English dropdown-ico

Manual Teledyne 102E

90 pages 2.58 mb
Download

Go to site of 90

Summary
  • Teledyne 102E - page 1

    ADDENDUM TO MODEL 101E OPERATORS MANUAL (P/N 04740 REV. A) FOR MODEL 102E TOTAL REDUCED SULFUR ANALYZER with MODEL 501 TRS THERMAL CONVERTER © TELEDYNE ADVANCED POLLUTION INSTRUMEN TATION 9480 CARROLL PARK DRI VE SAN DIEGO, CA 92121-52 01 USA Toll-free Phone: 800-324-519 0 Phone: 858-657-980 0 Fax: 858-657-981 6 Email: Api-sales@teledyne.com Websi ...

  • Teledyne 102E - page 2

    ...

  • Teledyne 102E - page 3

    M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) TABLE OF CONTENTS 1. PREFACE ..................................................................................................................... ................. 1 1.1. Reference Numb er ing convention ..................................................................................... ...

  • Teledyne 102E - page 4

    M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) 8. INSTRUMENT MAINTENANCE ..................................................................................................... 3 9 8.1. Additional and Upd ate d Maintenance Proced ures ........................................................................ 40 8.1.1. Maintai ning the SO 2 ...

  • Teledyne 102E - page 5

    M102E/M501 TRS PREFACE (Addendum to M101E Manual - P/N 04740 Rev A) LIST OF FIGURES Figure 3-1: M 102E Internal Lay out ................................................................................... 7 Figure 3-2: M501 -TRS Internal L ayout............................................................................... 7 Figure 3-3: Internal Pne ...

  • Teledyne 102E - page 6

    ...

  • Teledyne 102E - page 7

    M102E/M501 TRS PREFACE (Addendum to M101E Manual - P/N 04740 Rev A) 1. PREFACE NOTE The information contained in t his addendum is pertinent to M102E anal yzers running software revisi on A.2. Some or all of the in formati on may not be applicable t o previous revision of that soft ware. The software revision your analyzer is ru nning is di splayed ...

  • Teledyne 102E - page 8

    PREFACE M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) 1.1. Reference Numbering convention Unless otherwise specified, chapter, section, figu re and table reference num bers referred to within this text are relative to thi s document. EXAMPLE: “Figure 2- 1” refers to the figure, within this document , labeled as 2-1. References to ...

  • Teledyne 102E - page 9

    M102E/M501 TRS SPECIFICATIONS, APPROVALS AND WARRANTY (Addendum to M101E Manual - P/N 04740 Rev A) 2. SPECIFICATIONS, APPROVALS AND WARRANTY 2.1. Specifications There are no significant differenc es between the performance specif ications for the M102E and the M102E as listed in Section 2.1 of the M101 E Manual - P/N 04740 Rev A. 2.1.1. M501-TRS Sp ...

  • Teledyne 102E - page 10

    SPECIFICATIONS, APPRO VAL S AND WARRANTY M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) • Sample filter: Equipped with PTFE filter element in the in ternal filter assembly. • Sample flow of 650 +/- 65 cc/min. • Vacuum pump (internal or external) capable of 14"Hg Absolute pressure @ 1 slpm or better. • Software settings: Dy ...

  • Teledyne 102E - page 11

    M102E/M501 TRS GETTING STARTED (Addendum to M101E Manual - P/N 04740 Rev A) 3. GETTING STARTED 3.1. Unpacking the M102E Unpack the M102E as per the directions ins Se ction 3.1 of the M101E Manual - P/N 04740 Rev A. 1. There are no shipping screws to be removed in the M102 E. 3.2. Unpacking the M501-TRS 2. Inspect the shipping package for external d ...

  • Teledyne 102E - page 12

    GETTING STARTED M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) 3.2.1. M501-TRS Ventilation Clearance: Whether the M501-TRS is set up on a be nch or installed into an inst rument rack, be sure to leave sufficient ven tilation clearance. AREA MINIMUM REQUIRED CLEARANCE Back of the instrument 10 cm / 4 inches Sides of the instrument 2.5 c ...

