-
Panasonic PT-RW430E - page 1
Thank you for purchasing this Panasonic product. ■ Before operating this product, please read the instructions carefully and save this manual for future use. ■ Before using your projector , be sure to read “Read this rst!” ( x pages 2 to 9). Model No. PT-RZ470EK PT-RZ470EW PT-RW430EK PT-RW430EW TQBJ0494 DLP TM Projector Comme ...
-
Panasonic PT-RW430E - page 2
2 - ENGLISH Read this rst! Read this rst! W ARNING: THIS APP ARA TUS MUST BE EARTHED. W ARNING: T o prevent damage which may result in re or shock hazard, do not expose this appliance to rain or moisture. This device is not intended for use in the direct eld of view at visual display workplaces. T o avoid incommoding reexions at visu ...
-
Panasonic PT-RW430E - page 3
ENGLISH - 3 Read this rst! Importer ’ s name and address within the European Union Panasonic Marketing Europe GmbH Panasonic T esting Center Winsbergring 15, 22525 Hamburg, Germany TQFX340 (T op of product) ...
-
Panasonic PT-RW430E - page 4
4 - ENGLISH Read this rst! W ARNING: r PO WER The wall outlet or the circuit breaker shall be installed near the equi pment and shall be easily accessible when problems occur . If the following problems occur , cut off the power supply immediately . Continued use of the projector in these conditions will result in re or electric shock. f If f ...
-
Panasonic PT-RW430E - page 5
ENGLISH - 5 Read this rst! W ARNING: Do not cover the air intake/exhaust ports or place anything within 500 mm (20") of them. Doing so will cause the projector to overheat, which can cause re or damage to the projector . f Do not place the projector in narrow , badly ventilated places. f Do not place the projector on cloth or papers, as ...
-
Panasonic PT-RW430E - page 6
6 - ENGLISH Read this rst! W ARNING: r ACCESSORI ES Do not use or handle the batteries improperly , and refer to the following. Failure to observe this will cause burns, batteries to leak, overheat, explode or catch re. f Use AA/R6/LR6 batteries. f Do not use unspecied batteries. f Do not use chargeable batteries. f Do not disassemble dry ...
-
Panasonic PT-RW430E - page 7
ENGLISH - 7 Read this rst! CAUTION: r PO WER When disconnecting the power cord, be sure to hold the power plug and power connector . If the power cord itself is pulled, the lead will become damaged, and re, short-circuits or serious electric shocks will result. When not using the projector for an extended period of time, disconnect the power ...
-
Panasonic PT-RW430E - page 8
8 - ENGLISH Read this rst! CAUTION: r VIE WING 3D VIDE O Those with a medical history of oversensitivity to light, heart problems, or poor physical health should not view 3D images. This may lead to a worsening of medical conditions. If you feel tiredness or discomfort, or other abnormality while viewing with 3D Eyewear , discontinue viewing. Co ...
-
Panasonic PT-RW430E - page 9
ENGLISH - 9 Read this rst! T o remove the battery Remote Control Battery 1. Pres s th e g u i de a n d l ift th e cove r . (i) (ii) 2. Remo ve the bat terie s. ...
-
Panasonic PT-RW430E - page 10
10 - ENGLISH r T rademarks f SOLID SHINE is a trademark of Panasonic Corporation. f RealD 3D is a trademark of RealD Inc. f Windows ® , Windows Vista ® , and Internet Explorer ® are registered trademarks or trademarks of Microsoft Corporation in the United States and other countries. f Mac, Mac OS, OS X, and Safari are registered trademarks of A ...
-
Panasonic PT-RW430E - page 11
ENGLISH - 1 1 Features of the Projector Easy setup and improved serviceability ▶ In addition to the 2x zoom lens and wide lens shift, the portrait setting is supported. Also, a highly exible setup is achieved through DIGIT AL LINK ( x page 18) support. Long-life reliability achieved ▶ The reliability is enhanced through the power-driving and ...
-
Panasonic PT-RW430E - page 12
12 - ENGLISH Contents Contents Read this rst! ............................................ 2 Chapter 1 Preparation Precautions for use ................................................. 15 Cautions when transporting .................................. 15 Cautions when installing ....................................... 15 Security ................. ...
-
Panasonic PT-RW430E - page 13
ENGLISH - 13 Contents [3D SETTINGS] menu .............................................. 64 [3D MODE] ........................................................... 64 [3D SYNC OUTPUT DELA Y] ................................ 64 [LEFT/RIGHT SW AP] ........................................... 64 [3D INPUT FORMA T] ......................................... ...
-
Panasonic PT-RW430E - page 14
14 - ENGLISH Chapter 1 Preparation This chapter describes things you need to know or check before using the projector . ...
-
Panasonic PT-RW430E - page 15
Chapter 1 Preparation — Precautions for use ENGLISH - 15 Precautions for use Cautions when transporting f When transporting the projector , hold it securely by its bottom and avoid excessive vibration and impacts. They may damage the internal components and result in malfunctions. f Do not transport the projector with the adjustable feet exte ...
-
Panasonic PT-RW430E - page 16
Chapter 1 Preparation — Precautions for use 16 - ENGLISH r Do not use the projector with the connecting terminal side up. Using the projector at an angle that exceeds the available angle of 210° may result in malfunctions. If setting up the projector at an angle that exceeds 210° is required, consult your dealer . 210° 210° 105° 15° 105 ...
-
Panasonic PT-RW430E - page 17
Chapter 1 Preparation — Precautions for use ENGLISH - 17 r Cautions when setting up the projector f T o install and use the projector via a method that does not use the adjustable feet in a oor standing installation, x the projector using the four screw holes for ceiling mounting (as shown in the gure). (Screw diameter: M4, tapping d ...
-
Panasonic PT-RW430E - page 18
Chapter 1 Preparation — Precautions for use 18 - ENGLISH f Change your password periodically . f Panasonic Corporation or its afliate companies will never ask for your password directly . Do not divulge your password in case you receive such inquiries. f The connecting network must be secured by a rewall, etc. f Set a password for the w ...
-
Panasonic PT-RW430E - page 19
Chapter 1 Preparation — Precautions for use ENGLISH - 19 Accessories Make sure that the following accessories are provided with your projector . Numbers enclosed in < > show the number of accessories. Wireless remote control unit <1> (N2QA YB000812) Power cord <1> (TXFSX01RXQZ) CD-ROM <1> (TXFQB02VLF2) AA/R6 or AA/LR6 ...
-
Panasonic PT-RW430E - page 20
Chapter 1 Preparation — Start-up display 20 - ENGLISH Start-up display The initial setting screen is displayed when the projector is switched on for the rst time after purchase as well as when [ALL USER DA T A] in the [PROJECTOR SETUP] menu → [INITIALIZE] is executed. Set them in accordance with circumstances. In other occasions, you can ...
