English dropdown-ico

Manual APC SURT8000XLI+LE600I

19 pages Not applicable
Download

Go to site of 19

Summary
  • APC SURT8000XLI+LE600I - page 1

    Smart-UPS ® RT Uninterruptible Power Supply SURT 8000/10000 VA 200-240 VAC Tower/Rack-Mount 6U English © 2012 APC by Schneider Electric. APC, the APC logo, Sm art-UPS and PowerChute are owned by Schneider Electric Industries S.A.S., American Power Conversi on Corporation, or affiliated companies. All other trademarks are the property of their res ...

  • APC SURT8000XLI+LE600I - page 2

    ...

  • APC SURT8000XLI+LE600I - page 3

    Introduction The APC ® by Schneider Electric Sm art-UPS ® RT is a high-performance, uninterruptible power supply (UPS) that provides protection for electronic equipment from utility power blackouts, brownouts, sags and su rges. The UPS filters small utility line fluctuations an d isolates electronic equipment from large disturbances by internally ...

  • APC SURT8000XLI+LE600I - page 4

    Hardwiring Wiring must be performed by a qualified electrician. 1. Install a utility circuit breaker in accordance with local electrical codes (see tables below) for input wiring. 2. Switch the UP S input circui t breaker (see A ) and utility circuit breakers OFF. 3. Remove the ac cess panel (see B ). 4. Remove circ ular knoc kouts. 5. Run wires th ...

  • APC SURT8000XLI+LE600I - page 5

    7. XLI mo del only: For three-phase input, set the Input Phase Selector switch (see C ) to ‘3’. For single-phase input, leave switch in default position of ‘1’. 8. Switch the circuit breakers ON. 9. Check line voltages. 10. Replace the ac cess panel. XLT/XLJ/XLTW M ODELS O UTPUT L1A L2A I NPUT L1 L2 A B XLI M ODEL O UTPUT L1A N1 I NPUT L1 L ...

  • APC SURT8000XLI+LE600I - page 6

    Installing and Connecti ng the Batteries and Attaching the Front Bezel       4 ...

  • APC SURT8000XLI+LE600I - page 7

    C ONNECTING P OWER AND E QUIPMENT TO THE UPS 1. Hardwire the UPS (see Hardwiring ). 2. Connect equipment to th e UPS (cables not included for XLT/XLJ/XLTW models). 3. Turn on all connected equipm ent. To use the UPS as a m aster on/off switch, be sure that all connected equipm ent is switched ON. 4. Press the button on the front panel to power up t ...

  • APC SURT8000XLI+LE600I - page 8

    B ASIC C ONNECTORS Serial Port Power m anagement software and inte rface kits can be used with the UPS. Use only inter face kits suppli ed or approved b y APC. Ethernet Port Co nnect the UPS to the network. (Located on th e Network Managem ent Card .) EPO Terminal The o ptional Emergency Power Off (EPO) feature allows connected loads to be immediat ...

  • APC SURT8000XLI+LE600I - page 9

    O PERA TION F RONT D ISPLAY P ANEL Indicator Description Online The UPS is drawing utility power and performin g double conversion to sup ply power to connected equipm ent (see Troubl eshootin g ). On Battery The UPS is supplying batter y powe r to the connected equi pment. Bypass The UPS is in bypass mode, sending utility power directly to connect ...

  • APC SURT8000XLI+LE600I - page 10

    Feature Function Normal /Bypass Manually switch connected eq uipment to bypass mode, so that utility power is sent directly to connected equipment. Battery op eration is not available while the UPS is in bypass mode. (See Troubleshooting. ) Cold Start This is not a normal condition. Supply imm ediate battery p ower to th e UPS and connected equipme ...

  • APC SURT8000XLI+LE600I - page 11

    U SER C ONFIGURABLE I TEMS N OTE : S ETTINGS ARE MADE THROUGH SUPPLIED P OWER C HUTE SOFTWARE , N ETWORK M ANAG E ME NT CAR D , OPTIONAL S MA RT S LOT A CCESSORY CARDS OR T ERMINA L M ODE . F UNCTION F ACTORY D EFAULT U SER S ELECTABLE C HOICES D ESCRIPTION Automatic Self-Test Every 14 days (336 hours) Every 7 d ays (168 hours), Every 14 days (336 ...