  • Teledyne 102E - page 13

    M102E/M501 TRS GETTING STARTED (Addendum to M101E Manual - P/N 04740 Rev A) 3.3. Internal Layouts Figures 3-1 & 3-3 supersede Figure 3-9 of the M101E Manual - P/N 04740 Rev A. Front Pane l UV Source La p Particu late F ilter React ion Ce ll Hydro carbo n Scrubb er Hidden from vi ew bene ath Reaction Cell PMT Housin g PMT Pream p PCA PMT Coolin ...

  • Teledyne 102E - page 14

    GETTING STARTED M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) 3.4. Internal Pneumatic Flow of the M102E & the M501-TRS Figure 3-3 shows th e internal pneumatic flow of the M102E in its Stan dard configuration. For information on in struments in which one of t he various zero/span valve opt ions refer to Figures 5- 2 and 5-3. 2 3 1 ...

  • Teledyne 102E - page 15

    M102E/M501 TRS GETTING STARTED (Addendum to M101E Manual - P/N 04740 Rev A) 3.5. Rear Panel Layout for the M102E & M501-TRS Figures 3-4 & 3-5 supersede Figure 3-2 of the M101E Manual - P/N 04740 Rev A. Figure 3-4: M102E Rear Panel Layout 5 A mp Slow -Blow Fuse Al a rm O u t p ut Connect ions Figure 3-5: M501-TRS Rear Panel L ayout 05514 Rev ...

  • Teledyne 102E - page 16

    GETTING STARTED M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) 3.6. Initial Setup 3.6.1. Electrical Connections: The electrical connections for the M102E are the sa me as those described in Section 3.1.1 of the M101E Manual - P/N 04740 Rev A except for the test channel analog output: 3.6.1.1. M102E Analog Output Connections This sectio ...

  • Teledyne 102E - page 17

    M102E/M501 TRS GETTING STARTED (Addendum to M101E Manual - P/N 04740 Rev A) • TO change these settings, see Sections 6. 9.4 and 6.7 of the M101E Manual - P/N 04740 Rev A respectively. 3.6.1.2. M501-TRS Alarm Output Connections The rear panel of the M501-TRS includes a termin al strip by which connect ions can be made to the converters internal te ...

  • Teledyne 102E - page 18

    GETTING STARTED M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) FROM ANALYZER Sample gas enters the M501-TRS from the M102E via this port. TO ANALYZER Sample gas leaves the M501-TRS to return to the M102E via thi s port. MODEL 102E Sample Zero Air Exhau st Span MODEL 701 Zero Ai r Genera tor VENT Calibrat ed span GA S (At hig h concentr ...

  • Teledyne 102E - page 19

    M102E/M501 TRS GETTING STARTED (Addendum to M101E Manual - P/N 04740 Rev A) CAUTION The exhaust from th e instrument needs to be vented outside the immediate area or shelter surrounding the instru ment and conform to all safety requirements using a maximum of 10 meters of 1/4” PT FE tubing. 9. Attach the sample line to the sampl e inlet port. Ide ...

  • Teledyne 102E - page 20

    GETTING STARTED M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) Table 3-4: NIST-SRM's Availa ble for Traceability o f H 2 S & S O 2 Calibration Gases NIST-SRM 4 TYPE NOMINAL CONCENTRATION 2730 2731 Hydrogen sulfide in N 2 Hydrogen sulfide in N 2 5000 ppb 20 ppm ZERO AIR • A gas that is similar in chemical composit ion to the ...

  • Teledyne 102E - page 21

    M102E/M501 TRS GETTING STARTED (Addendum to M101E Manual - P/N 04740 Rev A) Source of SAMPLE G as V ENT if i nput is pressurize d Zero / S p an Valves – O p tion 50 MODEL 700 Gas Dilution Calibrator (with O 3 generato r option) VENT Calibra ted SO 2 or H 2 S gas (At high concentrat ion) MODEL 102E From Co n verter Sam p le Zero Air Exha ust S p a ...

  • Teledyne 102E - page 22

    GETTING STARTED M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) Source o f SAMPLE G as VENT if in put is p ressurized MODEL 700 Gas Dilution Calibrator (with O 3 generator option) VENT Calibrate d H 2 S gas (At high concentra tion) MODEL 102E From Con verter Sam p le Zero Air Exhaus t M501-TRS To Converte r From Analy ze r To Anal yze r ...