-
Panasonic PT-RW430E - page 21
Chapter 1 Preparation — About your projector ENGLISH - 21 About your projector Remote control 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Attach a strap according to usage condition. Front To p 1 Remote control indicator Flashes if any button in the remote control is pressed. 2 Power < v / b > button Sets the projector to the standby mode wh ...
-
Panasonic PT-RW430E - page 22
Chapter 1 Preparation — About your projector 22 - ENGLISH Note f The remote control can be used within a distance of about 15 m (49'2") if pointed directly at the remote control receiver . The remote control can control at angles of up to ± 15° vertically and ± 30° horizontally , but the effective control range may be reduced. f ...
-
Panasonic PT-RW430E - page 23
Chapter 1 Preparation — About your projector ENGLISH - 23 r Control panel 3 4 1 2 1 Power < v / b > button Sets the projector to the state where the projector is switched off (standby mode) when the <MAIN POWER> switch on the projector is set to <ON> and in projection mode. Also sets the projector in projection mode when the ...
-
Panasonic PT-RW430E - page 24
Chapter 1 Preparation — Using the remote control 24 - ENGLISH Using the remote control Inserting and removing the batteries (i) (ii) Fig. 1 Fig. 2 1) Open the cover . (Fig. 1) 2) Insert the batteries and close the cover (insert the m side first). (Fig. 2) f When removing the batteries, perform the steps in reverse order . Setting the remote c ...
-
Panasonic PT-RW430E - page 25
ENGLISH - 25 Chapter 2 Getting Started This chapter describes things you need to do before using the projector such as the setup and connections. ...
-
Panasonic PT-RW430E - page 26
Chapter 2 Getting Started — Setting up 26 - ENGLISH Setting up [PROJECTION METHOD] and [COOLING CONDITION] There are six ways to set up the projector . Set the [PROJECTOR SETUP] menu → [PROJECTION METHOD] and [COOLING CONDITION] depending on the environment. Also set [COOLING CONDITION] correctly . Using with incorrect settings may shorten ...
-
Panasonic PT-RW430E - page 27
Chapter 2 Getting Started — Setting up ENGLISH - 27 Screen size and throw distance Refer to the following gures and table describing projection distances to install the projector . Image size and image position can be adjusted in accordance with the screen size and screen position. SD L (L W/L T) L (L W/L T) SW SH SH SW Projection screen S ...
-
Panasonic PT-RW430E - page 28
Chapter 2 Getting Started — Setting up 28 - ENGLISH For the PT -RW430E series (The dimensions of the following table contain a slight error .) (Unit: m) Projection screen size 4:3 aspect ratio 16:9 aspect ratio 16:10 aspect ratio Diagonal (SD) Min. projection distance (L W) Max. projection distance (L T) Min. projection distance (L W) Max. pr ...
-
Panasonic PT-RW430E - page 29
Chapter 2 Getting Started — Connecting ENGLISH - 29 Connecting Before connecting f Before connecting, carefully read the operating instructions for the external device to be connected. f T urn off the power of all devices before connecting cables. f T ake note of the following points before connecting the cables. Failure to do so may result i ...
-
Panasonic PT-RW430E - page 30
Chapter 2 Getting Started — Connecting 30 - ENGLISH <HDMI IN> terminal pin assignments and signal names Outside view Pin No. Signal name Pin No. Signal name Even-numbered pins of (2) to (18) (1) (19) (2) (18) Odd-numbered pins of (1) to (19) (1) T .M.D.S data 2+ (11) T .M.D.S clock shield (2) T .M.D.S data 2 shield (12) T .M.D.S clock - ...
-
Panasonic PT-RW430E - page 31
Chapter 2 Getting Started — Connecting ENGLISH - 31 Connecting example: Computers Computer Computer Computer Computer Control computer Control computer Attention f When connecting the projector to a computer or an external device, use the power cord supplied with each device and commercially available shielded cables. f When inputting digital ...
-
Panasonic PT-RW430E - page 32
Chapter 2 Getting Started — Connecting 32 - ENGLISH Attention f Always use one of the following when connecting a VCR. g A VCR with built-in time base corrector (TBC) g A time base corrector (TBC) between the projector and the VCR f If nonstandard burst signals are connected, the image may be distorted. In such case, connect the time base cor ...
-
Panasonic PT-RW430E - page 33
ENGLISH - 33 Chapter 3 Basic Operations This chapter describes basic operations to start with. ...
-
Panasonic PT-RW430E - page 34
Chapter 3 Basic Operations — Switching on/off the projector 34 - ENGLISH Switching on/off the projector Connecting the power cord Make sure that the supplied power cord is securely xed to the projector body to prevent it from being removed easily . Conrm that the <MAIN POWER> switch is on the <OFF> side before connecting the ...
-
Panasonic PT-RW430E - page 35
Chapter 3 Basic Operations — Switching on/off the projector ENGLISH - 35 Indicator status Projector status Off The main power is switched off. Red Flashing The power is switched off (in standby mode). [ST ANDBY MODE] is set to [NORMAL]. Projection will start when the power < v / b > button is pressed. f The projector may not operate whe ...
-
Panasonic PT-RW430E - page 36
Chapter 3 Basic Operations — Switching on/off the projector 36 - ENGLISH Making adjustments and selections It is recommended that images are projected continuously for at least 30 minutes before the focus is adjusted. 3) 2) 1) 2) 1) 4) 1) Set the initial settings. ( x page 20) f The initial setting screen is displayed when the projector is sw ...
-
Panasonic PT-RW430E - page 37
Chapter 3 Basic Operations — Projecting ENGLISH - 37 Projecting Check the external device connections ( x page 29) and the power cord connection ( x page 34), and turn on the projector ( x page 35) to start projecting. Select the video for projection, and adjust appearance of the projected image. Selecting the input signal Select an input sig ...
-
Panasonic PT-RW430E - page 38
Chapter 3 Basic Operations — Projecting 38 - ENGLISH Viewing 3D images T o project/view 3D images, you need active shutter system 3D eyewear, 3D content, and devices that can play 3D content. The projector only supports frame packing system, side by side system, top and bottom system, and frame sequential system as 3D video signal input. Othe ...
-
Panasonic PT-RW430E - page 39
Chapter 3 Basic Operations — Projecting ENGLISH - 39 Adjustment range by the lens position shift (optical shift) Perform the lens position shift within the adjustment range. The focus may change when the lens position is shifted out of the adjustment range. This is because the movement of the lens is restricted to protect the optical parts. P ...
