC- 20061027-0003 v2 .0 Config Commands 78 config load Load complete saved (backup) or default configuration file. SYNT AX: where: i Use the command :config fl ush before loading a conf iguration file . config load [load_ip = <{enabled | disabled }>] [defaults = <{enabled | disabled}>] [flush = <{enabled | disabled}>] [echo ...

  • Technicolor - Thomson ST536 - page 101

    E-DOC-CTC-20061 027-0003 v2.0 Config Commands 79 EXAMPLE: RELA TED COMMANDS: =>ip rtlist Destination Source Gateway Intf Mtrc 10.0.0.0/24 10.0.0.0/24 10.0.0.140 eth0 0 172.16.0.5/32 0.0.0.0/0 172.16.0.5 cip1 0 10.0.0.140/32 0.0.0.0/0 10.0.0.140 eth0 0 127.0.0.1/32 0.0.0.0/0 127.0.0.1 loop 0 172.16.0.0/24 0.0.0.0/0 172.16.0.5 cip1 1 =>config l ...

  • Technicolor - Thomson ST536 - page 102

    E-DOC-CTC- 20061027-0003 v2 .0 Config Commands 80 config save Store the current config uration in a backup file. All the existing configurations an d modifi cations entered by the user are saved. The backup file is saved in the Thomson ST permanent storage. This fil e can be downloaded via th e Thomson ST web pages or via an F TP session . SYNT AX: ...

  • Technicolor - Thomson ST536 - page 103

    E-DOC-CTC-20061 027-0003 v2.0 Connection Commands 81 6 Connection Commands Introduction This chapter describes the commands of the connec tion command group. Contents This chapter covers th e following commands: connection appconfig Configure the avail able CONN/NA T application helpers. 82 connection appinfo Disp lay CONN/NA T application specific ...

  • Technicolor - Thomson ST536 - page 104

    E-DOC-CTC- 20061027-0003 v2 .0 Connection Commands 82 connection appconfig Configure the available CONN/ NA T application hel pers. SYNT AX: where: connection appconfig application = <string> [trace = <{disabled | enabled}>] [timeout = <number{0-32000}>] [floating = <{disabled | enabled}>] [childqos = <{DSCP|Interactive| ...

  • Technicolor - Thomson ST536 - page 105

    E-DOC-CTC-20061 027-0003 v2.0 Connection Commands 83 EXAMPLE: RELA TED COMMANDS: =>connection applist Application Proto DefaultPort Traces Timeout IP6TO4 6to4 0 enabled unavailable PPTP tcp 1723 enabled unavailable ESP esp 0 unavailable 15' 0" IKE udp 500 disabled 15' 0" FLOATING SIP udp 5060 disabled 6 0" trace level 1 ...

  • Technicolor - Thomson ST536 - page 106

    E-DOC-CTC- 20061027-0003 v2 .0 Connection Commands 84 connection appinfo Display CONN/NA T application specific info. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: connection appinfo application = <{string} > application The name of a CONN /NA T application helper . Ti p Use the command :conne ction applist to obtain a list of CONN/NA T applica ...

  • Technicolor - Thomson ST536 - page 107

    E-DOC-CTC-20061 027-0003 v2.0 Connection Commands 85 connection applist List the available CONN/N A T application helpers. SYNT AX: EXAMPLE: RELA TED COMMANDS: connection applist =>connection applist Application Proto DefaultPort Traces Timeout IP6TO4 6to4 0 enabled unavailable PPTP tcp 1723 enabled unavailable ESP esp 0 unavailable 15' 0&q ...

  • Technicolor - Thomson ST536 - page 108

    E-DOC-CTC- 20061027-0003 v2 .0 Connection Commands 86 connection bind Create a new CONN/NA T applic ation helper/port bind ing. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: connection bind application = <string> port = <port-range> application The name of a CONN /NA T application helper . Ti p Use the command :conne ction applist to obta ...

  • Technicolor - Thomson ST536 - page 109

    E-DOC-CTC-20061 027-0003 v2.0 Connection Commands 87 connection bindlist List the current CONN/NA T application helper/port bindings. SYNT AX: EXAMPLE: RELA TED COMMANDS: connection bindlist =>connection bindlist Application Proto Portrange Flags LOOSE(UDP) udp 67 JABBER tcp 15222 JABBER tcp 5222 FTP tcp 21 IRC tcp 6660-6669 H323 tcp 1720 ILS tc ...

  • Technicolor - Thomson ST536 - page 110

    E-DOC-CTC- 20061027-0003 v2 .0 Connection Commands 88 connection clean Clean the connection da tabase by forcing tim eouts. SYNT AX: where: EXAMPLE: connection clean [level = <number{0-9}>] level A number betwee n 0 and 9. Represents the desired scrubbing level. OPTIONAL =>connection list ID proto state substate flags timeout -- ----- ---- ...

  • Technicolor - Thomson ST536 - page 111

    E-DOC-CTC-20061 027-0003 v2.0 Connection Commands 89 connection clear Kill all the connections. SYNT AX: EXAMPLE: connection clear =>connection clear Connection to host lost. ...

  • Technicolor - Thomson ST536 - page 112

    E-DOC-CTC- 20061027-0003 v2 .0 Connection Commands 90 connection config Configure the connection handling. SYNT AX: where: EXAMPLE: connection config [configchangemode = <{i mmediate | delayed}>] [probes = <{disabled | enabled}>] [udptrackmode = <{strict | loose}>] configchangemode Select how configuration changes are handled. Cho ...

  • Technicolor - Thomson ST536 - page 113

    E-DOC-CTC-20061 027-0003 v2.0 Connection Commands 91 connection debug The connection debug commands SYNT AX: where: EXAMPLE: connection debug [trace = <{disabled|enabled}>] trace E nable or disable traces. The default is disab led . OPTIONAL =>connection debug connection traces : disabled => =>connection debug trace enabled => =&g ...

  • Technicolor - Thomson ST536 - page 114

    E-DOC-CTC- 20061027-0003 v2 .0 Connection Commands 92 connection describe Describe the streams of a connect ion. SYNT AX: where: EXAMPLE: connection describe [id = <number{0-2048}>] id A number between 0 and 2048. Represents the ID of the connection to be described. Note If not specified, the connection with ID 0 will be described. Ti p Use t ...

  • Technicolor - Thomson ST536 - page 115

    E-DOC-CTC-20061 027-0003 v2.0 Connection Commands 93 connection flush Flush the current con nection configuration. SYNT AX: connection flush ...

  • Technicolor - Thomson ST536 - page 116

    E-DOC-CTC- 20061027-0003 v2 .0 Connection Commands 94 connection info Show all the registered modules with some info. SYNT AX: EXAMPLE: connection info =>connection info Registered connection modules : - Module : FW, holds private data (F:10264 S:6592). - Module : IDS, holds private data (F:0 S:0). - Module : NAT, holds private data (F:0 S:0). R ...

  • Technicolor - Thomson ST536 - page 117

    E-DOC-CTC-20061 027-0003 v2.0 Connection Commands 95 connection list Display the currentl y known connection s. SYNT AX: where: EXAMPLE: connection list [nr = <number{1-2048}>] [string = <string>] [beginstring = <string>] nr A number between 1 and 2048. Represents the number of connections to be displayed. Note If not specified, a ...

  • Technicolor - Thomson ST536 - page 118

    E-DOC-CTC- 20061027-0003 v2 .0 Connection Commands 96 connection refresh Invalidate all the cached decisions. SYNT AX: connection refresh ...

  • Technicolor - Thomson ST536 - page 119

    E-DOC-CTC-20061 027-0003 v2.0 Connection Commands 97 connection stats Display the connection and stream statistics. SYNT AX: EXAMPLE: connection stats =>connection stats Connection statistics: ------------------------------------------- Maximum number of connections : 1024 Maximum number of halfopen connections : 1024 --------------------------- ...

  • Technicolor - Thomson ST536 - page 120

    E-DOC-CTC- 20061027-0003 v2 .0 Connection Commands 98 connection timerclear Clear the connection timeout to default. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: connection timercl ear [timer = <{tcpidle|tcpneg|tcpkill|udpidle|udpkill| icmpkill|ipidle|ipkill}>] timer The name of the connecti on idle timer to be reset. Note If not specified, al ...

  • Technicolor - Thomson ST536 - page 121

    E-DOC-CTC-20061 027-0003 v2.0 Connection Commands 99 connection timerconfig Configure the conn ection timeout handl ing. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: connection timerconfig [timer = <{tcpidle|tcpneg|tcpkill|udpidle|udpkill| icmpkill|ipidle|ipkill}>] [value = <number{0-86400}>] timer The name of the conn ection idle timer ...

  • Technicolor - Thomson ST536 - page 122

    E-DOC-CTC- 20061027-0003 v2 .0 Connection Commands 100 connection unbind Delete an existing CONN/NA T application helper/port bindi ng. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: connection unbind application = <string> port = <port-range> application The name of a CONN /NA T application helper . Ti p Use the command :conne ction appli ...

  • Technicolor - Thomson ST536 - page 123

    E-DOC-CTC-20061 027-0003 v2.0 CWMP Commands 101 7 CWMP Commands Introduction This chapter describes the commands of the cwmp (CPE W AN Managemen t Protocol) command grou p. Contents This chapter covers th e following commands: cwmp config Configure the cwmpd as seen fr om the ACS. 102 cwmp server config Configure the cwmp d towards the ACS. 104 ...

  • Technicolor - Thomson ST536 - page 124

    E-DOC-CTC- 20061027-0003 v2 .0 CWMP Commands 102 cwmp config Configure the cwmpd as seen from the ACS. SYNT AX: where: cwmp config [state = <{disabled|enabled}>] [mode = <{readonly|full}>] [periodicInform = <{disabled|enabled}>] [periodicInfInt = <number>] [sessionTimeout = <number>] [noIpTimeout = <number>] [max ...

  • Technicolor - Thomson ST536 - page 125

    E-DOC-CTC-20061 027-0003 v2.0 CWMP Commands 103 EXAMPLE: connectionRequest Set the connection request flag of the cwmp daemon. Choose between: > enabled > disabled. The default is enabled . OP TIONAL connectionReqPath Set the path where th e cwmp daemon can be reached. OP TIONAL connectionReqUserNam e Set the username the ACS must use to log ...

  • Technicolor - Thomson ST536 - page 126

    E-DOC-CTC- 20061027-0003 v2 .0 CWMP Commands 104 cwmp server config Configure the cwmpd towards the ACS. SYNT AX: where: EXAMPLE: cwmp server config [url = <string>] [username = <string>] [password = <string>] url Set the HTTP URL used to contact the ACS server . OP TIONAL username Set the username for ACS Digest Authenti cation. ...

  • Technicolor - Thomson ST536 - page 127

    E-DOC-CTC-20061 027-0003 v2.0 Debug Commands 105 8 Debug Commands Introduction This chapter describes the commands of the debug comman d group. Contents This chapter covers th e following commands: debug exec Execute a 'T race & Debug' command. 106 ...

  • Technicolor - Thomson ST536 - page 128

    E-DOC-CTC- 20061027-0003 v2 .0 Debug Commands 106 debug exec Execute a 'T race & Debug' command. SYNT AX: where: ! This comman d is for qualifie d personnel onl y . debug exec cmd = <quoted string> cmd A quoted 'T race & Deb u g' command string. REQUIRED ...

  • Technicolor - Thomson ST536 - page 129

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 107 9 DHCP Commands Introduction This chapter describ es the commands of the Dynamic Host Config uration Protoc ol (DHCP) command grou p. Contents This chapter covers th e following commands: dhcp client flush Delete al l the DHCP leases. 109 dhcp client ifa dd Create a DHCP client. 110 dhcp client ifa tt ...

  • Technicolor - Thomson ST536 - page 130

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 108 dhcp relay ruledelete Delet e a selection rule from a DHCP forw ard entry . 142 dhcp rule add Add a rule for DHCP condition al selection. 143 dhcp rule debug t raceconfig Modify DHCP ru le trace configuration. 144 dhcp rule delete Delete a DHCP rule. 145 dhcp rule flush Flush all DHCP rules. 146 dhcp ...

  • Technicolor - Thomson ST536 - page 131

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 109 dhcp client flush Delete all the DHCP lea ses. SYNT AX: i The flush command does not impact previously saved configurations. dhcp client flush ...

  • Technicolor - Thomson ST536 - page 132

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 110 dhcp client ifadd Create a DHCP client. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp client ifadd intf = <string> [defrqoptions = <{disabled|enabled}>] intf The name of the dynamic interface for which a DHCP lease must be created. REQUIRED defrqoptions Enable/Disable the creation of t ...

  • Technicolor - Thomson ST536 - page 133

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 111 dhcp client ifattach Activate a DHCP client. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp client ifattach intf = <string> intf The name of the dyn amic interface for which a DHCP client was created. REQUIRED =>dhcp client iflist myPPP_ppp : [INIT] flags = bc dns rt IP address : 0.0.0.0 HW ...

  • Technicolor - Thomson ST536 - page 134

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 112 dhcp client ifconfig Configure a DHCP client. SYNT AX: where: RELA TED COMMANDS i Use the command :dhcp cli ent ifrele ase before configurin g the dhcp client. dhcp client ifconfig intf = <string> [label = <label name>] [metric = <number{0-255}>] [dnsmetric = <number{0-100}>] ...

  • Technicolor - Thomson ST536 - page 135

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 113 dhcp client ifdelete Delete a DHCP client. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp client ifdelete intf = <string> intf The name of the dynami c inte rface for which the DHCP lease must be deleted. REQUIRED =>dhcp client iflist myPPP_ppp : [INIT] flags = bc dns rt IP address : 10.0.0 ...

  • Technicolor - Thomson ST536 - page 136

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 114 dhcp client ifdetach De-activate a DHCP client and releases its lease. SYNT AX: where: RELA TED COMMANDS: ifdetach intf = <string> intf The name of the dyn amic interface. REQUIRED dhcp client ifa ttach Activ ate a DHCP client. dhcp client ifre new Renew the DHCP lease. dhcp client ifli st List ...

  • Technicolor - Thomson ST536 - page 137

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 115 dhcp client iflist List all the DHCP leases attached to dyna mic interfaces. SYNT AX: where: EXAMPLE: EXAMPLE INPUT/OUTPUT IN A NETWORKED ENVIRONMENT : The Thomson ST is configured as DHCP client di sabled its Ethernet interface eth0. dhcp client iflist [intf = <string>] [expand = <{disabled| ...

  • Technicolor - Thomson ST536 - page 138

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 116 RELA TED COMMANDS: dhcp client ifa dd Create a DHCP client. dhcp client ifdel ete Delete a DHCP client. ...

  • Technicolor - Thomson ST536 - page 139

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 117 dhcp client ifrenew Renew the DHCP lease. SYNT AX: where: EXAMPLE 1: dhcp client ifrenew intf = <string> intf The name of the dynami c inte rface for which the DHCP lease must be renewe d. REQUIRED =>dhcp client iflist NewETHoA : [BOUND] flags= uc IP address : 10.0.0.10 HW address : 00:90:d0: ...

  • Technicolor - Thomson ST536 - page 140

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 118 EXAMPLE 2: The Thomson ST is configured as DHCP client di sabled its Ethernet interface eth0. RELA TED COMMANDS: =>dhcp client stats DHCP client statistics: Corrupted packet recv : 0 OFFERs recv : 0 ACKs recv : 0 NAKs recv : 0 Pure BOOTP REPLIES : 0 Other message types : 0 DISCOVERs sent : 0 REQUE ...

  • Technicolor - Thomson ST536 - page 141

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 119 dhcp client debug clear Clear the DHCP client statistics. SYNT AX: EXAMPLE: RELA TED COMMANDS: dhcp client debug clear =>dhcp client debug stats DHCP client statistics: Corrupted packet recv : 0 OFFERs recv : 0 ACKs recv : 0 NAKs recv : 0 Pure BOOTP REPLIES : 0 Other message types : 0 DISCOVERs sen ...

  • Technicolor - Thomson ST536 - page 142

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 120 dhcp client debug stats Print the DHCP cl ient statistics. SYNT AX: EXAMPLE: RELA TED COMMANDS: dhcp client debug stats =>dhcp client debug stats DHCP client statistics: Corrupted packet recv : 0 OFFERs recv : 1 ACKs recv : 1 NAKs recv : 0 Pure BOOTP REPLIES : 0 Other message types : 0 DISCOVERs s ...

  • Technicolor - Thomson ST536 - page 143

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 121 dhcp client debug traceconfig Modify the DHCP clie nt trace configuration. SYNT AX: where: EXAMPLE: dhcp client debug traceconfig [state = <{disabled | enabled}>] state Enable or disabl e tracing. The default is disabled . OPTIONAL =>dhcp client debug traceconfig tracing: disabled =>dhcp c ...

  • Technicolor - Thomson ST536 - page 144

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 122 dhcp client rqoptions add Add a DHCP Opti on Code to the Parameter Request List. SYNT AX: where: RELA TED COMMANDS: dhcp client rqoptions add intf = <string> option = <string or number> [index = <number{0-255}>] intf The name of the dyn amic interface. REQUIRED option The name or nu ...

  • Technicolor - Thomson ST536 - page 145

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 123 dhcp client rqoptions delete Delete a DHCP Option Code from the Parameter Request List. SYNT AX: where: RELA TED COMMANDS: dhcp client rqoptions delete intf = <string> option = <string or number> intf The name of the dyn amic interface. REQUIRED option The name or number of the option. OP ...

  • Technicolor - Thomson ST536 - page 146

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 124 dhcp client rqoptions list List all DHCP Optio n Codes in the Parameter Request List. SYNT AX: where: RELA TED COMMANDS: dhcp client rqoptions list [intf = <string>] intf The name of the d ynamic interface. OPTI ONAL dhcp client rqoption s delete Delete a DHCP Option Code from the Parameter Req ...

  • Technicolor - Thomson ST536 - page 147

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 125 dhcp client rqoptions optionlist List all DHCP Option Codes that can be used in the Para meter Request List. SYNT AX: RELA TED COMMANDS: dhcp client rqoptions optionlist dhcp client rqoption s add Add a DHCP Option Code to the Parame ter Request List. dhcp client rqoption s list List all DHCP Opti on ...

  • Technicolor - Thomson ST536 - page 148

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 126 dhcp client txoptions add Add an option . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp client txoptions add intf = <string> option = <string or number> value = <Value : (type)value; type being 8- bit, 16-bit, 32-bit, addr, ascii, byte_array, clientid> [index = <number{0-255}& ...

  • Technicolor - Thomson ST536 - page 149

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 127 dhcp client txoptions delete Delete an option. SYNT AX: where: RELA TED COMMANDS: dhcp client txoptions delete intf = <string> option = <string or number> intf The name of the d ynamic interface. REQUIRED option The name or number of the option. REQUIRED dhcp client txop tions list List al ...

  • Technicolor - Thomson ST536 - page 150

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 128 dhcp client txoptions list List all options. SYNT AX: RELA TED COMMANDS: dhcp client txoptions list dhcp client txoptio ns delete Delete an option. ...

  • Technicolor - Thomson ST536 - page 151

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 129 dhcp client txoptions optionlist Lists all DHCP Option C odes that can be used. SYNT AX: RELA TED COMMANDS: dhcp client txoptions optionlist dhcp client txoptio ns add Add an option. dhcp client txop tions list List all options. ...

  • Technicolor - Thomson ST536 - page 152

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 130 dhcp relay add Add an entry to the DHCP forward list. SYNT AX: where: RELA TED COMMANDS: dhcp relay add name = <string> name The forward entry name. REQUIRED dhcp relay delete Delete an entry from the DHCP forward list. dhcp relay list List the DHCP forward list. dhcp relay modify Modify an ent ...

  • Technicolor - Thomson ST536 - page 153

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 131 dhcp relay debug stats Show the DHCP relay statistics. SYNT AX: EXAMPLE: RELA TED COMMANDS: dhcp relay debug stats =>dhcp relay debug stats DHCP relay statistics ------------------------- Client packet relayed : 64 Server packet relayed : 0 Bogus relay agent : 0 Bogus giaddr recv : 0 Corrupt agent ...

  • Technicolor - Thomson ST536 - page 154

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 132 dhcp relay debug traceconfig Modify the DHCP relay trace configur ation. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp relay debug traceconfig [state = <{disabled | enabled}>] state Enable or disabl e tracing. The default is disabled . OPTIONAL =>dhcp relay debug traceconfig Tracing: disa ...

  • Technicolor - Thomson ST536 - page 155

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 133 dhcp relay config Set the DHCP relay con figuration settings. SYNT AX: where: EXAMPLE: dhcp relay config [agentinfo = <{disabled | enabled}>] [agentmismatch = <{disabled | enabled}>] agentinfo Set the relay ag ent info status (RFC3 046) enabled or disabled. The default is disabled . OPTION ...

  • Technicolor - Thomson ST536 - page 156

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 134 dhcp relay delete Delete an entry from the DHCP forward list. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp relay delete name = <string> name The forward entry name. REQUIRED =>dhcp relay delete name = lan1_to_127.0.0.1 :dhcp relay delete name=lan1_to_127.0.0.1 => dhcp relay add Add an ...

  • Technicolor - Thomson ST536 - page 157

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 135 dhcp relay flush Flush the DHCP relay settings. SYNT AX: EXAMPLE: i The flush command does not im pact previously saved configurations. dhcp relay flush =>dhcp relay list DHCP server Interface giaddr ------------------------------------------------------- 127.0.0.1 eth0 192.168.1.254 =>dhcp rela ...

  • Technicolor - Thomson ST536 - page 158

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 136 dhcp relay ifconfig Configure a DHCP relay interface. SYNT AX: where: dhcp relay ifconfig intf = <string> [relay = <{disabled | enabled}>] [maxhops = <number{0-16}>] [remoteid = <password>] [trusted = <{disabled | enabled}>] intf The name of the dynamic inter face to be ...

  • Technicolor - Thomson ST536 - page 159

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 137 EXAMPLE: =>dhcp relay iflist eth0 : admin state = up oper state = up max hops = 4 trusted = disabled remote id = Internet_trigger : admin state = down oper state = down max hops = 4 trusted = disabled remote id = Internet : admin state = down oper state = down max hops = 4 trusted = disabled remote ...

  • Technicolor - Thomson ST536 - page 160

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 138 dhcp relay iflist Show the configuration of the relay interfaces. SYNT AX: where: EXAMPLE: dhcp relay iflist [intf = <string>] intf The name of the d ynamic interface to be lis ted. Note If not specified, all the relay in terfaces will be shown. OPTIONAL =>dhcp relay iflist eth0 : admin stat ...

  • Technicolor - Thomson ST536 - page 161

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 139 dhcp relay list List the DHCP forward list. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp relay list [name = <string>] name The forward entry name. OP TIONAL =>dhcp relay list DHCP server Interface giaddr ------------------------------------------------------- 127.0.0.1 eth0 10.0.0.138 =&g ...

  • Technicolor - Thomson ST536 - page 162

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 140 dhcp relay modify Modify an entry from the DHCP forward list. SYNT AX: where: RELA TED COMMANDS: dhcp relay modify name = <string> [addr = <ip-address>] [intf = <{None | guest1 | dmz1 | wan1 | lan1 | Internet}>] [giaddr = <ip-address>] [script = <>] name The forward entr ...

  • Technicolor - Thomson ST536 - page 163

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 141 dhcp relay ruleadd Add a selection rule to a DHCP forward entry . SYNT AX: where: RELA TED COMMANDS: dhcp relay ruleadd name = <string> [key = <{or | and}>] rulename = <string> name The name of the forward entry . REQUIRED key The logical key of the selection rule. The default is or ...

  • Technicolor - Thomson ST536 - page 164

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 142 dhcp relay ruledelete Delete a selection rule from a DHCP forward entry . SYNT AX: where: RELA TED COMMANDS: dhcp relay ruledelete name = <string> rulename = <string> name The name of the forward entry . REQUIRED rulename The name of the DHCP sel ection rule. REQUIRED dhcp relay ruleadd A ...

  • Technicolor - Thomson ST536 - page 165

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 143 dhcp rule add Add a rule for DHCP conditional selection. SYNT AX: where: RELA TED COMMANDS: dhcp rule add name = <string> type = <{vci | uci | mac}> vci [!]= <quoted string> uci [!]= <quoted string> [match = <{exactly|as_substring}>] mac [!]= <hardware-address with wil ...

  • Technicolor - Thomson ST536 - page 166

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 144 dhcp rule debug traceconfig Modify DHCP ru le trace configuration. SYNT AX: where: dhcp rule debug traceconfig [state = {disabled | enabled}] state Set tracing to disabl ed or enable d. The default is disabled . OPTIONAL ...

  • Technicolor - Thomson ST536 - page 167

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 145 dhcp rule delete Delete a DHCP rule. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp rule delete name = <string> name The name of the DHCP rule. REQUIRED =>dhcp rule delete name = new :dhcp rule delete name=new => dhcp rule add Add a ru le for DHCP conditional selection. dhcp rule flush F ...

  • Technicolor - Thomson ST536 - page 168

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 146 dhcp rule flush Flush all DHCP rules. SYNT AX: EXAMPLE: RELA TED COMMANDS: dhcp rule flush =>dhcp rule list Name Use Value new 0 vci=test =>dhcp rule flush =>dhcp rule list Name Use Value => dhcp rule add Add a ru le for DHCP conditional selection. dhcp rule delete Delete a DHCP rule. dhc ...

  • Technicolor - Thomson ST536 - page 169

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 147 dhcp rule list List all DHCP rules. SYNT AX: EXAMPLE: RELA TED COMMANDS: dhcp rule list =>dhcp rule list Name Use Value new 0 vci=test => dhcp rule add Add a ru le for DHCP conditional selection. dhcp rule delete Delete a DHCP rule. dhcp rule flush Flush all DHCP rule s. ...

  • Technicolor - Thomson ST536 - page 170

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 148 dhcp server config Print the DHCP server c onfiguration settings . SYNT AX: where: dhcp server config [state = <{disabled | enabled}>] ...

  • Technicolor - Thomson ST536 - page 171

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 149 dhcp server flush Flush all DHCP s erver pool and leas e entries. SYNT AX: i The flush command does not impact previously saved configurations. dhcp server flush ...

  • Technicolor - Thomson ST536 - page 172

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 150 dhcp server policy Print the DHCP serv er policy settings. SYNT AX: where: dhcp server policy [verifyfirst = <disabled|enabled>] [trustclient = <disabled|enabled>] [rtbehaviour = <msft|standard|traditional>] ...

  • Technicolor - Thomson ST536 - page 173

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 151 dhcp server debug clear Clear the DHCP server statistics. SYNT AX: EXAMPLE: RELA TED COMMANDS: dhcp server debug clear =>dhcp server debug stats DHCP server state: Running DHCP server statistics: Corrupted packet recv : 0 DISCOVER : 2451 REQUEST : 28 DECLINE : 0 RELEASE : 22 INFORM : 1 Pure BOOTP R ...

  • Technicolor - Thomson ST536 - page 174

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 152 dhcp server debug stats Show the DHCP server statistics. SYNT AX: EXAMPLE: DESCRIPTION: > DHCP server stat e : the state of the DHCP se rver . > Cor r upted pack et recv : the number of corrupted packets (not co mplaint to RFC2131) received from the LAN. > DISCO VER : the number of DHCP serv ...

  • Technicolor - Thomson ST536 - page 175

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 153 > Ping table g ot full : whet her the history lis t of IP addr ess pings got full or not. These pi ngs are sent by th e DHCP server to verify whether the IP address is alr eady in use disabled the LAN or not (:dhcp server policy verifyfirst=yes). > Second DHCP serv er seen : whether a concurrent ...

  • Technicolor - Thomson ST536 - page 176

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 154 dhcp server debug traceconfig Modify the DHCP server trace configuration. SYNT AX: where: EXAMPLE: dhcp server debug traceconfig [state = <{disabled | enabled}>] state Enable or disabl e tracing. The default is disabled . OPTIONAL =>dhcp server debug traceconfig Tracing: disabled => ...

  • Technicolor - Thomson ST536 - page 177

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 155 dhcp server lease add Add a DHCP serv er lease. SYNT AX: where: dhcp server lease add clientid = <client-id> pool = <string> [addr = <ip-address>] [offset = <number>] [leasetime = <number>] [expirytime = <number>] [gateway = <ip-address>] [macaddr = <hardwa ...

  • Technicolor - Thomson ST536 - page 178

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 156 EXAMPLE: RELA TED COMMANDS: =>dhcp server lease list Lease Pool TTL State Clientid 0 0.0.0.0 dhcp_pool_1 00:26:40 FREE 00:90:D0:12:34:56 =>dhcp server lease add clientid=01:23:55:67:89:ab pool=Local_pool leasetime=3600 =>dhcp server lease list Lease Pool TTL State Clientid 0 0.0.0.0 dhcp_poo ...

  • Technicolor - Thomson ST536 - page 179

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 157 dhcp server lease delete Delete a DHCP server lease. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp server lease delete [clientid = <clientid | none>] [index = <number>] clientid The DHCP client identification stri ng of the DHCP lease. Note If not specified, all DH C P clients are delet ...

  • Technicolor - Thomson ST536 - page 180

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 158 dhcp server lease flush Flush all the DHCP server leases. SYNT AX: where: EXAMPLE: i The flush command does not impact previously saved configurations. dhcp server lease flush [pool = <string>] pool The name of the DHCP server pool to be flushed. Only the leases belonging to this pool wil l be ...

  • Technicolor - Thomson ST536 - page 181

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 159 dhcp server lease list List all the DHCP server lea ses. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp server lease list [clientid = <clientid | none>] [index = <number>] clientid The DHCP client identification stri ng of the DHCP lease. Note If not specified, th e DSHCP server leases f ...

  • Technicolor - Thomson ST536 - page 182

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 160 dhcp server option flush Flush all DHCP server option templates and instances. SYNT AX: i The flush command does not impact previously saved configurations. dhcp server option flush ...

  • Technicolor - Thomson ST536 - page 183

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 161 dhcp server option instadd Add a DHCP s erver option instance. SYNT AX: where: dhcp server option instadd name = <string> tmplname = <string> value = <Value : (type)value; type being 8- bit, 16-bit, 32-bit, addr, ascii, byte_array> name The name of the DHCP server op tion instance. R ...

  • Technicolor - Thomson ST536 - page 184

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 162 EXAMPLE: RELA TED COMMANDS: =>dhcp server option instlist myInstance Tmpl name : myTmpl (1) Use : 0 Value : (32-bit)64 =>dhcp server option instadd name=yourInstance tmplname=yourTmpl value=(ascii)&#33 {root}[dhcp server option]=>instlist yourInstance Tmpl name : yourTmpl (2) Use : 0 Val ...

  • Technicolor - Thomson ST536 - page 185

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 163 dhcp server option instdelete Delete a DHCP server option instance. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp server option instdelete name = <string> name The name of the DHCP server op ti on instance to be d eleted. REQUIRED =>dhcp server option instlist yourInstance Tmpl name : your ...

  • Technicolor - Thomson ST536 - page 186

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 164 dhcp server option instlist List all the DHCP serv er option instances. SYNT AX: EXAMPLE: RELA TED COMMANDS: dhcp server option instlist =>dhcp server option instlist yourInstance Tmpl name : yourTmpl (2) Use : 0 Value : (ascii)&#33 myInstance Tmpl name : myTmpl (1) Use : 0 Value : (32-bit)64 ...

  • Technicolor - Thomson ST536 - page 187

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 165 dhcp server option tmpladd Add a DHCP server o ption template. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp server option tmpladd name = <string> optionid = <number{1-254}> type = <{8-bit | 16-bit | 32-bit | addr | ascii | byte_array}> name The name of the DHCP server op tion tem ...

  • Technicolor - Thomson ST536 - page 188

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 166 dhcp server option tmpldelete Delete a DHCP server option template. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp server option tmpldelete name = <string> name The name of the DHCP server op ti on templa te to be deleted. REQUIR ED =>dhcp server option tmpllist Name Option Type Use yourTm ...

  • Technicolor - Thomson ST536 - page 189

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 167 dhcp server option tmpllist List all the DHCP serv er option templates. SYNT AX: EXAMPLE: RELA TED COMMANDS: dhcp server option tmpllist =>dhcp server option tmpllist Name Option Type Use yourTmpl 2 ascii 0 myTmpl 1 32-bit 0 => dhcp server option tmpladd Ad d a DHCP server option template. dhcp ...

