-
Miele DA3060 - page 1
Operating and installation instructions Cooker hood DA 3060 To avoid the risk of accidents or damage to this appliance, it is essential to read these instructions before it is installed and used for the first time. M.-Nr. 07 773 930 e n-G B ...
-
Miele DA3060 - page 2
Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Description of the functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Guide to the app ...
-
Miele DA3060 - page 3
Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal, and should be recycled. Packaging e.g. cling film, polystyrene and plastic wrappings must be kept out of the reach of babies and young children. Danger of suffocation! Disposal of your old appliance ...
-
Miele DA3060 - page 4
This appliance complies with all relevant local and national safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before using it for the first time. They contain important information on the safety, i ...
-
Miele DA3060 - page 5
Technical safety ~ Before installation, check the cooker hood for visible signs of damage. Under no circumstances should you use a damaged appliance. A damaged appliance is dangerous. ~ Before connecting the appliance to the mains supply, make sure that the voltage and frequency details given on the data plate correspond with the on-site electricit ...
-
Miele DA3060 - page 6
~ Do not connect the appliance to the mains electricity supply by a multi-socket unit or an extension lead. These do not guarantee the required safety of the appliance (e.g. danger of overheating). ~ This appliance must not be used in a non-stationary location (e.g. on a ship). ~ In areas which may be subject to infestation by cockroaches or other ...
-
Miele DA3060 - page 7
In order to ensure safe operation, and to prevent gases given off by the heating appliances from being drawn back into the room when the cooker hood and the heater are in operation simultaneously, an underpressure of 0.04 mbar (4 pa) is the maximum permissible in the room. Ventilation can be maintained by air inlets which must not be blocked, in wi ...
-
Miele DA3060 - page 8
~ The filters should be regularly cleaned or changed as appropriate. Saturated filters are a fire hazard. See "Cleaning and care". ~ The cooker hood can get very hot during cooking due to heat rising from the hob. Do not touch the housing or the grease filters until the cooker hood has cooled down. ~ Do not use a steam-cleaner to clean th ...
-
Miele DA3060 - page 9
The cooker hood works with . . . air extraction: The air is drawn in, cleaned by the grease filter and then directed outside. If the on-site ventilation system does not have a non-return flap , then the non-return flap supplied with the appliance must be fitted in the exhaust socket in the motor unit. Having a non-return flap fitted in the ducting ...
-
Miele DA3060 - page 10
Guide to the appliance 10 ...
-
Miele DA3060 - page 11
a Exhaust socket ø 150 mm b Control panel c Grease filter d Pull-out deflector plate e Hob lighting f Charcoal filter (extra accessory available to order for recirculation mode) g Drop-down lightshield to conceal control panel The front of the deflector plate can be fitted with a lightshield to match your kitchen furniture. The front can also be f ...
-
Miele DA3060 - page 12
A range of Miele branded cleaning and conditioning agents are available to order through your Miele Dealer / Chartered Agent, the Miele Spare Parts Department, or via the internet on www.miele-shop.com. , Before any cleaning or maintenance work is carried out, disconnect the cooker hood from the mains supply. , Halogen lamps get very hot during use ...
-
Miele DA3060 - page 13
Controls The controls may suffer discolouration or damage if soiling is left on them for too long. Remove soiling straight away. Observe the General notes on cleaning earlier in this section. Do not use stainless steel cleaning agents on the controls. Important for DFB aluminium lightshields (optional accessory) Aluminium is affected by the way tha ...
-
Miele DA3060 - page 14
Cleaning the grease filters by hand ^ Clean the filters with a soft nylon brush in a mild solution of hot water and a small amount of washing-up liquid. Do not use undiluted washing up liquid. Do not use: – cleaning agents containing descaling agents, – powder cleaners, cream cleaners or abrasive all-purpose cleaning agents, – oven sprays. Cl ...
-
Miele DA3060 - page 15
Fitting and replacing the charcoal filter If the cooker hood is connected for recirculation, a charcoal filter (optional accessory) must be inserted in addition to the grease filter. This is designed to absorb cooking smells. It is fitted in the canopy above the grease filter. Replacement charcoal filters can be obtained from your Dealer / Chartere ...
-
Miele DA3060 - page 16
Changing a halogen lamp ^ Pull out the deflector plate, and remove the grease filter as described earlier. ^ Switch off the fan and the lighting. , Exercise caution when changing halogen lamps. They get very hot during use, and remain hot for some time after being switched off. Do not touch the surface directly when changing a lamp, as grease parti ...
-
Miele DA3060 - page 17
1) The front section of the wall housing unit must be fitted with a shelf to the depth of the partition wall. 2) The partition wall in the wall unit must be removable. 3) In extraction mode: when measuring for the height of the wall housing unit and the cut-out, account must be taken of any accessories fitted, e.g. silencer. 4) Recirculation mode r ...
-
Miele DA3060 - page 18
Installation accessories Installation 18 ...
-
Miele DA3060 - page 19
a 1 exhaust connection for exhaust ducting C 150 mm. b 1 reducing collar for exhaust ducting C 125 mm. c 1 non-return flap for fitting into the exhaust socket on the motor unit (only for air extraction mode). d 2 brackets to support the appliance in the wall unit. e 1 spacer strip to conceal the gap between the rear of the appliance and the wall. f ...