-
Panasonic PT-RW430E - page 40
Chapter 3 Basic Operations — Operating with the remote control 40 - ENGLISH Operating with the remote control Using the A V mute function If the projector is not used for a certain period of time during the meeting intermission, for example, it is possible to turn off the audio and video temporarily . button 1) Press the <A V MUTE> butt ...
-
Panasonic PT-RW430E - page 41
Chapter 3 Basic Operations — Operating with the remote control ENGLISH - 41 Switching the input The input for projection can be switched. button 1) Press the input selection (<COMPUTER>, <DVI-I>, <VIDEO>, <DIGIT AL LINK>, <HDMI>) buttons. f This operation can be also performed using the <INPUT SELECT> butto ...
-
Panasonic PT-RW430E - page 42
Chapter 3 Basic Operations — Operating with the remote control 42 - ENGLISH Using the Function button Frequently used operations can be assigned to the buttons from <FUNC1> to <FUNC3> on the remote control to be used as simple shortcut buttons. button 1) Press the <FUNC1> to <FUNC3> buttons. When assigning operations t ...
-
Panasonic PT-RW430E - page 43
ENGLISH - 43 Chapter 4 Settings This chapter describes the settings and adjustments you can make using the on-screen menu. ...
-
Panasonic PT-RW430E - page 44
Chapter 4 Settings — Menu navigation 44 - ENGLISH Menu navigation The on-screen menu (Menu) is used to perform various settings and adjustments of the projector . Navigating through the menu Operating procedure button 1) Press the <MENU> button on the remote control or control panel. f The [MAIN MENU] screen is displayed. ENTER MAIN MEN ...
-
Panasonic PT-RW430E - page 45
Chapter 4 Settings — Menu navigation ENGLISH - 45 Note f Pressing the <RETURN> button or the <MENU> button while the menu screen is displayed returns to the upper hierarchical menu screen. f Some items may not be adjusted or used for certain signal formats to be input to the projector . The menu items that cannot be adjusted or us ...
-
Panasonic PT-RW430E - page 46
Chapter 4 Settings — Menu navigation 46 - ENGLISH Main menu item Page [TEST P A TTERN] 92 [SIGNAL LIST] 93 [SECURITY] 95 [NETWORK] 98 [DIGIT AL LINK] 11 7 Sub-menu The sub-menu of the selected main menu item is displayed, and you can set and adjust items in the sub-menu. [PICTURE] Sub-menu item Factory default Page [PICTURE MODE] [GRAPHIC] *1 ...
-
Panasonic PT-RW430E - page 47
Chapter 4 Settings — Menu navigation ENGLISH - 47 Note f Sub-menu items and factory default settings differ depending on the input terminal that is selected. [DISPLA Y LANGUAGE] Details ( x page 63) [3D SETTINGS] Sub-menu item Factory default Page [3D MODE] [DLP Link] *1 64 [3D SYNC OUTPUT DELA Y] [0us] 64 [LEFT/RIGHT SW AP] [NORMAL] 64 [3D I ...
-
Panasonic PT-RW430E - page 48
Chapter 4 Settings — Menu navigation 48 - ENGLISH Sub-menu item Factory default Page [SA VE ALL USER DA T A] ― 90 [LOAD ALL USER DA T A] ― 91 [INITIALIZE] ― 91 [SERVICE P ASSWORD] ― 91 [TEST P A TTERN] Details ( x page 92) [SIGNAL LIST] Details ( x page 93) [SECURITY] Sub-menu item Factory default Page [SECURITY P ASSWORD] [OFF] 95 [S ...
-
Panasonic PT-RW430E - page 49
Chapter 4 Settings — [PICTURE] menu ENGLISH - 49 [PICTURE] menu On the menu screen, select [PICTURE] from the main menu, and select the item from the sub- menu. Refer to “Navigating through the menu” ( x page 44) for the operation of the menu screen. f After selecting the item, press asqw to set. [PICTURE MODE] Y ou can switch to the desi ...
-
Panasonic PT-RW430E - page 50
Chapter 4 Settings — [PICTURE] menu 50 - ENGLISH [BRIGHTNESS] Y ou can adjust the dark (black) part of the projected image. 1) Press as to select [BRIGHTNESS]. 2) Press qw or the <ENTER> button. f The [BRIGHTNESS] individual adjustment screen is displayed. 3) Press qw to adjust the level. Operation Adjustment Range of adjustment Press t ...
-
Panasonic PT-RW430E - page 51
Chapter 4 Settings — [PICTURE] menu ENGLISH - 51 Note f When “[PICTURE MODE]” ( x page 49) is set to [DYNAMIC], [COLOR TEMPERA TURE] is xed to [USER]. (However , [WHITE BALANCE HIGH] cannot be adjusted.) f When [COLOR MA TCHING] ( x page 67) adjustment is set to other than [OFF], [COLOR TEMPERA TURE] is xed to [USER]. Adjusting desi ...
-
Panasonic PT-RW430E - page 52
Chapter 4 Settings — [PICTURE] menu 52 - ENGLISH Note f When a name is changed, display of the [USER] menu is also changed. [DA YLIGHT VIEW] Y ou can correct the image to the optimal vividness even if it is projected under a bright light. 1) Press as to select [DA YLIGHT VIEW]. 2) Press qw or the <ENTER> button. f The [DA YLIGHT VIEW] i ...
-
Panasonic PT-RW430E - page 53
Chapter 4 Settings — [PICTURE] menu ENGLISH - 53 [SYSTEM SELECTOR] The projector will automatically detect the input signal, but you can set the system method manually when an unstable signal is input. Set the system method matching the input signal. 1) Press as to select [SYSTEM SELECT OR]. 2) Press the <ENTER> button. 3) Press as to s ...
-
Panasonic PT-RW430E - page 54
Chapter 4 Settings — [POSITION] menu 54 - ENGLISH [POSITION] menu On the menu screen, select [POSITION] from the main menu, and select the item from the sub- menu. Refer to “Navigating through the menu” ( x page 44) for the operation of the menu screen. f After selecting the item, press asqw to set. Note f When the input is set to DIGIT A ...
-
Panasonic PT-RW430E - page 55
Chapter 4 Settings — [POSITION] menu ENGLISH - 55 [ASPECT] Switch the aspect ratio of the image. The aspect ratio is switched within the screen range selected in [SCREEN SETTING]. Set [SCREEN SETTING] rst. ( x page 68) [SCREEN SETTING] can be set only on the PT -RW430E series. 1) Press as to select [ASPECT]. 2) Press qw or the <ENTER> ...
-
Panasonic PT-RW430E - page 56
Chapter 4 Settings — [POSITION] menu 56 - ENGLISH Note f When [ASPECT] is set to [NA TIVE], [ZOOM] cannot be adjusted. When [ASPECT] is set to [NORMAL] 1) Press as to select [ZOOM]. 2) Press the <ENTER> button. f The [ZOOM] screen is displayed. 3) Press as to select [MODE]. 4) Press qw to switch [MODE]. [INTERNAL] Enlarges the size with ...