  • Teledyne 102E - page 23

    M102E/M501 TRS GETTING STARTED (Addendum to M101E Manual - P/N 04740 Rev A) 3.7. Initial Operation 3.7.1. Startup / Warm Up of the M102E Startup proc edures and warm up behavior of the M102E are identical to those described in Sections 3.2.1 and 3.2.2 of the M1 01E Manual - P/N 04740 Rev A . Possible Warning Messages at Start-Up Warning messages fo ...

  • Teledyne 102E - page 24

    GETTING STARTED M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) 3.7.3. Startup / Warm Up of the M501-TRS After electrical and pneumatic conn ections are ma de, turn on the instr ument and pump powe r. The exhaust fan s hould start. The M501-TRS’ temperature controller is preprogrammed at the factory so no special setup operation is re ...

  • Teledyne 102E - page 25

    M102E/M501 TRS GETTING STARTED (Addendum to M101E Manual - P/N 04740 Rev A) 3.8. Initial Calibration Initial calibr ation of the M102E should be performed with : • Zero air supplied by a zero air generator such a s the Te ledyne In struments’ M701; • Calibrated H 2 S span gas of the appr opriate concentration: • With external pneumatic conn ...

  • Teledyne 102E - page 26

    ...

  • Teledyne 102E - page 27

    M102E/M501 TRS OPTIONAL HARDWA RE AND SOFTW ARE (Addendum to M101E Manual - P/N 04740 Rev A) 4. OPTIONAL HARDWARE AND SOFTWARE This section includes descriptions of the hardwa re and software options available for the Model 102E analyzer and M501-TRS co nverte r that are different from or not included in Chapter 5 of the M101E Manual - P/N 04740 Re ...

  • Teledyne 102E - page 28

    OPTIONAL HARDWA RE AND SOFTW ARE M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) 3 2 1 SAMPLE/CA L V ALVE ZERO/SPAN VALVE 3 2 1 2 3 1 SPAN G AS INLET ZERO A IR INLET VACUUM MANIFOLD FLOW CONTROL ASSY EXHAU ST TO OUTE R LAYER OF KICKE R SAMP L E FI LT ER M102E INS TR UMENT CHASSIS EXHAUST GAS OUTLE T KICKER EXHAUST TO P UMP HYDROCARB ON ...

  • Teledyne 102E - page 29

    M102E/M501 TRS OPTIONAL HARDWA RE AND SOFTW ARE (Addendum to M101E Manual - P/N 04740 Rev A) ` FLOW SENSOR FLO W / PRESS URE SENSOR P C A SAMPLE PRESSURE SENSOR EXHAUST T O OUTER L AYE R OF KICKE R 3 2 1 SAMPLE/C AL V ALVE ZERO/SPAN VALVE 3 2 1 2 3 1 ZERO A IR IN LE T VACUUM MANIFOLD CRITI CAL FLOW ORIFICE SAMPLE FILTER M102E INS TR UMENT CHASSIS E ...

  • Teledyne 102E - page 30

    OPTIONAL HARDWA RE AND SOFTW ARE M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) 4.3. Additional Manuals 4.3.1. Printed Manuals (P/N 049880000) Additional printed copies of this addendum are avai lable from Teledyne Instrume nts 4.3.2. Addendum on CD (Part number 049880200) This addendum is also available on CD. The electr onic document ...

  • Teledyne 102E - page 31

    M102E/M501 TRS M102E OPERATING INSTRUCTIONS (Addendum to M101E Manual - P/N 04740 Rev A) 5. M102E OPERATING INSTRUCTIONS NOTE For th e most pa rt the op eratio n instru ction fo r the M102 Eare the s ame as tho se described in Chapt er 6 of the M101E Manual - P/N 04740 Rev A with the exception that the terms “TRS” & “total reduc ed sulfur ...

  • Teledyne 102E - page 32

    M102E OPERATING INSTRUCTIONS M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) The output, labeled A3 is special. It can be set by th e user (see Section 6.9.10 of the M101E Manual - P/N 04740 Rev A) to output many of the parameters accessible through the <TST TST> keys of the units Sampl e Display. Output A4 is not available on the ...

