English dropdown-ico

Manual Bryant 383KAV

12 pages 0.2 mb
Download

Go to site of 12

Summary
  • Bryant 383KAV - page 1

    SAFETY CONSIDERATIONS NOTE: Read the entire instruction manual before performing any service or maintenance. This symbol → indicates a change since the last issue. These procedures are for size 45,000 through 155,000 Btuh input units. Index Page SAFETY CONSIDERATIONS ..................................................1-2 ELECTROSTATIC DISCHARGE (E ...

  • Bryant 383KAV - page 2

    WARNING: The ability to properly perform mainte- nance on this equipment requires certain expertise, me- chanical skills, tools, and equipment. If you do not possess these, do not attempt to perform any maintenance on this equipment other than those procedures recom- mended in the User’s Manual. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN POSS ...

  • Bryant 383KAV - page 3

    1. Downflow/Horizontal Each furnace requires 2 filters which are installed in the return-air duct. (See Fig. 4 and 5.) To remove filters for cleaning or replacement, proceed as follows: a. Disconnect electrical power before removing blower access door. b. Remove screw from front of door and remove blower access door. c. Reach up behind top plate, t ...

  • Bryant 383KAV - page 4

    a. Remove dust caps or plugs from oil ports located at each end of motor. b. Use a good grade of SAE 20 nondetergent motor oil and put 1 teaspoon, 5 cc, 3/16 oz, or 16 to 25 drops in each oil port. Do not over-oil. c. Allow time for total quantity of oil to be absorbed by each bearing. d. Wipe excess oil from motor housing. e. Replace dust caps or ...

  • Bryant 383KAV - page 5

    (2.) Use 1/4-in. diameter wire brush (commonly known as 25-caliber rifle cleaning brush). NOTE: The materials needed in items (1.) and (2.) can usually be purchased at local hardware stores. (3.) Insert twisted wire end of brush into end of steel spring cable, and crimp tight with crimping tool or strike with ball-peen hammer. TIGHTNESS is very imp ...

  • Bryant 383KAV - page 6

    The electrical ground and polarity for 115-v wiring must be maintained properly. Refer to Fig. 10 for field wiring information and to Fig. 12 for unit wiring information. NOTE: If the polarity is not correct, the STATUS LED on the control center will flash rapidly and prevent the furnace from operating. The control system also requires an earth gro ...

  • Bryant 383KAV - page 7

    → Fig. 10—Heating and Cooling Application Wiring Diagram A98209 115-V FIELD-SUPPLIED DISCONNECT AUXILIARY J-BOX CONTROL BOX 24-V TERMINAL BLOCK THREE-WIRE HEATING- ONLY FIVE WIRE NOTE 1 NOTE 2 FIELD-SUPPLIED DISCONNECT CONDENSING UNIT TWO WIRE FURNACE R G C WC R GY GND GND FIELD 24-V WIRING FIELD 115-, 208/230-, 460-V WIRING FACTORY 24-V WIRING ...

  • Bryant 383KAV - page 8

    → Fig. 12—Wiring Diagram A98200e PCB BLOWER O FF DE LAY SELECTI O N CH ART 90 SEC 135 SEC 180 SEC 225 SEC GVR H I/L O RELAY SEC-1 SEC- 2 PL1 32 1 6 5 4 987 LED TEST/TW IN BLOWER OFF DELAY G R Y W C HUM HSIR IDR BLWR BLOWER SPEED SELECT FU1 COOL HEAT L2 PL3 PL2 VAC 120 L1 PR1 1 2 1 2 3 PR2 24 VAC-3A FUSE SPARE-2 SPARE-1 EAC-1 EAC-2 C 1. 5 A M ...

  • Bryant 383KAV - page 9

    Fig. 13—Service Label A96263 SERVICE 11 NO PREVIOUS CODE - Stored status codes are erased when power ( 115V or 24V) to control is interrupted or 48 hours after ea ch fault is cleared. 12 BLOWER ON AFTER POWER UP (115V or 24V) - Blowe r runs for 90 seconds, if unit is powered up during a call for heat (R-W closed). 13 LI MIT OR FLAME ROLL-OU T SWI ...

  • Bryant 383KAV - page 10

    Is circuit breaker closed? Close door switch and go to start. Is red LED status light on? Is door switch closed? Is red LED status light blinking rapidly without a pause? Is there 115v going to switch? Replace door switch. Replace control center. Replace transformer. Is red LED status light blinking ON/OFF slowly with a combination of shor ...

  • Bryant 383KAV - page 11

    11 NO PREVIOUS FAULT - Faults are erased after 48 hrs or whenever power (115V or 24V) is interrupted. Run system through a heating or cooling cycle to recheck system. 12 BLOWER ON AFTER POWER UP (115V OR 24V) - Normal  operation. Blower will run for 90 sec when furnace power is interrupted during a call for heat and R- ...

  • Bryant 383KAV - page 12

    A94328 SERVICE TRAINING Packaged Service Training programs are an excellent way to increase your knowledge of the equipment discussed in this manual, including:  • Unit Familiarization • Maintenance  • Installation Overview • Operating Sequence A large selection of product, theory, and skills programs is availa ...

Manufacturer Bryant Category Furnace

Documents that we receive from a manufacturer of a Bryant 383KAV can be divided into several groups. They are, among others:
- Bryant technical drawings
- 383KAV manuals
- Bryant product data sheets
- information booklets
- or energy labels Bryant 383KAV
All of them are important, but the most important information from the point of view of use of the device are in the user manual Bryant 383KAV.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Bryant 383KAV, service manual, brief instructions and user manuals Bryant 383KAV. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Bryant 383KAV.

Similar manuals

A complete manual for the device Bryant 383KAV, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Bryant 383KAV by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Bryant 383KAV.

A complete Bryant manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Bryant 383KAV - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Bryant 383KAV, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Bryant 383KAV, that we can find in the current document
3. Tips how to use the basic functions of the device Bryant 383KAV - which should help us in our first steps of using Bryant 383KAV
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Bryant 383KAV
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Bryant 383KAV in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Bryant 383KAV?

Use the form below

If you did not solve your problem by using a manual Bryant 383KAV, ask a question using the form below. If a user had a similar problem with Bryant 383KAV it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)