-
Panasonic PT-RW430E - page 57
Chapter 4 Settings — [POSITION] menu ENGLISH - 57 [KEYSTONE] Correct the trapezoidal distortion that occurs when the projector is installed tilted or when the screen is tilted. 1) Press as to select [KEYST ONE]. 2) Press qw or the <ENTER> button. f The [KEYSTONE] individual adjustment screen is displayed. 3) Press qw to adjust. Item Det ...
-
Panasonic PT-RW430E - page 58
Chapter 4 Settings — [ADV ANCED MENU] menu 58 - ENGLISH [ADV ANCED MENU] menu On the menu screen, select [ADV ANCED MENU] from the main menu, and select the item from the sub-menu. Refer to “Navigating through the menu” ( x page 44) for the operation of the menu screen. f After selecting the item, press asqw to set. [DIGIT AL CINEMA REALI ...
-
Panasonic PT-RW430E - page 59
Chapter 4 Settings — [ADV ANCED MENU] menu ENGLISH - 59 Blanking correction Item Operation Adjustment Range of adjustment Left side of the screen [LEFT] Press the w button. The blanking zone moves to the right. Left and right: 0 (lower limit) Press the q button. The blanking zone moves to the left. Right side of the screen [RIGHT] Press the q ...
-
Panasonic PT-RW430E - page 60
Chapter 4 Settings — [ADV ANCED MENU] menu 60 - ENGLISH 3) When [ON] is selected, press the <ENTER> button. f The [EDGE BLENDING] screen is displayed. 4) Press as to specify the location to be corrected. f When joining at top: Set [UPPER] to [ON] f When joining at bottom: Set [LOWER] to [ON] f When joining at left: Set [LEFT] to [ON] f ...
-
Panasonic PT-RW430E - page 61
Chapter 4 Settings — [ADV ANCED MENU] menu ENGLISH - 61 19) Press as to select an item, and press qw to adjust the setting. [BLACK BORDER WIDTH] (Right) Projection range Edge blending [WIDTH] (Right) [MARKER] (Red) Edge blending [ST ART] (Right) ([MARKER] (Green)) [BLACK BORDER LEVEL] [NON-OVERLAPPED BLACK LEVEL] [NON-OVERLAPPED BLACK LEVEL] ...
-
Panasonic PT-RW430E - page 62
Chapter 4 Settings — [ADV ANCED MENU] menu 62 - ENGLISH [RASTER POSITION] This will allow the position of the image to move within the display area arbitrarily when the input image is not using the whole display area. 1) Press as to select [RASTER POSITION]. 2) Press the <ENTER> button. f The [RASTER POSITION] screen is displayed. 3) Pr ...
-
Panasonic PT-RW430E - page 63
Chapter 4 Settings — [DISPLA Y LANGUAGE] menu ENGLISH - 63 [DISPLA Y LANGUAGE] menu On the menu screen, select [DISPLA Y LANGUAGE] from the main menu, and display the sub- menu. Refer to “Navigating through the menu” ( x page 44) for the operation of the menu screen. f Press as to select a language, and press the <ENTER> button to s ...
-
Panasonic PT-RW430E - page 64
Chapter 4 Settings — [3D SETTINGS] menu 64 - ENGLISH [3D SETTINGS] menu On the menu screen, select [3D SETTINGS] from the main menu, and select the item from the sub-menu. Refer to “Navigating through the menu” ( x page 44) for the operation of the menu screen. f After selecting the item, press asqw to set. [3D MODE] Select a control meth ...
-
Panasonic PT-RW430E - page 65
Chapter 4 Settings — [3D SETTINGS] menu ENGLISH - 65 Note f When [3D MODE] is set to [3D SYNC] or [OFF], [DLP Link] cannot be set. f Before changing the [DLP Link] setting, display 3D images. When using VESA standard 3D eyewear 1) Press as to select [3D SYNC]. 2) Press qw to switch [3D SYNC]. f The items will switch each time you press the bu ...
-
Panasonic PT-RW430E - page 66
Chapter 4 Settings — [3D SETTINGS] menu 66 - ENGLISH [3D SAFETY PRECAUTIONS] Show the safety precautions message related to 3D viewing. 1) Press as to select [3D SAFETY PRECAUTIONS]. 2) Press the <ENTER> button. f The [3D SAFETY PRECAUTIONS] screen is displayed. f Press qw to switch the page. 1/2 MENU 2/2 MENU 3D SAFETY PRECAUTIONS If y ...
-
Panasonic PT-RW430E - page 67
Chapter 4 Settings — [DISPLA Y OPTION] menu ENGLISH - 67 [DISPLA Y OPTION] menu On the menu screen, select [DISPLA Y OPTION] from the main menu, and select the item from the sub-menu. Refer to “Navigating through the menu” ( x page 44) for the operation of the menu screen. f After selecting the item, press asqw to set. [COLOR MA TCHING] C ...
-
Panasonic PT-RW430E - page 68
Chapter 4 Settings — [DISPLA Y OPTION] menu 68 - ENGLISH Adjusting the color matching using a colorimeter Use a colorimeter that can measure chromaticity coordinates and luminance to change the colors [RED], [GREEN], [BLUE], [CY AN], [MAGENT A], [YELLOW], or [WHITE] to desired colors. 1) Press as to select [COLOR MA TCHING]. 2) Press qw to se ...
-
Panasonic PT-RW430E - page 69
Chapter 4 Settings — [DISPLA Y OPTION] menu ENGLISH - 69 [AUTO SIGNAL] Set automatic execution of auto setup. The screen display position or signal level can be adjusted automatically without pressing the <AUTO SETUP> button on the remote control on each occasion if you input unregistered signals frequently at meetings, etc. 1) Press as ...
-
Panasonic PT-RW430E - page 70
Chapter 4 Settings — [DISPLA Y OPTION] menu 70 - ENGLISH [DVI-I IN] Switch the setting when the external equipment is connected to the <DVI-I IN> terminal of the projector and the image is not projected correctly . When digital signals are input 1) Press as to select [DVI-I IN]. 2) Press the <ENTER> button. f The [DVI-I IN] screen ...
-
Panasonic PT-RW430E - page 71
Chapter 4 Settings — [DISPLA Y OPTION] menu ENGLISH - 71 [HDMI IN] Switch the setting when the external equipment is connected to the <HDMI IN> terminal of the projector and the image is not projected correctly . 1) Press as to select [HDMI IN]. 2) Press the <ENTER> button. f The [HDMI IN] screen is displayed. 3) Press qw to switc ...