  • Technicolor - Thomson ST536 - page 190

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 168 dhcp server pool add Add a DHCP server pool. SYNT AX: where: dhcp server pool add name = <string> [index = <number>] name The name of the DHCP server po ol. Note If not specified, the name i s “dhcp_pool_x”, where x is a subsequent number . REQUIRED index T he number of the pool be fo ...

  • Technicolor - Thomson ST536 - page 191

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 169 EXAMPLE: RELA TED COMMANDS: =>dhcp server pool list Pool Start End State PPP 0 dhcp_pool_1 0.0.0.0 0.0.0.0 FREE 1 My_LAN_Pool 10.0.0.1 10.0.0.254 USED 2 dhcp_pool_2 0.0.0.0 0.0.0.0 FREE =>dhcp server pool add =>dhcp server pool list Pool Start End State PPP 0 dhcp_pool_1 0.0.0.0 0.0.0.0 FREE ...

  • Technicolor - Thomson ST536 - page 192

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 170 dhcp server pool config Configure a DHCP server po ol. SYNT AX: where: dhcp server pool config name = <string> intf = <string> [index = <number>] [poolstart = <ip-address>] [poolend = <ip-address>] [netmask = <ip-mask(dotted or cidr)>] [gateway = <ipaddress | 0& ...

  • Technicolor - Thomson ST536 - page 193

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 171 EXAMPLE: gateway T he IP address of the defa ult gateway for the DHCP clients. The default value of th is parameter is 0 (not speci fied), which means that the gateway IP addr ess will be communicated by the remote server as soon as the PPP IPCP s ubnetmasking connection is establ ished or that the Th ...

  • Technicolor - Thomson ST536 - page 194

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 172 dhcp server pool delete Delete a DHCP server pool . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp server pool delete name = <string> name The name of the DHCP se rver pool to be deleted. Ti p Use the command :dhc p server pool list to obtain a lis t of all current DHCP leases. REQUIRED => ...

  • Technicolor - Thomson ST536 - page 195

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 173 dhcp server pool flush Flush all DHCP server pools. SYNT AX: EXAMPLE: i The flush command does not impact previously saved configurations. dhcp server pool flush =>dhcp server pool list Pool Start End Intf State 0 LAN_Private 10.0.0.1 10.0.0.254 eth0 USED 1 My_Pool 192.6.11.101 192.6.11.254 eth0 US ...

  • Technicolor - Thomson ST536 - page 196

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 174 dhcp server pool list List all DHCP server po ols. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp server pool list [name = <string>] name The name of the DHCP server po ol to be shown. Note If not specified, al l the DHCP server pools are shown. OPTIONAL =>dhcp server pool list Pool Start ...

  • Technicolor - Thomson ST536 - page 197

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 175 dhcp server pool optadd Add an option instance to the DHCP server po ol. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp server pool optadd name = <string> instname = <string> name The name of the DHCP server pool to which an option instance must be added. REQUIRED instname The name of th ...

  • Technicolor - Thomson ST536 - page 198

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 176 dhcp server pool optdelete Delete an option instan ce from the DHCP server pool. SYNT AX: where: dhcp server pool optdelete name = <string> instname = <string> name The name of the DHCP server po ol from which an optio n instance must be deleted. REQUIRED instname The name of the DHCP ser ...

  • Technicolor - Thomson ST536 - page 199

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 177 EXAMPLE: RELA TED COMMANDS: =>dhcp server pool list name=dhcp_pool_1 Pool Start End Intf State 1 dhcp_pool_1 0.0.0.0 0.0.0.0 lan1 FREE DHCP server = 0.0.0.0 [unnumbered] Netmask = 0.0.0.0 Leasetime = infinite Gateway = 0.0.0.0 DNS domain = lan DNS metric = 0 DNS address list: 0.0.0.0 (local DNS) Op ...

  • Technicolor - Thomson ST536 - page 200

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 178 dhcp server pool rtadd Add a route to the DHCP server pool. SYNT AX: where: RELA TED COMMANDS: dhcp server pool rtadd name = <string> dst = <ip-address> [dstmsk = <ip-mask(dotted or cidr)>] [gateway = <ipaddress | 0>] name The name of the DHCP server pool to which a route must ...

  • Technicolor - Thomson ST536 - page 201

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 179 dhcp server pool rtdelete Delete a route from the DHCP server pool. SYNT AX: where: RELA TED COMMANDS: dhcp server pool rtdelete name = <string> dst = <ip-address> [dstmsk = <ip-mask(dotted or cidr)>] [gateway = <ipaddress | 0>] name The name of the DHCP server pool from which ...

  • Technicolor - Thomson ST536 - page 202

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 180 dhcp server pool ruleadd Add a selection rule to th e DHCP ser ver pool. SYNT AX: where: RELA TED COMMANDS: dhcp server pool ruleadd name = <string> [key = {or | and}] rulename = <string> name The name of the DHCP server pool to which a selection rule must be added. REQUIRED key The logic ...

  • Technicolor - Thomson ST536 - page 203

    E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 181 dhcp server pool ruledelete Delete a sele ction rule from the DHCP se rver pool. SYNT AX: where: RELA TED COMMANDS: dhcp server pool ruleadd name = <string> rulename = <string> name The name of the DHCP server po ol from which a selection rule must be deleted. REQUIRED rulename The name of ...

  • Technicolor - Thomson ST536 - page 204

    E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 182 ...

  • Technicolor - Thomson ST536 - page 205

    E-DOC-CTC-20061 027-0003 v2.0 DNS Commands 183 10 DNS Commands Introduction This chapter describes the commands of the dns comman d group. Contents This chapter covers th e following commands: dns client config Modify the Domain Name System (DNS) resolver configura tion. 184 dns client dnsadd Add a DN S server . 185 dns client dnsdelete Delete a DN ...

  • Technicolor - Thomson ST536 - page 206

    E-DOC-CTC- 20061027-0003 v2 .0 DNS Commands 184 dns client config Modify the Domain Name System (DNS) resolver configuration. SYNT AX: where: EXAMPLE: dns client config [timeout = <number{1-900}>] [retry = <number{0-10}>] [search = <{disabled | enabled}>] [list = <string>] [trace = <{disabled | enabled}>] timeout A num ...

  • Technicolor - Thomson ST536 - page 207

    E-DOC-CTC-20061 027-0003 v2.0 DNS Commands 185 dns client dnsadd Add a DNS server . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dns client dnsadd addr = <string> [port = <number>] addr The IP addre ss of the DNS server to be adde d. REQUIRED port The DNS server port number . The default is 53 . OP TIONAL =>dns client dnsadd addr=150. ...

  • Technicolor - Thomson ST536 - page 208

    E-DOC-CTC- 20061027-0003 v2 .0 DNS Commands 186 dns client dnsdelete Delete a DNS server . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dns client dnsdelete index = <number{1-99}> index A numb er between 1 and 99. Represents the index number of the DNS server to be deleted. Ti p Use the command :dns cl ient dnslist to obtain a list of DNS serv ...

  • Technicolor - Thomson ST536 - page 209

    E-DOC-CTC-20061 027-0003 v2.0 DNS Commands 187 dns client dnslist List all DNS servers. SYNT AX: EXAMPLE: RELA TED COMMANDS: dns client dnslist =>dns client dnslist Entry State Family Server 1 CONNECTED IP [port] 53 - [addr] 127.0.0.1 2 CONNECTED IP [port] 53 - [addr] 150.150.150.150 => dns client dnsadd Add a DNS server . dns client dnsdelet ...

  • Technicolor - Thomson ST536 - page 210

    E-DOC-CTC- 20061027-0003 v2 .0 DNS Commands 188 dns client flush Remove all DNS servers. SYNT AX: dns client flush ...

  • Technicolor - Thomson ST536 - page 211

    E-DOC-CTC-20061 027-0003 v2.0 DNS Commands 189 dns client nslookup DNS lookup for a dom ain name or an addre ss. SYNT AX: where: dns client nslookup host = <string> host T he DNS domain name string for which to query . REQUIRED ...

  • Technicolor - Thomson ST536 - page 212

    E-DOC-CTC- 20061027-0003 v2 .0 DNS Commands 190 dns server config Modify the DNS resolver confi guration. SYNT AX: where: EXAMPLE: dns server config [domain = <string>] [timeout = <number{0-2147483647}>] [suppress = <number>] [state = <{disabled | enabled}>] [trace = <{disabled | enabled}>] [WANDownSpoofing = <{disa ...

  • Technicolor - Thomson ST536 - page 213

    E-DOC-CTC-20061 027-0003 v2.0 DNS Commands 191 dns server flush Flush all local DN S hosts and routes. SYNT AX: dns server flush ...

  • Technicolor - Thomson ST536 - page 214

    E-DOC-CTC- 20061027-0003 v2 .0 DNS Commands 192 dns server debug clear Clear the DNS server/f orwarder statistics. SYNT AX: EXAMPLE: RELA TED COMMANDS: dns server debug clear =>dns server debug stats Corrupted packets received : 100 Local questions resolved : 3 Local negative answers sent : 1 Total DNS packets forwarded : 0 External answers rece ...

  • Technicolor - Thomson ST536 - page 215

    E-DOC-CTC-20061 027-0003 v2.0 DNS Commands 193 dns server debug stats Print the DNS server/f orwarder statistics. SYNT AX: EXAMPLE: RELA TED COMMANDS: dns server debug stats =>dns server debug stats Corrupted packets received : 100 Local questions resolved : 3 Local negative answers sent : 1 Total DNS packets forwarded : 0 External answers recei ...

  • Technicolor - Thomson ST536 - page 216

    E-DOC-CTC- 20061027-0003 v2 .0 DNS Commands 194 dns server debug spoof clear Clear the intercept cache table SYNT AX: RELA TED COMMANDS: dns server debug spoof clear dns server debug spoof getaddress Get the real ip for the given spoofed ip dns server debug spoo f getflags Get the error flags fo r the given spoofed ip dns server debu g spoof list L ...

  • Technicolor - Thomson ST536 - page 217

    E-DOC-CTC-20061 027-0003 v2.0 DNS Commands 195 dns server debug spoof getaddress Get the real ip for the given spoofed ip SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dns server debug spoof getaddress addr = <ip-address> addr The IP ad dress of the spoofed server . REQUIRED {Administrator}=>dns server debug spoof getaddress addr=198.18.1.1 ...

  • Technicolor - Thomson ST536 - page 218

    E-DOC-CTC- 20061027-0003 v2 .0 DNS Commands 196 dns server debug spoof getflags Get the error flags for the given spoofed ip SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dns server debug spoof getflags addr = <ip-address> addr The IP ad dress of the spoofed server . REQUIRED {Administrator}[dns server debug spoof]=>:dns server debug spoof g ...

  • Technicolor - Thomson ST536 - page 219

    E-DOC-CTC-20061 027-0003 v2.0 DNS Commands 197 dns server debug spoof list List the intercept cache table. SYNT AX: EXAMPLE: RELA TED COMMANDS: dsn server debug spoof list {Administrator}[dns server debug spoof]=>list Spoof IP FQDN Real IP Flags 198.18.1.1 eu.thmulti.com 0.0.0.0 Not resolved 198.18.1.2 thmulti.com 0.0.0.0 Not resolved 198.18.1.3 ...

  • Technicolor - Thomson ST536 - page 220

    E-DOC-CTC- 20061027-0003 v2 .0 DNS Commands 198 dns server debug spoof update Update the interc ept cache table. SYNT AX: EXAMPLE: RELA TED COMMANDS: dns server debug spoof update {Administrator}=>dns server debug spoof update {Administrator}=> dns server debug spoo f clear Clear the intercept cache table dns server debug spoof getaddress Get ...

  • Technicolor - Thomson ST536 - page 221

    E-DOC-CTC-20061 027-0003 v2.0 DNS Commands 199 dns server host add Add a local DNS host. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dns server host add name = <string> [addr = <ip-address>] [ttl = <number{0-2147483647}>] name The name of the IP host to be added. REQUIRED addr The I P address of the host. OP TIONAL ttl A number be ...

  • Technicolor - Thomson ST536 - page 222

    E-DOC-CTC- 20061027-0003 v2 .0 DNS Commands 200 dns server host delete Delete a local DNS host. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dns server host delete name = <string> name The name of the DNS host to be del eted. REQUIRED =>dns server host list Address Hostname TTL (s) 150.150.150.150 myDNS 3600 <local> speedtouch 0 <l ...

  • Technicolor - Thomson ST536 - page 223

    E-DOC-CTC-20061 027-0003 v2.0 DNS Commands 201 dns server host flush Flush all the local DNS hosts. SYNT AX: EXAMPLE: dns server host flush =>dns server host list Address Hostname TTL (s) 192.168.1.64 * Unknown-00-10-a4-ad-32-cf 60 <local> dsldevice 1200 <local> speedtouch 1200 =>dns server host flush =>dns server host list =&g ...

  • Technicolor - Thomson ST536 - page 224

    E-DOC-CTC- 20061027-0003 v2 .0 DNS Commands 202 dns server host list List all the local DNS hosts. SYNT AX: EXAMPLE: RELA TED COMMANDS: dns server host list =>dns server host list Address Hostname TTL (s) 192.168.1.64 * Unknown-00-10-a4-ad-32-cf 60 <local> dsldevice 1200 <local> speedtouch 1200 => dns server host add Add a local D ...

  • Technicolor - Thomson ST536 - page 225

    E-DOC-CTC-20061 027-0003 v2.0 DNS Commands 203 dns server route add Creates a DNS forwarding entry or template. SYNT AX: where: dns server route add dns = <ip-address> [src = <ip-address>] [srcmask = <ip-mask(dotted or cidr)>] [domain = <string>] [metric = <number{0-100}>] [intf = <string>] dns The IP address of ...

  • Technicolor - Thomson ST536 - page 226

    E-DOC-CTC- 20061027-0003 v2 .0 DNS Commands 204 EXAMPLE: RELA TED COMMANDS: =>dns server route add dns=150.150.150.150 src=10.0.0.0/8 domain=myDNS intf=eth0 =>dns server route list DNS Server Source Domain Metric Intf State 150.150.150.150 10.0.0.0/8 myDNS 0 eth0 UP => dns server route delete Delete a DNS forwarding route. dns server route ...

  • Technicolor - Thomson ST536 - page 227

    E-DOC-CTC-20061 027-0003 v2.0 DNS Commands 205 dns server route delete Deletes a DNS forwa rdi ng entry or template SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dns server route delete dns = <ip-address> [domain = <string>] [intf = <{loop|Internet|LocalNetwork}>] dns The IP address of the DNS server for which the forwar ding route ...

  • Technicolor - Thomson ST536 - page 228

    E-DOC-CTC- 20061027-0003 v2 .0 DNS Commands 206 dns server route flush Removes all DNS forwarding entries and templates. SYNT AX: EXAMPLE: dns server route flush =>dns server route list DNS Server Source Domain Metric Intf State 150.150.150.150 10.0.0.0/8 myDNS 0 eth0 UP =>dns server route flush =>dns server route list => ...

  • Technicolor - Thomson ST536 - page 229

    E-DOC-CTC-20061 027-0003 v2.0 DNS Commands 207 dns server route list List all the DNS forwardi ng entries or templates. SYNT AX: EXAMPLE: RELA TED COMMANDS: dns server route list =>dns server route list DNS Server Source Domain Metric Intf State 150.150.150.150 10.0.0.0/8 myDNS 0 eth0 UP => dns server route add Adds a DNS forwarding route. dn ...

  • Technicolor - Thomson ST536 - page 230

    E-DOC-CTC- 20061027-0003 v2 .0 DNS Commands 208 ...

  • Technicolor - Thomson ST536 - page 231

    E-DOC-CTC-20061 027-0003 v2.0 DSD Commands 209 11 DSD Commands Introduction This chapter describes the commands of the dsd comman d group. Contents This chapter covers th e following commands: dsd config Display/modify the Differentia ted Service Delivery (DSD) framework configuration. 210 dsd debug con fig Display/modify DSD debug settings 211 dsd ...

  • Technicolor - Thomson ST536 - page 232

    E-DOC-CTC- 20061027-0003 v2 .0 DSD Commands 210 dsd config Display/modify the Diffe ren tiated Service Deliver y (DSD) framework configuration. SYNT AX: where: EXAMPLE: dsd config [state = <{disabled | enabled | automatic}>] state Choose between: > automatic (default): By default (DSD config state is automatic), the DSD framework is not ac ...

  • Technicolor - Thomson ST536 - page 233

    E-DOC-CTC-20061 027-0003 v2.0 DSD Commands 211 dsd debug config Display/modif y DSD debug settings SYNT AX: where: config [turbomode = <{disabled|enabled}>] turbomode Enable/disable turbom ode OP TIONAL ...

  • Technicolor - Thomson ST536 - page 234

    E-DOC-CTC- 20061027-0003 v2 .0 DSD Commands 212 dsd debug connection list Display the internal co nnection pool usage. SYNT AX: where: dsd debug connection list [expand = <{disabled|enabled}>] expand Enable or disable the expanded listing. The default is disab led . optional ...

  • Technicolor - Thomson ST536 - page 235

    E-DOC-CTC-20061 027-0003 v2.0 DSD Commands 213 dsd debug proxy Display/modi fy the HyperT ext T ransfer Proto col (HTTP) Intercep t fixed proxy configu ration. SYNT AX: where: EXAMPLE: dsd debug proxy [state = <{disabled | enabled}>] [dest = <ip-address>] [port = <{supported TCP/UDP port} or number>] state Enable or disable fixed ...

  • Technicolor - Thomson ST536 - page 236

    E-DOC-CTC- 20061027-0003 v2 .0 DSD Commands 214 dsd debug recycling Display/ modify HTTP I recycling settings SYNT AX: where: dsd debug recycling state = <disabled>|<enabled> interval = <number> httpidle = <number> otheridle = <number> state Enable/disable str eam recycling OPTIONAL interval T ime between successi ve a ...

  • Technicolor - Thomson ST536 - page 237

    E-DOC-CTC-20061 027-0003 v2.0 DSD Commands 215 dsd debug stats Display/clear DSD framework and module statistics SYNT AX: where: dsd debug stats name = <{intercept|urlfilter|recycling|syslog|all} clear = <{no|yes}> name Specify the name of a module REQUIRED clear Clear the specif ied statistics REQUI RED ...

  • Technicolor - Thomson ST536 - page 238

    E-DOC-CTC- 20061027-0003 v2 .0 DSD Commands 216 dsd intercept config Display/modify the HTTP Intercept configuration. SYNT AX: where: EXAMPLE: dsd intercept config [WDSpoofedIP = <ip-address>] [servertimeout = <number>] [servererrorurl = <string>] [categoryerrorurl = <string>] [monitorintercepturl = <string>] [urlblock ...

  • Technicolor - Thomson ST536 - page 239

    E-DOC-CTC-20061 027-0003 v2.0 DSD Commands 217 dsd sy slog config Display/modif y the HTTP Intercept logg ing configurat ion. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dsd syslog config [syslog = <{none | unauthorized | errors | inter- cepted | all}>] syslog Define the type of events to log. Choose between: > none : nothing is logged to ...

  • Technicolor - Thomson ST536 - page 240

    E-DOC-CTC- 20061027-0003 v2 .0 DSD Commands 218 dsd sy slog list Display the HTTP Intercept log file. SYNT AX: EXAMPLE: RELA TED COMMANDS: dsd syslog list =>dsd syslog list <86> SysUpTime: 00:22:37 [HTTPI] src=10.0.0.1 src_port=1965 dst=141.11.196.35 dst_port=80 eve nt=ServerConnect dst_name=aWebsite.com/icons/Button_Document.gif <86> ...

  • Technicolor - Thomson ST536 - page 241

    E-DOC-CTC-20061 027-0003 v2.0 DSD Commands 219 dsd urlfilter config Display/modify the URL filtering configuration. SYNT AX: where: EXAMPLE: dsd urlfilter config [state = <{disabled | enabled}>] [blockproxy = <{disabled | enabled}>] [blockipaddress = <{disabled | enabled}>] [blockobscuredip = <{disabled | enabled}>] [default ...

  • Technicolor - Thomson ST536 - page 242

    E-DOC-CTC- 20061027-0003 v2 .0 DSD Commands 220 dsd urlfilter rule add Add a rule. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dsd urlfilter rule add url = <string> action = <{block | accept | redirect}> redirect = <string> url Definition of the URL filter . REQUIRED action The action to perform when URL matches URL. Choose betwee ...

  • Technicolor - Thomson ST536 - page 243

    E-DOC-CTC-20061 027-0003 v2.0 DSD Commands 221 dsd urlfilter rule delete Delete a rule. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dsd urlfilter rule delete index = <number> [url = <string>] index Insertion po sition in the list. Ti p Use the command :dsd urlfilter rule list to obtain the index number of the rule to be deleted. REQUIRE ...

  • Technicolor - Thomson ST536 - page 244

    E-DOC-CTC- 20061027-0003 v2 .0 DSD Commands 222 dsd urlfilter rule flush Remove all current rules. SYNT AX: EXAMPLE: dsd urlfilter rule flush =>dsd urlfilter rule list Index Action Url Redirect ----- ------ --- -------- 0 redirect www.speedtouch.com www.speedtouch.be 1 accept www.baen.com Rule list statistics : 2 present, 128 total (0.0% used) = ...

  • Technicolor - Thomson ST536 - page 245

    E-DOC-CTC-20061 027-0003 v2.0 DSD Commands 223 dsd urlfilter rule list Display the list of curr ent rules. SYNT AX: EXAMPLE: RELA TED COMMANDS: dsd urlfilter rule list =>dsd urlfilter rule list Index Action Url Redirect ----- ------ --- -------- 0 redirect www.speedtouch.com www.speedtouch.be 1 accept www.baen.com Rule list statistics : 2 presen ...

  • Technicolor - Thomson ST536 - page 246

    E-DOC-CTC- 20061027-0003 v2 .0 DSD Commands 224 dsd urlfilter rule modify Modify an existing rule. SYNT AX: where: dsd urlfilter rule modify index = <number> [newurl = <string>] action = <{block | accept | redirect}> redirect = <string> index Insertion po sition in the list. REQUIRED newurl Definition of the new URL filter . ...

  • Technicolor - Thomson ST536 - page 247

    E-DOC-CTC-20061 027-0003 v2.0 DSD Commands 225 EXAMPLE: RELA TED COMMANDS: =>dsd urlfilter rule list Index Action Url Redirect ----- ------ --- -------- 0 redirect www.speedtouch.com www.speedtouch.be 1 accept www.baen.com Rule list statistics : 2 present, 128 total (0.0% used) =>dsd urlfilter rule modify index=0 newurl=www.speed*.* action=re ...

  • Technicolor - Thomson ST536 - page 248

    E-DOC-CTC- 20061027-0003 v2 .0 DSD Commands 226 ...

  • Technicolor - Thomson ST536 - page 249

    E-DOC-CTC-20061 027-0003 v2.0 DynDNS Commands 227 12 DynDNS Commands Introduction Dynamic DNS is a service that allows to bind a ho st name to an IP address. In contra st to classica l DN S, this service allows regular updates of the IP address related to a host name. In this wa y , hosts of which the IP address regularly changes (for exam ple due ...

  • Technicolor - Thomson ST536 - page 250

    E-DOC-CTC- 20061027-0003 v2 .0 DynDNS Commands 228 dyndns add Add a dynamic DNS client. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dyndns add name = <string> name The name of the new dynamic DNS client. Note A maximum of 5 clients ca n be configured. REQUIRED =>dyndns add name=WAN =>dyndns list WAN : [INIT] user = password = addr = 0.0 ...

  • Technicolor - Thomson ST536 - page 251

    E-DOC-CTC-20061 027-0003 v2.0 DynDNS Commands 229 dyndns delete Delete a dynamic DNS client. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dyndns delete name = <string> name The name of the dynamic DNS client to be dele ted. REQUIRED =>dyndns list WAN : [INIT] user = password = addr = 0.0.0.0 =>dyndns delete name=WAN =>dyndns list => ...

  • Technicolor - Thomson ST536 - page 252

    E-DOC-CTC- 20061027-0003 v2 .0 DynDNS Commands 230 dyndns flush Delete all the dy namic DNS clients. SYNT AX: dyndns flush ...

  • Technicolor - Thomson ST536 - page 253

    E-DOC-CTC-20061 027-0003 v2.0 DynDNS Commands 231 dyndns list List all the dyna mic DNS clients. SYNT AX: EXAMPLE: RELA TED COMMANDS: dyndns list =>dyndns list WAN : [INIT] user = password = addr = 0.0.0.0 => dyndns add Add a dynamic DNS client. dyndns delete Delete a dynamic DNS client. ...

  • Technicolor - Thomson ST536 - page 254

    E-DOC-CTC- 20061027-0003 v2 .0 DynDNS Commands 232 dyndns modify Modify a dynamic DNS client. SYNT AX: where: dyndns modify name = <string> [intf = <string>] [user = <string>] [password = <password>] [group = <string>] [mx = <string>] [backmx = <{disabled | enabled}>] [wildcard = <{disabled | enabled}> ...

  • Technicolor - Thomson ST536 - page 255

    E-DOC-CTC-20061 027-0003 v2.0 DynDNS Commands 233 EXAMPLE: status Enable or disabl e the dynamic DNS client. The default is disab led . OPTIONAL trace Enable or disable the verbose console logg ing for the dynamic DNS client. The default is disab led . OPTIONAL =>dyndns list WAN : [INIT] user = password = addr = 0.0.0.0 =>dyndns modify name=W ...

  • Technicolor - Thomson ST536 - page 256

    E-DOC-CTC- 20061027-0003 v2 .0 DynDNS Commands 234 dyndns host add Add a fully qualified host name. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dyndns host add group = <string> name = <string> group The dynamic DNS host grou p. Note A maximum of 4 diffe rent groups can be created. REQUIRED name The name of an IP host to add. Note A maxi ...

  • Technicolor - Thomson ST536 - page 257

    E-DOC-CTC-20061 027-0003 v2.0 DynDNS Commands 235 dyndns host delete Delete a hos t name. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dyndns host delete name = <string> name The name of the IP host to be deleted. REQU IRED =>dyndns host list local : [ ] localhost.com public : [ ] publichost.com legend : [ ] not initialised [o] update in pr ...

  • Technicolor - Thomson ST536 - page 258

    E-DOC-CTC- 20061027-0003 v2 .0 DynDNS Commands 236 dyndns host flush Delete all hosts. SYNT AX: i The hosts cannot be flushed, if there is still a group referenced to the hosts. dyndns host flush ...

  • Technicolor - Thomson ST536 - page 259

    E-DOC-CTC-20061 027-0003 v2.0 DynDNS Commands 237 dyndns host list List all host names. SYNT AX: EXAMPLE: RELA TED COMMANDS: dyndns host list =>dyndns host list local : [ ] localhost.com public : [ ] publichost.com legend : [ ] not initialised [o] update in progress [v] update successful [x] error => dyndns host ad d Add a ful ly qualified ho ...

  • Technicolor - Thomson ST536 - page 260

    E-DOC-CTC- 20061027-0003 v2 .0 DynDNS Commands 238 dyndns service list List all dynami c DNS services. SYNT AX: EXAMPLE: dyndns service list =>dyndns service list dyndns : server = members.dyndns.org port = 80 request = /nic/update update interval = 2097120 retry interval = 30 max retry = 3 statdns : server = members.dyndns.org port = 80 request ...

  • Technicolor - Thomson ST536 - page 261

    E-DOC-CTC-20061 027-0003 v2.0 DynDNS Commands 239 RELA TED COMMANDS: dyndns service modify Modify specific dynamic DNS service settings. ...

  • Technicolor - Thomson ST536 - page 262

    E-DOC-CTC- 20061027-0003 v2 .0 DynDNS Commands 240 dyndns service modify Modify specific dynami c DNS service settings. SYNT AX: where: dyndns service modify name = <string> [server = <string>] [port = <{supported TCP/UDP port name} or number>] [request = <string>] [updateinterval = <number{0-2097120}>] [retryinterval ...

  • Technicolor - Thomson ST536 - page 263

    E-DOC-CTC-20061 027-0003 v2.0 DynDNS Commands 241 EXAMPLE: RELA TED COMMANDS: =>dyndns service modify name=custom server=mydyndns.org port=www-http request=hereiam | updateinterval=2000000 retryinterval=15 max_retry=5 =>dyndns service list dyndns : server = members.dyndns.org port = 80 request = /nic/update update interval = 2097120 retry int ...

  • Technicolor - Thomson ST536 - page 264

    E-DOC-CTC- 20061027-0003 v2 .0 DynDNS Commands 242 ...

  • Technicolor - Thomson ST536 - page 265

    E-DOC-CTC-20061 027-0003 v2.0 Env Commands 243 13 Env Commands Introduction This chapter describes the commands of the env comman d group. Contents This chapter covers th e following commands: env flush Flush all the non-system e nvironment variables. 244 env get Get the current value of an environment variable. 245 env list S how all the currently ...

  • Technicolor - Thomson ST536 - page 266

    Env Commands E-DOC-CTC- 20061027-0003 v2 .0 244 env flush Flush all the non-system environment variables. SYNT AX: env flush ...

  • Technicolor - Thomson ST536 - page 267

    Env Commands E-DOC-CTC-20061 027-0003 v2.0 245 env get Get the current value of an environment variable. SYNT AX: where: RELA TED COMMANDS: env get var = <string> var The name of th e environme nt variable. Ti p Use th e command :env list to obtain a list of all environ- ment variables. REQUIRED env list List all current env ironment variable ...

  • Technicolor - Thomson ST536 - page 268

    E-DOC-CTC- 20061027-0003 v2 .0 Env Commands 246 env list Show all the currently availa ble environment variables. SYNT AX: RELA TED COMMANDS: env list env get Get the current value of an environment variable. ...

  • Technicolor - Thomson ST536 - page 269

    E-DOC-CTC-20061 027-0003 v2.0 Env Commands 247 env set Set an environment variable. SYNT AX: where: EXAMPLE: For infinite TELN ET time out, set the val ue of the variable SESSIONTIMEOUT to “0”: RELA TED COMMANDS: env set var = <string> value = <translated string> var The name of th e environme nt variable. Ti p When creating an envi ...

  • Technicolor - Thomson ST536 - page 270

    E-DOC-CTC- 20061027-0003 v2 .0 Env Commands 248 env unset Delete a environment variable. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: env unset var = <string> var The name of the environment variable to be deleted. Note System variables (built-in variabl es with names starting with an underscore “_”, “CONF” or “HOST”) cannot be uns ...

  • Technicolor - Thomson ST536 - page 271

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 249 14 Eth Commands Introduction This chapter describes the commands of the eth comman d group. Contents This chapter covers th e following commands: eth ifadd Create a new ETH interfac e. 252 eth ifattach Attach an E TH interface. 253 eth ifconfig Modify an ETH interface. 254 eth ifdelete Dele te an ETH i ...

  • Technicolor - Thomson ST536 - page 272

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 250 eth bridge igmpsnooping ifconfi g Configure the brid ge interface‘s IGMP snoopi ng flags and mode 282 eth bridge igmpsnooping iflist Display a bridge inter face‘s IGMP s tatus 283 eth bridge igmpsnooping clear Clear the snooping statistics 284 eth bridge macadd Add a static MAC address to a br idg ...

  • Technicolor - Thomson ST536 - page 273

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 251 eth vlan flush Flush all VLANs. 325 eth vlan list Display all VLAN s. 326 ...

  • Technicolor - Thomson ST536 - page 274

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 252 eth ifadd Create a new ETH interface. SYNT AX: where: RELA TED COMMANDS: eth ifadd intf = <string> intf The name of the new ETH in terface. REQUIRED eth ifdelete Delete an ETH interface. eth iflist Display the ETH interfaces . ...

  • Technicolor - Thomson ST536 - page 275

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 253 eth ifattach Attach an ETH interf ace. SYNT AX: where: RELA TED COMMANDS: eth ifattach intf = <string> intf The name of the ETH interf ace to be attached. REQUIRED eth ifdetach Detach an ETH interface. ...