  • APC SURT8000XLI+LE600I - page 12

    N OTE : S ETTINGS ARE MADE THROUGH SUPPLIED P OWER C HUTE SOFTWARE , N ETWORK M ANAG E ME NT CAR D , OPTIONAL S MA RT S LOT A CCESSORY CARDS OR T ERMINA L M ODE . F UNCTION F ACTORY D EFAULT U SER S ELECTABLE C HOICES D ESCRIPTION High Bypass Point +10% of output voltage setting +5%, +10%, +15%, +20% Maximum voltage that the UPS will pass to connec ...

  • APC SURT8000XLI+LE600I - page 13

    EPO (Emergency Power Off) Option The output power can be disabled i n an emerge ncy by closing a switch connected to t he EPO. Adhere to national an d local electrical codes when wiring. The switch should be connected in a normally open switch contact. External voltage is not required; the switch is driven by 12V internal supply. In closed conditio ...

  • APC SURT8000XLI+LE600I - page 14

    Terminal Mode to Configure UPS Parameters Terminal Mode is a me nu driven interface that enables enhanced c onfiguration of the UPS. Connect the serial cable to the se rial port on the back of the UPS. 1. Open a term inal program . Exampl e: HyperTerm inal  From the Desktop, go to Start => Programs => Accessories => Com munication => ...

  • APC SURT8000XLI+LE600I - page 15

    M AINTENANCE , S ERVICE , W ARRANTY , AND T RANS PORTING Replacing the Battery Module(s) This UPS has e asy to replace, hot -swappable ba ttery m odules. Replacement is a sa fe procedure, isolated from electrical hazards. You may leave the UPS and connected eq uipment on during the procedure. See your dealer or contact APC at the Web site, www.apc. ...

  • APC SURT8000XLI+LE600I - page 16

    T ROUBLESHOOTING Use the table below to solve minor installation and operation problems. Refer to the APC Web site, www.apc.com for assistance with complex UPS problems. P ROBLEM AND P OSSIBLE C AUS E S OLUTION UPS WILL NOT TURN ON Batteries are not connected properly. Check that the battery connectors ar e fully engaged. button not pushed. Press t ...

  • APC SURT8000XLI+LE600I - page 17

    15 P ROBLEM AND P OSSIBLE C AUS E S OLUTION BYPASS LED ILLUMINATES The bypass switch has been turned on manually or through an accessory. If bypass is the chosen mode of ope ration, ignore the illuminated LED. If bypass is not the chosen mode of operation move the bypass switch on the back of the UPS, to the normal position. FAULT AND OVERLOAD LED ...

  • APC SURT8000XLI+LE600I - page 18

    Service If the UPS requires service do not return it to the dealer. Follow these step s: 1. Review the pr oblems di scussed in the Tr oubleshoot ing section of this manual to eliminate common pr oblems. 2. If the pro blem persists, co ntact APC C ustomer Su pport thro ugh the APC Web site, ww w.apc.com .  Note the m odel number of the UPS, t he ...

  • APC SURT8000XLI+LE600I - page 19

    17 R ADIO F REQU ENCY W ARNINGS This equipment has been tested and found to comply with the li m its for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable pr otection against harmful interf erence when the equipment is operated in a commercial environment. T his equipment generates, uses ...

Manufacturer APC Category Uninterruptible power supply (

Documents that we receive from a manufacturer of a APC SURT8000XLI+LE600I can be divided into several groups. They are, among others:
- APC technical drawings
- SURT8000XLI+LE600I manuals
- APC product data sheets
- information booklets
- or energy labels APC SURT8000XLI+LE600I
All of them are important, but the most important information from the point of view of use of the device are in the user manual APC SURT8000XLI+LE600I.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals APC SURT8000XLI+LE600I, service manual, brief instructions and user manuals APC SURT8000XLI+LE600I. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product APC SURT8000XLI+LE600I.

Similar manuals

A complete manual for the device APC SURT8000XLI+LE600I, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use APC SURT8000XLI+LE600I by users. Manuals are usually written by a technical writer, but in a language understandable to all users of APC SURT8000XLI+LE600I.

A complete APC manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual APC SURT8000XLI+LE600I - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the APC SURT8000XLI+LE600I, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the APC SURT8000XLI+LE600I, that we can find in the current document
3. Tips how to use the basic functions of the device APC SURT8000XLI+LE600I - which should help us in our first steps of using APC SURT8000XLI+LE600I
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with APC SURT8000XLI+LE600I
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of APC SURT8000XLI+LE600I in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning APC SURT8000XLI+LE600I?

Use the form below

If you did not solve your problem by using a manual APC SURT8000XLI+LE600I, ask a question using the form below. If a user had a similar problem with APC SURT8000XLI+LE600I it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)