-
Panasonic PT-RW430E - page 72
Chapter 4 Settings — [DISPLA Y OPTION] menu 72 - ENGLISH [7] Sets to the upper right of the screen. [8] Sets to the center right of the screen. [9] Sets to the bottom right of the screen. [1] Sets to the upper left of the screen. [2] Sets to the center left of the screen. [3] Sets to the bottom left of the screen. [4] Sets to the top center o ...
-
Panasonic PT-RW430E - page 73
Chapter 4 Settings — [DISPLA Y OPTION] menu ENGLISH - 73 Setting [W ARNING MESSAGE] Set the display/hide of the warning message. 1) Press as to select [ON-SCREEN DISPLA Y]. 2) Press the <ENTER> button. f The [ON-SCREEN DISPLA Y] screen is displayed. 3) Press as to select [W ARNING MESSAGE]. 4) Press qw to switch [W ARNING MESSAGE]. f Th ...
-
Panasonic PT-RW430E - page 74
Chapter 4 Settings — [DISPLA Y OPTION] menu 74 - ENGLISH [BACK COLOR] Set the display of the projected screen when there is no signal input. 1) Press as to select [BACK COLOR]. 2) Press qw to switch [BACK COLOR]. f The items will switch each time you press the button. [BLUE] Displays the entire projection area in blue. [BLACK] Displays the en ...
-
Panasonic PT-RW430E - page 75
Chapter 4 Settings — [DISPLA Y OPTION] menu ENGLISH - 75 Switching to the sub memory list 1) Press as to select [SUB MEMOR Y LIST], and press the <ENTER> button. f A list of sub memories registered to the signal currently input is displayed. f [SUB MEMORY LIST] can be displayed by pressing qw on the normal screen (when the menu is not d ...
-
Panasonic PT-RW430E - page 76
Chapter 4 Settings — [PROJECTOR SETUP] menu 76 - ENGLISH [PROJECT OR SETUP] menu On the menu screen, select [PROJECTOR SETUP] from the main menu, and select the item from the sub-menu. Refer to “Navigating through the menu” ( x page 44) for the operation of the menu screen. f After selecting the item, press asqw to set. [PROJECTOR ID] The ...
-
Panasonic PT-RW430E - page 77
Chapter 4 Settings — [PROJECTOR SETUP] menu ENGLISH - 77 [COOLING CONDITION] Change the fan control depending on the direction of projection. Set [COOLING CONDITION] correctly in accordance with the direction of projection referencing the following gure. Using the light source with incorrect settings may shorten its life. 15° 15° 15° 15 ...
-
Panasonic PT-RW430E - page 78
Chapter 4 Settings — [PROJECTOR SETUP] menu 78 - ENGLISH Setting [AUTO POWER SA VE] Set whether to enable the three functions [AMBIENT LIGHT DETECTION], [SIGNAL DETECTION], and [A V MUTE DETECTION]. 1) Press as to select [ECO MANAGEMENT]. 2) Press the <ENTER> button. f The [ECO MANAGEMENT] screen is displayed. 3) Press as to select [AUT ...
-
Panasonic PT-RW430E - page 79
Chapter 4 Settings — [PROJECTOR SETUP] menu ENGLISH - 79 4) Press qw to switch [ST ANDBY MODE]. f The items will switch each time you press the button. [ECO] Use this setting to reduce power consumption during standby . [NORMAL] Use this setting to use the network function during standby . Note f When set to [ECO], network functions are not a ...
-
Panasonic PT-RW430E - page 80
Chapter 4 Settings — [PROJECTOR SETUP] menu 80 - ENGLISH Note f When using only one projector , the value obtained by subtracting the value of the [BRIGHTNESS CONTROL GAIN] from 100 % is the maximum amount of brightness correction. Brightness cannot be corrected through brightness control since the maximum amount of correction becomes 0 % whe ...
-
Panasonic PT-RW430E - page 81
Chapter 4 Settings — [PROJECTOR SETUP] menu ENGLISH - 81 15) Press the <ENTER> button. f The specied [MODE] and [LINK] is enabled. Afterwards, if [CALIBRA TION MESSAGE] is [ON], messages during calibration is displayed. The display automatically disappears 30 seconds after calibration has been completed. f If the <ENTER> button ...
-
Panasonic PT-RW430E - page 82
Chapter 4 Settings — [PROJECTOR SETUP] menu 82 - ENGLISH When [MODE] of [BRIGHTNESS CONTROL SETUP] is set to [AUTO] and [LINK] is set from [GROUP A] to [GROUP D] The screen shows the status of the brightness control of synchronized projectors (up to eight units), including the projector being controlled through the on-screen menu. 2 1 3 4 5 7 ...
-
Panasonic PT-RW430E - page 83
Chapter 4 Settings — [PROJECTOR SETUP] menu ENGLISH - 83 Brightness control adjustment procedure example This is an example of an adjustment procedure for synchronizing the brightness of eight projectors connected to the network. 1) Connect all projectors to the hub using LAN cables. ( x page 100) 2) Switch on all projectors and start project ...
-
Panasonic PT-RW430E - page 84
Chapter 4 Settings — [PROJECTOR SETUP] menu 84 - ENGLISH 3) Select and assign program to each day of week. f Press as to select the day of week, and press qw to select a program number . f Y ou can set the program from No.1 to No.7. “- - -” indicates that the program number has not been set. How to set a program Set up to 16 commands to e ...
-
Panasonic PT-RW430E - page 85
Chapter 4 Settings — [PROJECTOR SETUP] menu ENGLISH - 85 12) Press the <ENTER> button. f The command is xed and n is displayed at the left of the selected command. f After the command is xed, press the <RETURN> button or the <MENU> button to close the detailed setting menu. 13) Press as to select [ST ORE], and press th ...
-
Panasonic PT-RW430E - page 86
Chapter 4 Settings — [PROJECTOR SETUP] menu 86 - ENGLISH Note f When the Panasonic twisted-pair-cable transmitter (such as the optional digital interface box (Model No.: ET -YFB100G)) is connected to the projector , its input name is reected from [INPUT1] to [INPUT10] automatically . If an item where the input name is not reected is sel ...
-
Panasonic PT-RW430E - page 87
Chapter 4 Settings — [PROJECTOR SETUP] menu ENGLISH - 87 2) Press the <ENTER> button. f The [RS-232C] screen is displayed. 3) Press as to select [EMULA TE]. 4) Press the <ENTER> button. 5) Press as to select an item. [DEF AUL T] RZ470 series, RW430 series, RZ370 series, RW330 series [D3500] D3500 series [D4000] D4000 series [D/W5k ...