  • Technicolor - Thomson ST536 - page 276

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 254 eth ifconfig Modify an ETH interfac e. SYNT AX: where: eth ifconfig intf = <string> [dest = <string>] [retry = <number{0-65535}>] [vlan = <string>] intf The name of the ETH interface to be con figured. REQUIRE D dest The destination interface fo r this ETH interface. OPTIONAL r ...

  • Technicolor - Thomson ST536 - page 277

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 255 eth ifdelete Delete an ETH interface. SYNT AX: where: RELA TED COMMANDS: eth ifdelete intf = <string> intf The name of the ETH interface name to be d eleted. REQUIRED eth ifadd Create a new ETH interface. eth iflist Display the ETH interfaces . ...

  • Technicolor - Thomson ST536 - page 278

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 256 eth ifdetach Detach an ETH interface. SYNT AX: where: RELA TED COMMANDS: eth ifdetach intf = <string> intf The name of the ETH interf ace to be detached. REQUIRED eth ifattach Attach an ETH interface. ...

  • Technicolor - Thomson ST536 - page 279

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 257 eth iflist Display the ETH interfaces. SYNT AX: where: RELA TED COMMANDS: eth iflist [intf = <string>] [string = <string>] [beginstring = <string>] intf The name of the ETH in terface to be displayed. Note If not specified, all the ETH interfaces will be displayed. OP TIONAL string St ...

  • Technicolor - Thomson ST536 - page 280

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 258 eth flush Flush all the ETH interfaces. SYNT AX: i The flush command does not impact previo usly saved configurations. eth flush ...

  • Technicolor - Thomson ST536 - page 281

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 259 eth bridge clear Clear the bridge statistics. SYNT AX: eth bridge clear ...

  • Technicolor - Thomson ST536 - page 282

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 260 eth bridge list Display the current bridge instances Syntax where eth bridge list [brname = <{brid ge}>] [string = <string>] [beginstring = <string>] brname The name of a bridge i nstance OPTIONAL string String matching condit ion OPTI ONAL beginstring Beginstring matching condition ...

  • Technicolor - Thomson ST536 - page 283

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 261 eth bridge add Add a new bridge instance Syntax where eth bridge add brname=<string> brname The na me of the new bridge instance REQUIRED ...

  • Technicolor - Thomson ST536 - page 284

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 262 eth bridge delete Delete a bridge instance Syntax where eth bridge delete brname = <{bridge}> brname The name of the brid ge instance to be deleted REQUIRED ...

  • Technicolor - Thomson ST536 - page 285

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 263 eth bridge select Select the default bridge to configure interfaces (when not sett ing a bridge name, for legacy purposes). Syntax where eth bridge select brname = <{bridge}> brname The na me of a bridge instance REQ UIRED ...

  • Technicolor - Thomson ST536 - page 286

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 264 eth bridge config Modify/display the brid ge configuration setting s. SYNT AX: where: eth bridge config [brname = <{bridge}>] [age = <number{10-100000}>] [filter = <{no_WAN_broadcast | none}>] [vlan = <{disabled | enabled}>] [precedencemap = <string>] brname The name of a ...

  • Technicolor - Thomson ST536 - page 287

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 265 eth bridge dynvlan actlist Display the active MAC entries fo r the dynamic VL AN membership. SYNT AX: RELA TED COMMANDS: eth bridge dynvlan actlist eth bridge dynvlan add Add a dynamic VLAN membership entry . eth bridge dynvlan c onfig Modify the dynamic VLAN me mbership configu ration. eth bridge dynv ...

  • Technicolor - Thomson ST536 - page 288

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 266 eth bridge dynvlan add Add a dynamic VLAN membership entry . SYNT AX: where: RELA TED COMMANDS: eth bridge dynvlan add [id = <number{0-100000}>] hwaddr = <masked-hardware-address> vlan = <string> [remvlan = <{default}>] id A number between 0 and 100000. Represents the id of the ...

  • Technicolor - Thomson ST536 - page 289

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 267 eth bridge dynvlan config Modify the d ynamic VLAN membe rship configurati on. SYNT AX: where: RELA TED COMMANDS: eth bridge dynvlan config [timeout = <number{0-100000}>] timeout A numb er betwee n 0 and 100000 (seconds). Represents timeout fo r the dynami c entries. OP TIONAL eth bridge dynvlan ...

  • Technicolor - Thomson ST536 - page 290

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 268 eth bridge dynvlan delete Delete a dynamic VLAN membership entry . SYNT AX: where: RELA TED COMMANDS: eth bridge dynvlan delete id = <number{0-100000}> id A number between 0 and 100000. Represents the id of a dynamic VLAN membership. REQUIRED eth bridge dynvlan actlist Display the active MAC ent ...

  • Technicolor - Thomson ST536 - page 291

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 269 eth bridge dynvlan flush Flush all dyna mic VLAN membership entries. SYNT AX: eth bridge dynvlan flush ...

  • Technicolor - Thomson ST536 - page 292

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 270 eth bridge dynvlan list Display a dynamic VLAN membership entry . SYNT AX: RELA TED COMMANDS: eth bridge dynvlan list eth bridge dynvlan actlist Display the active MAC entries fo r the dyna mic VL AN me mbership. eth bridge dynvlan add Add a dynamic VLAN membership entry . eth bridge dynvlan c onfig M ...

  • Technicolor - Thomson ST536 - page 293

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 271 eth bridge flush Flush bridge interfaces and parameters. SYNT AX: i The flush comman d does not impact previously saved configurations. eth bridge flush ...

  • Technicolor - Thomson ST536 - page 294

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 272 eth bridge ifadd Add a new bridge interface. SYNT AX: where: RELA TED COMMANDS: eth bridge ifadd [brname = <{brid ge}>] intf = <string> brname The na me of a bridge instan ce. OPTIONAL intf The name of the new br idge interface. REQUIRED eth bridge ifdelete Delete a bridg e interface. eth ...

  • Technicolor - Thomson ST536 - page 295

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 273 eth bridge ifattach Attach a bridge interface. SYNT AX: where: RELA TED COMMANDS: eth bridge ifattach [brname = <{bridge}>] intf = <string> brname The na me of a bridge instan ce. OPTIONAL intf The name of the bridge interface to b e attached. REQUIRED eth bridge ifdetach Detach a bridge in ...

  • Technicolor - Thomson ST536 - page 296

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 274 eth bridge ifconfig Modify a bridge interface configuratio n. SYNT AX: where: eth bridge ifconfig [brname = <{bridge}>] intf = <string> [dest = <string>] [portstate = <{disabled | learning | forwarding}>] [retry = <number{0-65535}>] [prioconfig = <{disabled|over- write ...

  • Technicolor - Thomson ST536 - page 297

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 275 ipprec The IP precedence for this interface. Choose between: > disabled > preceden ce > dscp. The default is disab led . OP TIONAL priority A number between 0 and 7. Represents the default priori ty for tagging egress packe ts. The default is 0 . OP TIONAL regenprio The pr iority regeneration ...

  • Technicolor - Thomson ST536 - page 298

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 276 eth bridge ifdelete Delete a bridge interface. SYNT AX: where: RELA TED COMMANDS: eth bridge ifdelete [brname = <{bridge}>] intf = <string> brname The na me of a bridge instan ce. OPTIONAL intf The name of the bridge interf ace na me to be deleted. REQUIRED eth bridge ifadd Add a new bridg ...

  • Technicolor - Thomson ST536 - page 299

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 277 eth bridge ifdetach Detach a bridge interface. SYNT AX: where: RELA TED COMMANDS: eth bridge ifdetach [brname = <{bridge}>] intf = <string> brname The na me of a bridge instan ce. OPTIONAL intf The name of the bridge interface to b e detached. REQUIRED eth bridge ifattach At tach a bridge i ...

  • Technicolor - Thomson ST536 - page 300

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 278 eth bridge iflist Display the current bridge interfaces. SYNT AX: where: RELA TED COMMANDS: eth bridge iflist [brname = <{bridge}>] [intf = <string>] [string = <string>] [beginstring = <string>] brname The na me of a bridge instan ce. OPTIONAL intf The name of the bridge interf ...

  • Technicolor - Thomson ST536 - page 301

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 279 eth bridge ifflush Flush the br idge interfac es: detach/delete all interfa ces. SYNT AX: where: eth bridge ifflush [brname = <{bridge}>] brname The na me of a bridge instan ce. OPTIONAL ...

  • Technicolor - Thomson ST536 - page 302

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 280 eth bridge igmpsnooping config Configure the bridge instance‘ s IGMP Snooping flag s Syntax where: eth bridge igmpsnooping config [brname = <{bridge}>] [state = <{enabled|disabled}>] [floodrp = <{disabled|enabled}>] [floodmcast = <{disabled|enabled}>] brname The name of a bri ...

  • Technicolor - Thomson ST536 - page 303

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 281 eth bridge igmpsnooping list Display a brid ge instance‘s snooped group s. Syntax where: eth bridge igmpsnooping list [brname = <{bridge}>] brname The name of a bridge i nstance OPTIONAL ...

  • Technicolor - Thomson ST536 - page 304

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 282 eth bridge igmpsnooping ifconfig Configure the bridge in terface‘s IGMP snoopi ng flags and mode. Syntax where: eth bridge igmpsnooping ifconfig [brname = <{bridge}>] intf = <{interface}> [portmode = <{Host|Router|Auto}>] [fastleave = <{disabled|enabled}>] [exptrack = <{di ...

  • Technicolor - Thomson ST536 - page 305

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 283 eth bridge igmpsnooping iflist Display a bridge i nterface‘s IGMP status Syntax where: Display bridge interface IGMP status [brname = <{bridge}>] [intf = <{interface}>] brname The name of a bridge i nstance OPTIONAL intf The name of the bridge interface OP TIONAL ...

  • Technicolor - Thomson ST536 - page 306

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 284 eth bridge igmpsnooping clear Clear the snooping statistics. Syntax where: eth bridge igmpsnooping clear [brname = <{bridge}>] [intf = <{interface}>] brname The name of a bridge i nstance OPTIONAL intf The name of the bridge interface OP TIONAL ...

  • Technicolor - Thomson ST536 - page 307

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 285 eth bridge macadd Add a static MAC address to a bridge interface. This command allows to manually add static MA C addresses, which should normally be dynamically discovered by the bridge itself. SYNT AX: where: eth bridge macadd [brname = <{bridge}>] intf = <string> hwaddr = <hardware-ad ...

  • Technicolor - Thomson ST536 - page 308

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 286 EXAMPLE: RELA TED COMMANDS: =>eth bridge maclist 00:10:a4:ad:32:cf -- dynamic, ethport1, 300 seconds 00:90:d0:8b:fc:2c -- permanent 01:00:5e:00:00:67 -- static 01:00:5e:7f:ff:fa -- static 01:80:c2:00:00:00 -- permanent 01:80:c2:00:00:01 -- permanent 01:80:c2:00:00:02 -- permanent 01:80:c2:00:00:03 ...

  • Technicolor - Thomson ST536 - page 309

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 287 eth bridge macdelete Remove a MAC address from th e filtering database. SYNT AX: where: EXAMPLE: eth bridge macdelete [brname = <{bridge}>] hwaddr = <hardware-address> [vlan = <string>] brname The na me of a bridge instan ce. OPTIONAL hwaddr The Ethernet MAC address of the entry to be ...

  • Technicolor - Thomson ST536 - page 310

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 288 RELA TED COMMANDS: eth bridge macadd Add a static MAC address to a bridge interface. eth bridge maclist Display the MAC address database. ...

  • Technicolor - Thomson ST536 - page 311

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 289 eth bridge maclist Display the MAC address database. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: eth bridge maclist [brname = <{bridge}>] brname The na me of a bridge instan ce. OPTIONAL =>eth bridge maclist 00:0d:9d:47:dd:aa -- dynamic, ethport1, 300 seconds 00:90:d0:72:88:64 -- permanent 01: ...

  • Technicolor - Thomson ST536 - page 312

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 290 eth bridge mcdadd Add a multicast group to be dropped to the database. SYNT AX: where: RELA TED COMMANDS: eth bridge mcdadd [brname = <{bridge}>] srcintfs = <string or combination of strings separated by '+'}> dstintfs = <string or combination of strings separated by '+&a ...

  • Technicolor - Thomson ST536 - page 313

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 291 eth bridge mcddelete Delete a multic ast group to be dropped from the database. SYNT AX: where: RELA TED COMMANDS: eth bridge mcddelete [brname = <{bridge}>] brname The na me of a bridge instan ce. OPTIONAL eth bridge mcdadd Add a multicast group to be dropped to the database. eth bridge mcdlist ...

  • Technicolor - Thomson ST536 - page 314

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 292 eth bridge mcdlist Display the multic ast group to be droppe d from the database. SYNT AX: RELA TED COMMANDS: eth bridge mcdlist eth bridge mcdadd Add a multicast group to be dropped to the database. eth bridge mcddelete Del ete a multicast group to be drop ped from the database. ...

  • Technicolor - Thomson ST536 - page 315

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 293 eth bridge rule add Add a new constraint to th e VLAN learning system. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: eth bridge rule add type = <{shared | independent}> vlan = <string> [vlan2 = <string>] [isi = <number{0-32}>] type T y pe of constraint. Choose between: > shared ...

  • Technicolor - Thomson ST536 - page 316

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 294 eth bridge rule delete Delete a constraint from the VLAN learning system. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: eth bridge rule delete index = <number{0-32}> index Index of the constrain t to be dele ted. Ti p Use the command :eth bridge rule list to obtain a list of the in dexes of the co ...

  • Technicolor - Thomson ST536 - page 317

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 295 eth bridge rule flush Flush all constraints from the VLAN learning system. SYNT AX: eth bridge rule flush ...

  • Technicolor - Thomson ST536 - page 318

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 296 eth bridge rule list Display all constraints from the VLAN lear ning system. SYNT AX: EXAMPLE: RELA TED COMMANDS: eth bridge rule list =>eth bridge rule list Index Type VLAN Parameter ----- ---- ---- --------- 1 independant default Independent set identifier: 1 => eth bridge rule add Add a new c ...

  • Technicolor - Thomson ST536 - page 319

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 297 eth bridge vlan ifadd Add a bridge interface to a VLAN. SYNT AX: where: RELA TED COMMANDS: eth bridge vlan ifadd name = <string> intf = <string> [untagged = <{disabled | enabled}>] name The VLAN name to which a bri dge interface must be added. REQUIRE D intf The name of the bridge int ...

  • Technicolor - Thomson ST536 - page 320

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 298 eth bridge vlan ifconfig Modify a bridge interface from a VLAN. SYNT AX: where: RELA TED COMMANDS: eth bridge vlan ifconfig name = <string> intf = <string> untagged = <{disabled | enabled}> name The VLAN name for which a bridge interface must be modifie d. REQUIRED intf The name of t ...

  • Technicolor - Thomson ST536 - page 321

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 299 eth bridge vlan ifdelete Delete a bridge interf ace from a VLAN. SYNT AX: where: RELA TED COMMANDS: eth bridge vlan ifdelete name = <string> intf = <string> name The VLAN name for which a bridge interface must be deleted. REQUIRED intf The name of the bridge interface to b e deleted. REQUIR ...

  • Technicolor - Thomson ST536 - page 322

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 300 eth bridge vlan iflist Display all VLANs . SYNT AX: RELA TED COMMANDS: eth bridge vlan iflist eth bridge vlan ifadd Add a bridge interface to a VLAN. eth bridge vlan ifconfig Modify a bridge interface from a VLAN. eth bridge vlan ifdelete Delete a bridge interface from a VLAN . ...

  • Technicolor - Thomson ST536 - page 323

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 301 eth device ifconfig Configure an Ethe rnet interface. SYNT AX: where: eth device ifconfig intf = <string> [type = <{auto | 10BaseTHD | 10BaseTFD | 100BaseTHD| 100BaseTFD} or number>] [state = <{enabled | disabled}>] intf The name of a phys ical interface. REQUIRED type Th e Ethernet t ...

  • Technicolor - Thomson ST536 - page 324

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 302 EXAMPLE: RELA TED COMMANDS: =>eth device iflist Interface Type Result State ethif1 auto 100BaseTFD UP [forwarding] ethif2 auto 100BaseTFD UP [forwarding] ethif3 auto 100BaseTFD UP [forwarding] ethif4 auto 100BaseTFD UP [forwarding] usbif1 UP [forwarding] =>eth device ifconfig intf=ethif4 state=d ...

  • Technicolor - Thomson ST536 - page 325

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 303 eth device iflist Show status of Ethernet interfaces. SYNT AX: EXAMPLE: DESCRIPTION: > Ty p e : Indicates the configured Eth ernet communication speed and duplex mode. > Result : Indicates the effective op erating status if T ype e quals “auto” . In other cases, when t he Ethernet types do NO ...

  • Technicolor - Thomson ST536 - page 326

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 304 eth switch group flush Set all the ports to the default settings. All the ports are placed in group 0. SYNT AX: EXAMPLE: RELA TED COMMANDS: eth switch group flush =>eth switch group list Group 0 Ports: 4 Group 1 Ports: 1 Group 2 Ports: 2 3 =>eth switch group flush =>eth switch group list Grou ...

  • Technicolor - Thomson ST536 - page 327

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 305 eth switch group list List all the configured swi tch groups. SYNT AX: EXAMPLE: RELA TED COMMANDS: eth switch group list =>eth switch group list Group 0 Ports: 4 Group 1 Ports: 1 Group 2 Ports: 2 3 => eth switch group fl ush Set all the ports to the default settings. eth switch group m ove Move a ...

  • Technicolor - Thomson ST536 - page 328

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 306 eth switch group move Move a specified port t o a specified switch group. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: eth switch group move group = <number{0-3}> port = <number{1-4}> group A number be tween 0 and 4. Represents the gr oup ID to which the port must be moved. REQUIRED port A ...

  • Technicolor - Thomson ST536 - page 329

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 307 eth switch mirror capture Define the specified port to be th e Mirror Capture Port. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: i Only one port can be th e Mirror Capture Port at any one time. eth switch mirror capture port = <number{1-4}> port The port to be th e Mirror Capture Port. Note If no ...

  • Technicolor - Thomson ST536 - page 330

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 308 eth switch mirror egress Enable or disab le the specified port to be the Mirror Egress Po rt. SYNT AX: where: EXAMPLE: Here port 1 is enable d as Mirror Egress Port Here port 1 is disabled as Mirror Egress Port RELA TED COMMANDS: i Only one port can be th e Mirror Egress Port at any one t ime. But a p ...

  • Technicolor - Thomson ST536 - page 331

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 309 eth switch mirror ingress Enable or disab le the specified port to be the Mirror Ingress Port. SYNT AX: where: EXAMPLE: Here port 2 is enable d as Mirror Ingress Port Here port 2 is disabled as Mirror Ingress Port RELA TED COMMANDS: i Only one port can be th e Mirror Ingress Port at any one time. But a ...

  • Technicolor - Thomson ST536 - page 332

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 310 eth switch share add Add a port to be shared. SYNT AX: where: RELA TED COMMANDS: eth switch share add port = <number{1-4}> shared = <number{1-4}> port A number between 1 and 4. Represents the port. REQUIRED shared A number between 1 and 4. Represents the shared port. REQUIRED eth switch sh ...

  • Technicolor - Thomson ST536 - page 333

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 311 eth switch share delete Delete a shared port. SYNT AX: where: RELA TED COMMANDS: eth switch share delete port = <number{1-4}> shared = <number{1-4}> port A number between 1 and 4. Represents the port. REQUIRED shared A number between 1 and 4. Represents the shared port. REQUIRED eth switch ...

  • Technicolor - Thomson ST536 - page 334

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 312 eth switch share list Display shared ports. SYNT AX: RELA TED COMMANDS: eth switch share list eth switch share add Add a port to be shared . eth switch share delete Delete a shared port. ...

  • Technicolor - Thomson ST536 - page 335

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 313 eth switch info Display switch capabilities. SYNT AX: RELA TED COMMANDS: Not applicable eth switch info ...

  • Technicolor - Thomson ST536 - page 336

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 314 eth switch qos config Configure common qos parame ters. SYNT AX: where: RELA TED COMMANDS: eth switch qos config state = <disabled|enabled> [nbrOfQueues = <number{0-4}>] [realtime = <disabled|enabled>] state Enable or disable QoS REQUIRED nbrOfQueues Number of QoS queu es OPTIONAL re ...

  • Technicolor - Thomson ST536 - page 337

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 315 eth switch qos ifconfig Configure per port QoS parameters. SYNT AX: where: RELA TED COMMANDS: eth switch qos ifconfig port = <number{1-4}> mode = <802.1p|diffserv|high|none|tos> [flowcontrol = <disabled|enabled>] Port Port to be configured REQUIRED Mode QoS Classifi er for the port RE ...

  • Technicolor - Thomson ST536 - page 338

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 316 eth switch qos list Display QoS configuratio n. SYNT AX: RELA TED COMMANDS: eth switch qos list eth switch qos config Conf igure common qos parameters. eth switch qos ifconfig Configure per port QoS parameters. eth switch qos weights Configure the queue weights. ...

  • Technicolor - Thomson ST536 - page 339

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 317 eth switch qos weights Configure the queue weights. SYNT AX: where: RELA TED COMMANDS: eth switch qos weights queue0 = <number{0-100}> queue1 = <number{0-100}> queue2 = <number{0-100}> queue3 = <number{0-100}> QueueX The weight of qu eue X in WFQ (percentage) X=1 through 4 REQUI ...

  • Technicolor - Thomson ST536 - page 340

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 318 eth switch shaper config Configure common ing re ss shaper parameters. SYNT AX: where: RELA TED COMMANDS: eth switch shaper config shaper = <number{0-1}> [unicast = <disabled|enabled>] [multicast = <disabled|enabled>] [broadcast = <disabled|enabled>] [control = <disabled|ena ...

  • Technicolor - Thomson ST536 - page 341

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 319 eth switch shaper ifconfig Configure per port shaper parameters. SYNT AX: where: RELA TED COMMANDS: eth switch shaper ifconfig port = <number{1-4}> ingress = <disabled|enabled> shaper = <number{0-1}> [state = <disabled|enabled>] [speed = <number{64000-100000000}>] [burstsi ...

  • Technicolor - Thomson ST536 - page 342

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 320 eth switch shaper iflist Display shaper conf iguration per port. SYNT AX: RELA TED COMMANDS: eth switch shaper iflist eth switch shaper config Configur e common ingress sh aper parameters. eth switch shaper ifconf ig Config ure per port shaper parameters. ...

  • Technicolor - Thomson ST536 - page 343

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 321 eth switch storm ifconfig Configure per port storm con trol parameters. SYNT AX: where: RELA TED COMMANDS: eth switch storm ifconfig port = <number{1-4}> [state = <disabled|enabled>] [rate = <{33|50|100|200}>] [burstsize = <number{2-8}>] [broadcast = <disabled|enabled> [mu ...

  • Technicolor - Thomson ST536 - page 344

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 322 eth switch storm iflist Display storm control configuration per port. SYNT AX: RELA TED COMMANDS: eth switch storm iflist eth switch storm ifconfig Configure per port storm control param eters. ...

  • Technicolor - Thomson ST536 - page 345

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 323 eth vlan add Add a new VLAN. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: eth vlan add name = <string> vid = <number{2-4094}> [addrule = <{disabled | enabled}>] name The new VLAN name. REQUIRED vid A numb er representing th e new VLAN ID. Note The ID 1 is reserved for the default VLAN. ...

  • Technicolor - Thomson ST536 - page 346

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 324 eth vlan delete Delete a V LAN. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: eth vlan delete name = <string> name T he name of the VLAN to be de leted. REQUIRED =>eth vlan list Vid Name --- ---- 1 default 2 myVLAN =>eth vlan delete name=myVLAN vid=2 =>eth vlan list Vid Name --- ---- 1 de ...

  • Technicolor - Thomson ST536 - page 347

    E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 325 eth vlan flush Flush all VLA Ns. SYNT AX: EXAMPLE: i All the VLANs, except the de fault VLAN will be flushed. eth vlan flush =>eth vlan list Vid Name --- ---- 1 default 2 myVLAN 3 yourVLAN =>eth vlan flush =>eth vlan list Vid Name --- ---- 1 default => ...

  • Technicolor - Thomson ST536 - page 348

    E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 326 eth vlan list Display all VLANs . SYNT AX: EXAMPLE: RELA TED COMMANDS: eth vlan list =>eth vlan list Vid Name --- ---- 1 default 2 myVLAN => eth vlan add Add a new VLAN. eth vlan del ete Delete a VLAN. ...

  • Technicolor - Thomson ST536 - page 349

    E-DOC-CTC-20061 027-0003 v2.0 Expr Commands 327 15 Expr Commands Introduction This chapter describes the commands of the expr command group. Contents This chapter covers th e following commands: expr add Add a subexpression to an expression. 328 expr delete Delete an expression. 332 expr flush Flush all the expressions. 334 expr list List the expre ...

  • Technicolor - Thomson ST536 - page 350

    E-DOC-CTC- 20061027-0003 v2 .0 Expr Commands 328 expr add Add a subexp re ssion to an expression. SYNT AX: where: expr add name = <string> type = <{intf | ip | serv}> addr [!]= <ip-range> [intf [!]= <string>] [intfgroup [!]= <{wan|local|lan|tunnel|dmz|guest} or number>] [tos [!]= <number{0-255}>] [precedence [!]= ...

  • Technicolor - Thomson ST536 - page 351

    E-DOC-CTC-20061 027-0003 v2.0 Expr Commands 329 intfgroup The IP interface group. Choose between: > wan > local > lan > tunnel > dmz > guest. Note Only for expression ty pe intf . OP TIONAL tos A number between 0 and 25 5. Represents the T ype of Service (T oS) specification in the IP packet. Note The parameters to s , precedence ...

  • Technicolor - Thomson ST536 - page 352

    E-DOC-CTC- 20061027-0003 v2 .0 Expr Commands 330 icmpcode A nu mber between 0 and 15 . Represents the ICMP code (or begi nning of range) of the packet. OP TIONAL icmpcodeend A number between 0 and 15. Represents the ICMP code range end (inclusive). OP TIONAL ...

  • Technicolor - Thomson ST536 - page 353

    E-DOC-CTC-20061 027-0003 v2.0 Expr Commands 331 EXAMPLE: RELA TED COMMANDS: =>expr list name type use flags expression ------------------------------------------------------------------------------------------ _myPPP_ppp intf 0 D 1. intf=myPPP_ppp _eth0 intf 0 D 1. intf=eth0 wan intf 0 1. intfgroup=0 lan intf 28 1. intfgroup=2 local intf 0 1. in ...

  • Technicolor - Thomson ST536 - page 354

    E-DOC-CTC- 20061027-0003 v2 .0 Expr Commands 332 expr delete Delete an expression. SYNT AX: where: expr delete name = <string> [index = <number>] name The name of the expression to be deleted. REQUIRED index The index of the subexpression to be deleted. Note If not specified, all the subexpressions w il be deleted. OP TIONAL ...

  • Technicolor - Thomson ST536 - page 355

    E-DOC-CTC-20061 027-0003 v2.0 Expr Commands 333 EXAMPLE: RELA TED COMMANDS: =>expr list name type use flags expression ------------------------------------------------------------------------------------------ _myPPP_ppp intf 0 D 1. intf=myPPP_ppp _eth0 intf 0 D 1. intf=eth0 wan intf 0 1. intfgroup=0 lan intf 28 1. intfgroup=2 local intf 0 1. in ...

  • Technicolor - Thomson ST536 - page 356

    E-DOC-CTC- 20061027-0003 v2 .0 Expr Commands 334 expr flush Flush all the expressions. SYNT AX: expr flush ...

  • Technicolor - Thomson ST536 - page 357

    E-DOC-CTC-20061 027-0003 v2.0 Expr Commands 335 expr list List the expressions. SYNT AX: where: expr list [name = <string>] [type = <{intf | ip | serv}>] [format = <{pretty | cli}>] [string = <string>] [beginstring = <string>] name The na me of an existing expression . Note If not specified, all the expressions w ill b ...

  • Technicolor - Thomson ST536 - page 358

    E-DOC-CTC- 20061027-0003 v2 .0 Expr Commands 336 EXAMPLE 1: =>expr list name type use flags expression ------------------------------------------------------------------------------------------ _Internet intf 0 D 1. intf=Internet _LocalNetwork intf 0 D 1. intf=LocalNetwork HTTPI_if_0 intf 1 D 1. intf=LocalNetwork 2. intf=LocalNetwork 3. intf=Loc ...

  • Technicolor - Thomson ST536 - page 359

    E-DOC-CTC-20061 027-0003 v2.0 Expr Commands 337 EXAMPLE 2: =>expr list format=cli :expr add name=_Internet type=intf intf=Internet :expr add name=_LocalNetwork type=intf intf=LocalNetwork :expr add name=HTTPI_if_0 type=intf intf=LocalNetwork :expr add name=HTTPI_if_0 type=intf intf=LocalNetwork :expr add name=HTTPI_if_0 type=intf intf=LocalNetwo ...

  • Technicolor - Thomson ST536 - page 360

    E-DOC-CTC- 20061027-0003 v2 .0 Expr Commands 338 RELA TED COMMANDS: expr add Add a subexpression to an expression. expr delete Delete an expression. ...

  • Technicolor - Thomson ST536 - page 361

    E-DOC-CTC-20061 027-0003 v2.0 Expr Commands 339 expr modify Modify an expression. SYN T AX: where: expr modify name = <string> type = <{intf | ip | serv}> index = <number> addr [!]= <ip-range> [intf [!]= <string>] [intfgroup [!]= <{wan|local|lan|tunnel|dmz|guest} or number>] [bridgeport [!]= <number>] [tos ...

  • Technicolor - Thomson ST536 - page 362

    E-DOC-CTC- 20061027-0003 v2 .0 Expr Commands 340 intfgroup The IP interface group. Choose between: > wan > local > lan > tunnel > dmz > guest. Note Only for expression ty pe intf . OP TIONAL bridgeport The bridge port number . Note Only for expression ty pe intf . OP TIONAL tos A number between 0 and 25 5. Represents the T oS spec ...

  • Technicolor - Thomson ST536 - page 363

    E-DOC-CTC-20061 027-0003 v2.0 Expr Commands 341 icmpcode A nu mber between 0 and 15 . Represents the ICMP code (or begi nning of range) of the packet. OP TIONAL icmpcodeend A number between 0 and 15. Represents the ICMP code range end (inclusive). OP TIONAL ...

  • Technicolor - Thomson ST536 - page 364

    E-DOC-CTC- 20061027-0003 v2 .0 Expr Commands 342 ...

  • Technicolor - Thomson ST536 - page 365

    E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 343 16 Firewall Commands Introduction This chapter describes the commands of the firewa ll command grou p. Contents This chapter covers th e following commands: firewall config Configure the firewall options. 34 4 firewall clear Flush the firewall configuration. 346 firewall list List the firewall con ...

  • Technicolor - Thomson ST536 - page 366

    E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 344 firewall config Configure the fi rewall op tions. SYNT AX: where: firewall config [state = <{disabled | enabled}>] [keep = <{disabled | enabled}>] [tcpchecks = <{none | fast | exact}>] [udpchecks = <{disabled|enabled}>] [icmpchecks = <{disabled | enabled}>] [logdefau ...

  • Technicolor - Thomson ST536 - page 367

    E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 345 EXAMPLE: logdefault Disable or enable logging of d efault firewall rule. The defaul t is disabled . OP TIONAL logthreshol d Disable or enable lo g thresholdi ng. The defaul t is enabled . OP TIONAL tcpwindow A number be twe en 0 and 1073725440. This parameter perm its to modify the T CP window for ...

  • Technicolor - Thomson ST536 - page 368

    E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 346 firewall clear Flush the firewall configuration. SYNT AX: firewall clear ...

  • Technicolor - Thomson ST536 - page 369

    E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 347 firewall list List the firewall configuratio n. SYNT AX: where: firewall list [format = <{pretty | cli}>] format Select the output format in which the config uration must be shown. Choose between: > pr etty : the configuration is shown as intuitive output in clear text. > cli : the con ...

  • Technicolor - Thomson ST536 - page 370

    E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 348 EXAMPLE of output in text mode: EXAMPLE of output in CLI mode: =>firewall list Config ====== State : enabled Keep : disabled TcpChecks : exact TcpWindow : 65536 IcmpChecks : enabled LogDefault : disabled LogThreshold : enabled Modules ======= Module State Text Hooks --------------------------- ...