  • Teledyne 102E - page 33

    M102E/M501 TRS M102E OPERATING INSTRUCTIONS (Addendum to M101E Manual - P/N 04740 Rev A) 5.2.2. M102E Test Channel Output The following table supercedes Table 6- 14 of the M101E Manual - P/N 04740 Rev A Ta bl e 5-3: Test P arameters Available for Analog Output A4 TEST CHANNEL TEST PARAMETER RANG E 1 NONE Test channel is turned off PMT READING 0-500 ...

  • Teledyne 102E - page 34

    M102E OPERATING INSTRUCTIONS M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) 5.4. Remote Operation of the Analyzer 5.4.1. Control Inputs The description of the control inputs in Section 6.12.1.2 of the M101 E Manual - P/N 04740 Rev A in correctly shows an external lo w span cal input. This is not correct. Neither the M102E nor the M102E ...

  • Teledyne 102E - page 35

    M102E/M501 TRS M102E OPERATING INSTRUCTIONS (Addendum to M101E Manual - P/N 04740 Rev A) CONTRO L IN - + 5 VDC Power Supply LOW SPA N ZERO SPAN A B C D E F U + Figure 5-3: Control Inputs wi th external 5 V power supply 5.4.2. Using the M102E with a Hessen Protocol Network 5.4.2.1. M102E Hessen Protocol Gas ID List. The default Hessen Gas Id’s for ...

  • Teledyne 102E - page 36

    M102E OPERATING INSTRUCTIONS M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) 5.4.2.2. Setting Hessen Protocol Status Flags The following table supercedes Table 6- 29 of the M101E Manual - P/N 04740 Rev A/ Table 5-6: Default He ssen St atus Bit Assignments STATUS FLAG NAME DEFAULT BIT ASSIGNMENT WARNING FLAGS SAMPLE FLOW WARNING 0001 PMT ...

  • Teledyne 102E - page 37

    M102E/M501 TRS M501-TRS OPERATING INSTRUCTI ONS (Addendum to M101E Manual - P/N 04740 Rev A) 6. M501-TRS OPERATING INSTRUCTIONS CAUTION ! DO NOT OPERATE WITHO UT THE COVER OF THE M 501TS CONVERTER INSTALLED. OVEN TEMPERATURE WILL NOT REGUL ATE PROPERLY WITHOUT THE COVER IN PLACE. NOTE: Changing the Converter te mperature from the valu e preprogramm ...

  • Teledyne 102E - page 38

    M501-TRS OPERATING INSTRUCTIONS M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) Table 6-1: M501-TRS Temperatur e Controls and Definiti ons NAME FUNCTION Main Display A 4-digit, 7 segment LED display on wh ich the current value of the PV and the SV as well as error codes and programming parameters and data are all displayed. Process valu ...

  • Teledyne 102E - page 39

    M102E/M501 TRS M501-TRS OPERATING INSTRUCTI ONS (Addendum to M101E Manual - P/N 04740 Rev A) 6.3. To Manually Adjust the Converter Oven Temperature: CAUTION ! DO NOT SET THE TEM PERATURE HIGHER THAN 1050 OC 1. Set the main display to show the current value of t he set variable by pressing the PV/SV mode key. 2. To set each digit: a. Press the up-ar ...

  • Teledyne 102E - page 40

    M501-TRS OPERATING INSTRUCTIONS M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) 6.4. Autotune the Temperature Controller: The M501-TRS controller includes an auto tune feat ure which allows the controller to find and set optimum values for various process control parame ters so that the controller can establish and maintain the converte ...

  • Teledyne 102E - page 41

    M102E/M501 TRS M501-TRS OPERATING INSTRUCTI ONS (Addendum to M101E Manual - P/N 04740 Rev A) 6.4.2. Aborting the Autotune Process: 1. Press the DATA key once. The display will show (1). 2. Press the 1’s UP key once. The will begin blinkin g 3. Press the DOWN key on ce. The display will show (zero). 4. Press the ENTER key once. 5. Press the PV/SV ...

  • Teledyne 102E - page 42

    ...

  • Teledyne 102E - page 43

    M102E/M501 TRS CALIBRATION PROCEDURES (Addendum to M101E Manual - P/N 04740 Rev A) 05514 Rev A1 37 7. CALIBRATION PROCEDURES 7.1. M102E Calibration Calibration of the M102E should be performed according to the proce dures described in Chapters 7 & 8 of the M101E Manual - P/N 04740 Rev A. NOTE It is recommended that the M102E be cali brated in T ...