-
Panasonic PT-RW430E - page 88
Chapter 4 Settings — [PROJECTOR SETUP] menu 88 - ENGLISH [AUDIO SETTING] Set advanced audio functions. Adjusting the volume 1) Press as to select [AUDIO SETTING]. 2) Press the <ENTER> button. f The [AUDIO SETTING] screen is displayed. 3) Press as to select [VOLUME]. 4) Press qw to adjust the level. Operation Adjustment Range of adjustme ...
-
Panasonic PT-RW430E - page 89
Chapter 4 Settings — [PROJECTOR SETUP] menu ENGLISH - 89 4) Press qw to switch [HDMI]. f The items will switch each time you press the button. [HDMI AUDIO] Outputs HDMI audio. [AUDIO IN] Outputs audio connected via the <AUDIO IN> terminal. Note f If COMPUTER, DVI-I, or VIDEO input is selected, audio connected to the <AUDIO IN> ter ...
-
Panasonic PT-RW430E - page 90
Chapter 4 Settings — [PROJECTOR SETUP] menu 90 - ENGLISH 2) Press the <ENTER> button. f The [DA TE AND TIME] screen is displayed. 3) Press as to select [TIME ZONE]. 4) Press qw to switch [TIME ZONE]. Setting the date and time manually 1) Press as to select [DA TE AND TIME]. 2) Press the <ENTER> button. f The [DA TE AND TIME] scree ...
-
Panasonic PT-RW430E - page 91
Chapter 4 Settings — [PROJECTOR SETUP] menu ENGLISH - 91 [LOAD ALL USER DA T A] Load the various setting values saved as a backup in the built-in memory of the projector . 1) Press as to select [LOAD ALL USER DA T A]. 2) Press the <ENTER> button. f The [SECURITY P ASSWORD] screen is displayed. 3) Enter a security password and press the ...
-
Panasonic PT-RW430E - page 92
Chapter 4 Settings — [TEST P A TTERN] menu 92 - ENGLISH [TEST P A TTERN] menu On the menu screen, select [TEST P A TTERN] from the main menu. Refer to “Navigating through the menu” ( x page 44) for the operation of the menu screen. f Press qw to switch. [TEST P A TTERN] Display the test pattern built-in to the projector . Settings of posi ...
-
Panasonic PT-RW430E - page 93
Chapter 4 Settings — [SIGNAL LIST] menu ENGLISH - 93 [SIGNAL LIST] menu On the menu screen, select [SIGNAL LIST] from the main menu. Refer to “Navigating through the menu” ( x page 44) for the operation of the menu screen. r Registered signal details f A name can be set for each sub memory ( x page 74). f Memory number: A1 (1-2) When the ...
-
Panasonic PT-RW430E - page 94
Chapter 4 Settings — [SIGNAL LIST] menu 94 - ENGLISH Deleting the registered signal Registered signals can be deleted. 1) Press asqw to select the signal to delete. 2) Press the <DEF AUL T> button. f The [ENTR Y SIGNAL DELETE] screen is displayed. f T o cancel deletion, press the <RETURN> button or the <MENU> button to retur ...
-
Panasonic PT-RW430E - page 95
Chapter 4 Settings — [SECURITY] menu ENGLISH - 95 [SECURITY] menu On the menu screen, select [SECURITY] from the main menu, and select the item from the sub-menu. Refer to “Navigating through the menu” ( x page 44) for the operation of the menu screen. f When the projector is used for the rst time Initial password: Press awsqawsq in or ...
-
Panasonic PT-RW430E - page 96
Chapter 4 Settings — [SECURITY] menu 96 - ENGLISH [TEXT DISPLA Y] Overlap the security message (text) over the projected image. 1) Press as to select [TEXT DISPLA Y]. 2) Press qw to switch [TEXT DISPLA Y]. f The items will switch each time you press the button. [OFF] Hides the security message. [ON] Displays the security message. Note f If a ...
-
Panasonic PT-RW430E - page 97
Chapter 4 Settings — [SECURITY] menu ENGLISH - 97 [CONTROL DEVICE SETUP] Enable/disable the button operations on the control panel and the remote control. 1) Press as to select [CONTROL DEVICE SETUP]. 2) Press the <ENTER> button. f The [CONTROL DEVICE SETUP] screen is displayed. 3) Press as to select [CONTROL P ANEL] or [REMOTE CONTROL] ...
-
Panasonic PT-RW430E - page 98
Chapter 4 Settings — [NETWORK] menu 98 - ENGLISH [NETWORK] menu On the menu screen, select [NETWORK] from the main menu, and select the item from the sub-menu. Refer to “Navigating through the menu” ( x page 44) for the operation of the menu screen. f After selecting the item, press asqw to set. [DIGIT AL LINK MODE] Switch the communicati ...
-
Panasonic PT-RW430E - page 99
Chapter 4 Settings — [NETWORK] menu ENGLISH - 99 Note f The projector does not support 10BaseT Full/Half. When the projector is connected to a twisted-pair-cable transmitter 1) Press as to select [DIGIT AL LINK SETUP]. 2) Press the <ENTER> button. f The [DIGIT AL LINK SETUP] screen is displayed. 3) Press as to select [DUPLEX(DIGIT AL LI ...
-
Panasonic PT-RW430E - page 100
Chapter 4 Settings — [NETWORK] menu 100 - ENGLISH 5) When the confirmation is displayed, select [OK] or [CANCEL], and press the <ENTER> button. Note f When using a DHCP server , conrm that the DHCP server is running. f Consult your network administrator regarding the IP address, subnet mask, and default gateway . [NETWORK CONTROL] Se ...
-
Panasonic PT-RW430E - page 101
Chapter 4 Settings — [NETWORK] menu ENGLISH - 101 Note f “Crestron RoomView” is a system of Crestron Electronics, Inc. that collectively manages and controls devices on multiple systems connected to a network using a computer . f For details of “Crestron RoomView”, refer to the website of Crestron Electronics, Inc. (English only) URL ...
-
Panasonic PT-RW430E - page 102
Chapter 4 Settings — [NETWORK] menu 102 - ENGLISH f For the LAN cable between a twisted-pair-cable transmitter and the projector , use a cable that meets the following criteria: g Compatible with CA T5e or higher g Shielded type (including connectors) g Straight-through g Single wire f The maximum transmission distance between the twisted-pai ...
-
Panasonic PT-RW430E - page 103
Chapter 4 Settings — [NETWORK] menu ENGLISH - 103 f Do not perform setting or control simultaneously by starting up multiple web browsers. Do not set or control the projector from multiple computers. f Change the password rst. ( x page 1 13) f The administrator rights allows to use all functions. The user rights only allows use of [Project ...
-
Panasonic PT-RW430E - page 104
Chapter 4 Settings — [NETWORK] menu 104 - ENGLISH Error information page When [Error (Detail)] appears in the self-diagnosis display of the [Projector status] screen, click it to display the error details. f The projector may go into the standby status to protect the projector depending on the contents of the error . 1 1 Self-diagnosis result ...