  • Technicolor - Thomson ST536 - page 371

    E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 349 firewall chain add Add a chain. SYNT AX: where: firewall chain add chain = <string> chain The name of the chai n to be added. RE QUIRED ...

  • Technicolor - Thomson ST536 - page 372

    E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 350 EXAMPLE: RELA TED COMMANDS: =>firewall chain list Chains ====== Name Description ----------------------------------------------------------------- sink system forward system source system sink_fire system forward_fire system source_fire system forward_host_service system forward_level system s ...

  • Technicolor - Thomson ST536 - page 373

    E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 351 firewall chain delete Delete a chain. SYNT AX: where: firewall chain delete chain = <string> chain The name of the chain to be deleted. RE QUIRED ...

  • Technicolor - Thomson ST536 - page 374

    E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 352 EXAMPLE: RELA TED COMMANDS: =>firewall chain list Chains ====== Name Description ----------------------------------------------------------------- sink system forward system source system sink_fire system forward_fire system source_fire system forward_host_service system forward_level system s ...

  • Technicolor - Thomson ST536 - page 375

    E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 353 firewall chain flush Flush all chains. SYNT AX: firewall chain flush ...

  • Technicolor - Thomson ST536 - page 376

    E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 354 firewall chain list List all chains. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: firewall chain list [format = <{pretty | cli}>] format Select the output format in which the chains must be shown. Choose between: > pr etty : the chains are shown as intuitive output in clear text. > cli ...

  • Technicolor - Thomson ST536 - page 377

    E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 355 firewall debug clear Clear the firewall statistics. SYNT AX: EXAMPLE: RELA TED COMMANDS: firewall debug clear =>firewall debug stats Statistics ========== Used rule contexts : 0 Total rule contexts : 256 Total packets parsed : 2554 Packets parsed in hook sink : 1461 Packets parsed in hook forwa ...

  • Technicolor - Thomson ST536 - page 378

    E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 356 firewall debug stats Display the firewall statistics. SYNT AX: EXAMPLE: RELA TED COMMANDS: firewall debug stats =>firewall debug stats Statistics ========== Used rule contexts : 0 Total rule contexts : 256 Total packets parsed : 2554 Packets parsed in hook sink : 1461 Packets parsed in hook fo ...

  • Technicolor - Thomson ST536 - page 379

    E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 357 firewall debug traceconfig Configure the firewa ll trace options. SYNT AX: where: EXAMPLE: firewall debug traceconfig [tcpchecks = <{disabled | enabled}>] [udpchecks = <{disabled|enabled}>] [icmpchecks = <{disabled | enabled}>] [sink = <{none | all | accept | deny | drop | res ...

  • Technicolor - Thomson ST536 - page 380

    E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 358 firewall level add Add a security level. SYNT AX: where: RELA TED COMMANDS: firewall level add name = <string> [index = <number>] [readonly = <{disabled | enabled}>] [udptrackmode = <{strict | loose}>] [service = <{disabled | enabled}>] [proxy = <{disabled|enabled ...

  • Technicolor - Thomson ST536 - page 381

    E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 359 firewall level delete Delete a security level. SYNT AX: where: RELA TED COMMANDS: firewall level delete name = <string> name The name of the security le vel to be deleted. REQU IRED firewall level add Add a security level. firewall level list List all the security levels. ...

  • Technicolor - Thomson ST536 - page 382

    E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 360 firewall level flush Flush the se curity level configuration. SYNT AX: firewall level flush ...

  • Technicolor - Thomson ST536 - page 383

    E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 361 firewall level list List all the security levels. SYNT AX: where: RELA TED COMMANDS: firewall level list [format = <{pretty | cli}>] [string = <string>] [beginstring = <string>] format Select the output format in which the se curity levels must be shown. Choose between: > pr e ...

  • Technicolor - Thomson ST536 - page 384

    E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 362 firewall level modify Configure a security level. SYNT AX: where: firewall level modify name = <string> [index = <number>] [readonly = <{disabled | enabled}>] [udptrackmode = <{strict | loose}>] [service = <{disabled | enabled}>] [proxy = <{disabled|enabled}>] ...

  • Technicolor - Thomson ST536 - page 385

    E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 363 firewall level set Set the security level or display the curr ent security level. SYNT AX: where: firewall level set [name = <string>] name The name of the secu rity level to be set. Note If no security level is spec ified, the current security level will be sho wn. OP TIONAL ...

  • Technicolor - Thomson ST536 - page 386

    E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 364 firewall rule add Add a firewall rule. SYNT AX: where: RELA TED COMMANDS: firewall rule add chain = <chain name> [index = <number>] [name = <string>] [clink = <chain name>] [srcintf [!]= <string>] [srcip [!]= <string>] [dstip [!]= <string>] [serv [!]= < ...

  • Technicolor - Thomson ST536 - page 387

    E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 365 firewall rule delete Delete a fi rewall rule . SYNT AX: where: RELA TED COMMANDS: firewall rule delete chain = <string> index = <number> chain The name of th e chain in which a rule m ust be deleted. REQUIRED index The number of the rule in the chain. REQUIRED firewall rule add Add a f ...

  • Technicolor - Thomson ST536 - page 388

    E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 366 firewall rule flush Flush all firewall rules. SYNT AX: where: firewall rule flush [chain = <string>] chain The name of th e chain for which the rules must be flushed. Note If not specifi ed, the rules of all the chains wi ll be flushed. OP TIONAL ...

  • Technicolor - Thomson ST536 - page 389

    E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 367 firewall rule list Show a list of the fi rewall rules in a chain. SYNT AX: where: firewall rule list [chain = <string>] [format = <{pretty | cli}>] [string = <string>] [beginstring = <string>] chain The name of the chain for which the rules must be listed. Note If not speci ...

  • Technicolor - Thomson ST536 - page 390

    E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 368 EXAMPLE: =>firewall rule list Rules (flags: C=Constant, D=Dynamic, E=Enable, L=Log) ===== Chain Nr. Flags Rule --------------------------------------------------------------------------------------- sink 1 CDE : link sink_fire 2 CDE : link sink_system_service sink_fire 1 C E SSDP : accept ssdp ...

  • Technicolor - Thomson ST536 - page 391

    E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 369 firewall rule modify Modify a firewall rule. SYNT AX: where: RELA TED COMMANDS: firewall rule modify chain = <string> index = <number> [newindex = <number>] [name = <string>] [clink = <chain name>] [srcintf [!]= <string>] [srcip [!]= <string>] [dstintf [!] ...

  • Technicolor - Thomson ST536 - page 392

    E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 370 firewall rule debug clear Clear the firewall rule statistics. SYNT AX: where: firewall rule debug clear [chain = <string>] [index = <number>] chain The name of the chain whi ch contains the rule. OP TIONAL index The number of the rule in the chain. Note If not specified, th e statis t ...

  • Technicolor - Thomson ST536 - page 393

    E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 371 EXAMPLE: RELA TED COMMANDS: =>firewall rule debug stats chain index packets bytes ---------------------------------------------------------------------------- sink 1 0 0 2 4 192 forward 1 0 0 200 3 10 480 source 1 0 0 sink_fire 1 0 0 source_fire 1 0 0 forward_level 1 10 480 sink_system_service ...

  • Technicolor - Thomson ST536 - page 394

    E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 372 firewall rule debug stats Show the firewall rule statistics. SYNT AX: where: firewall rule debug stats [chain = <chain name>] [index = <number>] chain The name of the chain for wh ich the statistics must be shown. Note If not specified, the statisti cs for all the chains will be shown ...

  • Technicolor - Thomson ST536 - page 395

    E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 373 EXAMPLE: RELA TED COMMANDS: =>firewall rule debug stats chain index packets bytes ---------------------------------------------------------------------------- sink 1 0 0 2 4 192 forward 1 0 0 200 3 10 480 source 1 0 0 sink_fire 1 0 0 source_fire 1 0 0 forward_level 1 10 480 sink_system_service ...

  • Technicolor - Thomson ST536 - page 396

    E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 374 firewall rule debug traceconfig Display or modify the ru le trace configuration. SYNT AX: where: EXAMPLE: firewall rule debug traceconfig [trace = <{disabled | enabled}>] trace Enable or disable rule traces. The defaul t is disabled . OP TIONAL =>firewall rule debug traceconfig :firewall ...

  • Technicolor - Thomson ST536 - page 397

    E-DOC-CTC-20061 027-0003 v2.0 GRP Commands 375 17 GRP Commands Introduction This chapter describes the commands of the grp comman d group. Contents This chapter covers th e following commands: grp config Set the Generic Routing Proto col (GRP) configuratio n settings. 376 grp flush Flush the GRP interface settings and parameters. 377 grp rtlist Sho ...

  • Technicolor - Thomson ST536 - page 398

    E-DOC-CTC- 20061027-0003 v2 .0 GRP Commands 376 grp config Set the Generic Rout ing Protocol (GRP) c onfiguration settings . SYNT AX: where: EXAMPLE: grp config [cdistance = <number{0-255}>] [kdistance = <number{0-255}>] [rdistance = <number{0-255}>] [trace = <{disabled | enabled}>] cdistance A number between 0 and 255 . Set ...

  • Technicolor - Thomson ST536 - page 399

    E-DOC-CTC-20061 027-0003 v2.0 GRP Commands 377 grp flush Flush the GRP interface setti ngs and parameters. SYNT AX: grp flush ...

  • Technicolor - Thomson ST536 - page 400

    E-DOC-CTC- 20061027-0003 v2 .0 GRP Commands 378 grp rtlist Show the current routes in th e GRP interfaces routing table. SYNT AX: where: EXAMPLE: grp rtlist [dst = <ip-address>] [dstmask = <ip-mask (dotted or cidr)>] dst The destination IP address of the route. Supports IP/mask not ation. Note If no destination IP address is speci fied, ...

  • Technicolor - Thomson ST536 - page 401

    E-DOC-CTC-20061 027-0003 v2.0 GRP Commands 379 grp rip config Configure the RIP settings. SYNT AX: where: grp rip config state = <{disabled | enabled}> [version = <{rip_unspec | rip_v1 | rip_v2}>] [defmetric = <number{1-16}>] [updatetime = <number{1-3600}>] [timeouttime = <number{1-3600}>] [garbagetime = <number{1-3 ...

  • Technicolor - Thomson ST536 - page 402

    E-DOC-CTC- 20061027-0003 v2 .0 GRP Commands 380 impsrt Enable or disable the import of static routes. The defaul t is enabled . OP TIONAL impdefkrt Enable o r disable the i mport of the default kerne l route. The defaul t is enabled . OP TIONAL impdefsrt Enable or disable the import of the default static route. The defaul t is enabled . OP TIONAL e ...

  • Technicolor - Thomson ST536 - page 403

    E-DOC-CTC-20061 027-0003 v2.0 GRP Commands 381 EXAMPLE: RELA TED COMMANDS: =>grp rip show RIP routing protocol config dump ------------------------------------ RIP daemon is enabled Global RIP queries received : 0 Global RIP route changes : 0 Default version : send rip_v2, receive rip_v2 Default redistribution metric is 1 Sending routing table u ...

  • Technicolor - Thomson ST536 - page 404

    E-DOC-CTC- 20061027-0003 v2 .0 GRP Commands 382 grp rip flush Flush the RIP inter face settings and global parameters. SYNT AX: grp rip flush ...

  • Technicolor - Thomson ST536 - page 405

    E-DOC-CTC-20061 027-0003 v2.0 GRP Commands 383 grp rip ifconfig Configure a RIP interface. SYNT AX: where: grp rip ifconfig intf = <string> [rip = <{disabled | enabled}>] [rxversion = <{rip_unspec | rip_v1 | rip_v2 | rip_v1-2}>] [authmode = <{none | cleartext}>] [authstring = <quoted string>] [splithorizon = <{disab ...

  • Technicolor - Thomson ST536 - page 406

    E-DOC-CTC- 20061027-0003 v2 .0 GRP Commands 384 EXAMPLE: =>grp rip ifconfig intf = myPPP_ppp [rip] = disabled [rxversion] = rip_unspec [authmode] = none [authstr] = [passive] = disabled [splithorizon] = enabled :grp rip ifconfig intf=myPPP_ppp => ...

  • Technicolor - Thomson ST536 - page 407

    E-DOC-CTC-20061 027-0003 v2.0 GRP Commands 385 grp rip show Show the RIP settings and the routes in the RIP database. SYNT AX: EXAMPLE: grp rip show =>grp rip show RIP routing protocol config dump ------------------------------------ RIP daemon is enabled Global RIP queries received : 0 Global RIP route changes : 3 Default version : send rip_v2, ...

  • Technicolor - Thomson ST536 - page 408

    E-DOC-CTC- 20061027-0003 v2 .0 GRP Commands 386 ...

  • Technicolor - Thomson ST536 - page 409

    E-DOC-CTC-20061 027-0003 v2.0 Hostmgr Commands 387 18 Hostmgr Commands Introduction This chapter describes the commands of the hostmg r command group. Contents This chapter covers th e following commands: hostmgr add Add host device info to the host manager . 388 hostmgr clear Remove al l the ho sts from the list. 390 hostmgr config Configure the h ...

  • Technicolor - Thomson ST536 - page 410

    E-DOC-CTC- 20061027-0003 v2 .0 Hostmgr Commands 388 hostmgr add Add host device info to the host manage r . SYNT AX: where: hostmgr add mac_addr = <hardware- address> [ip_addr = <ip-address>] [name = <string>] [type = <{generic_device|desktop_computer|laptop_computer| set_top_box|pda|gaming_console|phone|mobile_phone| printer|m ...

  • Technicolor - Thomson ST536 - page 411

    E-DOC-CTC-20061 027-0003 v2.0 Hostmgr Commands 389 EXAMPLE: RELA TED COMMANDS: =>hostmgr list MAC-address IP-address Flags Type Intf Hw Intf Hostname ----------- ---------- ----- ---- ---- ------- -------- 00:10:a4:ad:32:cf 192.168.1.64 C Generic Device LocalNetwork ethif4 MyComputer =>hostmgr add mac_addr=00:10:a4:33:56:53 name=Play type=Pla ...

  • Technicolor - Thomson ST536 - page 412

    E-DOC-CTC- 20061027-0003 v2 .0 Hostmgr Commands 390 hostmgr clear Remove all the hosts from the list. SYNT AX: EXAMPLE: RELA TED COMMANDS: hostmgr clear =>hostmgr list MAC-address IP-address Flags Type Intf Hw Intf Hostname ----------- ---------- ----- ---- ---- ------- -------- 00:10:a4:33:56:53 0.0.0.0 Playstation ethif1 ethif1 Play 00:10:a4:a ...

  • Technicolor - Thomson ST536 - page 413

    E-DOC-CTC-20061 027-0003 v2.0 Hostmgr Commands 391 hostmgr config Configure the host m anager parameters. SYNT AX: where: EXAMPLE: hostmgr config [state = <{disabled | enabled}>] [scantime = <number{10-600}>] [autosave = <{disabled | enabled}>] [trace = <{disabled | enabled}>] state Enable or disable the host manager daemon. ...

  • Technicolor - Thomson ST536 - page 414

    E-DOC-CTC- 20061027-0003 v2 .0 Hostmgr Commands 392 hostmgr delete Delete the host device info from the host manager . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: hostmgr delete mac_addr = <hardware-address> mac_addr The MAC address of the host to be rem oved. REQUIRED =>hostmgr list MAC-address IP-address Flags Type Intf Hw Intf Hostname ...

  • Technicolor - Thomson ST536 - page 415

    E-DOC-CTC-20061 027-0003 v2.0 Hostmgr Commands 393 hostmgr flush Flush the ho st manager configuration. The host manager configu ration is cleaned and returne d to default values. SYNT AX: hostmgr flush ...

  • Technicolor - Thomson ST536 - page 416

    E-DOC-CTC- 20061027-0003 v2 .0 Hostmgr Commands 394 hostmgr list List all the host devices. SYNT AX: EXAMPLE: RELA TED COMMANDS: hostmgr list =>hostmgr list MAC-address IP-address Flags Type Intf Hw Intf Hostname ----------- ---------- ----- ---- ---- ------- -------- 00:10:a4:33:56:53 0.0.0.0 Playstation ethif1 ethif1 Play 00:10:a4:ad:32:cf 192 ...

  • Technicolor - Thomson ST536 - page 417

    E-DOC-CTC-20061 027-0003 v2.0 IDS Commands 395 19 IDS Commands Introduction This chapter describ es the comma nds of the ids command group. Contents This chapter covers the fo llowing commands: ids clear Reset the IDS statistics. 396 ids config Display/modify th e Intrusion Detection System (IDS) configuration. 397 ids parser list Display the IDS p ...

  • Technicolor - Thomson ST536 - page 418

    E-DOC-CTC- 20061027-0003 v2 .0 IDS Commands 396 ids clear Reset the IDS statistics. SYNT AX: RELA TED COMMANDS: ids clear ids parser list Display the IDS parse r configurat ion. ...

  • Technicolor - Thomson ST536 - page 419

    E-DOC-CTC-20061 027-0003 v2.0 IDS Commands 397 ids config Display/modify the I ntrusion Detection System (IDS) configuratio n. SYNT AX: where: EXAMPLE: ids config [state = <{disabled | enabled}>] [trace = <{disabled|enabled}>] state Enable or disable IDS checks. The defau lt is enabled . OP TIONAL trace Enable or disable tracing. The de ...

  • Technicolor - Thomson ST536 - page 420

    E-DOC-CTC- 20061027-0003 v2 .0 IDS Commands 398 ids parser list Display the IDS parse r configuration. SYNT AX: where: EXAMPLE: ids parser list [parser = <parser>] parser The na me of the parser REQUIRED =>ids parser list parser state ----------------------------------------- fragment enabled scan enabled dos enabled proto enabled rate ena ...

  • Technicolor - Thomson ST536 - page 421

    E-DOC-CTC-20061 027-0003 v2.0 IDS Commands 399 ids parser modify Modify the IDS parser configuratio n. SYNT AX: where: ids parser modify parser = <string> state = <{disabled | enabled}> parser The na me of the IDS parser of which the configu ration must be modifi ed. REQUIRED state Disab le or enable the parser . REQUIR ED ...

  • Technicolor - Thomson ST536 - page 422

    E-DOC-CTC- 20061027-0003 v2 .0 IDS Commands 400 EXAMPLE: =>ids list Resources: ========== resource total maximum --------------------------------- parsers 5 10 signatures 38 50 Signatures: ========== parser signature hits action state --------------------------------------------------------------------------------------- fragment fragment sweep ...

  • Technicolor - Thomson ST536 - page 423

    E-DOC-CTC-20061 027-0003 v2.0 IDS Commands 401 ids pattern clear Reset the pattern tracker . SYNT AX: EXAMPLE: RELA TED COMMANDS: ids pattern clear =>ids pattern stats Pattern tracker statistics: --------------------------- memory : 32768 bytes maximum number of patterns : 512 number of active patterns : 8 number of recycled patterns : 0 number ...

  • Technicolor - Thomson ST536 - page 424

    E-DOC-CTC- 20061027-0003 v2 .0 IDS Commands 402 ids pattern list Display the patterns in the pattern tracker . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ids pattern list [size = <{10 | 100 | full} or number>] size Th e size of the IDS pattern li st that will be shown. Choose between: > 10 > 100 > full or , alternativ ely , specify ...

  • Technicolor - Thomson ST536 - page 425

    E-DOC-CTC-20061 027-0003 v2.0 IDS Commands 403 ids pattern stats Display the p attern tracker s tatistics. SYNT AX: EXAMPLE: RELA TED COMMANDS: ids pattern stats =>ids pattern stats Pattern tracker statistics: --------------------------- memory : 32768 bytes maximum number of patterns : 512 number of active patterns : 8 number of recycled patter ...

  • Technicolor - Thomson ST536 - page 426

    E-DOC-CTC- 20061027-0003 v2 .0 IDS Commands 404 ids signature list Displays the ids sign ature configuration SYNT AX where EXAMPLE: ids signature list [signature = <fragment_sweep|zero- length_fragment_size| small_fragment_size|fragment_size_ove rrun| fragment_overlap|fragment_out- of-order| ip_protocol_scan|tcp_port_scan|tcp_sy n_scan| stealth_ ...

  • Technicolor - Thomson ST536 - page 427

    E-DOC-CTC-20061 027-0003 v2.0 IDS Commands 405 ids signature modify Modify the states of the signatures. SYNT AX where EXAMPLE: ids signature modify [signature = <fragment_sweep| zero-length_fragment_size| small_fragment_size| fragment_size_overrun| fragment_overlap| fragment_out-of-order| ip_protocol_scan| tcp_port_scan|tcp_syn_scan| stealth_tc ...

  • Technicolor - Thomson ST536 - page 428

    E-DOC-CTC- 20061027-0003 v2 .0 IDS Commands 406 ids threshold clear Reset the IDS thresho lds to their default value s. SYNT AX: EXAMPLE: RELA TED COMMANDS: ids threshold clear =>ids threshold list index name window limit scaling ----------------------------------------------------------------- 1. ids scan 20 20 enabled 2. ids flood 2 100 disabl ...

  • Technicolor - Thomson ST536 - page 429

    E-DOC-CTC-20061 027-0003 v2.0 IDS Commands 407 ids threshold list Display the IDS thresholds. SYNT AX: EXAMPLE: RELA TED COMMANDS: ids threshold list =>ids threshold list index name window limit scaling ----------------------------------------------------------------- 1. ids scan 20 20 enabled 2. ids flood 2 100 disabled 3. ids tcp rate 1 200 di ...

  • Technicolor - Thomson ST536 - page 430

    E-DOC-CTC- 20061027-0003 v2 .0 IDS Commands 408 ids threshold modify Modify the IDS thresholds. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ids threshold modify index = <number> [window = <number>] [limit = <number>] [scaling = <{disabled | enabled}>] index The index o f the IDS threshold to be modified . Ti p Use the comman ...

  • Technicolor - Thomson ST536 - page 431

    E-DOC-CTC-20061 027-0003 v2.0 IGMP Commands 409 20 IGMP Commands Introduction This chapter describes the commands of the IGMP command group. Contents This chapter covers th e following commands: igmp host con fig Display or modify global IGMP co nfiguration. 41 0 igmp host flush Flush the IGMP settings. 411 igmp host lis t Show the IGMP groups. 412 ...

  • Technicolor - Thomson ST536 - page 432

    E-DOC-CTC- 20061027-0003 v2 .0 IGMP Commands 410 igmp host config Display or modify gl obal IGMP configurati on. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: igmp host config [requirera = <{disabled | enabled}>] requirera E nable or d isable the ro uter alert IP o ption check. The default is disabled . OPTIONAL =>igmp host confighostmgr lis ...

  • Technicolor - Thomson ST536 - page 433

    E-DOC-CTC-20061 027-0003 v2.0 IGMP Commands 411 igmp host flush Flush the IGMP settings. SYNT AX: igmp host flush ...

  • Technicolor - Thomson ST536 - page 434

    E-DOC-CTC- 20061027-0003 v2 .0 IGMP Commands 412 igmp host list Show the IGMP groups. SYNT AX: where: EXAMPLE: igmp host list [intf = <string>] [expand = <{disabled | enabled}>] intf The IP interface name. OP TIONAL expand Enable or disable expanded listing of IGMP grou ps. The default is disabled . OPTIONAL =>igmp host list Interfac ...

  • Technicolor - Thomson ST536 - page 435

    E-DOC-CTC-20061 027-0003 v2.0 IGMP Commands 413 igmp host ifconfig Configure an IG MP interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: igmp host ifconfig intf = <string> version = <{none |IGMPv1 |IGMPv2 |IGMPv3}> intf The IP interface name. REQUIRED version The IGMP version of the IP interface. Choose between: > IGMPv1 > IGM ...

  • Technicolor - Thomson ST536 - page 436

    E-DOC-CTC- 20061027-0003 v2 .0 IGMP Commands 414 igmp host iflist Show the configuration of the IGMP interfaces. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: igmp host iflist [expand = <{disabled | enabled}>] expand Enable or disable expanded listing of IGMP i nterfaces configuration. The default is disabled . OPTIONAL =>igmp host iflist In ...

  • Technicolor - Thomson ST536 - page 437

    E-DOC-CTC-20061 027-0003 v2.0 IGMP Commands 415 igmp host debug clear Clear IGMP statistics. SYNT AX: RELA TED COMMANDS: igmp host debug clear igmp host debu g stats Print IGMP statistics. ...

  • Technicolor - Thomson ST536 - page 438

    E-DOC-CTC- 20061027-0003 v2 .0 IGMP Commands 416 igmp host debug stats Print IGMP stati stics. SYNT AX: EXAMPLE: RELA TED COMMANDS: igmp host debug stats =>igmp host debug stats Total IGMP messages received : 0 Too small IGMP messages received : 0 Too long IGMP messages received : 0 IGMP messages with bad checksum received : 0 IGMP messages with ...

  • Technicolor - Thomson ST536 - page 439

    E-DOC-CTC-20061 027-0003 v2.0 IGMP Commands 417 igmp proxy config Configure the IGMP proxy . SYNT AX: where: igmp proxy config [state = <{disabled | enabled}>] [qi = <number{1-86400}>] [qri = <number{1-86400}>] [lmqi = <number{1-86400}>] [rv = <number{2-10}>] [requirera = <{disabled | enabled}>] [localgroup = < ...

  • Technicolor - Thomson ST536 - page 440

    E-DOC-CTC- 20061027-0003 v2 .0 IGMP Commands 418 EXAMPLE: RELA TED COMMANDS: =>igmp proxy config IGMP proxy state : disabled Query Interval : 0 days, 0:02:05 Query Response Interval : 0 days, 0:00:10 Last Member Query Interval : 0 days, 0:00:01 Robustness variable : 2 Router alert IP option check : disabled Process local multicast group : disabl ...

  • Technicolor - Thomson ST536 - page 441

    E-DOC-CTC-20061 027-0003 v2.0 IGMP Commands 419 igmp proxy flush Flush all IGM P proxy settings and learned groups. SYNT AX: igmp proxy flush ...

  • Technicolor - Thomson ST536 - page 442

    E-DOC-CTC- 20061027-0003 v2 .0 IGMP Commands 420 igmp proxy grouplist Show the learned group s on an IGMP proxy interface. SYNT AX: where: RELA TED COMMANDS: igmp proxy grouplist [intf = <string>] [expand = <{disabled | enabled}>] intf The name of the IGMP proxy in terface to be listed. OPTIONAL expand Enable or disable exp anded listin ...

  • Technicolor - Thomson ST536 - page 443

    E-DOC-CTC-20061 027-0003 v2.0 IGMP Commands 421 igmp proxy ifconfig Configure an IGMP proxy interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: igmp proxy ifconfig intf = <string> [state = <{inactive | downstream | upstream}>] [version = <{IGMPv1 | IGMPv2 | IGMPv3}>] [fastleave = <{disabled | enabled}>] intf The name of t ...

  • Technicolor - Thomson ST536 - page 444

    E-DOC-CTC- 20061027-0003 v2 .0 IGMP Commands 422 igmp proxy iflist Show the configuration of an IGMP proxy interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: igmp proxy iflist [expand = <{disabled | enabled}>] expand Enable or disable expanded listing of IGMP proxy interf ace configuration. The default is disabled . OPTIONAL =>igmp pro ...

  • Technicolor - Thomson ST536 - page 445

    E-DOC-CTC-20061 027-0003 v2.0 IGMP Commands 423 igmp proxy mbslist Show the IGMP proxy mem bership database (merge of all l earned groups. SYNT AX: igmp proxy mbslist ...

  • Technicolor - Thomson ST536 - page 446

    E-DOC-CTC- 20061027-0003 v2 .0 IGMP Commands 424 igmp proxy debug clear Clear IGMP proxy statistics. SYNT AX: RELA TED COMMANDS: igmp proxy debug clear igmp proxy debug stats Print IGMP proxy statis tics. igmp proxy debug traceco nfig Modify IG MP proxy trace configuratio n. ...

  • Technicolor - Thomson ST536 - page 447

    E-DOC-CTC-20061 027-0003 v2.0 IGMP Commands 425 igmp proxy debug stats Print IGMP proxy statistics. SYNT AX: EXAMPLE: RELA TED COMMANDS: igmp proxy debug stats =>igmp proxy debug stats IGMP proxy statistics: Total IGMP packets recv : 0 Too short IGMP packets recv : 0 IGMP packets with bad checksum recv : 0 IGMP packets with bad ttl recv : 0 IGMP ...

  • Technicolor - Thomson ST536 - page 448

    E-DOC-CTC- 20061027-0003 v2 .0 IGMP Commands 426 igmp proxy debug traceconfig Modify IGMP pro xy trace configuration. SYNT AX: where: RELA TED COMMANDS: igmp proxy debug traceconfig [state = <{disabled | enabled}>] state Enable or disable tr acing. The default is disabled . OPTIONAL igmp prox y debug clear Clear IGMP proxy statistics. igmp pr ...

  • Technicolor - Thomson ST536 - page 449

    E-DOC-CTC-20061 027-0003 v2.0 Interface Commands 427 21 Interface Commands Introduction This chapter describes the commands of the interf ace command group. Contents This chapter covers th e following commands: interface list Display interfaces. 428 ...

  • Technicolor - Thomson ST536 - page 450

    E-DOC-CTC- 20061027-0003 v2 .0 Interface Commands 428 interface list Display interfaces. SYNT AX: where: interface list [expand = <{disabled | enabled}>] [reverse = <{disabled | enabled}>] expand Enable or di sable expanded listing of interfaces. The default is disabled . OP TIONAL reverse Enable or disable reverse listing (l ower layer ...

  • Technicolor - Thomson ST536 - page 451

    E-DOC-CTC-20061 027-0003 v2.0 Interface Commands 429 EXAMPLE: =>interface list Name Type State Use UL Interfaces ethif1 physical connected 1 bridge ethif4 physical connected 1 bridge usbif1 physical connected 1 bridge RELAY eth connected 1 Internet_ppp bridge eth connected 1 eth0 atm_0_35 atm connected 1 ethoa_0_35 atm_8_35 atm connected 1 ethoa ...

  • Technicolor - Thomson ST536 - page 452

    E-DOC-CTC- 20061027-0003 v2 .0 Interface Commands 430 ...

  • Technicolor - Thomson ST536 - page 453

    E-DOC-CTC-20061 027-0003 v2.0 IP Commands 431 22 IP Commands Introduction This chapter describes the commands of the ip command group. Contents This chapter covers th e following commands: ip arpadd Add an entry to the ARP cache of a broadcast Internet Protocol (IP) interface. 433 ip arpdel ete Delete an entry fr om the ARP cache . 434 ip arplist D ...

  • Technicolor - Thomson ST536 - page 454

    E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 432 ip debug sendto Sen d UDP packets. 468 ip debug stats Display IP statistics. 470 ip debug traceconfig Display/modify the IP st ack trace configuration. 471 ...

  • Technicolor - Thomson ST536 - page 455

    E-DOC-CTC-20061 027-0003 v2.0 IP Commands 433 ip arpadd Add an entry to the ARP cache of a broa dcast Internet Protocol (IP) interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip arpadd intf = <string> ip = <ip-range> [hwaddr = <hardware-address>] intf The IP interface name. REQUIRED ip The IP address (or range) of the entry t ...

  • Technicolor - Thomson ST536 - page 456

    E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 434 ip arpdelete Delete an entry from the ARP cache. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip arpdelete intf = <string> ip = <ip-range> [hwaddr = <hardware-address>] intf The IP interface name. REQUIRED ip The IP address (or range) of the entry to b e deleted. REQUIRED hwaddr The ha ...

  • Technicolor - Thomson ST536 - page 457

    E-DOC-CTC-20061 027-0003 v2.0 IP Commands 435 ip arplist Display the ARP cache. SYNT AX: EXAMPLE: RELA TED COMMANDS: ip arplist =>ip arplist Interface IP-address HW-address Type 2 eth0 10.0.0.1 00:10:a4:ad:32:cf STATIC 2 eth0 10.0.0.2 00:00:00:00:00:00 DYNAMIC 2 eth0 10.0.0.3 00:a0:24:ae:66:e1 STATIC => ip arpadd Add an entry to the ARP cache ...