  • Teledyne 102E - page 44

    ...

  • Teledyne 102E - page 45

    M102E/M501 TRS INSTRUMENT MAINTENANCE (Addendum to M101E Manual - P/N 04740 Rev A) 05514 Rev A1 39 8. INSTRUMENT MAINTENANCE The following table superc edes Table 9-1 of the M101E Manual - P/N 04740 Rev A Ta bl e 8-1: M102E Prev entive Maintenance Schedule ITEM ACTION FREQUENCY CAL CHECK M101E MANUAL SECTION DATE PERFORMED M501 SO2 scrubber Replace ...

  • Teledyne 102E - page 46

    INSTRUMENT MAINTENANCE M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) 8.1. Additional and Updated Maintenance Procedures The following procedures need to be performed re gularly as part of the standard maintenance of the Model 102E. 8.1.1. Maintaining the SO 2 Scrubber This section REPLACES Section 9.3.3 of t he M101E Manual - P/N 0474 ...

  • Teledyne 102E - page 47

    M102E/M501 TRS INSTRUMENT MAINTENANCE (Addendum to M101E Manual - P/N 04740 Rev A) 8.1.1.2. Checking the Func tion of the SO 2 Scrubber To check to see if your SO 2 scrubber is operating properly perform th e following test: 1. Set the analyzer for TRS gas measurement mode (see 6.8.1 of the M101E Manual - P/N 047 40 Rev A). 2. Set the reporting ran ...

  • Teledyne 102E - page 48

    ...

  • Teledyne 102E - page 49

    M102E/M501 TRS THEORY OF OPERATION (Addendum to M101E Manual - P/N 04740 Rev A) 9. THEORY OF OPERATION The M102E is a modified M101E which, when used in conjunction with a M501-TRS determines the concentration of total reduced s ulfur (TRS), in a sample gas drawn through the instrument In most ways the theory of operation of the M102 E & M501-T ...

  • Teledyne 102E - page 50

    THEORY OF OPERATION M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) nm. Th e SO 2 molecules absorbs some of energy from th e UV light causing one of the electrons of each of the affected molecules to move to a higher energy orbital state. * 2 SO hv SO Ia nm 214 2 ⎯ ⎯→ ⎯ + (Equation 9-2) The amount of SO 2 converted to excited S ...

  • Teledyne 102E - page 51

    M102E/M501 TRS THEORY OF OPERATION (Addendum to M101E Manual - P/N 04740 Rev A) The amount of det ectable UV g iven off by the decay of the SO 2 * is affected by the rate at wh ich this reaction occurs ( k ). ( ) * SO k F 2 = (Equation 9-5) Where: F = the amount of fluorescent li ght given off. k = The rate at which the SO 2 * decays into SO 2. SO ...

  • Teledyne 102E - page 52

    THEORY OF OPERATION M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) 9.2. The UV Light Path The following in formation is in addition t o that contained in Section 10.2 of the M101E Manual - P/N 04740 Rev A. 9.2.1. UV Lamp Shutter & PMT Offset Inherent in the operation of both the reference de tector an d the PMT are minor electroni ...

  • Teledyne 102E - page 53

    M102E/M501 TRS THEORY OF OPERATION (Addendum to M101E Manual - P/N 04740 Rev A) 9.4. Electronic Operation 9.4.1. Sensor Module This Section replaces Section 10.4.2 of t he M101E Manual - P/N 04740 Rev A. Electronically, the M102E sen sor module is a grou p of components that: create the UV l ight that initiates the fluorescence reaction between SO ...

  • Teledyne 102E - page 54

    THEORY OF OPERATION M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) 9.4.1.1. Sample Chamber The main electronic components of the sample chamber are the refe rence detector(see Section 10.2.2 of the M101E Manual - P/N 04740 Rev A ); th e UV Lamp (see Se ction 10.2.1 of the M101E Manual - P/N 04740 Rev A) and its electronically operated ...

  • Teledyne 102E - page 55

    M102E/M501 TRS THEORY OF OPERATION (Addendum to M101E Manual - P/N 04740 Rev A) 9.4.2. M501-TRS electronics Electronically the M501-TRS is a si mple device. The nucleus of t he instrument is a programmable, P-I-D temperature controller which manages the temperature of the instruments’ A C powered converter oven based on analog input from K-ty pe ...