-
Panasonic PT-RW430E - page 105
Chapter 4 Settings — [NETWORK] menu ENGLISH - 105 [Network status] page Click [Status] → [Network status]. The current network setting status is displayed. [Access error] page Click [Status] → [Access error]. The error log on the web server is displayed such as access to the pages that do not exist or access with unauthorized user names o ...
-
Panasonic PT-RW430E - page 106
Chapter 4 Settings — [NETWORK] menu 106 - ENGLISH [Basic control] page Click [Projector control] → [Basic control]. 1 2 5 6 3 4 1 [INPUT] Switches the input signal. 2 [VOLUME] Adjusts the volume. 3 [PICTURE MODE] Switches the video mode. 4 [A V MUTE] Switches between A V mute on/off. 5 [POWER] Switches on/off the power . 6 [CLOSED CAPTION] ...
-
Panasonic PT-RW430E - page 107
Chapter 4 Settings — [NETWORK] menu ENGLISH - 107 [Network cong] page Click [Detailed set up] → [Network cong]. f Click [Network cong] to display the [CAUTION!] screen. f The current settings are displayed by pressing the [Next] button. f The following setting change screen is displayed by clicking the [Change] button. 1 2 3 4 5 6 ...
-
Panasonic PT-RW430E - page 108
Chapter 4 Settings — [NETWORK] menu 108 - ENGLISH [Ping test] page Check whether the network is connected to the mail server , POP server , DNS server , etc. Click [Detailed set up] → [Ping test]. 1 2 3 4 1 [Input IP address] Enter the IP address of the server to be tested. 2 [Submit] Executes the connection test. 3 Example of display when ...
-
Panasonic PT-RW430E - page 109
Chapter 4 Settings — [NETWORK] menu ENGLISH - 109 [E-mail set up] page When there is a problem, an E-mail can be sent to preset E-mail addresses (up to two addresses). Click [Detailed set up] → [E-mail set up]. 1 2 3 4 5 6 1 [ENABLE] Select [Enable] to use the E-mail function. 2 [SMTP SER VER NAME] Enter the IP address or the server name of ...
-
Panasonic PT-RW430E - page 110
Chapter 4 Settings — [NETWORK] menu 1 10 - ENGLISH 11 10 9 9 [E-MAIL ADDRESS 2] Enter the E-mail address to be sent when two E-mail addresses are to be used. Leave it blank when two E-mail addresses are not to be used. 10 Settings of the conditions to send E-mail Select the conditions to send E-mail to the second E-mail address. [MAIL CONTENT ...
-
Panasonic PT-RW430E - page 111
Chapter 4 Settings — [NETWORK] menu ENGLISH - 1 1 1 Contents of E-mail sent Example of E-mail sent when E-mail is set The following E-mail is sent when the E-mail settings have been established. === Panasonic projector report(CONFIGURE) === Projector T ype : RW430 Serial No : SW1234567 ----- E-mail setup data ----- TEMPERA TURE WARNING SETUP ...
-
Panasonic PT-RW430E - page 112
Chapter 4 Settings — [NETWORK] menu 1 12 - ENGLISH Example of the E-mail sent for an error The following E-mail is sent when an error has occurred. === Panasonic projector report(ERROR) === Projector T ype : RW430 Serial No : SW1234567 ----- check system ----- MAIN CPU BUS [ OK ] F AN [ OK ] INT AKE AIR TEMPERA TURE [ OK ] OPTICS MODULE TEMPE ...
-
Panasonic PT-RW430E - page 113
Chapter 4 Settings — [NETWORK] menu ENGLISH - 1 13 [Change password] page Click [Change password]. 1 2 3 1 [Administrator] Used to change the setting of the [Administrator]. 2 [User] Used to change the setting of the [User]. 3 [Next] Used to change the setting of the password. [Administrator] account 1 2 3 4 5 6 7 1 [Account] Displays the acc ...
-
Panasonic PT-RW430E - page 114
Chapter 4 Settings — [NETWORK] menu 1 14 - ENGLISH [User] account 1 2 3 5 4 1 [Account] Displays the account to change. 2 [New][User name] Enter the desired new user name. (Up to 16 characters in single byte) 3 [New][Password] Enter the desired new password. (Up to 16 characters in single byte) 4 [New][Password(Retype)] Enter the desired new ...
-
Panasonic PT-RW430E - page 115
Chapter 4 Settings — [NETWORK] menu ENGLISH - 1 15 [CRESTRON RoomView] page The projector can be monitored/controlled with RoomView . T o start the RoomView control page from the web control screen, you need to access with the administrator rights. (For user rights, the [CRESTRON RoomView] button is not displayed on the web control screen.) T ...
-
Panasonic PT-RW430E - page 116
Chapter 4 Settings — [NETWORK] menu 1 16 - ENGLISH [Info] page Click [Info] on the control page. 4 5 6 7 1 2 3 8 1 [Projector Name] Displays the projector name. 2 [Mac Address] Displays the MAC address. 3 [Lamp Hours] Displays the runtime of the projector (converted value). 4 [Power Status] Displays the status of the power . 5 [Source] Displa ...
-
Panasonic PT-RW430E - page 117
Chapter 4 Settings — [DIGIT AL LINK] menu ENGLISH - 1 17 [DIGIT AL LINK] menu On the menu screen, select [DIGIT AL LINK] from the main menu. Refer to “Navigating through the menu” ( x page 44) for the operation of the menu screen. Switch the input to DIGIT AL LINK. Note f When the optional digital interface box (Model No.: ET -YFB100G) is ...
-
Panasonic PT-RW430E - page 118
1 18 - ENGLISH Chapter 5 Maintenance This chapter describes inspection when there are problems, and maintenance methods. ...
-
Panasonic PT-RW430E - page 119
Chapter 5 Maintenance — Light source/temperature indicator ENGLISH - 1 19 Light source/temperature indicator When an indicator lights up If a problem should occur inside the projector , the light source indicator <LIGHT>/temperature indicator <TEMP> will inform you by lighting or ashing. Check the status of the indicators and m ...
-
Panasonic PT-RW430E - page 120
Chapter 5 Maintenance — Maintenance 120 - ENGLISH Maintenance Before maintaining the projector f Make sure to turn off the power before maintaining the projector . ( x pages 34, 36) f When switching off the projector , make sure to follow the procedures in “Switching off the projector” ( x page 36). Maintenance Outer case Wipe off dirt an ...
-
Panasonic PT-RW430E - page 121
Chapter 5 Maintenance — T roubleshooting ENGLISH - 121 T roubleshooting Review the following points. For details, see the corresponding pages. Problems Points to be checked Page Power does not turn on. f Is the power plug rmly inserted into the outlet? ― f Is the <MAIN POWER> switch set to <OFF>? 36 f Is the wall outlet suppl ...