  • Technicolor - Thomson ST536 - page 458

    E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 436 ip config Show/set global IP stack configura tion options. SYNT AX: where: ip config [forwarding = <{disabled | enabled}>] [redirects = <{disabled | enabled}>] [checkoptions = <{disabled|enabled|transparent}>] [netbroadcasts = <{disabled | enabled}>] [ttl = <number{0-255}> ...

  • Technicolor - Thomson ST536 - page 459

    E-DOC-CTC-20061 027-0003 v2.0 IP Commands 437 EXAMPLE: addrcheck Set the level of IP address checks. Choose between: > of f : No address ch ecking is performed. For advanced users on ly; in normal circumstances there sh ould always be some kind of address checking. > own : Minimum level of checking. Only the address confi guration on the Th o ...

  • Technicolor - Thomson ST536 - page 460

    E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 438 ip flush Flush all the static IP par ameters. Dynamic configuration s (for example from PPP or CIP links) rema in. SYNT AX: i The flush command do es not impact previously save d configuration s. ! The command :ip flush deletes all local IP conn ectivity . Do not use this command during an IP based loc ...

  • Technicolor - Thomson ST536 - page 461

    E-DOC-CTC-20061 027-0003 v2.0 IP Commands 439 ip ifadd Create an IP interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip ifadd intf = <string> dest = <string> intf The name of the IP i nte rface to be created . REQUIRED dest An network interface name. REQUIRED =>ip iflist Interface Group MTU RX TX TX-Drop Status HW-address 0 loo ...

  • Technicolor - Thomson ST536 - page 462

    E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 440 ip ifattach Attach an IP in terface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip ifattach intf = <string> intf The name of the IP i nte rface to be attached. REQUIRED =>ip iflist Interface Group MTU RX TX TX-Drop Status HW-address 0 loop local 65535 123966 75177 0 [UP] 00:0e:50:0f:fc:2c 1 I ...

  • Technicolor - Thomson ST536 - page 463

    E-DOC-CTC-20061 027-0003 v2.0 IP Commands 441 ip ifconfig Configure the parameters of an IP interface. SYNT AX: where: ip ifconfig intf = <string> [mtu = <number{68-65535}>] [status = <{down | up}>] [hwaddr = <hardware-address>] [group = <string> or number] [linksensing = <{disabled | enabled}>] [primary = <{d ...

  • Technicolor - Thomson ST536 - page 464

    E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 442 EXAMPLE: =>ip iflist Interface Group MTU RX TX TX-Drop Status HW-address 0 loop local 65535 123966 75177 0 [UP] 00:0e:50:0f:fc:2c 1 Internet wan 1500 0 0 0 DOWN 2 RtPPPoE_ppp wan 1500 0 0 0 DOWN 3 LocalNetwork lan 1500 86589 125262 0 [UP] 00:0e:50:0f:fc:2c 4 myIPintf wan 1500 0 0 0 DOWN 00:0e:50:0f: ...

  • Technicolor - Thomson ST536 - page 465

    E-DOC-CTC-20061 027-0003 v2.0 IP Commands 443 ip ifdelete Delete an IP interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip ifdelete intf = <string> intf The name of the IP i nte rface to be deleted. REQUIRED =>ip iflist Interface Group MTU RX TX TX-Drop Status HW-address 0 loop local 65535 123966 75177 0 [UP] 00:0e:50:0f:fc:2c 1 Inte ...

  • Technicolor - Thomson ST536 - page 466

    E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 444 ip ifdetach Detach an IP interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip ifdetach intf = <string> intf The name of the IP i nte rface to be detached . REQUIRED =>ip iflist expand=enabled Interface Group MTU RX TX TX-Drop Status HW-address 0 loop local 65535 130597 82240 0 [UP] 00:0e: ...

  • Technicolor - Thomson ST536 - page 467

    E-DOC-CTC-20061 027-0003 v2.0 IP Commands 445 ip iflist Display all the IP interfaces. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip iflist [expand = <{disabled | enabled}>] [string = <string>] [beginstring = <string>] expand Enable or disa ble expanded listing. The default is disabled . OP TIONAL string String mat ching conditio ...

  • Technicolor - Thomson ST536 - page 468

    E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 446 ip ifwait W ait for a status change of an IP interface. SYNT AX: where: RELA TED COMMANDS: ip ifwait intf = <string> [timeout = <number{1-600000}>] [adminstatus = <{down | up}>] [operstatus = <{down | up}>] [linkstatus = <{down | up}>] intf The IP i nterface name. REQUIRED ...

  • Technicolor - Thomson ST536 - page 469

    E-DOC-CTC-20061 027-0003 v2.0 IP Commands 447 ip ipadd Assign an IP add ress to an IP interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip ipadd intf = <string> addr = <ip-address> [netmask = <ip-mask(dotted or cidr)>] [pointopoint = <ip-address>] [addroute = <{disabled | enabled}>] intf The IP interface name. REQ ...

  • Technicolor - Thomson ST536 - page 470

    E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 448 ip ipconfig Modify an IP ad dress configuration. SYNT AX: where: EXAMPLE: ip ipconfig addr = <ip-address> [preferred = <{disabled | enabled}>] [primary = <{disabled | enabled}>] addr The IP address t o be configured. REQUIRED preferred Make this IP address the preferre d address for t ...

  • Technicolor - Thomson ST536 - page 471

    E-DOC-CTC-20061 027-0003 v2.0 IP Commands 449 ip ipdelete Remove an IP address fr om an IP interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip ipdelete addr = <ip-address> addr The IP address to b e deleted. REQ UIRED =>ip iplist Interface Type IP-address Point-to-point/Mask 1 eth0 Ethernet 10.0.0.2 255.255.255.0 1 eth0 Ethernet 10.0 ...

  • Technicolor - Thomson ST536 - page 472

    E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 450 ip iplist Display all the configured IP addresses. SYNT AX: EXAMPLE: RELA TED COMMANDS: ip iplist =>ip iplist Interface Type IP-address Point-to-point/Mask 2 LocalNetwork Ethernet 10.0.0.138 255.255.255.0 2 LocalNetwork Ethernet *192.168.1.254 255.255.255.0 0 loop Ethernet 127.0.0.1 255.255.255.255 ...

  • Technicolor - Thomson ST536 - page 473

    E-DOC-CTC-20061 027-0003 v2.0 IP Commands 451 ip mcast rtadd Add a multi cast route to the multic ast routing table. SYNT AX: where: RELA TED COMMANDS: ip mcast rtadd srcintf = <string> [src = <ip-address>] grp = <ip-address> dstintf = <string> [ttl = <number{1-255}>] [ttlincr = {disabled | enabled}] srcintf The source ...

  • Technicolor - Thomson ST536 - page 474

    E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 452 ip mcast rtdelete Delete a multicast route from the multic ast routing table. SYNT AX: where: RELA TED COMMANDS: ip mcast rtdelete srcintf = <string> [src = <ip-address>] grp = <ip-address> dstintf = <string> srcintf The source IP interface. REQUIRED src The source IP address. O ...

  • Technicolor - Thomson ST536 - page 475

    E-DOC-CTC-20061 027-0003 v2.0 IP Commands 453 ip mcast rtlist Display the multic ast routing table. SYNT AX: where: RELA TED COMMANDS: ip mcast rtlist [expand = <{disabled | enabled}>}] expand Enable or disable expanded listin g. The default is disabled . OP TIONAL ip mcast rtadd Add a multicast route to the multicast routing table. ip mcast ...

  • Technicolor - Thomson ST536 - page 476

    E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 454 ip mcast flush Flush the multicast rout ing table. SYNT AX: RELA TED COMMANDS: ip mcast flush ip mcast rtadd Add a multicast route to the multicast routing table. ip mcast rtdelete Delete a multicast route from the multicast routing table. ip mcast rtlist Display the multicast routing table. ...

  • Technicolor - Thomson ST536 - page 477

    E-DOC-CTC-20061 027-0003 v2.0 IP Commands 455 ip rtadd Add a route to the routing table. SYNT AX: where: ip rtadd dst = <ip-address> [dstmsk = <ip-mask(dotted or cidr)>] [label = <string>] [gateway = <ip-address>] [intf = <string>] [srcintf = <string>] [metric = <number{0-255}>] dst The destination IP addre ...

  • Technicolor - Thomson ST536 - page 478

    E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 456 EXAMPLE: RELA TED COMMANDS: =>ip rtlist Destination Label Gateway Intf Mtrc Status 10.0.0.0/24 10.0.0.140 eth0 0 [UP] 10.0.0.140/32 10.0.0.140 eth0 0 [UP] 127.0.0.1/32 127.0.0.1 loop 0 [UP] =>ip rtadd dst=10.10.0.0/24 label=Interactive gateway=10.0.0.140 =>ip rtlist Destination Label Gateway I ...

  • Technicolor - Thomson ST536 - page 479

    E-DOC-CTC-20061 027-0003 v2.0 IP Commands 457 ip rtdelete Delete a route from the routing table. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip rtdelete dst = <ip-address> [dstmsk = <ip-mask(dotted or cidr)>] [label = <string>] [gateway = <ip-address>] [intf = <string>] dst The destination IP address(es) for this route ...

  • Technicolor - Thomson ST536 - page 480

    E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 458 ip rtlist Display the routing table. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip rtlist [expand = <{disabled | enabled}>] expand Enable or disable expanded listin g. The default is disabled . OP TIONAL =>ip rtlist Destination Label Gateway Interface Metric Status 10.0.0.138/32 127.0.0.1 loo ...

  • Technicolor - Thomson ST536 - page 481

    E-DOC-CTC-20061 027-0003 v2.0 IP Commands 459 ip auto flush Flush the auto IP interfaces. SYNT AX: ip auto flush ...

  • Technicolor - Thomson ST536 - page 482

    E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 460 ip auto ifadd Create an autoIP interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip auto ifadd intf = <string> [addr = <ip-address>] intf T he name of the IP interface for which a link-local ad dress has to be allocated. REQUIRED dest The preferred link-local IP address . OPTIONAL => ...

  • Technicolor - Thomson ST536 - page 483

    E-DOC-CTC-20061 027-0003 v2.0 IP Commands 461 ip auto ifattach Select and assign a link-local ad dress to an autoIP interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip auto ifattach intf = <string> intf The name of the autoIP in terface for which a link-local address has to be attached. REQUIRED => ip auto iflist ipsec0 : [INIT] 0.0. ...

  • Technicolor - Thomson ST536 - page 484

    E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 462 ip auto ifconfig Configure an autoIP interface. SYNT AX: where: ip auto ifconfig intf = <string> [addr = <ip-address>] [poolstart = <ip-address>] [poolend = <ip-address>] [netmask = <ip-mask(dotted or cidr)>] [claim = <number{0-65535}>] [defence = <number{0-65535} ...

  • Technicolor - Thomson ST536 - page 485

    E-DOC-CTC-20061 027-0003 v2.0 IP Commands 463 EXAMPLE: => ip auto iflist eth0 : [INIT] 0.0.0.0 poolstart = 169.254.1.1 poolend = 169.254.254.254 netmask = 255.255.0.0 claim : 10 defence : 5 probe : 4 interval : 2 (sec) probes sent = 0 collisions = 0 =>ip auto ifconfig intf=ipsec0 claim=5 probe=5 => ip auto iflist ipsec0 : [INIT] 0.0.0.0 po ...

  • Technicolor - Thomson ST536 - page 486

    E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 464 ip auto ifdelete Delete an existing autoIP interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip auto ifdelete intf = <string> intf The name of the IP i nte rface to be deleted. REQUIRED =>ip auto iflist ipsec0 : [SELECTING] 169.254.80.236 poolstart = 169.254.1.1 poolend = 169.254.254.254 ...

  • Technicolor - Thomson ST536 - page 487

    E-DOC-CTC-20061 027-0003 v2.0 IP Commands 465 ip auto ifdetach Release the link-local address for the given autoIP interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip auto ifdetach intf = <string> intf The name of the autoIP in terface for which a link-local address has to be detached. REQUIRED =>ip auto iflist ipsec0 : [SELECTING] 1 ...

  • Technicolor - Thomson ST536 - page 488

    E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 466 ip auto iflist Display the autoIP interfaces. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip auto iflist [intf = <string>] intf The name of the autoIP interface to be listed. Note If not specified, all the au toIP interfaces are shown. OP TIONAL =>ip auto iflist eth0 : [CLAIMED] 169.254.138.1 ...

  • Technicolor - Thomson ST536 - page 489

    E-DOC-CTC-20061 027-0003 v2.0 IP Commands 467 ip debug httpprobe Send a HTTP probe. This HTTP probe will meas ure the Round T rip T ime (RTT) taken to connect and access data from a HTTP server . SYNT AX: where: EXAMPLE: The first example shows the measured ti me for a file that was downloaded: If the URL of a normal HTML page is used the fig ure s ...

  • Technicolor - Thomson ST536 - page 490

    E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 468 ip debug sendto Send UDP packets. SYNT AX: where: ip debug sendto addr = <ip-address> [count = <number{1-1000000}>] [size = <number{0-20000}>] [interval = <number{1-1000000}>] [listen = <{disabled | enabled}>] [dffield = <{disabled | enabled}>] [srcaddr = <ip-addr ...

  • Technicolor - Thomson ST536 - page 491

    E-DOC-CTC-20061 027-0003 v2.0 IP Commands 469 EXAMPLE: =>ip debug sendto addr=10.0.0.148 listen=on srcport=19 dstport=1025 =>ip debug sendto addr=10.0.0.148 listen=on srcport=19 dstport=1025 1 bytes from 10.0.0.148:1025 41 A =>ip debug sendto addr=10.0.0.148 count=3 listen=on srcport=19 dstport=1025 1 bytes from 10.0.0.148:1025 41 A 1 byte ...

  • Technicolor - Thomson ST536 - page 492

    E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 470 ip debug stats Display IP statistics. SYNT AX: EXAMPLE: ip debug stats =>ip debug stats Total datagrams received : 8599 IP header errors : 0 Datagrams forwarded : 23 Datagram forwarding errors : 3 Datagram forwarding resource errors : 0 Total Fragments received : 0 Fragments dropped due to resources ...

  • Technicolor - Thomson ST536 - page 493

    E-DOC-CTC-20061 027-0003 v2.0 IP Commands 471 ip debug traceconfig Display/mod ify the IP st ack trace configura tion. SYNT AX: where: ip debug traceconfig [input = <{none | label | -telnet | -host | -broadcast | all}>] [forward = <{none | label | -telnet | -host | -broadcast | all}>] [output = <{none | label | -telnet | -host | -bro ...

  • Technicolor - Thomson ST536 - page 494

    E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 472 EXAMPLE: EXAMPLE: =>ip debug traceconfig Input traces : none Forward traces : none Output traces : none Drop traces : all Path traces : none Trace mode : line ARP traces : none => =>ip debug traceroute addr = 192.193.195.250 count=3 size=1 interval=1000 maxhops=30 dstport= 33433 maxfail=5 type ...

  • Technicolor - Thomson ST536 - page 495

    E-DOC-CTC-20061 027-0003 v2.0 IPQoS Commands 473 23 IPQoS Commands Introduction This chapter describes the commands of the ipqos comman d group. Contents This chapter covers th e following commands: ipqos config Configure IPQoS for a given dest ination interface for the IPQoS queues instantiation. 474 ipqos list Display the IPQoS configuration. 477 ...

  • Technicolor - Thomson ST536 - page 496

    E-DOC-CTC- 20061027-0003 v2 .0 IPQoS Commands 474 ipqos config Configure IPQoS for a given destination interface for the IPQoS qu eues instantiation . SYNT AX: where: i When enabling or disa bling IPQoS, ta ke the following into account: > if the W A N interface (for example PPPoA, IP oA,...) is detached at the time of enabling/disabling IPQoS, ...

  • Technicolor - Thomson ST536 - page 497

    E-DOC-CTC-20061 027-0003 v2.0 IPQoS Commands 475 priority Select the subq ueue priority algorithm. Choose betwee n: > wfq : W eighted Fair Q ueuing (WFQ) is used for th e four AF queues. The realtime queu e has priority over the WFQ queues, which have priority over the best-effort queue. > str ict : Priority queu ing is used. Strict Priority ...

  • Technicolor - Thomson ST536 - page 498

    E-DOC-CTC- 20061027-0003 v2 .0 IPQoS Commands 476 EXAMPLE: RELA TED COMMANDS: =>ipqos config dest=atm_pvc_8_35 state=enabled =>ipqos list Name State Discard Priority Size Size Rate Burst Weights (Packets) (KBytes) (%) (KBytes) Weights atm_pvc_0_35 disabled early wfq 250 56 80% 2 25% 25% 25% 25% atm_pvc_8_35 enabled early wfq 250 56 80% 2 25% ...

  • Technicolor - Thomson ST536 - page 499

    E-DOC-CTC-20061 027-0003 v2.0 IPQoS Commands 477 ipqos list Display the IPQoS con figuration. SYNT AX: EXAMPLE: RELA TED COMMANDS: ipqos list =>ipqos list Name State Discard Priority Size Size Rate Burst Weights (Packets) (KBytes) (%) (KBytes) Weights atm_pvc_0_35 disabled early wfq 250 56 80% 2 25% 25% 25% 25 % atm_pvc_8_35 enabled early wfq 25 ...

  • Technicolor - Thomson ST536 - page 500

    E-DOC-CTC- 20061027-0003 v2 .0 IPQoS Commands 478 ipqos ef config Configure the IPQoS Expedited Forwar ding (EF) timer for an interface. SYNT AX: where: EXAMPLE: The example below shows the de fault configuratio n: RELA TED COMMANDS: ipqos ef config intf = <string> [state = <{disabled | enabled}>] [timeout = <number{100-10000}>] [ ...

  • Technicolor - Thomson ST536 - page 501

    E-DOC-CTC-20061 027-0003 v2.0 IPQoS Commands 479 ipqos ef list Display the IPQoS EF timers. SYNT AX: EXAMPLE: RELA TED COMMANDS: ipqos ef list =>ipqos ef list Interface State Timeout MTU (ms) (bytes) loop disabled 1000 65535 Rt_PPPoA2 enabled 1000 1500 eth0 disabled 1000 1500 => ipqos ef config Configure the IPQoS Expedited Forwardi ng (EF) t ...

  • Technicolor - Thomson ST536 - page 502

    E-DOC-CTC- 20061027-0003 v2 .0 IPQoS Commands 480 ipqos ef stats Display the IPQoS EF timer statistics. SYNT AX: EXAMPLE: RELA TED COMMANDS: ipqos ef stats =>ipqos ef stats Interface State Remain (ms) loop active 900 Rt_PPPoA2 active 900 eth0 disabled 0 => ipqos ef config Configure the IPQoS Expedited Forwardi ng (EF) timer for an interface. ...

  • Technicolor - Thomson ST536 - page 503

    E-DOC-CTC-20061 027-0003 v2.0 IPQoS Commands 481 ipqos queue clear Clear the IPQoS statistics. SYNT AX: EXAMPLE: RELA TED COMMANDS: ipqos queue clear =>ipqos queue stats Name Queue # packets # packets # packets # packets # packets Marking added marked removed dropped replaced PVC_1 0 1240 0 1240 0 0 0 1 00000 0 2 00000 0 3 234 0 234 0 0 0 4 0000 ...

  • Technicolor - Thomson ST536 - page 504

    E-DOC-CTC- 20061027-0003 v2 .0 IPQoS Commands 482 ipqos queue config Modify the IPQoS subqueue configuration. SYNT AX: where: ipqos queue config dest = <string> queue = <number{0-5}> [propagate = <{disabled | enabled}>] [ecnmarking = <{disabled | enabled}>] [ackfiltering = <{disabled | enabled}>] [maxpackets = <numb ...

  • Technicolor - Thomson ST536 - page 505

    E-DOC-CTC-20061 027-0003 v2.0 IPQoS Commands 483 EXAMPLE: RELA TED COMMANDS: maxbytes A number between 0 and 128. Represents the maxim um size in kilobytes of this q ueue. The default is 0 for the Real time que ue and 20 for the other queues. Note 0 means that a maximum size is not enforced. OP TIONAL respackets A numbe r between 0 and 250. Represe ...

  • Technicolor - Thomson ST536 - page 506

    E-DOC-CTC- 20061027-0003 v2 .0 IPQoS Commands 484 ipqos queue list Display the IPQoS subq ueue configuration. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ipqos queue list [dest = <string}>] dest The destination interface for the IPQoS queues instantiation. This is an A TM phonebook entry . Note If not specified, the IPQoS subqueue configurati ...

  • Technicolor - Thomson ST536 - page 507

    E-DOC-CTC-20061 027-0003 v2.0 IPQoS Commands 485 ipqos queue stats Show the IPQoS subq ueue statistics. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ipqos queue stats [dest = <string}>] dest The destination interface for the IPQoS queues instantiation. This is an A TM phonebook entry . Note If not specified, the IPQoS subqueue statistics for a ...

  • Technicolor - Thomson ST536 - page 508

    E-DOC-CTC- 20061027-0003 v2 .0 IPQoS Commands 486 ...

  • Technicolor - Thomson ST536 - page 509

    E-DOC-CTC-20061 027-0003 v2.0 Label Commands 487 24 Label Commands Introduction This chapter describes the commands of the label comman d group. Contents This chapter covers th e following commands: label add Create a new label. 488 label delete Del ete a label. 489 label flush Flush all labels. 490 label list Display the labels. 491 label modify M ...

  • Technicolor - Thomson ST536 - page 510

    E-DOC-CTC- 20061027-0003 v2 .0 Label Commands 488 label add Create a new label. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: label add name = <string> name The name of the labe l to be ad ded. REQUIRED =>label list Name Class Def Ack Bidirect Inherit Tosmark Type Value Ttlover Ttl Use Trace DSCP overwrite dscp defclass disabled disabled dis ...

  • Technicolor - Thomson ST536 - page 511

    E-DOC-CTC-20061 027-0003 v2.0 Label Commands 489 label delete Delete a label. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: label delete name = <string> [force = <{disabled | enabled}>] name The name of the label to be deleted. REQ UIRED force Force delete and cl eanup references e ven when the label is still in use (ena bled) or not (di ...

  • Technicolor - Thomson ST536 - page 512

    E-DOC-CTC- 20061027-0003 v2 .0 Label Commands 490 label flush Flush all labels. SYNT AX: i The flush command do es not impact previously saved configurations. label flush ...

  • Technicolor - Thomson ST536 - page 513

    E-DOC-CTC-20061 027-0003 v2.0 Label Commands 491 label list Display the labels. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: label list [name = <string>] name The name of the label to be displayed . Note If not specified, all the labels will be displayed. OP TIONAL =>label list Name Class Def Ack Bidirect Inherit Tosmark Type Value Ttlover ...

  • Technicolor - Thomson ST536 - page 514

    E-DOC-CTC- 20061027-0003 v2 .0 Label Commands 492 label modify Modify a label configuratio n. SYNT AX: where: label modify name = <string> [classification = <{ignore | overwrite | increase}>] [defclass = <number{0-15} | dscp | default>] [ackclass = <number{0-15} | defclass | prioritize>] [bidirectional = <{disabled | enab ...

  • Technicolor - Thomson ST536 - page 515

    E-DOC-CTC-20061 027-0003 v2.0 Label Commands 493 ackclass The priority cla ss of the ACK segments of the TCP connection. Choose between: > A number between 0 an d 15 > prioritize > defclass. The default is 0 . OP TIONAL bidirectional The label applies to the initiator stream, the returning stream (the current connection) as well as to the ...

  • Technicolor - Thomson ST536 - page 516

    E-DOC-CTC- 20061027-0003 v2 .0 Label Commands 494 EXAMPLE: =>label list Name Class Def Ack Bidirect Inherit Tos mark Type Value Use Trace DSCP overwrite dscp defclass disabled disabled disabled tos 0 0 0 disabled Interactive increase 8 8 disabled disabled disabled tos 0 0 0 disabled Management increase 12 12 disabled disabled disabled tos 0 0 0 ...

  • Technicolor - Thomson ST536 - page 517

    E-DOC-CTC-20061 027-0003 v2.0 Label Commands 495 label chain add Add a new label chain. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: label chain add chain = <string> chain The nam e of the chain to be added. REQUIRED =>label chain list Chains ====== Name Description ------------------------------------------------- routing_labels system rt_ ...

  • Technicolor - Thomson ST536 - page 518

    E-DOC-CTC- 20061027-0003 v2 .0 Label Commands 496 label chain delete Delete a label chain. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: label chain delete chain = <string> chain The nam e of the chain to be deleted. REQUIRED =>label chain list Chains ====== Name Description ------------------------------------------------- routing_labels sy ...

  • Technicolor - Thomson ST536 - page 519

    E-DOC-CTC-20061 027-0003 v2.0 Label Commands 497 label chain flush Flush all label chain s. SYNT AX: label chain flush ...

  • Technicolor - Thomson ST536 - page 520

    E-DOC-CTC- 20061027-0003 v2 .0 Label Commands 498 label chain list Display a list of chains. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: label chain list [format = <{pretty | cli}>] format Select the output format of the list. Choose between: > pret ty : the configuration is show n as intuitive output in clear text. > cli : the configur ...

  • Technicolor - Thomson ST536 - page 521

    E-DOC-CTC-20061 027-0003 v2.0 Label Commands 499 label rule add Add a label rule. SYNT AX: where: label rule add chain = <chain name> [index = <number>] [name = <string>] [clink = <chain name>] [srcintf [!]= <string>] [srcip [!]= <{ip address | private}>] [dstip [!]= <{ip address | private}>] [serv [!]= < ...

  • Technicolor - Thomson ST536 - page 522

    E-DOC-CTC- 20061027-0003 v2 .0 Label Commands 500 EXAMPLE: RELA TED COMMANDS: =>label rule list Rules (flags: C=Constant, D=Dynamic, E=Enabl e, L=Log) ===== Chain Nr. Flags Rule ----------------------------------- ------------------------------------------------------ ---- routing_labels 1 CDE : link rt_user_labels 2 CDE : link rt_default_labels ...

  • Technicolor - Thomson ST536 - page 523

    E-DOC-CTC-20061 027-0003 v2.0 Label Commands 501 label rule list Display a list of label rules. ...

  • Technicolor - Thomson ST536 - page 524

    E-DOC-CTC- 20061027-0003 v2 .0 Label Commands 502 label rule delete Delete a label rule. SYNT AX: where: EXAMPLE: label rule delete chain = <string> index = <number> chain The nam e of the chain in whic h a rule must be deleted. REQUIRED index The index number of the rule in the chain. Ti p Use the command :label rule l ist to obtain th ...

  • Technicolor - Thomson ST536 - page 525

    E-DOC-CTC-20061 027-0003 v2.0 Label Commands 503 RELA TED COMMANDS: label rule add Add a label rule. label rule list Display a list of label rules. ...

  • Technicolor - Thomson ST536 - page 526

    E-DOC-CTC- 20061027-0003 v2 .0 Label Commands 504 label rule flush Flush all label rules. The chains themselves are not removed. SYNT AX: where: i The flush command do es not impact previously saved configurations. label rule flush [chain = <string>] chain The nam e of the chain to be flushed. Note If not specified, all the ru les for all the ...

  • Technicolor - Thomson ST536 - page 527

    E-DOC-CTC-20061 027-0003 v2.0 Label Commands 505 label rule list Display a list of label rules. SYNT AX: where: label rule list [chain = <string>] [format = <{pretty | cli}>] [string = <string>] [beginstring = <string>] chain The name of the chain for which the rules must be listed. Note If not specified, all rules for all c ...

  • Technicolor - Thomson ST536 - page 528

    E-DOC-CTC- 20061027-0003 v2 .0 Label Commands 506 EXAMPLE: RELA TED COMMANDS: =>label rule list format=cli :label rule add chain=qos_default_labels index=1 serv=sip log=disabled state=enabled label=VoIP :label rule add chain=qos_default_labels index=2 serv=h323 log=disabled state=enabled label=VoIP :label rule add chain=qos_default_labels index= ...

  • Technicolor - Thomson ST536 - page 529

    E-DOC-CTC-20061 027-0003 v2.0 Label Commands 507 label rule modify Modify a label rule. SYNT AX: where: label rule modify chain = <chain name> index = <number> [newindex = <number>] [name = <string>] [clink = <chain name>] [srcintf [!]= <string>] [srcip [!]= <{ip address | private}>] [dstip [!]= <{ip add ...

  • Technicolor - Thomson ST536 - page 530

    E-DOC-CTC- 20061027-0003 v2 .0 Label Commands 508 label rule debug clear Clear the label rule statistics. SYNT AX: where: label rule debug clea r [chain = <string>] [index = <number>] chain The name of the chain in which the rule is to be found. Note If not specified, the statistics for all the rules in all chains will be cleared. OP TI ...

  • Technicolor - Thomson ST536 - page 531

    E-DOC-CTC-20061 027-0003 v2.0 Label Commands 509 EXAMPLE: RELA TED COMMANDS: =>label rule debug stats chain=qos_labels chain index packets bytes ------------------------------------------------------------ qos_labels 1 0 0 2 203 19146 =>label rule debug clear chain=qos_labels =>label rule debug stats chain index packets bytes ------------- ...

  • Technicolor - Thomson ST536 - page 532

    E-DOC-CTC- 20061027-0003 v2 .0 Label Commands 510 label rule debug stats Display the label ru le statistics. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: label rule debug stat s [chain = <string>] [index = <number>] chain The nam e of the chain for wh ich the statistics must be shown. Note If not specified, the statistics for the rules a ...

  • Technicolor - Thomson ST536 - page 533

    E-DOC-CTC-20061 027-0003 v2.0 Label Commands 511 label rule debug traceconfig Display or modify the ru le trace configuration. SYNT AX: where: EXAMPLE: label rule debug trac econfig [trace = <{disabled | enabled}>] trace Disable or enable rule traces. The default is disabled . OP TIONAL =>label rule debug traceconfig :label rule debug trac ...

  • Technicolor - Thomson ST536 - page 534

    E-DOC-CTC- 20061027-0003 v2 .0 Label Commands 512 ...

  • Technicolor - Thomson ST536 - page 535

    E-DOC-CTC-20061 027-0003 v2.0 Language Commands 513 25 Language Commands Introduction This chapter describes the commands of the langua ge command grou p. Contents This chapter covers th e following commands: language config Select a language. 514 language delete Delete one or all language archives. 515 language list List the available language arc ...

  • Technicolor - Thomson ST536 - page 536

    E-DOC-CTC- 20061027-0003 v2 .0 Language Commands 514 language config Select a langua ge. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: language config [language = <string>] [complete = <{yes | no}>] language Langu age code: OSI langua ge code (2 chars) for language. Example: en for english. OP TIONAL complete Enab le transl ation for expe ...

  • Technicolor - Thomson ST536 - page 537

    E-DOC-CTC-20061 027-0003 v2.0 Language Commands 515 language delete Delete one or all language arch ives. SYNT AX: where: RELA TED COMMANDS: language delete [file = <string>] [all = <{yes | no}>] file The filename of the lang uage archive to be removed. OP TIONAL all Remove all languages arch ives (yes) or not (no). The defaul t is no . ...

  • Technicolor - Thomson ST536 - page 538

    Language Commands E-DOC-CTC- 20061027-0003 v2 .0 516 language list List the available language archives. SYNT AX: EXAMPLE: RELA TED COMMANDS: language list =>language list CODE LANGUAGE VERSION FILENAME en* English 5.3.0.10.0 <system> => i The currently sele cted language is indicate d by a “*” next to the OSI language code. languag ...

  • Technicolor - Thomson ST536 - page 539

    E-DOC-CTC-20061 027-0003 v2.0 MBUS Commands 517 26 MBUS Commands Introduction This chapter describes the commands of the mbus command group. Contents This chapter covers th e following commands: mbus client config Modify clie nt parameters. 518 mbus client exec Execute mbus command. 519 mbus client regi ster Register cli client to mbus. 521 mbus de ...