  • Teledyne 102E - page 56

    THEORY OF OPERATION M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) 9.4.2.2. Temperature Alarms and Alarm Output The M501-TRS’ controller has two user settable alar m points: High Alarm and Low Alarm. A single SPST alarm output is tr iggered should the PV rise above th e set level of the high alarm poi nt or fall below the lev el of t ...

  • Teledyne 102E - page 57

    M102E/M501 TRS TROUBLESHOOTING & REPAIR (Addendum to M101E Manual - P/N 04740 Rev A) 10. TROUBLESHOOTING & REPAIR This section includes v arious troubleshooting and repair in formation that is eith er in addition to that included in Chapter 11 of th e M101E Manual (P/N 04740 Rev A) CAUTION The operations outlined in t his chapter mu st be p ...

  • Teledyne 102E - page 58

    TROUBLESHOOTING & REPAIR M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) 10.1.2. Fault Diagnosis with Test Functions The Following table supercedes Table 11. 2 of the M101E Manual - P/N 04740 Rev A. Table 10-2: Test Functions - Po ssible Causes for Out-Of- Rang e Values TEST FUNCTION NOMINAL VALUE(S) POSSIBLE CAUSE( S) STABIL ≤ 1 ...

  • Teledyne 102E - page 59

    M102E/M501 TRS TROUBLESHOOTING & REPAIR (Addendum to M101E Manual - P/N 04740 Rev A) 10.2. M501-TRS Trouble shooting 10.2.1. TRS Converter Not Heating: Problems with heating the If the TRS co nverter oven can have several causes. • The “UUUU” error code will is displayed on the M501-TRS temperature controller display indicating a problem ...

  • Teledyne 102E - page 60

    TROUBLESHOOTING & REPAIR M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) 10.4. Subsystem Checkout In addition to the informatio n contained in Section 11.5 of the M101E Manual - P/N 04740 Rev A, the following diagnosti c procedures are useful for troubleshooting and diagnosi ng problems with your M102E and M501-TRS. 10.4.1. Checking ...

  • Teledyne 102E - page 61

    M102E/M501 TRS TROUBLESHOOTING & REPAIR (Addendum to M101E Manual - P/N 04740 Rev A) 10. If TRS Æ SO 2 converter efficiency i s below 90% check for one of the foll owing possible causes: • Pneumatic leak • Perform a leak check (with the M501-TRS connected) as described in Section 11.5.1 of the M101E Manual - P/N 04740 Rev A. • Plugged or ...

  • Teledyne 102E - page 62

    TROUBLESHOOTING & REPAIR M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) Lamp Positioning – The UV output level of the lamp is not even across the entire length of the lamp. Some portions of th e lamp shine slightly more brightly than others. At the factory the position of the UV lamp is adjusted to optimize the amount of UV light ...

  • Teledyne 102E - page 63

    M102E/M501 TRS TROUBLESHOOTING & REPAIR (Addendum to M101E Manual - P/N 04740 Rev A) UV Lamp B racket Mounting Screws Shutter Housi ng Shutter Assy UV Filter Retain er & Lens Housing UV Lamp Power Supp ly W ire s Thumb Screw DO NOT use Lamp Ca p to adjust Lamp position Reaction Cell Adjust Lamp Position by graspi ng l amp body ONLY Figure 1 ...

  • Teledyne 102E - page 64

    TROUBLESHOOTING & REPAIR M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) 9. Finger tighten the th umbscrew. NOTE: DO NOT over-tighten the thumbscrew. 10. Perform a lamp calibration procedure (see Section 6.9.7 of the M101E Manual - P/N 04740 Rev A) and a zero point and span point calibra t ion (see Chapter 7 of the M101E Manual - P/ ...

  • Teledyne 102E - page 65

    M102E/M501 TRS TROUBLESHOOTING & REPAIR (Addendum to M101E Manual - P/N 04740 Rev A) 5. Carefully remove the UV filter. 6. Install the UV filter. Handle carefully and never t ouch the filter’s surface. The UV filter’s wider ( ring ) side should be facing out. Insta ll the UV fil ter retainer and tighten screws. 7. Install the shutter cove r ...