-
Miele DA3060 - page 20
Installation 20 ...
-
Miele DA3060 - page 21
Positioning the appliance in the wall housing unit To position the appliance correctly, cut the spacer strip to required depth T, and then attach it to the back of the appliance. T = Depth of carcase K minus depth of appliance G ^ The depth of appliance G depends on the lightshield being used: – a Lightshield to match existing kitchen furniture ? ...
-
Miele DA3060 - page 22
^ Screw the brackets onto the right and left inside walls of the housing unit as shown. The back edge of the brackets should align with the vertical line drawn up from the front of the spacer strip, and the lower edge aligned with the lower edge of the housing unit side wall. The brackets are designed for 16 and 19 mm thick carcase sides. Orientate ...
-
Miele DA3060 - page 23
^ Lift the appliance up into the housing from below, and engage in the brackets. Note for dismantling the cooker hood: Undoing the screws on the left and right inside the housing releases the brackets, allowing the appliance to be removed from the unit. ^ Push the cooker hood back against the spacer strip. ^ Pull out the deflector plate. ^ Secure t ...
-
Miele DA3060 - page 24
^ Secure the front of the appliance to the floor of the housing unit from below using 4 screws. To avoid damaging the deflector plate when it is pulled out, care should be taken to screw the fixing screws in straight, and to ensure that the screwheads are countersunk. ^ Only for Australia; wall housing unit without floor: ^ Loosen the screws of the ...
-
Miele DA3060 - page 25
Attaching the lightshield ^ Attach the lightshield (if using). A DML 300 installation kit, available as an optional accessory, is required for this. This installation kit is supplied with the DFB lightshield. Follow the installation instructions supplied. Weight of a lightshield matching existing furniture The lightshield must not exceed 1300 g in ...
-
Miele DA3060 - page 26
Fitting the grease filter ^ Remove the protective strip around the edge of the grease filter. Fit the grease filter. ^ To do this, pull the deflector plate out. ^ Turn the grease filter so that the red plastic guides are at the front and facing upwards. ^ Fit the grease filter in the front of the deflector plate, press it upwards and push it in tog ...
-
Miele DA3060 - page 27
Set up for extraction mode ^ If the on-site ventilation system does not have a non-return flap , then the non-return flap supplied with the appliance must be fitted in the exhaust socket in the motor unit. ^ When using C 150 mm ducting, secure the exhaust connection supplied to exhaust ducting with hose clips. ^ If using C 125 mm ducting, fit the r ...
-
Miele DA3060 - page 28
Set up for recirculation mode If site conditions are not suitable for the cooker hood to be used with air extraction, the appliance must be set up for recirculation. For this, a conversion kit DUU 151, available from your Miele dealer or the Miele Spare Parts Dept., is required. You will also need a charcoal filter (see “Technical data”). ^ Fit ...
-
Miele DA3060 - page 29
Important: To avoid the danger of toxic fumes, please observe the Warning and Safety instructions. This is especially crucial when using the cooker hood at the same time as another heating appliance which relies on air from the same room. The cooker hood should be installed according to local and national building regulations. Seek approval from th ...
-
Miele DA3060 - page 30
Condensate trap (optional accessory) In addition to insulating the exhaust ducting, we recommend that a suitable condensate trap is also installed to collect and evaporate any condensate which may occur. Condensate traps are available for C 125 mm or C 150 mm ducting. When installing a condensate trap, ensure that it is positioned vertically and if ...
-
Miele DA3060 - page 31
Silencer (optional accessory) To achieve even further reductions in noise levels, a special silencer can be fitted in the ducting system. ...with air extraction: The silencer not only reduces noise from the fan, but also sounds from outside (e.g. traffic noise). For this reason the silencer must be positioned as close as possible to where the ducti ...
-
Miele DA3060 - page 32
All electrical work should be undertaken by a suitably qualified and competent person in strict accordance with current national and local safety regulations (BS 7671 in the UK). Installation, repairs and other work by unqualified persons could be dangerous, for which the manufacturer cannot be held liable. Ensure power is not supplied to the appli ...
-
Miele DA3060 - page 33
In the event of a fault which you cannot correct yourself, or if the appliance is under guarantee, please contact: – Your Miele Dealer / Chartered Agent or – The Miele Service Department (see back cover for address). When contacting your Dealer or Miele, please quote the model and serial number of your appliance. These are shown on the data pla ...
-
Miele DA3060 - page 34
Connected load ..............2 1 0W Fan motor .................1 1 0W Hob lighting .............2x5 0W Voltage ....................2 3 0V Frequency .................~5 0H z Fuse rating GB .................3A Fuse rating (IRL) ...............1 0A AUS, NZ: Plug rating ...................1 0A Test marks .......... Electrical safety ................... ...
-
Miele DA3060 - page 35
35 ...
-
Miele DA3060 - page 36
Alteration rights reserved / 1111 M.-Nr. 07 773 930 / 02 ...
Do you have a question concerning Miele DA3060?
Use the form below
If you did not solve your problem by using a manual Miele DA3060, ask a question using the form below. If a user had a similar problem with Miele DA3060 it is likely that he will want to share the way to solve it.