  • Technicolor - Thomson ST536 - page 540

    E-DOC-CTC- 20061027-0003 v2 .0 MBUS Commands 518 mbus client config Modify clie nt parameters. SYNT AX: where: RELA TED COMMANDS: mbus client config [writelock = <{enabled | disabled}>] [wlgetimeout = <number>] [wlidletimeout = <number>] [path = <quoted string>] [type = <idpath | keypath>] writelock Enabl e or disable ...

  • Technicolor - Thomson ST536 - page 541

    E-DOC-CTC-20061 027-0003 v2.0 MBUS Commands 519 mbus client exec Execute mbus command. SYNT AX: where: mbus client exec cmd = <{addobject | deleteobject | getparamattr ibutes | getparamcount | getparamnames | getparamvalues | getpath | setparamvalue}> [param = <quoted string>] [value = <quoted string>] [gettype = <{object | par ...

  • Technicolor - Thomson ST536 - page 542

    E-DOC-CTC- 20061027-0003 v2 .0 MBUS Commands 520 RELA TED COMMANDS: mbus client config Modify client parameters. mbus client regi ster Register cli cl ie nt to mbus. mbus debug stats Display mbus statistics. ...

  • Technicolor - Thomson ST536 - page 543

    E-DOC-CTC-20061 027-0003 v2.0 MBUS Commands 521 mbus client register Register cli client to mbus. SYNT AX: RELA TED COMMANDS: mbus client register mbus client config Modify client parameters. mbus client exec Execute mbus co mmand. mbus debug stats Display mbus statistics. ...

  • Technicolor - Thomson ST536 - page 544

    E-DOC-CTC- 20061027-0003 v2 .0 MBUS Commands 522 mbus debug stats Display mbus statistics. SYNT AX: RELA TED COMMANDS: mbus debug stats mbus debug traceconfig Modify mbus trace settings. ...

  • Technicolor - Thomson ST536 - page 545

    E-DOC-CTC-20061 027-0003 v2.0 MBUS Commands 523 mbus debug clearstats Reset MBUS statistics . SYNT AX: RELA TED COMMANDS: mbus debug clearstats mbus debug stats Display mbus statistics. mbus debug trac econfig Modify mbus trace settings. ...

  • Technicolor - Thomson ST536 - page 546

    E-DOC-CTC- 20061027-0003 v2 .0 MBUS Commands 524 mbus debug traceconfig Modify mbus trace settings. SYNT AX: where: RELA TED COMMANDS: mbus debug traceconfig [level = <number{0-4}>] level A number between 0 and 4. Represents the mbus trace level. OP TIONAL mbus debug stats Display mbus statistics. ...

  • Technicolor - Thomson ST536 - page 547

    E-DOC-CTC-20061 027-0003 v2.0 MBUS Commands 525 mbus listobjects Display the object instances. SYNT AX: where: RELA TED COMMANDS: mbus listobjects [path = <quoted string>] [type = <{idpath | keypath}>] [output = <{list | tree}>] [expand = <{disabled | enabled}>] path Fully qualified m bus path to list. OP TIONAL type Path ty ...

  • Technicolor - Thomson ST536 - page 548

    E-DOC-CTC- 20061027-0003 v2 .0 MBUS Commands 526 mbus listtypes Display the registered objecttypes. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: mbus listtypes [path = <quoted string>] [expand = <{disabled | enabled}>] path Fully qualified m bus path to list. OP TIONAL expand Enable or disable details. The default is disabled . OP TIONAL ...

  • Technicolor - Thomson ST536 - page 549

    E-DOC-CTC-20061 027-0003 v2.0 MBUS Commands 527 mbus listenums Display the registered enumtypes. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: mbus listenumss [dmtree = <{igd|atomic|system}>] [name = <quoted string>] [expand = <{disabled|enabled}>] dmtree Select mbusd da tamodel tree. OPTIONAL name Filter enumtypes by (part of) the ...

  • Technicolor - Thomson ST536 - page 550

    E-DOC-CTC- 20061027-0003 v2 .0 MBUS Commands 528 mbus listcontexts Display the context instances . SYNT AX: where: RELA TED COMMANDS: listcontexts [dmtree = <{igd|atomic|system}>] dmtree Select mbusd da tamodel tree. OPTIONAL mbus listobjects Display the object instances. mbus listtypes Display the registered objecttypes. mbus listenums Displ ...

  • Technicolor - Thomson ST536 - page 551

    E-DOC-CTC-20061 027-0003 v2.0 MBUS Commands 529 mbus listsubscriptions Display the subscrip tion instances . SYNT AX: where: RELA TED COMMANDS: listsubscriptions [dmtree = <{igd|atomic|system}>] dmtree Select mbusd da tamodel tree. OPTIONAL mbus listobjects Display the object instances. mbus listtypes Display the regist ered objecttypes. mbus ...

  • Technicolor - Thomson ST536 - page 552

    E-DOC-CTC- 20061027-0003 v2 .0 MBUS Commands 530 mbus debug loadobjects Load object instances of registered objecttypes. SYNT AX: where: RELA TED COMMANDS: mbus debug loadobjects [dmtree = <{igd|atomic|system}>] [path = <quoted string>] [type = <{indexpath|objidpath|keystrpath}>] [flush = <{disabled|enabled}>] dmtree mbus da ...

  • Technicolor - Thomson ST536 - page 553

    E-DOC-CTC-20061 027-0003 v2.0 MBUS Commands 531 mbus debug unloadobjects Unload object inst ances. SYNT AX: where: RELA TED COMMANDS: mbus unloadobjects [path = <quoted string>] [type = <{idpath | keypath}>] path Fully qualified m bus path. OP TIONAL type Path type. Choose between: > idpath > k eypath . The default is idpath . OP ...

  • Technicolor - Thomson ST536 - page 554

    E-DOC-CTC- 20061027-0003 v2 .0 MBUS Commands 532 mbus pluginevent Simulate event from plugin . SYNT AX: where: mbus pluginevent ctxid = <number{0--2}> type = <{addobj|delobj|updobj}> path = <quoted string> [name = <quoted string>] [value = <quoted string>] [orivalue = <quoted string>] ctxid Plugin context i d typ ...

  • Technicolor - Thomson ST536 - page 555

    E-DOC-CTC-20061 027-0003 v2.0 MBUS Commands 533 mbus unregister Unregister a client/p lugin context . SYNT AX: where: unregister id = <number> id message-based client/plugin con text id. ...

  • Technicolor - Thomson ST536 - page 556

    E-DOC-CTC- 20061027-0003 v2 .0 MBUS Commands 534 mbus client unregister Unregister cli client from mbus . SYNT AX: unregister ...

  • Technicolor - Thomson ST536 - page 557

    E-DOC-CTC-20061 027-0003 v2.0 MEMM Commands 535 27 MEMM Commands Introduction This chapter describes the commands of the memm command group. Contents This chapter covers th e following commands: memm debug lock traceconfig Modify lock trace settings. 536 memm debug traceconfig Modify memm trace settings. 537 memm debug clearstats Display memm stati ...

  • Technicolor - Thomson ST536 - page 558

    E-DOC-CTC- 20061027-0003 v2 .0 MEMM Commands 536 memm debug lock traceconfig Modify lock trace settings. SYNT AX: where: memm debug lock traceconfig [level = <number{0-4}>] [name = <string>] level A number betwe en 0 and 4. Represents the memm trace level. OP TIONAL name Application nam e filter for lock traces (empty di splays all lock ...

  • Technicolor - Thomson ST536 - page 559

    E-DOC-CTC-20061 027-0003 v2.0 MEMM Commands 537 memm debug traceconfig Modify memm trace settings. SYNT AX: where: memm debug traceconfig [level = <number{0-4}>] level A number betwe en 0 and 4. Represents the memm trace level. OP TIONAL ...

  • Technicolor - Thomson ST536 - page 560

    E-DOC-CTC- 20061027-0003 v2 .0 MEMM Commands 538 memm debug clearstats Clear time statistics SYNT AX: memm debug clearstats ...

  • Technicolor - Thomson ST536 - page 561

    E-DOC-CTC-20061 027-0003 v2.0 MEMM Commands 539 memm debug lock stats Display lock statistics SYNT AX: memm debug lock stats ...

  • Technicolor - Thomson ST536 - page 562

    E-DOC-CTC- 20061027-0003 v2 .0 MEMM Commands 540 memm listobjects Display objects. SYNT AX: where: memm listobjects [name = <quoted string>] name Select typename(s) to list (s upports partial typename). OPTIONAL ...

  • Technicolor - Thomson ST536 - page 563

    E-DOC-CTC-20061 027-0003 v2.0 MEMM Commands 541 memm stats Display memm statistics. SYNT AX: where: EXAMPLE: memm stats [name = <quoted string>] name Select typename(s) to list (s upports partial typename). OPTIONAL =>memm stats pool name bytes cur,max,avail (m ax.%) count cur,max,avail ref cur,max,avail --------- -------------- ---------- ...

  • Technicolor - Thomson ST536 - page 564

    E-DOC-CTC- 20061027-0003 v2 .0 MEMM Commands 542 EXAMPLE: =>memm stats pool name bytes cur,max,avail (max.%) count cur,max,avail ref cur,max,avail ------------- --------------------------- ------------------ - --- memm_pooldesc 1196, 1196, 1300 ( 92%) 23, 23, 25 ob j: 0, 255 dynstr_pool 72, 72, 120 ( 60%) 3, 3, 5 0, 0, - mbus_llist 2460, 2532, 4 ...

  • Technicolor - Thomson ST536 - page 565

    E-DOC-CTC-20061 027-0003 v2.0 MLP Commands 543 28 MLP Commands Introduction This chapter describes the commands of the mlp comman d group. Contents This chapter covers th e following commands: mlp flush Flush all the Multi-Level access Policies (MLP) structures. 544 mlp import Import all the scores. 54 5 mlp debug export Export all the scores. 546 ...

  • Technicolor - Thomson ST536 - page 566

    E-DOC-CTC- 20061027-0003 v2 .0 MLP Commands 544 mlp flush Flush all the Multi-Level acce ss Policies (MLP) structures. SYNT AX: mlp flush ...

  • Technicolor - Thomson ST536 - page 567

    E-DOC-CTC-20061 027-0003 v2.0 MLP Commands 545 mlp import Import all the scores. SYNT AX: where: RELA TED COMMANDS: mlp import [trace = <{disabled | enabled | full}>] trace Select the impo rt trace level. Choose between: > disabled > enabled > full. The default is disabled . OPTIONAL mlp debug export Export all the scores. ...

  • Technicolor - Thomson ST536 - page 568

    E-DOC-CTC- 20061027-0003 v2 .0 MLP Commands 546 mlp debug export Export all the scores. SYNT AX: RELA TED COMMANDS: mlp debug export mlp import Import all the scores. ...

  • Technicolor - Thomson ST536 - page 569

    E-DOC-CTC-20061 027-0003 v2.0 MLP Commands 547 mlp debug stats Display MLP statistics. SYNT AX: EXAMPLE: mlp debug stats =>mlp debug stats Roles (cur/free/max) : 8/7/15 Privileges (cur/free/max) : 35/25/60 ListItems (cur/free/max) : 31/119/150 => ...

  • Technicolor - Thomson ST536 - page 570

    E-DOC-CTC- 20061027-0003 v2 .0 MLP Commands 548 mlp debug traceconfig Modify the MLP trace settings. SYNT AX: where: EXAMPLE: mlp debug traceconfig [trace = <{disabled | enabled | full}>] trace Selec t the trace level. Choose between: > disabled > enabled > full. The default is disabled . OPTIONAL =>mlp debug traceconfig mlp trace ...

  • Technicolor - Thomson ST536 - page 571

    E-DOC-CTC-20061 027-0003 v2.0 MLP Commands 549 mlp privilege add Add a privilege. SYNT AX: where: mlp privilege add name = <quoted string> type = <{access | service}> [descr = <quoted string>] name The name of the new privilege. Note The maximum number of privileges is 60. REQUIRED type Select the privilege type. Choose between: & ...

  • Technicolor - Thomson ST536 - page 572

    E-DOC-CTC- 20061027-0003 v2 .0 MLP Commands 550 EXAMPLE: RELA TED COMMANDS: =>mlp privilege list type=access Privilege (type) Description ---------------------------- anyaccess (access) All access privileges granted AP1 (access) LAN_Local_all AP2 (access) LAN_Local with all secured channels AP3 (access) LAN_Local with all channels & access t ...

  • Technicolor - Thomson ST536 - page 573

    E-DOC-CTC-20061 027-0003 v2.0 MLP Commands 551 mlp privilege addzone Add a zone to a privilege. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: i Only one zone can b e added at a time to a priv ilege. If multiple zo nes need to be added, the command :mlp privileg e addzone must be executed for each zone to be added. mlp privilege addzone name = <str ...

  • Technicolor - Thomson ST536 - page 574

    E-DOC-CTC- 20061027-0003 v2 .0 MLP Commands 552 mlp privilege config Modify a privilege. SYNT AX: where: EXAMPLE: mlp privilege config name = <string> [descr = <quoted string>] [score = <{hex-word}[:{hex-word}] ex: 'a12:c30f'>] name The name of the privilege to b e modified. REQU IRED descr Set the privilege description. ...

  • Technicolor - Thomson ST536 - page 575

    E-DOC-CTC-20061 027-0003 v2.0 MLP Commands 553 mlp privilege delete Delete a privilege. SYNT AX: where: EXAMPLE: mlp privilege delete name = <string> name The name of the privil ege to b e deleted. R EQUIRED =>mlp privilege list type=access Privilege (type) Description ---------------------------- anyaccess (access) All access privileges g ...

  • Technicolor - Thomson ST536 - page 576

    E-DOC-CTC- 20061027-0003 v2 .0 MLP Commands 554 RELA TED COMMANDS: mlp privilege delete Add a privilege. mlp privilege list Display the privileges. ...

  • Technicolor - Thomson ST536 - page 577

    E-DOC-CTC-20061 027-0003 v2.0 MLP Commands 555 mlp privilege list Display the priv ileges. SYNT AX: where: mlp privilege list [name = <string>] [type = <{access | service}>] [verbose = <{minimal | medium | all}>] name The name of the privilege to b e listed. Note If not specified, all the p rivileges will be shown . OPTIONAL type ...

  • Technicolor - Thomson ST536 - page 578

    E-DOC-CTC- 20061027-0003 v2 .0 MLP Commands 556 EXAMPLE: RELA TED COMMANDS: =>mlp privilege list type=service Privilege (type) Description ---------------------------- anyservice (service) All service privileges granted SP1 (service) Limited_Read SP2 (service) detailed_Read SP3 (service) Write_to_LAN SP4 (service) Write_FWD_RT_normal_FW_cfgs SP5 ...

  • Technicolor - Thomson ST536 - page 579

    E-DOC-CTC-20061 027-0003 v2.0 MLP Commands 557 mlp privilege removezone Remove a zone from a privilege. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: i Only one zone can be removed at a time from a priv ilege. If multiple zones n eed to be removed, the command :mlp privileg e removezone must be executed for each zone to be removed. mlp privilege remo ...

  • Technicolor - Thomson ST536 - page 580

    E-DOC-CTC- 20061027-0003 v2 .0 MLP Commands 558 mlp role add Add a role. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: mlp role add name = <quoted string> parent = <string> [descr = <quoted string>] name The name of the new ro le. Note The maximum number of r oles is 15. REQUIRED parent The name of the parent role. REQUIRED descr Th ...

  • Technicolor - Thomson ST536 - page 581

    E-DOC-CTC-20061 027-0003 v2.0 MLP Commands 559 mlp role list Display the roles. ...

  • Technicolor - Thomson ST536 - page 582

    E-DOC-CTC- 20061027-0003 v2 .0 MLP Commands 560 mlp role addpriv Add a privilege to a role. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: mlp role addpriv name = <string> access = <string> service = <string> name The name of the role. REQUIRED access The nam e of the access privilege to be added. REQUIRED service The name of the ser ...

  • Technicolor - Thomson ST536 - page 583

    E-DOC-CTC-20061 027-0003 v2.0 MLP Commands 561 mlp role config Modify the role. SYNT AX: where: EXAMPLE: mlp role config name = <string> [parent = <string>] [descr = <quoted string>] name The name of the role to be configured. REQUIRED parent The name of the parent role. OPTIONAL descr The role description. Note The maximum length ...

  • Technicolor - Thomson ST536 - page 584

    E-DOC-CTC- 20061027-0003 v2 .0 MLP Commands 562 mlp role delete Delete a role. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: mlp role delete name = <string> name The name of the role to be deleted. REQUIRED =>mlp role list Role (parent) Description ------------------------- root (-) The superuser SuperUser (root) Any service and any access f ...

  • Technicolor - Thomson ST536 - page 585

    E-DOC-CTC-20061 027-0003 v2.0 MLP Commands 563 mlp role list Display the roles. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: mlp role list [name = <string>] [verbose = <{minimal | medium | all}>] name The name of the role to be listed. Note If not specified, all the ro les will be listed. OPTIONAL verbose Limit the output list. Choose be ...

  • Technicolor - Thomson ST536 - page 586

    E-DOC-CTC- 20061027-0003 v2 .0 MLP Commands 564 mlp role removepriv Remove a privilege from a role. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: mlp role removepriv name = <string> access = <string> [service = <string>] name The name of the role. REQUIRED access The name of the access pr ivilege to be deleted. REQUIRED service The ...

  • Technicolor - Thomson ST536 - page 587

    E-DOC-CTC-20061 027-0003 v2.0 NAT Commands 565 29 NA T Commands Introduction This chapter describes the commands of the nat comman d group. Contents This chapter covers th e following commands: nat config Display/modify gl obal NA T configuration op tions. 566 nat flush Flush the current NA T configuration. 567 nat ifconfig Modify addres s translat ...

  • Technicolor - Thomson ST536 - page 588

    E-DOC-CTC- 20061027-0003 v2 .0 NAT Commands 566 nat config Display/modif y global NA T configuration optio ns. SYNT AX: where: EXAMPLE: nat config [trace = <{disabled | enabled}>] trace Enable or disable traces. The default is disabled . REQUIRED =>nat config NAT traces : disabled =>nat config trace=enabled =>nat config NAT traces : ...

  • Technicolor - Thomson ST536 - page 589

    E-DOC-CTC-20061 027-0003 v2.0 NAT Commands 567 nat flush Flush the curren t NA T configuration. SYNT AX: nat flush ...

  • Technicolor - Thomson ST536 - page 590

    E-DOC-CTC- 20061027-0003 v2 .0 NAT Commands 568 nat ifconfig Modify address translation on an IP interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: nat ifconfig intf = <string> translation = <{disabled | enabled | trans- parent}> intf The IP interface name. REQUIRED translation Enable or disa ble address translation. Choose between: ...

  • Technicolor - Thomson ST536 - page 591

    E-DOC-CTC-20061 027-0003 v2.0 NAT Commands 569 nat iflist Display the address translation co nfiguration on all the interfaces. SYNT AX: EXAMPLE: RELA TED COMMANDS: nat iflist =>nat iflist Interface NAT loop disabled Internet enabled RtPPPoE_ppp enabled LocalNetwork transparent => nat ifconfig Modify address transla tio n on an IP interfac e. ...

  • Technicolor - Thomson ST536 - page 592

    E-DOC-CTC- 20061027-0003 v2 .0 NAT Commands 570 nat mapadd Add an address mapp ing to a Network Addr ess T ranslation (NA T) enabled interface. SYNT AX: where: nat mapadd intf = <string> [type = <{napt | nat}>] [outside_addr = <ip-range>] [inside_addr = <ip-range>] [access_list = <ip-range>] [foreign_addr = <ip-rang ...

  • Technicolor - Thomson ST536 - page 593

    E-DOC-CTC-20061 027-0003 v2.0 NAT Commands 571 inside_addr The inside (typi cally pr ivate) IP address. > Inbound: Represents the address(es ) to be used as destination address after translation. > Outbound: Thi s map will only apply if the so urce IP address is part of the inside address(es). Allowed values are: > An IP address (A.B.C.D o ...

  • Technicolor - Thomson ST536 - page 594

    E-DOC-CTC- 20061027-0003 v2 .0 NAT Commands 572 outside_port The outside port number or range (only for maps of type napt ). > For a NAPT map: Represents the range of TCP/UDP ports to be used as dynamic port ra nge during the NAPT process. > For a port-shifting map: Repr esen ts the source port(s) to be translated (shifted) into inside_port . ...

  • Technicolor - Thomson ST536 - page 595

    E-DOC-CTC-20061 027-0003 v2.0 NAT Commands 573 EXAMPLE: RELA TED COMMANDS: =>nat maplist Idx Type Interface Outside Address Inside Address Use 1 NAPT eth0 any:80 127.0.0.1:8080 0 2 NAPT eth0 any:1080 127.0.0.1:8080 0 3 NAPT eth0 any:8080 127.0.0.1:8080 0 =>nat mapadd intf=myPPP_ppp type=napt outside_addr=100.100.100.1 access_list=10.0.0.0/24 ...

  • Technicolor - Thomson ST536 - page 596

    E-DOC-CTC- 20061027-0003 v2 .0 NAT Commands 574 nat mapdelete Delete an address mapping from a NA T enabled interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: nat mapdelete intf = <string> index = <number> intf The IP interface name. REQUIRED index The map ind ex. Ti p Use the command :nat ma plist to obtain a list of the mapindexe ...

  • Technicolor - Thomson ST536 - page 597

    E-DOC-CTC-20061 027-0003 v2.0 NAT Commands 575 nat maplist Display the address mapping for a NA T enabled interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: nat maplist [intf = <string>] [expand = <{disabled | enabled}>] [string = <string>] [beginstring = <string>] intf The IP in terface name. Note If not specified, the ...

  • Technicolor - Thomson ST536 - page 598

    E-DOC-CTC- 20061027-0003 v2 .0 NAT Commands 576 nat tmpladd Add an address mapp ing template. SYNT AX: where: nat tmpladd [intf = <string>] [group = <{wan|local|lan|tunnel|dmz|guest} or number>] [timeout = <number{0-65535}>] [type = <{napt | nat}>] outside_addr = <ip-range> [inside_addr = <ip-range>] [access_list ...

  • Technicolor - Thomson ST536 - page 599

    E-DOC-CTC-20061 027-0003 v2.0 NAT Commands 577 outside_addr The outside (typ ically public) IP ad dress. > Inbound: This map will only apply if the destination IP address is part of the outside address(es). > Outbound: Represe nts the address(es) to be used as sour ce address after translation. Allowed values are: > An IP address (A.B.C.D ...

  • Technicolor - Thomson ST536 - page 600

    E-DOC-CTC- 20061027-0003 v2 .0 NAT Commands 578 protocol The IP protocol to be used as filter for inb ound/outbound traffi c. The NA T map only applies if the pr otocol of t he IP packet matches the map protocol . Select an IP proto col (see “ Supported IP Pro tocols” on page 74 6 ) or , alternativ ely , type the protoc ol number . The defaul t ...

  • Technicolor - Thomson ST536 - page 601

    E-DOC-CTC-20061 027-0003 v2.0 NAT Commands 579 EXAMPLE: RELA TED COMMANDS: =>nat tmpladd intf=myPPP_ppp type=napt outside_addr=100.100.100.1 =>nat tmpllist Idx Type Interface Ifgroup Outside Address Inside Address Use 1 NAPT myPPP_ppp any 100.100.100.1 unmapped 0 =>nat tmpladd group=lan type=napt outside_addr=100.200.100.1 =>nat tmpllis ...

  • Technicolor - Thomson ST536 - page 602

    E-DOC-CTC- 20061027-0003 v2 .0 NAT Commands 580 nat tmpldelete Delete an address mapping template. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: nat tmpldelete index = <number> index The index of the address ma pping template to be deleted. Ti p Use the command :nat tm pllist to view the address mapping templates. REQUIRED =>nat tmpllist Idx ...

  • Technicolor - Thomson ST536 - page 603

    E-DOC-CTC-20061 027-0003 v2.0 NAT Commands 581 nat tmpllist Display the address mapping templates. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: nat tmpllist [expand = <{disabled | enabled}>] expand Enable or disabl e expanded listing . The default is disabled . OP TIONAL =>nat tmpllist Idx Type Interface Ifgroup Outside Address Inside Addre ...

  • Technicolor - Thomson ST536 - page 604

    E-DOC-CTC- 20061027-0003 v2 .0 NAT Commands 582 nat tmplinst Instantiate address mappin g templates fo r a given dy namic address. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: nat tmplinst intf = <string> addr_index = <ip-address> dynamic_addr = <ip-address> intf The IP interface name. REQUIRED addr_index The outside IP address ind ...

  • Technicolor - Thomson ST536 - page 605

    E-DOC-CTC-20061 027-0003 v2.0 PPP Commands 583 30 PPP Commands Introduction This chapter describes the commands of the ppp comman d group. Contents This chapter covers th e following commands: ppp flush Flush all PPP in terfaces. 584 ppp ifadd Create a new PPP inter face. 585 ppp ifattach Attach a PPP interface. 587 ppp ifconfig Configure a PPP int ...

  • Technicolor - Thomson ST536 - page 606

    E-DOC-CTC- 20061027-0003 v2 .0 PPP Commands 584 ppp flush Flush all PPP interfaces. SYNT AX: i The flush command do es not impact previously save d configuration s. ppp flush ...

  • Technicolor - Thomson ST536 - page 607

    E-DOC-CTC-20061 027-0003 v2.0 PPP Commands 585 ppp ifadd Create a new PPP interface. SYNT AX: where: EXAMPLE: ppp ifadd intf = <string> intf The name for the new PPP interface. Note If not specified, th e destination parameter mus t be specified. In this case the name of the destination will do uble as interface name. REQUIRED =>ppp iflist ...

  • Technicolor - Thomson ST536 - page 608

    E-DOC-CTC- 20061027-0003 v2 .0 PPP Commands 586 RELA TED COMMANDS: ppp ifdelete Delete a PPP interface. ppp iflist Display the PPP interfaces. ...

  • Technicolor - Thomson ST536 - page 609

    E-DOC-CTC-20061 027-0003 v2.0 PPP Commands 587 ppp ifattach Attach a PPP interface. SYNT AX: where: ppp ifattach intf = <string> intf The name of the PPP interface to be attached. REQUIRED ...

  • Technicolor - Thomson ST536 - page 610

    E-DOC-CTC- 20061027-0003 v2 .0 PPP Commands 588 EXAMPLE: RELA TED COMMANDS: =>ppp iflist Internet: dest : RELAY [00:00:00] Retry : 10 mode = IP routing flags = echo magic accomp restart mru addr savepwd demanddial dns metric = 0 mru = 1492 Tx inactivity = 1200s left = 0s auth = auto user = password = admin state = down oper state = down link sta ...

  • Technicolor - Thomson ST536 - page 611

    E-DOC-CTC-20061 027-0003 v2.0 PPP Commands 589 ppp ifconfig Configure a PPP interface. SYNT AX: where: i The interface to be configured must not be connected at the time of configuration. If this should be the case, use the command :p pp ifdetach before usin g the command :ppp ifconfi g. ppp ifconfig intf = <string> [dest = <string>] [u ...

  • Technicolor - Thomson ST536 - page 612

    E-DOC-CTC- 20061027-0003 v2 .0 PPP Commands 590 password The password for remote P AP/CHAP authentication. OPTIONAL acname The Access Concentr ator name for a PPPoE session. Ti p Use the command :ppp ifscan to obtain the names of available access concentrators, if any . OP TIONAL servicename The Servi ce Name for a PPPoE session. Ti p Use the comma ...

  • Technicolor - Thomson ST536 - page 613

    E-DOC-CTC-20061 027-0003 v2.0 PPP Commands 591 silent Do not send anything at startup and just li sten for incoming LCP messages (enabled) or retry up to 10 times to establish the connection (disabled). The default is disabled . OP TIONAL echo Send LCP echo requests at regular intervals (enabled) or not (disabled). The default is disabled . OP TION ...

  • Technicolor - Thomson ST536 - page 614

    E-DOC-CTC- 20061027-0003 v2 .0 PPP Commands 592 dnsmetric A number between 1 and 100. Represents the DNS route metric to be used for the negotiated DNS servers. The default is 1 . OP TIONAL idletime A number between 0 and 10000 00 (seconds). Represents the maxi mum time the link may be idle. The default is 0 . OP TIONAL idletrigger Consider the lin ...

  • Technicolor - Thomson ST536 - page 615

    E-DOC-CTC-20061 027-0003 v2.0 PPP Commands 593 EXAMPLE: =>ppp iflist Internet: dest : RELAY [00:00:00] Retry : 10 mode = IP routing flags = echo magic accomp restart mru addr savepwd demanddial dns metric = 0 mru = 1492 Tx inactivity = 1200s left = 0s auth = auto user = password = admin state = down oper state = down link state = not-connected L ...

  • Technicolor - Thomson ST536 - page 616

    E-DOC-CTC- 20061027-0003 v2 .0 PPP Commands 594 ppp ifdelete Delete a PPP interfa ce. SYNT AX: where: EXAMPLE: ppp ifdelete intf = <intfname> intf The name of the PPP interface to be deleted. REQUIRED =>ppp iflist Internet: dest : RELAY [00:00:00] Retry : 10 mode = IP routing flags = echo magic accomp restart mru addr savepwd demanddial dn ...

  • Technicolor - Thomson ST536 - page 617

    E-DOC-CTC-20061 027-0003 v2.0 PPP Commands 595 RELA TED COMMANDS: ppp ifadd Create a new PPP interface. ppp iflist Display the PPP interfaces. ...

  • Technicolor - Thomson ST536 - page 618

    E-DOC-CTC- 20061027-0003 v2 .0 PPP Commands 596 ppp ifdetach Detach a PPP interface. SYNT AX: where: ppp ifdetach intf = <intfname> intf The name of the PPP interface to be detached . REQUIRED ...

  • Technicolor - Thomson ST536 - page 619

    E-DOC-CTC-20061 027-0003 v2.0 PPP Commands 597 EXAMPLE: RELA TED COMMANDS: =>ppp iflist Internet: dest : RELAY [00:00:00] Retry : 10 mode = IP routing flags = echo magic accomp restart mru addr savepwd demanddial dns metric = 0 mru = 1492 Tx inactivity = 1200s left = 0s auth = auto user = password = admin state = down oper state = down link stat ...

  • Technicolor - Thomson ST536 - page 620

    E-DOC-CTC- 20061027-0003 v2 .0 PPP Commands 598 ppp iflist Display the PPP interfaces. SYNT AX: where: EXAMPLE INPUT/OUTPUT : RELA TED COMMANDS: ppp iflist [intf = <intfname>] [string = <string>] [beginstring = <string>] intf The name of the PPP interface. Note If not specified , all PPP interfaces are shown . OP TIONAL string str ...

  • Technicolor - Thomson ST536 - page 621

    E-DOC-CTC-20061 027-0003 v2.0 PPP Commands 599 ppp ifscan Scan a PPPoE interface fo r available Access Concentrator a nd Service names. SYNT AX: where: EXAMPLE: i Use the command :ppp ifdeta ch for this in terface before performing a scan on it. ppp ifscan intf = <string> [time = <number{0-36000}>] intf The name of the P PPoE interface ...

  • Technicolor - Thomson ST536 - page 622

    E-DOC-CTC- 20061027-0003 v2 .0 PPP Commands 600 ppp rtadd Add a route to the routing table when the PPP link comes up. This route configurati on will determine wh ich local host s are allowed to use this li nk and/or which remote destinations should be or should not be reachable. SYNT AX: where: i The interface mu st not be connected when a route c ...

  • Technicolor - Thomson ST536 - page 623

    E-DOC-CTC-20061 027-0003 v2.0 PPP Commands 601 EXAMPLE: RELA TED COMMANDS: metric The route metric, in other wo rd s, the cost fac tor of the route. Practically , the cost is de termined by the hop count. OP TIONAL =>ppp iflist Internet: dest : RELAY [00:00:00] Retry : 10 mode = IP routing flags = echo magic accomp restart mru addr savepwd deman ...

  • Technicolor - Thomson ST536 - page 624

    E-DOC-CTC- 20061027-0003 v2 .0 PPP Commands 602 ppp rtdelete Delete the route for a PPP link. SYNT AX: where: i The interface must not be connected when a route configuration m u st be deleted. If the interface is connected, use the command :ppp ifde tach for this interface. ppp rtdelete intf = <intfname> intf The PPP interface name for which ...