-
Panasonic PT-RW430E - page 122
Chapter 5 Maintenance — T roubleshooting 122 - ENGLISH Problems Points to be checked Page Left and right images are reversed (not showing properly). f Are the devices synchronized? Check the 3D eyewear settings. ― f Change the [LEFT/RIGHT SW AP] setting of [3D SETTINGS]. 64 Image in the 3D eyewear ickers. f Are you within the reception r ...
-
Panasonic PT-RW430E - page 123
ENGLISH - 123 Chapter 6 Appendix This chapter describes specications and after-sales service for the projector . ...
-
Panasonic PT-RW430E - page 124
Chapter 6 Appendix — T echnical information 124 - ENGLISH T echnical information PJLink protocol The network function of this projector supports the PJLink class 1, and the PJLink protocol can be used to perform projector setting and projector status query operations from a computer . Control commands The following table lists the PJLink prot ...
-
Panasonic PT-RW430E - page 125
Chapter 6 Appendix — T echnical information ENGLISH - 125 Control commands via LAN When web control administrator rights password is set (Protect mode) Connecting 1) Obtain the IP address and port number (Initial set value = 1024) of the projector and request for a connection to the projector . f Y ou can obtain both the IP address and the po ...
-
Panasonic PT-RW430E - page 126
Chapter 6 Appendix — T echnical information 126 - ENGLISH When web control administrator rights password is not set (Non-protect mode) Connecting 1) Obtain the IP address and port number (Initial set value = 1024) of the projector and request for a connection to the projector . f Y ou can obtain both the IP address and the port number from th ...
-
Panasonic PT-RW430E - page 127
Chapter 6 Appendix — T echnical information ENGLISH - 127 <SERIAL IN> terminal The <SERIAL IN> terminal of the connecting terminal of the projector conforms with RS-232C so that the projector can be connected to and controlled from a computer . Connection Projector connecting terminals Computer D-Sub 9p (female) D-Sub 9p (male) Co ...
-
Panasonic PT-RW430E - page 128
Chapter 6 Appendix — T echnical information 128 - ENGLISH Basic format T ransmission from the computer starts with STX, then the ID, command, parameter , and ETX are sent in this order. Add parameters according to the details of control. (2 bytes) 2 ID characters (2 bytes) Semi-colon (1 byte) Colon (1 byte) 3 command characters (3 bytes) Para ...
-
Panasonic PT-RW430E - page 129
Chapter 6 Appendix — T echnical information ENGLISH - 129 Cable specication 1 NC NC 1 2 2 3 3 4 NC NC 4 5 5 6 NC NC 6 7 7 8 8 9 NC NC 9 When connected to a computer Projector (<SERIAL IN> terminal) Computer (DTE specifications) Control command The following table lists the commands that can be used to control the projector using a co ...
-
Panasonic PT-RW430E - page 130
Chapter 6 Appendix — T echnical information 130 - ENGLISH List of compatible signals The following table species the types of signals compatible with the projector . Items that are applicable to 1 to 3 in the table are as follows. 1 COMPUTER/DVI-I (analog EDID) 2 DVI-I digital 3 HDMI/DIGIT AL LINK f Symbols that indicate formats are as fol ...
-
Panasonic PT-RW430E - page 131
Chapter 6 Appendix — T echnical information ENGLISH - 131 Mode Resolution (Dots) Scanning freq. Dot clock freq. (MHz) Format Plug and play *1 Horizontal (kHz) V ertical (Hz) 1 2 3 EDID1 EDID2 EDID3 SXGA 1 280 x 1 024 64.0 60.0 108.0 R/D/H l ― l l l 1 280 x 1 024 80.0 75.0 135.0 R/D/H l ― l l l 1 280 x 1 024 91.1 85.0 157.5 R/D/H ― ― ? ...
-
Panasonic PT-RW430E - page 132
Chapter 6 Appendix — T echnical information 132 - ENGLISH List of 3D compatible signals The following table species the types of 3D video signals compatible with the projector . Items that are applicable to 1 to 4 in the table are as follows. 1 Frame packing system 2 Side by side system 3 T op and bottom system 4 Frame sequential system 3D ...
-
Panasonic PT-RW430E - page 133
Chapter 6 Appendix — Specications ENGLISH - 133 Specications The following table describes the specications of the projector . Model No. PT -RZ470EK/PT-RZ470EW PT-R W430EK/PT -RW430EW Power supply AC 100 V - 240 V 50 Hz/60 Hz Power consumption 460 W (5.2 A - 2.0 A) 0.5 W when [ST ANDBY MODE] is set to [ECO] 8 W when [ST ANDBY MODE] i ...
-
Panasonic PT-RW430E - page 134
Chapter 6 Appendix — Specications 134 - ENGLISH Model No. PT -RZ470EK/PT-RZ470EW PT -RW430EK/PT -RW430EW Color system 7 standards (NTSC/NTSC4.43/P AL/P AL-N/P AL-M/SECAM/P AL60) Projection screen size 1.02 m (40") to 7.62 m (300") Screen aspect ratio 16:9 16:10 Projection method [FRONT/CEILING], [FRONT/FLOOR], [REAR/CEILING], [RE ...
-
Panasonic PT-RW430E - page 135
Chapter 6 Appendix — Dimensions ENGLISH - 135 Dimensions Unit: mm 409 (16-3/32") 415 (16-11/32") 455 (17-29/32") 63.5 (2-1/2") 72 (2-27/32") 72 (2-27/32") 63.5 (2-1/2") 137 (5-13/32") 128.5 (5-1/16") 125 (4-29/32") * Actual dimensions may differ depending on the product. ...
-
Panasonic PT-RW430E - page 136
Chapter 6 Appendix — Ceiling mount bracket safeguards 136 - ENGLISH Ceiling mount bracket safeguards f When installing the projector to a ceiling, be sure to use the specied ceiling mount bracket (Model No.: ET -PKR100H (for high ceilings), ET -PKR100S (for low ceilings), ET-PKR100P (for portrait)). f When installing the projector , attach ...
-
Panasonic PT-RW430E - page 137
Index ENGLISH - 137 0 – 9 [3D INPUT FORMA T] .......................................... 65 [3D MODE] .......................................................... 64 [3D SAFETY PRECAUTIONS] ............................ 66 [3D SETTINGS] ............................................. 47, 64 A Accessories ................................................ ...
Do you have a question concerning Panasonic PT-RW430E?
Use the form below
If you did not solve your problem by using a manual Panasonic PT-RW430E, ask a question using the form below. If a user had a similar problem with Panasonic PT-RW430E it is likely that he will want to share the way to solve it.