  • Technicolor - Thomson ST536 - page 625

    E-DOC-CTC-20061 027-0003 v2.0 PPP Commands 603 EXAMPLE: RELA TED COMMANDS: =>ppp iflist Internet: dest : RELAY [00:00:00] Retry : 10 mode = IP routing flags = echo magic accomp restart mru addr savepwd demanddial dns metric = 0 mru = 1492 Tx inactivity = 1200s left = 0s auth = auto user = password = admin state = down oper state = down link stat ...

  • Technicolor - Thomson ST536 - page 626

    E-DOC-CTC- 20061027-0003 v2 .0 PPP Commands 604 ppp relay flush Remove all Ethernet interfaces from the PPP relay agent list and terminate all sessions. SYNT AX: i The flush command do es not impact previously save d configuration s. ppp relay flush ...

  • Technicolor - Thomson ST536 - page 627

    E-DOC-CTC-20061 027-0003 v2.0 PPP Commands 605 ppp relay ifadd Add an Ethernet interfac e to the PPP relay list. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ppp relay ifadd intf = <string> intf The Ethernet interf ace to be added to the PPP relay agent list. REQUIRED =>ppp relay iflist # Interface HWaddr Status 1 ethoa_0_35 00-0e-50-0f-fc- ...

  • Technicolor - Thomson ST536 - page 628

    E-DOC-CTC- 20061027-0003 v2 .0 PPP Commands 606 ppp relay ifconfig Modify an ethernet interface from the PPP relay agent list. SYNT AX: where: ppp relay ifconfig intf = <string> hwaddr = <hardware-address> inft The ethernet intf to be adde d to the PPP relay agent l ist. REQUIRED hwaddr The hardware address (e.g. Ethernet MAC address) o ...

  • Technicolor - Thomson ST536 - page 629

    E-DOC-CTC-20061 027-0003 v2.0 PPP Commands 607 ppp relay ifdelete Delete an Ethernet interface from the PPP relay agent list. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ppp relay ifdelete intf = <string> intf The Ethernet in terface to be delete d from the PPP relay agent list. REQUIRED =>ppp relay iflist # Interface HWaddr Status 1 ethoa ...

  • Technicolor - Thomson ST536 - page 630

    E-DOC-CTC- 20061027-0003 v2 .0 PPP Commands 608 ppp relay iflist Display all Ethernet interfaces ad ded to the PPP relay agent list. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ppp relay iflist intf The Ethernet interf ace to be added to the PPP relay agent list. REQUIRED =>ppp relay iflist # Interface HWaddr Status 1 ethoa_0_35 00-0e-50-0f-fc-2 ...

  • Technicolor - Thomson ST536 - page 631

    E-DOC-CTC-20061 027-0003 v2.0 PPP Commands 609 ppp relay sesslist Add an Ethernet interfac e to the PPP relay list. SYNT AX: where: ppp relay ifadd intf = <string> intf The Ethernet interf ace to be added to the PPP relay agent list. REQUIRED ...

  • Technicolor - Thomson ST536 - page 632

    E-DOC-CTC- 20061027-0003 v2 .0 PPP Commands 610 ...

  • Technicolor - Thomson ST536 - page 633

    E-DOC-CTC-20061 027-0003 v2.0 PPTP Commands 611 31 PPTP Commands Introduction This chapter describes the commands of the pptp command group. Contents This chapter covers th e following commands: pptp ifadd Add a Point-to-Point T unnelin g Protocol (PP TP) profile. 612 pptp flush Flush the com plete PPTP configuration. 613 pptp list Show the current ...

  • Technicolor - Thomson ST536 - page 634

    E-DOC-CTC- 20061027-0003 v2 .0 PPTP Commands 612 pptp ifadd Add a Point-to-Point T unneling Protocol (PP TP) profile. SYNT AX: where: i Backwards compatible wi th previous release, us e profiles instead. pptp ifadd dest = <string> [rate = <number{10-10000}>] [encaps = <{vcmux | nlpid}>] [ac = <{never | always | keep}>] dest ...

  • Technicolor - Thomson ST536 - page 635

    E-DOC-CTC-20061 027-0003 v2.0 PPTP Commands 613 pptp flush Flush the complete P PTP configuration. SYNT AX: i The flush command does not impact previously saved configurations. pptp flush ...

  • Technicolor - Thomson ST536 - page 636

    E-DOC-CTC- 20061027-0003 v2 .0 PPTP Commands 614 pptp list Show the current PP TP configuration. SYNT AX: EXAMPLE: pptp list =>pptp list Dialstr Destination QoS Encaps AC State User DIALUP_PPP3 default vcmux never CONNECTED (10.0.0.2) => ...

  • Technicolor - Thomson ST536 - page 637

    E-DOC-CTC-20061 027-0003 v2.0 PPTP Commands 615 pptp profadd Define a new PP TP profile. SYNT AX: where: EXAMPLE: pptp profadd name = <string> [qos = <string>] [encaps = <{vcmux | nlpid}>] [ac = <{never | always | keep}>] name Th e name of the new PP TP profile. REQUIRED qos The name of the qosbook entry , containing the set ...

  • Technicolor - Thomson ST536 - page 638

    E-DOC-CTC- 20061027-0003 v2 .0 PPTP Commands 616 RELA TED COMMANDS: pptp profdelete Define a new PP TP profile. pptp proflist Display all the curre nt PP TP profiles. ...

  • Technicolor - Thomson ST536 - page 639

    E-DOC-CTC-20061 027-0003 v2.0 PPTP Commands 617 pptp profdelete Delete a PPTP profile. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: pptp profdelete name <string> name Th e name of the PP TP prof ile to be deleted. REQUIRED =>pptp proflist Profile QoS Encaps AC Relay_PPP1 default nlpid always PPTPLink default vcmux never =>pptp profdelete ...

  • Technicolor - Thomson ST536 - page 640

    E-DOC-CTC- 20061027-0003 v2 .0 PPTP Commands 618 pptp proflist Display all the current PP TP profiles. SYNT AX: EXAMPLE: RELA TED COMMANDS: pptp proflist =>pptp proflist Profile QoS Encaps AC Relay_PPP1 default nlpid always PPTPLink default vcmux never => pptp profadd Define a new PP TP profile. pptp profdelete Delete a PPTP pro file. ...

  • Technicolor - Thomson ST536 - page 641

    E-DOC-CTC-20061 027-0003 v2.0 Script Commands 619 32 Script Commands Introduction This chapter describes the commands of the script command group. Scripting is not a g eneral purpose mechan ism but is only used in the autoPVC/ILMI m echanism. Contents This chapter covers th e following commands: ! It is recommended no t to change the defa ult scrip ...

  • Technicolor - Thomson ST536 - page 642

    E-DOC-CTC- 20061027-0003 v2 .0 Script Commands 620 script add Add a line to a script. SYNT AX: where: RELA TED COMMANDS: script add name = <string> [index = <number>] command = <quoted string> name Name of the script in which a line must be added. REQUIRED index Line number Note Use 0 to add a line . OP TIONAL command Comma nd. RE ...

  • Technicolor - Thomson ST536 - page 643

    E-DOC-CTC-20061 027-0003 v2.0 Script Commands 621 script delete Delete a complete script or a line from a script. SYNT AX: where: RELA TED COMMANDS: script delete name = <string> [index = <number>] name Name of the script to be deleted. REQUIRED index Line number to be deleted. Ti p Use the command :scrip t list to view the line numbers ...

  • Technicolor - Thomson ST536 - page 644

    E-DOC-CTC- 20061027-0003 v2 .0 Script Commands 622 script flush Flush all scripts. SYNT AX: i The flush command does not impa ct previously saved configurations. script flush ...

  • Technicolor - Thomson ST536 - page 645

    E-DOC-CTC-20061 027-0003 v2.0 Script Commands 623 script list Display a script or all scripts. SYNT AX: where: EXAMPLE Some of the default scripts are shown below: script list [name = <string>] name Name of the script to be listed. Note If not specified, all th e scripts are displayed. OP TIONAL =>script list Script: autopvc_add_qos 0: qos ...

  • Technicolor - Thomson ST536 - page 646

    E-DOC-CTC- 20061027-0003 v2 .0 Script Commands 624 RELA TED COMMANDS: script add Add a line to a scr ipt. script delete Delete a complete script or a line from a script. ...

  • Technicolor - Thomson ST536 - page 647

    E-DOC-CTC-20061 027-0003 v2.0 Script Commands 625 script run Run a script. SYNT AX: where: script run name = <string> pars = <string> name Name of the script to be run. Ti p Use the command :scrip t list to obtain the names of the different scripts. REQUIRED pars Parameters sepa rated with comma. For example a,b,c. REQUIRED ...

  • Technicolor - Thomson ST536 - page 648

    E-DOC-CTC- 20061027-0003 v2 .0 Script Commands 626 ...

  • Technicolor - Thomson ST536 - page 649

    E-DOC-CTC-20061 027-0003 v2.0 Service Commands 627 33 Service Commands Introduction This chapter describes the commands of the servic e command group. Contents This chapter covers th e following commands: service host assign Assign a service t o a host device. 628 service host config Modify and/or display glob al service configuration options. 629 ...

  • Technicolor - Thomson ST536 - page 650

    E-DOC-CTC- 20061027-0003 v2 .0 Service Commands 628 service host assign Assign a service to a host device. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: service host assign name = <quoted string> [host = <ip-address>] [log = <{disabled|enabled}>] name The name of an existing host service. REQUIRED host The IP address of the host. OP ...

  • Technicolor - Thomson ST536 - page 651

    E-DOC-CTC-20061 027-0003 v2.0 Service Commands 629 service host config Modify and/ or display global service configuration optio ns. SYNT AX: where: EXAMPLE: service host config [trace = <{disabled | enabled}>] trace Enable or disable traces. The default is disabled . REQUIRED =>service host config Service traces : disabled l=> ...

  • Technicolor - Thomson ST536 - page 652

    E-DOC-CTC- 20061027-0003 v2 .0 Service Commands 630 service host add Add a host service. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: service host add name = <quoted string> [mode = <{server | client | custom}>] name The name of th e ne w host service. REQUIRED mode The service mode. Choose between: > server : The service is defined f ...

  • Technicolor - Thomson ST536 - page 653

    E-DOC-CTC-20061 027-0003 v2.0 Service Commands 631 service host delete Delete a host service . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: service host delete name = <quoted string> name The name of th e host se rvice to be deleted. REQUIRED =>service host list Service Name Host User-Defined Mode ------------------------------------------- ...

  • Technicolor - Thomson ST536 - page 654

    E-DOC-CTC- 20061027-0003 v2 .0 Service Commands 632 service host disable Disable a host service. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: service host disable [name = <quoted string>] name The name of th e host service to be disabled. Note If not specified, all the h ost services will be di sabled. OP TIONAL =>service host list Service ...

  • Technicolor - Thomson ST536 - page 655

    E-DOC-CTC-20061 027-0003 v2.0 Service Commands 633 service host flush Flush all host services. SYNT AX: service host flush ...

  • Technicolor - Thomson ST536 - page 656

    E-DOC-CTC- 20061027-0003 v2 .0 Service Commands 634 service host list Display a list of host services. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: service host list [name = <quoted string>] [string = <string>] [beginstring = <string>] name The name of th e host service to be listed . Note If not specified, all the h ost services w ...

  • Technicolor - Thomson ST536 - page 657

    E-DOC-CTC-20061 027-0003 v2.0 Service Commands 635 service host stats Show the host service statistics. SYNT AX: EXAMPLE: service host stats =>service host stats Services : 113 of 150 in use. Service maps : 225 of 300 in use. Trigger ports: 0 of 25 in use. => ...

  • Technicolor - Thomson ST536 - page 658

    E-DOC-CTC- 20061027-0003 v2 .0 Service Commands 636 service host triggerlist List all triggers. SYNT AX: EXAMPLE: service host triggerlist =>service triggerlist Ip Triggerport Portrange Timeout -- ----------- --------- ------- => ...

  • Technicolor - Thomson ST536 - page 659

    E-DOC-CTC-20061 027-0003 v2.0 Service Commands 637 service host rule add Create/define a host service portmap. SYNT AX: where: RELA TED COMMANDS: service host rule add name = <quoted string> [protocol = <{any|tcp|udp} or number>] [baseport = <supported UDP port | number>] portrange = <port-range> [triggerport = <supported ...

  • Technicolor - Thomson ST536 - page 660

    E-DOC-CTC- 20061027-0003 v2 .0 Service Commands 638 service host rule delete Delete a host service portmap. SYNT AX: where: RELA TED COMMANDS: service host rule delete name = <quoted string> [protocol = <{any|tcp|udp} or number>] [baseport = <supported UDP port | number>] portrange = <port-range> [triggerport = <supported ...

  • Technicolor - Thomson ST536 - page 661

    E-DOC-CTC-20061 027-0003 v2.0 Service Commands 639 service sy stem ifadd Add an interface grou p to the access list. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: service system ifadd name = <string> group = <{wan|local|lan|tunnel|dmz|guest} or number> name The name of th e system serv ice for this access list. REQUIRED group The interfac ...

  • Technicolor - Thomson ST536 - page 662

    E-DOC-CTC- 20061027-0003 v2 .0 Service Commands 640 service sy stem ifdelete Delete an interface group from the access list. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: service system ifdelete name = <string> group = <{wan|local|lan|tunnel|dmz|guest} or number> name The name of th e system serv ice for this access list. REQUIRED group T ...

  • Technicolor - Thomson ST536 - page 663

    E-DOC-CTC-20061 027-0003 v2.0 Service Commands 641 service sy stem ipadd Add an IP address (ran ge) to the access list. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: service system ipadd name = <string> ip = <ip-range> name The name of th e system serv ice for this access list. REQUIRED ip The IP address (range) fo r this access list. REQ ...

  • Technicolor - Thomson ST536 - page 664

    E-DOC-CTC- 20061027-0003 v2 .0 Service Commands 642 service sy stem ipdelete Delete an IP address (r ange) from the access list. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: service system ipdelete name = <string> ip = <ip-range> name The name of th e system serv ice for this access list. REQUIRED ip The IP address (range) fo r this acce ...

  • Technicolor - Thomson ST536 - page 665

    E-DOC-CTC-20061 027-0003 v2.0 Service Commands 643 service sy stem list Display the system services. SYNT AX: where: service system list [name = <string>] [expand = <{disabled | enabled}>] [dynamics = <{disabled | enabled}>] [members = <{disabled | enabled}>] [string = <string>] [beginstring = <string>] name The ...

  • Technicolor - Thomson ST536 - page 666

    E-DOC-CTC- 20061027-0003 v2 .0 Service Commands 644 EXAMPLE: RELA TED COMMANDS: =>service system list Idx Name Protocol SrcPort DstPort Group State --------------------------------------------------------------------------------- 1 DNS-C udp 53 enabled 2 SNTP udp 123 123 enabled 3 SLA_ICMP_PING icmp 8 enabled 4 SLA_UDP_PING udp 7 enabled 5 SLA_I ...

  • Technicolor - Thomson ST536 - page 667

    E-DOC-CTC-20061 027-0003 v2.0 Service Commands 645 service sy stem mapadd Add a port map for a system service. SYNT AX: where: RELA TED COMMANDS: service system mapadd name = <{string}> intf = <{auto|loop|Internet|LocalNetwork}> port = <supported port or number> name The name of the system service for this map. REQUIRED intf The i ...

  • Technicolor - Thomson ST536 - page 668

    E-DOC-CTC- 20061027-0003 v2 .0 Service Commands 646 service sy stem mapdelete Delete a port map fo r a system service. SYNT AX: where: RELA TED COMMANDS: service system mapdelete name = <string> intf = <{auto|loop|Internet|LocalNetwork}> port = <supported port or number> name The name of the system service for this map. REQUIRED i ...

  • Technicolor - Thomson ST536 - page 669

    E-DOC-CTC-20061 027-0003 v2.0 Service Commands 647 service sy stem modify Modify a system service. SYNT AX: where: RELA TED COMMANDS: service system modify name = <string> [state = <{disabled | enabled}>] [port = <supported port or number>] [srcintf = <string>] [log = <{disabled|enabled}>] [qoslabel = <{None|DSCP|In ...

  • Technicolor - Thomson ST536 - page 670

    E-DOC-CTC- 20061027-0003 v2 .0 Service Commands 648 ...

  • Technicolor - Thomson ST536 - page 671

    E-DOC-CTC-20061 027-0003 v2.0 SNMP Commands 649 34 SNMP Commands Introduction This chapter describes the commands of the snmp command group. Contents This chapter covers th e following commands: snmp config Show/s et global Simple Network Management Protocol (SNMP) parameters. 650 snmp get Get from the supplied SNMP Object IDentifier (OID). 651 snm ...

  • Technicolor - Thomson ST536 - page 672

    E-DOC-CTC- 20061027-0003 v2 .0 SNMP Commands 650 snmp config Show/set glob al Simple Networ k Mana gement Protocol (SNMP) parameters. SYNT AX: where: EXAMPLE: snmp config [sysContact = <quoted string>] [sysName = <quoted string>] [sysLocation = <quoted string>] sysContact The SNMP system contact. The defaul t is Service Pro v ider ...

  • Technicolor - Thomson ST536 - page 673

    E-DOC-CTC-20061 027-0003 v2.0 SNMP Commands 651 snmp get Get from the supplied SN MP Object IDentifier (OID) . For example: get ObjectId=.1.3.6.1.2.1.1.1.0. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: snmp get [ObjectId = <string>] ObjectID The Object Iden tifier . Object ID to get from ... mu st include the instance which is 0 for sca lar ob ...

  • Technicolor - Thomson ST536 - page 674

    E-DOC-CTC- 20061027-0003 v2 .0 SNMP Commands 652 snmp getnext GetNext from the supplied SN MP OID. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: snmp getnext [ObjectId = <string>] ObjectID The Object Identifier . Object ID to getnext from for example .1.3.6.1.2.1.1 system returns sysDescription. OP TIONAL =>snmp getnext ObjectId=.1.3.6.1.2.1 ...

  • Technicolor - Thomson ST536 - page 675

    E-DOC-CTC-20061 027-0003 v2.0 SNMP Commands 653 snmp walk W alk from the supplied SNMP OID. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: snmp walk [ObjectId = <string>] ObjectID The Object Identifier . Object ID to walk from fo r exam ple .1.3.6.1 .2.1.1 system walks the system group. OP TIONAL =>snmp walk ObjectId=.1.3.6.1.2.1.1 VB_octetSt ...

  • Technicolor - Thomson ST536 - page 676

    E-DOC-CTC- 20061027-0003 v2 .0 SNMP Commands 654 snmp community add Configure an SNMP com munity string to allow SNMP access over IP . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: snmp community add securityname = <{RWCommunity | ROCommunity}> communityname = <password> securityname Configure access rights/res trictions control for the c ...

  • Technicolor - Thomson ST536 - page 677

    E-DOC-CTC-20061 027-0003 v2.0 SNMP Commands 655 snmp community delete Delete an SNMP commun ity string to prevent SNMP access over IP . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: snmp community delete securityname = <{RWCommunity | ROCommunity}> securityname Select the a ccess rights/restrictions co ntrol for the community name to be deleted ...

  • Technicolor - Thomson ST536 - page 678

    E-DOC-CTC- 20061027-0003 v2 .0 SNMP Commands 656 snmp community list List all SNMP co mmunity strings in use fo r SNMP access over IP . SYNT AX: EXAMPLE: RELA TED COMMANDS: snmp community list =>snmp community list Read-write SNMP community name : ***** Read-only SNMP community name : ***** => snmp community add Configure an SNMP community st ...

  • Technicolor - Thomson ST536 - page 679

    E-DOC-CTC-20061 027-0003 v2.0 SNMP Commands 657 snmp community modify Modify an SNMP community string to allow SNMP access over IP . SYNT AX: where: snmp community modify securityname = <{RWCommunity | ROCommunity}> communityname = <password> securityname Configure access rights/res trictions control for the community name. Choose betwe ...

  • Technicolor - Thomson ST536 - page 680

    E-DOC-CTC- 20061027-0003 v2 .0 SNMP Commands 658 snmp ifadd Create a new SNMP interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: snmp ifadd intf = <string> dest = <string> intf The name for the new SNMP interface. REQUIRED dest T he destination interface for this SNMP i nterface. REQUIRED =>snmp ifadd intf = new dest = Internet : ...

  • Technicolor - Thomson ST536 - page 681

    E-DOC-CTC-20061 027-0003 v2.0 SNMP Commands 659 snmp ifdelete Delete an SNMP interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: snmp ifdelete intf = <string> intf The name of the SNMP interf ace. REQUIRED =>snmp ifdelete intf = new :snmp ifdelete intf=new => snmp ifadd Create a new SNMP interface. snmp ifattach Attach an SNMP interf ...

  • Technicolor - Thomson ST536 - page 682

    E-DOC-CTC- 20061027-0003 v2 .0 SNMP Commands 660 snmp ifattach Attach an SNMP interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: snmp ifattach intf = <string> intf The name of the SNMP interface. REQUIRED =>snmp ifattach intf = Internet :snmp ifattach intf=Internet => snmp ifadd Create a new SNMP interface. snmp ifdelete Delete an S ...

  • Technicolor - Thomson ST536 - page 683

    E-DOC-CTC-20061 027-0003 v2.0 SNMP Commands 661 snmp ifdetach Detach an SNMP interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: snmp ifdetach intf = <string> intf The name of the SNMP interf ace. REQUIRED =>snmp ifdetach intf = Internet :snmp ifdetach intf=Internet => snmp ifadd Create a new SNMP interface. snmp ifdelete Delete an S ...

  • Technicolor - Thomson ST536 - page 684

    E-DOC-CTC- 20061027-0003 v2 .0 SNMP Commands 662 snmp ifconfig Modify an SNMP interfac e. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: snmp ifconfig intf = <string> [securityname = <{RWCommunity | ROCommunity}>] [communityname = <password>] intf The name of the SNMP in terface to configu re. REQU IRED securityname Configure access ...

  • Technicolor - Thomson ST536 - page 685

    E-DOC-CTC-20061 027-0003 v2.0 SNMP Commands 663 snmp iflist Display the SNMP interfaces. SYNT AX: where: snmp iflist [intf = <string>] intf The name of an SNMP interface to configu re. O PTI ONAL ...

  • Technicolor - Thomson ST536 - page 686

    E-DOC-CTC- 20061027-0003 v2 .0 SNMP Commands 664 ...

  • Technicolor - Thomson ST536 - page 687

    E-DOC-CTC-20061 027-0003 v2.0 SNTP Commands 665 35 SNTP Commands Introduction This chapter describes the com mands of the Simple N etwork T ime Protocol (SNTP) command grou p. Contents This chapter covers th e following commands: sntp add Add a Network T ime Protocol (NTP ) server to the NT P server list. 666 sntp config Modify/display the SNTP cli ...

  • Technicolor - Thomson ST536 - page 688

    E-DOC-CTC- 20061027-0003 v2 .0 SNTP Commands 666 sntp add Add a Network T ime Protocol (NTP ) server to the NTP server list. The internal Thom son ST real time clock (SNTP cl ient) will be synchronized with th e NTP server . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: sntp add [addr = <ip-address>] [name = <string>] [version = <numbe ...

  • Technicolor - Thomson ST536 - page 689

    E-DOC-CTC-20061 027-0003 v2.0 SNTP Commands 667 sntp config Modify/disp lay the SNTP client config uration. SYNT AX: where: EXAMPLE: sntp config [state = <{enabled | disabled}>] [poll = <number{1-60}>] [pollpresync = <number{1-60}>] state Enab le or disable the Thomson ST SNTP cli ent. The default is enabled . OP TIONAL poll A num ...

  • Technicolor - Thomson ST536 - page 690

    E-DOC-CTC- 20061027-0003 v2 .0 SNTP Commands 668 sntp delete Delete an NTP server fr om the NTP s erver list. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: sntp delete [addr = <ip-address>] [name = <string>] addr The IP addr ess of the NTP serv er to be removed from the list. Note This parameter is optional in this respect that either an ...

  • Technicolor - Thomson ST536 - page 691

    E-DOC-CTC-20061 027-0003 v2.0 SNTP Commands 669 sntp flush Flush the NTP server list and the SNTP client configuratio n. SYNT AX: sntp flush ...

  • Technicolor - Thomson ST536 - page 692

    E-DOC-CTC- 20061027-0003 v2 .0 SNTP Commands 670 sntp list List the NTP servers. SYNT AX: EXAMPLE: DESCRIPTION: The status of an NTP server can be: > Not used : The Thomso n ST SNTP client is disabled. As a consequence , none of the NTP servers are used. > Contacting... : The Thomson ST SNTP client is trying to contact this NTP server . > ...

  • Technicolor - Thomson ST536 - page 693

    E-DOC-CTC-20061 027-0003 v2.0 Software Commands 671 36 Software Commands Introduction This chapter describes the commands of the softwa re command grou p. Contents This chapter covers th e following commands: software upgrade Reboot the mo dem to init iate the SW upgrade. 672 software version Display the software version. 673 ...

  • Technicolor - Thomson ST536 - page 694

    E-DOC-CTC- 20061027-0003 v2 .0 Software Commands 672 software upgrade Reboot the modem to initiate the SW upgrade. New software available on a remote LAN host w ill be uploa ded to the modem. SYNT AX: software upgrade ...

  • Technicolor - Thomson ST536 - page 695

    E-DOC-CTC-20061 027-0003 v2.0 Software Commands 673 software version Display the software version. SYNT AX: software version ...

  • Technicolor - Thomson ST536 - page 696

    E-DOC-CTC- 20061027-0003 v2 .0 Software Commands 674 ...

  • Technicolor - Thomson ST536 - page 697

    E-DOC-CTC-20061 027-0003 v2.0 System Commands 675 37 Sy stem Commands Introduction This chapter describes the commands of the system command group. Contents This chapter covers th e following commands: system config Set/change the system co nfig uration parameter s. 676 system flush Flush the current system configuration. 678 system locale Set/get ...

  • Technicolor - Thomson ST536 - page 698

    E-DOC-CTC- 20061027-0003 v2 .0 System Commands 676 sy stem config Set/change the system co nfiguration pa rameters. SYNT AX: where: ! For a good operation o f UPnP and the discovery mechanism, it is hig hly recommended not to change the system co nfiguration settings. system config [upnp = <{disabled | enabled}>] [tr64 = <{disabled | enabl ...

  • Technicolor - Thomson ST536 - page 699

    E-DOC-CTC-20061 027-0003 v2.0 System Commands 677 EXAMPLE: autosavedelay A number between 0 and 600. Represents the autosave de lay in seconds (0 for immediate save). OP TIONAL =>system config upnp discovery : enabled TR-64 discovery : disabled mdap discovery : enabled drst support : disabled reset button : enabled digest authentication : enable ...

  • Technicolor - Thomson ST536 - page 700

    E-DOC-CTC- 20061027-0003 v2 .0 System Commands 678 sy stem flush Flush the curren t system configuration. The system password and the system config settings (dca che excluded) are flushed. SYNT AX: EXAMPLE: i The flush comman d does not impact previously saved configuratio ns. system flush =>system flush Security notification: Password changed, ...

  • Technicolor - Thomson ST536 - page 701

    E-DOC-CTC-20061 027-0003 v2.0 System Commands 679 sy stem locale Set/get the regional settings. SYNT AX: where: system locale [dec_symbol = <{, | .}>] [group_symbol = <{. | ,}>] [date_separator = <{/ | - | .}>] [date_format = <{iso | ddmmyyyy | ddmmyy | mmddyyyy | mmddyy}>] [time_format = <{iso | hmmss}>] [datetime_for ...

  • Technicolor - Thomson ST536 - page 702

    E-DOC-CTC- 20061027-0003 v2 .0 System Commands 680 EXAMPLE: time_format Set the time format. Choose betwe en: > iso > hmmss. The default is iso . Note h = hour s; mm = mi nutes; ss = seconds. OP TIONAL datetime_format Set th e date-time format. Choose betwe en: > iso > date+time > time+dat e. The default is date+time . OP TIONAL dura ...

  • Technicolor - Thomson ST536 - page 703

    E-DOC-CTC-20061 027-0003 v2.0 System Commands 681 sy stem reboot Reboot the Thomso n ST. SYNT AX: EXAMPLE: RELA TED COMMANDS: ! Non-saved configur ation settings will be lost after reboot. system reboot =>system reboot ..... (lost session connectivity due to reboot) ..... system timedreb oot Set or change a tim ed reboot for the Thomson ST .. ...

  • Technicolor - Thomson ST536 - page 704

    E-DOC-CTC- 20061027-0003 v2 .0 System Commands 682 sy stem reset Reset the Thomson ST to its factory or ISP defaults and reboot the device. SYNT AX: where: EXAMPLE: ! All user specific settings and all saved configuration changes are lost after reboot. system reset factory yes/no = <{yes | no}> proceed no/yes = <{no | yes}> factory yes/ ...

  • Technicolor - Thomson ST536 - page 705

    E-DOC-CTC-20061 027-0003 v2.0 System Commands 683 RELA TED COMMANDS: sntp config Modify/display the SNTP client configuration. ...

  • Technicolor - Thomson ST536 - page 706

    E-DOC-CTC- 20061027-0003 v2 .0 System Commands 684 sy stem timedreboot Set or change a timed reboot for the Thomson ST. SYNT AX where: EXAMPLE: RELA TED COMMANDS: timedreboot [state = <{disabled|enabled}>] [time = <number{0-16384}>] [date = <string>] state Enable/Disable timed reboot. The default is disabled . OP TIONAL time Chang ...

  • Technicolor - Thomson ST536 - page 707

    E-DOC-CTC-20061 027-0003 v2.0 System Commands 685 sy stem debug autosave Autosave debugg ing commands SYNT AX: where: system debug autosave [trace = <{disabled|enabled}>] trace Enable or di sable autosave traces OP TIONAL ...

  • Technicolor - Thomson ST536 - page 708

    E-DOC-CTC- 20061027-0003 v2 .0 System Commands 686 sy stem debug stats Show the Thomson ST CP U and memory statistics. SYNT AX: where: DESCRIPTION: > CHIP memory : Memory used by the CPU (first MB from the RAM) – not cached since it has to be realtime. > Application memory : Memory used by the applications. > min : The least amou nt of f ...

  • Technicolor - Thomson ST536 - page 709

    E-DOC-CTC-20061 027-0003 v2.0 System Commands 687 sy stem ra config Configure Remote managem ent access parameters. SYNT AX: where: EXAMPLE: system ra config [secure = <{disabled | enabled}>] [port = <number>] [timeout = <number>] secure Enable or disabl e https. The default is enabled . OP TIONAL port Set the destinat ion port fo ...

  • Technicolor - Thomson ST536 - page 710

    E-DOC-CTC- 20061027-0003 v2 .0 System Commands 688 sy stem rtc synchronize Do a SNTP update and synchron ize the realtime clock. SYNT AX: system rtc synchro- nize ...

  • Technicolor - Thomson ST536 - page 711

    E-DOC-CTC-20061 027-0003 v2.0 System Commands 689 sy stem rtc settime Set/get date, time, ti mezone, daylig ht savings time, uptime. When synchronization with an exte rnal NTP server via the Thomson ST SNTP client fails, this com mand allows to manuall y configure its internal cl ock. SYNT AX: where: EXAMPLE: i In cases without regular synchroniz a ...

  • Technicolor - Thomson ST536 - page 712

    E-DOC-CTC- 20061027-0003 v2 .0 System Commands 690 ...

  • Technicolor - Thomson ST536 - page 713

    E-DOC-CTC-20061 027-0003 v2.0 Systemlog Commands 691 38 Sy stemlog Commands Introduction This chapter describes the commands of the system log command group. Contents This chapter covers th e following commands: systemlog flush Flush all messages in the inte rnal Syslog message buffer . 692 systemlog show Show me ssages in the inte rnal Sysl og me ...

  • Technicolor - Thomson ST536 - page 714

    E-DOC-CTC- 20061027-0003 v2 .0 Systemlog Commands 692 sy stemlog flush Flush all messages in the inte rnal Syslog message buffer . SYNT AX: systemlog flush ...

  • Technicolor - Thomson ST536 - page 715

    E-DOC-CTC-20061 027-0003 v2.0 Systemlog Commands 693 sy stemlog show Show messages in the intern al Syslog message buffer . SYNT AX: where: systemlog show [fac = <supported facility name>] [sev = <supported severity name>] [hist = <{disabled | enabled}>] fac Specify the facility name of the syslog messages to be shown. Use one of ...

  • Technicolor - Thomson ST536 - page 716

    E-DOC-CTC- 20061027-0003 v2 .0 Systemlog Commands 694 EXAMPLE: =>syslog msgbuf show fac=kern sev=emerg hist=enabled <0> SysUpTime: 14:45:43 KERNEL Controlled restart (after internal error or explicit system re boot) <0> SysUpTime: 02:58:18 KERNEL Controlled restart (after internal error or explicit system re boot) <0> SysUpTime ...

  • Technicolor - Thomson ST536 - page 717

    E-DOC-CTC-20061 027-0003 v2.0 Systemlog Commands 695 sy stemlog send Send messages from the inte rnal Syslog message buffer to a specifie d local or remote sy slog server host. SYNT AX: where: i There will be no no tification on whether the host h as received the messages or not. systemlog send [fac = <supported facility name>] [sev = <sup ...

  • Technicolor - Thomson ST536 - page 718

    E-DOC-CTC- 20061027-0003 v2 .0 Systemlog Commands 696 sy stemlog DBG dbg_sy slog Perform a syslog call. SYNT AX: where: systemlog DBG dbg_syslog priority = <number{0-191}> msgstring = <string> priority priority number msgstring message content ...

  • Technicolor - Thomson ST536 - page 719

    E-DOC-CTC-20061 027-0003 v2.0 Systemlog Commands 697 sy stemlog DBG dbg_long_mess Generate a long sy slog message call. SYNT AX: systemlog DBG dbg_long_mess ...

  • Technicolor - Thomson ST536 - page 720

    E-DOC-CTC- 20061027-0003 v2 .0 Systemlog Commands 698 sy stemlog DBG dbg_burst Perform a syslog message burst. SYNT AX: systemlog DBG dbg_burst ...

  • Technicolor - Thomson ST536 - page 721

    E-DOC-CTC-20061 027-0003 v2.0 Systemlog Commands 699 sy stemlog DBG dbg_contents Show the contents of the message buffer . SYNT AX: systemlog DBG dbg_contents ...

  • Technicolor - Thomson ST536 - page 722

    E-DOC-CTC- 20061027-0003 v2 .0 Systemlog Commands 700 ...

  • Technicolor - Thomson ST536 - page 723

    E-DOC-CTC-20061 027-0003 v2.0 Upgrade Commands 701 39 Upgrade Commands Introduction This chapter describes the commands of the upgrad e command group. Contents This chapter covers th e following commands: upgrade config Change the upgrade daemon con figuration. 702 upgrade start Start a new upgrad e. 703 upgrade debug traceconfig Enable/disable upg ...

  • Technicolor - Thomson ST536 - page 724

    E-DOC-CTC- 20061027-0003 v2 .0 Upgrade Commands 702 upgrade config Change the upgrade d aemon configuration. SYNT AX: where: EXAMPLE: upgrade config [state = <{disabled|enabled}>] [protocol = <{tftp|ftp|http|https}>] state Set the upgrade daemon st ate to enabled or disabled. The default is disabled . OP TIONAL protocol The transfer pro ...

  • Technicolor - Thomson ST536 - page 725

    E-DOC-CTC-20061 027-0003 v2.0 Upgrade Commands 703 upgrade start Start a new upgrade. SYNT AX: where: upgrade start protocol = <{tftp|ftp|http|https}> [server = <string>] [filename = <string>] protocol The protoco l to be used fo r the download. Choose between: > tftp > ftp > http > https The default is disabled . REQU ...

  • Technicolor - Thomson ST536 - page 726

    E-DOC-CTC- 20061027-0003 v2 .0 Upgrade Commands 704 upgrade debug traceconfig Enable/disable up grade daemon tracing. SYNT AX: where: upgrade debug traceconfig state = <{disabled|enabled}> state Set the upgared daemon state to enabled or disabled . REQUIRED ...

  • Technicolor - Thomson ST536 - page 727

    E-DOC-CTC-20061 027-0003 v2.0 Upgrade Commands 705 upgrade debug sesslist Display the list of sessions. SYNT AX: EXAMPLE: upgrade debug sesslist =>:upgrade debug sesslist Session 0: --------------------------------------------------------------- SessionId : 0x80c25850 State : IDLE Protocol : TFTP ServerName: FileName : DestFile : ServerIP : 0.0. ...

  • Technicolor - Thomson ST536 - page 728

    E-DOC-CTC- 20061027-0003 v2 .0 Upgrade Commands 706 upgrade profile add Add a new file profile description. SYNT AX: where: RELA TED COMMANDS: upgrade profile add extension = <{sts|ini}> [maxsize(KBytes) = <number>] action = <{none|config_load|script_load|reboot}> extension The extension of the new file profile. Choose between: &g ...

  • Technicolor - Thomson ST536 - page 729

    E-DOC-CTC-20061 027-0003 v2.0 Upgrade Commands 707 upgrade profile modify Modify a file profile desc ription. SYNT AX: where: RELA TED COMMANDS: upgrade profile modify extension = <{sts|ini}> [maxsize(KBytes) = <number>] action = <{none|config_load|script_load|reboot}> extension The extension of the new file profile. Choose betwee ...

  • Technicolor - Thomson ST536 - page 730

    E-DOC-CTC- 20061027-0003 v2 .0 Upgrade Commands 708 upgrade profile delete Delete a file profile description. SYNT AX: where: RELA TED COMMANDS: upgrade profile delete extension = <{sts|ini}> extension The extension of the profi le to be deleted. Choose between: > sts > ini REQUIRED upgrade profile add Add a new file profile descri ptio ...

  • Technicolor - Thomson ST536 - page 731

    E-DOC-CTC-20061 027-0003 v2.0 Upgrade Commands 709 upgrade profile list Display a list of the file profile descriptions. SYNT AX: RELA TED COMMANDS: upgrade profile list upgrade profile delete De lete a file profile descrip tion. upgrade profile modify Modify a file profile description. ...

  • Technicolor - Thomson ST536 - page 732

    E-DOC-CTC- 20061027-0003 v2 .0 Upgrade Commands 710 upgrade ifadd Add a download interface. SYNT AX: where: RELA TED COMMANDS: upgrade ifadd intf = <string> intf A download interface REQUIRED ...

  • Technicolor - Thomson ST536 - page 733

    E-DOC-CTC-20061 027-0003 v2.0 Upgrade Commands 711 upgrade ifattach Attach a download interface. SYNT AX: where: RELA TED COMMANDS: upgrade ifattach intf = <string> intf A download interface REQUIRED ...

  • Technicolor - Thomson ST536 - page 734

    E-DOC-CTC- 20061027-0003 v2 .0 Upgrade Commands 712 upgrade ifconfig Configure a download interface. SYNT AX: where: RELA TED COMMANDS: upgrade ifconfig intf = <string> [protocol = <{tftp|ftp|http|https}>] [dest = <{loop|Internet|ISDN_backup| ISDN_backup_trigger| lan1|wan1|dmz1|guest1}>] [server = <string>] [file = <strin ...

  • Technicolor - Thomson ST536 - page 735

    E-DOC-CTC-20061 027-0003 v2.0 Upgrade Commands 713 upgrade ifdelete Delete a download interface. SYNT AX: where: RELA TED COMMANDS: upgrade ifdelete intf = <string> intf A download interface REQUIRED ...

  • Technicolor - Thomson ST536 - page 736

    E-DOC-CTC- 20061027-0003 v2 .0 Upgrade Commands 714 upgrade ifdetach Detach a download interface. SYNT AX: where: RELA TED COMMANDS: upgrade ifdetach intf = <string> intf A download interface REQUIRED ...

  • Technicolor - Thomson ST536 - page 737

    E-DOC-CTC-20061 027-0003 v2.0 Upgrade Commands 715 upgrade iflist List all downlo ad interfaces. SYNT AX: RELA TED COMMANDS: upgrade iflist ...

  • Technicolor - Thomson ST536 - page 738

    E-DOC-CTC- 20061027-0003 v2 .0 Upgrade Commands 716 ...

  • Technicolor - Thomson ST536 - page 739

    E-DOC-CTC-20061 027-0003 v2.0 UPnP Commands 717 40 UPnP Commands Introduction This chapter describes the commands of the upnp command group. Contents This chapter covers th e following commands: upnp config Configure the UPnP™ parameter(s). 718 upnp flush Flush the UPnP™ con figuration. Th e UPnP configuration wil l be reset to the default conf ...

  • Technicolor - Thomson ST536 - page 740

    E-DOC-CTC- 20061027-0003 v2 .0 UPnP Commands 718 upnp config Configure the UPnP™ parameter(s). SYNT AX: where: upnp config [maxage = <number{60-999999}>] [writemode = <{full | natonly | readonly}>] [safenat = <{disabled | enabled}>] [preferredaddress = <ip-address>] [httpport = <number{1-65535}>] maxage A number betw ...

  • Technicolor - Thomson ST536 - page 741

    E-DOC-CTC-20061 027-0003 v2.0 UPnP Commands 719 upnp flush Flush the UPnP™ conf iguration. The UP nP configuratio n will be reset to the default configur ation. SYNT AX: upnp flush ...

  • Technicolor - Thomson ST536 - page 742

    E-DOC-CTC- 20061027-0003 v2 .0 UPnP Commands 720 upnp list List all registered devices. SYNT AX: where: EXAMPLE: i Use this command to check whether a PPP connection is properly configured and thus advertised as a PPP service. upnp list [verbose = <number{0-2}>] verbose V erbose level. The default is 1 . OP TIONAL =>upnp list ------------- ...

  • Technicolor - Thomson ST536 - page 743

    E-DOC-CTC-20061 027-0003 v2.0 User Commands 721 41 User Commands Introduction This chapter describes the commands of the user command group. Contents This chapter covers th e following commands: user add Add a user . 722 user config Modify a user . 724 user delete Delete a user . 726 user flush Flush the users. 727 user list Display the users. 728 ...

  • Technicolor - Thomson ST536 - page 744

    E-DOC-CTC- 20061027-0003 v2 .0 User Commands 722 user add Add a user . SYNT AX: where: i Y ou can only add a user whos e privileges are the same or l ower than your own privil eges. user add name = <quoted string> password = <password> role = <string> [hash2 = <string>] [descr = <quoted string>] [defuser = <{disable ...

  • Technicolor - Thomson ST536 - page 745

    E-DOC-CTC-20061 027-0003 v2.0 User Commands 723 EXAMPLE: In the examp le below , the user Adm i nistrator creates a new user JohnDoe. This user has lo wer access rights than the user “Poweruser”. DESCRIPTION: > U : indicates the default user . > R : indicates the default remote a dministrator . RELA TED COMMANDS: {Administrator}=>user ...

  • Technicolor - Thomson ST536 - page 746

    E-DOC-CTC- 20061027-0003 v2 .0 User Commands 724 user config Modify a user . SYNT AX: where: i Y ou can only modify a user whose privileges ar e the same or lower than your own privileges. user config name = <string> [password = <password>] [role = <string>] [descr = <quoted string>] [defuser = <{disabled | enabled}>] ...

  • Technicolor - Thomson ST536 - page 747

    E-DOC-CTC-20061 027-0003 v2.0 User Commands 725 EXAMPLE: {Superuser}=>user list User Role ==== ==== Superuser root aPoweruser Poweruser {Superuser}=>user config name=aPoweruser role=LAN_admin {Superuser}=>user list User Role ==== ==== Superuser root aPoweruser LAN_admin {Superuser}=> ...

  • Technicolor - Thomson ST536 - page 748

    E-DOC-CTC- 20061027-0003 v2 .0 User Commands 726 user delete Delete a user . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: i Y ou can only delete a user whose privileges ar e the same or lower than your o wn privileges. user delete name = <string> name The name of th e user to be deleted. REQUIRED {Administrator}=>user list User Flags Role - ...

  • Technicolor - Thomson ST536 - page 749

    E-DOC-CTC-20061 027-0003 v2.0 User Commands 727 user flush Flush the use rs. SYNT AX: EXAMPLE: When this T elnet session is termin ated and a new T e lnet session is in itiated, the follo wi ng welcome screen will appear: The user will not have to auth entic ate himself to gain access to th e Thomson ST. ! After execution of this command, the acces ...

  • Technicolor - Thomson ST536 - page 750

    E-DOC-CTC- 20061027-0003 v2 .0 User Commands 728 user list Display the users. SYNT AX: where: user list [name = <string>] [channel = <{ftp | telnet | http | mdap | serial}>] [origin = <{lan | wan | local}>] [secure = <{disabled | enabled}>] name The user name . Note If not specified, all the users will be listed. OP TIONAL c ...

  • Technicolor - Thomson ST536 - page 751

    E-DOC-CTC-20061 027-0003 v2.0 User Commands 729 EXAMPLE: RELA TED COMMANDS: {Administrator}=>user list User Flags Role ---- ----- ---- Administrator U Administrator tech R TechnicalSupport {Administrator}=>user list name=tech channel=http origin=wan service(s): r_lan, r_wan, r_fs_view, r_fs_retrieve, r_rtg, r_fwdg, r_nat, r_frwl, r_ipsec_norm ...

  • Technicolor - Thomson ST536 - page 752

    E-DOC-CTC- 20061027-0003 v2 .0 User Commands 730 user rights Display the session rights. SYNT AX: EXAMPLE: i The user rights of the curren tly logged-in user are shown. user rights {Administrator}=>user rights Current session info: user: name='Administrator', role='Administrator' access: lan (origin_lan), telnet (channel_teln ...

  • Technicolor - Thomson ST536 - page 753

    E-DOC-CTC-20061 027-0003 v2.0 Abbreviations 731 42 Abbreviations The table below lists all the abbreviatio ns used in the CLI Reference Guide. Abbreviation Description AAL5 A TM Ada ption Layer 5 ACL Access Control List ADSL Asymmetric Digital Subscriber Line AES Advanced Encryption System AF Assured Forwarding AP Access Point ARP Address Resoluti ...

  • Technicolor - Thomson ST536 - page 754

    E-DOC-CTC- 20061027-0003 v2 .0 Abbreviations 732 HTTP HyperT ext T ransfer Protocol ICMP Internet Control M essage Protocol IDS Intrusion Detection System IGD Internet Gateway Device IGMP Internet Group Manag ement Protocol IKE Internet Key Exchange IP Internet Protocol IP oA IP over A TM IPCP Internet Protocol Co ntrol Protocol IPSec IP Security I ...

  • Technicolor - Thomson ST536 - page 755

    E-DOC-CTC-20061 027-0003 v2.0 Abbreviations 733 PPPoA PPP over A TM PPPoE PPP over Ethernet PPTP Point-to-Point T u nneling Protocol PSD Power Spectral Densi ty PSK Pre-Shared Key PVC Permanent Virtual Channel QoS Quality of Service RIP Routing Informa tion Protocol RTC Real T ime Clock RTT Round T rip T ime SAs Security Associations SF TP Secure F ...

  • Technicolor - Thomson ST536 - page 756

    E-DOC-CTC- 20061027-0003 v2 .0 Abbreviations 734 VLSM V ariable Length Subnet Masking VP Vir t ua l P at h VPI V irtual Path Identifier VPN Virtual Private Networking WA N Wide Area Network WDS Wireless Distribution System WEP Wired Equivalent Pr ivacy WFQ W eighted Fair Queueing WINS Windows Internet Naming Service WLAN Wireless LAN WP A Wi-Fi Pro ...

  • Technicolor - Thomson ST536 - page 757

    E-DOC-CTC-20061 027-0003 v2.0 System Logging Messages 735 43 Sy stem Logging Messages Introduction This chapter lists the differe nt System Logging messages. Contents This chapter lists the different System Logging messages of the following modu les: Auto-PVC Module 736 Configuration Module 736 DHCP Client Module 736 DHCP Relay Module 737 DHCP Serv ...

  • Technicolor - Thomson ST536 - page 758

    E-DOC-CTC- 20061027-0003 v2 .0 System Logging Messages 736 Auto-PVC Module Configuration Module DHCP Client Module Facility Severity Contents LOCAL5 W ARNING AUTOPVC scrip t <script_name> failed LOCAL5 WA R N I N G AUTOPVC script <script_name> failed LOCAL5 W ARNING AUTOPVC script <script_ name> (name1, qosb_name) failed LOCAL5 WA ...

  • Technicolor - Thomson ST536 - page 759

    E-DOC-CTC-20061 027-0003 v2.0 System Logging Messages 737 DHCP Relay Module DHCP Server Module Facility Severity Contents LOCAL2 W ARNING DHCR relay: D ropping boot rq s on interface <intf_id> du e to invalid giaddr for server (<ip-address>) LOCAL2 WA R N I N G DHCR rel ay: Dropping boot rep ly with invalid rela y agent option from < ...

  • Technicolor - Thomson ST536 - page 760

    E-DOC-CTC- 20061027-0003 v2 .0 System Logging Messages 738 Dyndns Module Firewall Module Facility Severity Contents DYNDNS W ARNING <DYNDNS_ STR_ID> Connection failed to <dynd ns_service> for client <dyndns_client> DYNDNS WA R NI N G <DYNDNS_ STR_ID> Failed to resolv e host name <dyndns_service> for client <dyndns_c ...

  • Technicolor - Thomson ST536 - page 761

    E-DOC-CTC-20061 027-0003 v2.0 System Logging Messages 739 LOGIN Module Kernel Module Linestate Module NAPT Module Facility Severity Contents AUTH NOTI CE LOG OUT User <user_i d> logged o ut on <conne ction_type> (<ip-add ress>) AUTH NOTICE LOGOUT User <user_id> logged out on <conne ction_type> AUTH NOTICE LOGOUT <se ...

  • Technicolor - Thomson ST536 - page 762

    E-DOC-CTC- 20061027-0003 v2 .0 System Logging Messages 740 PPP Module PPTP Module Facility Severity Contents LOCAL0 W ARNING PPP Link u p (<intf name>) LOCAL0 WA R N I N G PP P Link down (<intf name>) AUTH ERROR PPP P AP authentication faile d (<intf name>) [protocol reject] AUTH INFO PPP P AP on intf <intf_id> no re sponse ...

  • Technicolor - Thomson ST536 - page 763

    E-DOC-CTC-20061 027-0003 v2.0 System Logging Messages 741 RIP Module Facility Severity Contents LOCAL1 INFO RIP Packet received from unk nown interface LOCAL1 INFO RIP Packet size is sma ller than mini mum size LOCAL1 INFO RIP Packet size is greater than maximum size LOCAL1 INFO RIP W rong RIP packet ali gnment LOCAL1 INFO RIP RIP version 0 with co ...

  • Technicolor - Thomson ST536 - page 764

    E-DOC-CTC- 20061027-0003 v2 .0 System Logging Messages 742 Routing Module Session Module SNTP Module LOCAL1 I NFO RIP IP Address <ip-address> not found in RIP tabl e Facility Severity Contents LOCAL1 INFO GRP Default desti nation is routed via ga teway <ip_address > LOCAL1 INFO GRP Default destination is not rout ed anymore via gateway ...

  • Technicolor - Thomson ST536 - page 765

    E-DOC-CTC-20061 027-0003 v2.0 System Logging Messages 743 Software Module UPnP Module Facility Severity Contents KERN INFO SOF TW ARE File <Filename> <r eceive || transmit> initiated KERN INFO SOF TW ARE File <Filename> <r ec eive || transmit><““ || not> successful terminated" Facility Severity Contents W ARNI ...

  • Technicolor - Thomson ST536 - page 766

    E-DOC-CTC- 20061027-0003 v2 .0 System Logging Messages 744 ...

  • Technicolor - Thomson ST536 - page 767

    E-DOC-CTC-20061 027-0003 v2.0 Supported Key Names 745 44 Supported Key Names Contents This chapter lists all the key names supported by the Thomson ST, tha t can be used for completi ng CLI command parame ters: Supported IP Pr otocols 746 Supported TCP/ UDP Port Names 747 Supported I CMP T ype Nam es 750 Supported Faciliti es 751 Supported Severi t ...

  • Technicolor - Thomson ST536 - page 768

    E-DOC-CTC- 20061027-0003 v2 .0 Supported Key Names 746 Supported IP Protocols For more information on the listed IP protocols, see RFC1340 or www.iana.org. Protocol name Number Description ah 51 Authentication Header (AH) egp 8 Exterior Gateway Protocol (EGP) esp 50 Encapsul ating Security Pa yload (ESP) ggp 3 Gateway Gateway Protocol (GGP) gre 47 ...

  • Technicolor - Thomson ST536 - page 769

    E-DOC-CTC-20061 027-0003 v2.0 Supported Key Names 747 Supported TCP/UDP Port Names For more informati on on the listed TCP/UDP po rt assignments, see RFC1340 or www .iana.org. Port name Number TCP UDP Description echo 7 Y Y Echo discard 9 Y Y Discard systat 11 Y Y Active Users daytime 13 Y Y Daytime qotd 17 Y Y Quote of the Day chargen 19 Y Y Chara ...

  • Technicolor - Thomson ST536 - page 770

    E-DOC-CTC- 20061027-0003 v2 .0 Supported Key Names 748 sntp 123 Y Y Simple Network T ime Protocol (SNTP) ingres-net 134 Y Y INGRES -NET Service netbios-ns 137 Y Y NE TBIOS Naming System netbios-dgm 138 Y Y NETBIOS Datagram Service netbios-ssn 139 Y Y NETBIOS Session Service imap2 143 Y Y Internet Message Access Protocol (IMAP) v2 sql-net 150 Y Y SQ ...

  • Technicolor - Thomson ST536 - page 771

    E-DOC-CTC-20061 027-0003 v2.0 Supported Key Names 749 ntalk 518 Y Y NT alk utime 519 Y Y UNIX T ime rip 520 - Y Local routing process (on site); uses variant of Xerox NS Routing Information Proto col (RIP) timed 525 Y Y T i meserver netwall 533 Y Y For emer gency broadcasts new-rwho 540 Y Y uucpd remote who is uucp 540 Y Y uucpd uucp-rlogi n 540 Y ...

  • Technicolor - Thomson ST536 - page 772

    E-DOC-CTC- 20061027-0003 v2 .0 Supported Key Names 750 Supported ICMP T ype Names For more information on the listed ICMP type names, see RFC1340 or www .iana.org. ICMP T ype name Number Description echo-reply 0 Echo Reply destination-unreachable 3 Destination Unreachable source-quench 4 Source Quench redirect 5 Redirect echo-request 8 Echo router- ...

  • Technicolor - Thomson ST536 - page 773

    E-DOC-CTC-20061 027-0003 v2.0 Supported Key Names 751 Supported Facilities For more information on the listed facilities, see RFC3164. Facilty Name Hierarchy Code Syslog facility (listed accor ding descending importance) kern 0 Kernel messages user 8 User-level messages mail 16 Mail system daemon 24 System daemons auth 32 Authorization messages sys ...

  • Technicolor - Thomson ST536 - page 774

    E-DOC-CTC- 20061027-0003 v2 .0 Supported Key Names 752 Supported Severities For more information on the li sted severities, see RFC3164. IP Precedence Severity Name Hierarchy Code Syslog severity (listed according descending importance) emerg 0 Emergency condit ions, system unusable alert 1 Alert conditions, immedi ate action is required crit 2 Cri ...

  • Technicolor - Thomson ST536 - page 775

    E-DOC-CTC-20061 027-0003 v2.0 Supported Key Names 753 Differentiated Services Code Point (DSCP) For more information on DSCP , see RFC3260. PHB PHB Name Binary value ef Expe dited Forwarding 101110 af41 Assured Forwardi ng 41 100110 af42 Assured Forwarding 42 100100 af43 Assured Forwardi ng 43 100010 af31 Assured Forwarding 31 011110 af32 Assured F ...

  • Technicolor - Thomson ST536 - page 776

    E-DOC-CTC- 20061027-0003 v2 .0 Supported Key Names 754 ...

  • Technicolor - Thomson ST536 - page 777

    Index E-DOC-CTC-20061 027-0003 v2.0 755 A aal5stats atm debug aal5stats 41 actlist eth bridge dynvlan actlist 265 add atm bundle add 27 atm oam vclb add 52 atm phonebook add 55 atm qosbook add 60 dhcp client rqoptions add 122 dhcp client txopt ions add 126 dhcp rela y add 130 dhcp rule add 143 dhcp server lease add 155 dhcp server pool add 168 dns ...

  • Technicolor - Thomson ST536 - page 778

    Index E-DOC-CTC-2006 1027-0003 v2.0 756 add 55 autolist 56 delete 57 flush 58 list 59 qosbook add 60 config 61 ctdadd 62 ctddelete 64 ctdlist 65 delete 66 flush 67 list 68 attach atm bundle attach 28 autolist atm phonebook autolist 56 autopvc config 70 info 72 autosave system debug autosave 685 B bind connection bind 86 bindlist connection bindli s ...

  • Technicolor - Thomson ST536 - page 779

    Index E-DOC-CTC-20061 027-0003 v2.0 757 service host config 629 snmp config 650 sntp config 667 system config 676 system ra config 687 upgrade config 702 upnp config 718 user config 724 connection appconfig 82 appinfo 84 applist 85 bind 86 bindlist 87 clean 88 clear 89 config 90 debug 91 describe 92 flush 93 info 94 list 95 refresh 96 stats 97 time ...

  • Technicolor - Thomson ST536 - page 780

    Index E-DOC-CTC-2006 1027-0003 v2.0 758 optionlist 125 txoptions add 126 delete 127 list 128 relay add 130 config 133 debug stats 131 traceconfig 132 delete 134 flush 135 ifconfig 136 iflist 138 list 139 modify 140 ruleadd 141 ruledelete 142 rule add 143 debug traceconfig 144 delete 145 flush 146 list 147 server config 148 debug clear 151 stats 152 ...

  • Technicolor - Thomson ST536 - page 781

    Index E-DOC-CTC-20061 027-0003 v2.0 759 delete 221 flush 222 list 223 modify 224 dump config dump 75 dyndns add 228 delete 229 flush 230 host add 234 delete 235 flush 236 list 237 list 231 modify 232 service list 238 modify 240 E egress eth switch mirror egress 308 env flush 244 get 245 list 246 set 247 unset 248 eth bridge add 261 clear 259 config ...

  • Technicolor - Thomson ST536 - page 782

    Index E-DOC-CTC-2006 1027-0003 v2.0 760 iflist 322 vlan add 323 delete 324 flush 325 list 326 exec debug exec 106 mbus client exec 519 export mlp debug ex port 546 expr add 328 delete 332 flush 334 list 335 modify 339 F firewall chain add 349 delete 351 flush 353 list 354 config 344 debug clear 355 stats 356 traceconfig 357 flush 346 level add 358 ...

  • Technicolor - Thomson ST536 - page 783

    Index E-DOC-CTC-20061 027-0003 v2.0 761 G get env get 245 snmp get 651 snmp getnext 652 getaddress dns server debug spoof getaddress 195 getflags dns server debug spoof getflags 196 grouplist igmp proxy grouplis t 420 grp config 376 flush 377 rip config 379 flush 382 ifconfig 383 show 385 rtlist 378 gstats atm debug gstats 42 H hostmgr add 388 clea ...

  • Technicolor - Thomson ST536 - page 784

    Index E-DOC-CTC-2006 1027-0003 v2.0 762 atm ifdelete 24 dhcp client ifdelete 113 eth bridge ifdelete 276 eth bridge vlan ifdelete 299 eth ifdelete 255 ip auto ifdelete 464 ip ifdelete 443 ppp ifdelete 5 94 ppp relay ifde lete 607 service system ifdelete 640 snmp ifdelete 659 ifdetach atm ifdetach 25 dhcp client ifdetach 114 eth bridge ifdetach 277 ...

  • Technicolor - Thomson ST536 - page 785

    Index E-DOC-CTC-20061 027-0003 v2.0 763 iflist 445 ifwait 446 ipadd 447 ipconfig 448 ipdelete 449 iplist 450 mcast flush 454 rtadd 451 rtdelete 452 rtlist 453 rtadd 455 rtdelete 457 rtlist 458 ipadd ip ipadd 44 7 service system ipadd 641 ipconfig ip ipconfig 448 ipdelete ip ipdelete 449 service system ipdelete 642 iplist ip iplist 450 ipqos config ...

  • Technicolor - Thomson ST536 - page 786

    Index E-DOC-CTC-2006 1027-0003 v2.0 764 eth switch qos list 316 eth switch share list 312 eth vlan list 326 expr list 335 firewall chain list 354 firewall level li st 361 firewall list 347 firewall rule list 367 hostmgr list 394 ids list 398 ids pattern list 402 ids signature list 404 ids threshold list 407 igmp host list 412 interface list 428 ipq ...

  • Technicolor - Thomson ST536 - page 787

    Index E-DOC-CTC-20061 027-0003 v2.0 765 list 555 removezone 557 role add 558 addpriv 560 config 561 delete 562 list 563 removepriv 564 modify atm oam cc modify 50 atm oam modify 46 dhcp rela y modify 140 dsd urlfilter rule modify 224 dyndns modify 232 dyndns service modi fy 240 expr modify 339 firewall level modify 362 firewall rule modify 369 ids ...

  • Technicolor - Thomson ST536 - page 788

    Index E-DOC-CTC-2006 1027-0003 v2.0 766 profdelete pptp profdelete 617 proflist pptp proflist 618 proxy dsd debug proxy 213 R reboot system reboot 681 recycling dsd debug recycling 214 refresh connection refresh 96 register mbus client register 521 removepriv mlp role removep riv 564 removezone mlp privilege removezone 557 reset system reset 682 ri ...

  • Technicolor - Thomson ST536 - page 789

    Index E-DOC-CTC-20061 027-0003 v2.0 767 set env set 247 firewall level set 363 settime system rtc settime 689 show grp rip show 3 85 systemlog show 693 snmp community add 654 delete 655 list 656 modify 657 config 650 get 651 getnext 652 ifadd 658 ifattach 660 ifconfig 662 ifdelete 659 ifdetach 661 iflist 663 walk 653 sntp add 666 config 667 delete ...

  • Technicolor - Thomson ST536 - page 790

    Index E-DOC-CTC-2006 1027-0003 v2.0 768 nat tmpladd 576 tmpldelete dhcp server option tmpl delete 166 nat tmpldelete 580 tmplinst nat tmplinst 582 tmpllist dhcp server option tmpl list 167 nat tmpllist 581 traceconfig dhcp client debug traceconfig 121 dhcp relay debug traceconfig 132 dhcp rule debug traceconfig 144 dhcp server debug traceconfi g 15 ...

  • Technicolor - Thomson ST536 - page 791

    ...

  • Technicolor - Thomson ST536 - page 792

    THOMSON Telecom Belgium Prins Boudewijnlaan 47 2650 Edegem www .thomson-broadband.com © THOMSON . All right s reserved. E-DOC-CTC-20061027-0003 v2.0. ...

Manufacturer Technicolor - Thomson Category Network Router

Documents that we receive from a manufacturer of a Technicolor - Thomson ST536 can be divided into several groups. They are, among others:
- Technicolor - Thomson technical drawings
- ST536 manuals
- Technicolor - Thomson product data sheets
- information booklets
- or energy labels Technicolor - Thomson ST536
All of them are important, but the most important information from the point of view of use of the device are in the user manual Technicolor - Thomson ST536.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Technicolor - Thomson ST536, service manual, brief instructions and user manuals Technicolor - Thomson ST536. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Technicolor - Thomson ST536.

Similar manuals

A complete manual for the device Technicolor - Thomson ST536, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Technicolor - Thomson ST536 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Technicolor - Thomson ST536.

A complete Technicolor - Thomson manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Technicolor - Thomson ST536 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Technicolor - Thomson ST536, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Technicolor - Thomson ST536, that we can find in the current document
3. Tips how to use the basic functions of the device Technicolor - Thomson ST536 - which should help us in our first steps of using Technicolor - Thomson ST536
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Technicolor - Thomson ST536
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Technicolor - Thomson ST536 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Technicolor - Thomson ST536?

Use the form below

If you did not solve your problem by using a manual Technicolor - Thomson ST536, ask a question using the form below. If a user had a similar problem with Technicolor - Thomson ST536 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)