  • Teledyne 102E - page 66

    TROUBLESHOOTING & REPAIR M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) 3. Remove the reaction cell assembly. 4. Remove the two connectors on the PMT housin g end plate facing towa rds the front panel. 5. Remove the end plate itself (4 scre ws with plastic washers). R 6. Remove all of the desiccant ba gs inside the PMT housing. 7. ...

  • Teledyne 102E - page 67

    M102E/M501 TRS TROUBLESHOOTING & REPAIR (Addendum to M101E Manual - P/N 04740 Rev A) 15. Re-insert the PMT/HVPS subassembly. • Don’t forget the gasket between HVPS and PMT . • Use new plastic screws to mount the PM T assembly on the PMT cold block. 16. Insert the new desiccant bags. 17. Carefully replace the end plate. • Make sure that ...

  • Teledyne 102E - page 68

    TROUBLESHOOTING & REPAIR M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) 6. Locate the Preamp board (see Figure 3-1). 7. Locate the Following Components On the Preamp board (see Figure 10-4): • HVPS coarse adjustment switch (R ange 0-9, then A-F) • HVPS fine adjustment swi tch (Range 0-9, then A-F) • Gain adjustment potent iom ...

  • Teledyne 102E - page 69

    M102E/M501 TRS TROUBLESHOOTING & REPAIR (Addendum to M101E Manual - P/N 04740 Rev A) If a reporting range other than 50 0 ppb is u sed in this pro cedure : Use a span gas equal to 80% of the report ing range and adjust the PMT to a target NORM PMT value of twice the ppb value of the span gas. EXAMPLE If the reporting range is 800 ppb: Use 640 p ...

  • Teledyne 102E - page 70

    TROUBLESHOOTING & REPAIR M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) 2. Allow it to cool to room temperatur e. This may take up to 30 minutes. 3. Remove the instruments top cover (s ee Section 3.2 of this addendum) 4. Remove the four screws holdi ng the converter cover in place. 5. Carefully lif t the converter cover away. 6. Lo ...

  • Teledyne 102E - page 71

    M102E/M501 TRS TROUBLESHOOTING & REPAIR (Addendum to M101E Manual - P/N 04740 Rev A) DO NOT manually alter the PID parameters of the M 501-TRS temperatur e Controller unless directed to do so by Teledyne Instruments customer service per sonnel. In the event that the temperat ure controller of the M501-TRS mu st be replaced some initial programm ...

  • Teledyne 102E - page 72

    TROUBLESHOOTING & REPAIR M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) Table 10-3 – Temperature C ontrolle r – Primar y Parameter Settings DISPLAY PARAMETER NAME SET TO COMMENTS Proportional Band 11 Sets the bandwidth of the proportional control function to ± 11% of full scale Integral time 10 Sets the reaction time for the p ...

  • Teledyne 102E - page 73

    M102E/M501 TRS TROUBLESHOOTING & REPAIR (Addendum to M101E Manual - P/N 04740 Rev A) Table 10-4 – Temperature C ontrolle r – Primar y Parameter Settings DISPLAY PARAMETER NAME SET TO COMMENTS OFF 0 Sets the controller to reverse action (hotter temperatures = less heating; lower temperatures = more heating) and turns off the heater should th ...

  • Teledyne 102E - page 74

    TROUBLESHOOTING & REPAIR M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) User Notes: 68 05514 Rev A1 ...

  • Teledyne 102E - page 75

    M102E/M501 TRS APPENDIX A - Version Specific Software Document ation (Addendum to M101E Manual - P/N 04740 Rev A) APPENDIX A - Version Specific Software Documentation APPENDIX A-1: Model 102E Software Menu Trees NOTE The menu tree struct ure for the M102E is nearly identical to th at of the M101E. Included here are menu trees, including s ome minor ...

  • Teledyne 102E - page 76

    APPENDIX A-1: M102E Software Menu Trees, Revisio n A.2 M102E/M501 TRS (Addendum to M101E Manual) APPENDIX A-1: M102 E Software Menu Tre es, Revision A.2 ZERO SPAN CONC SAMPLE <TST TST> RANGE STABIL PRES SAMP FL PMT NORM PMT UV LAMP LAMP RATIO STR. L GT DARK PMT DARK LAMP SLOPE OFFSET HVPS RCELL TEMP BOX TEMP PMT TE M P IZS TEMP 1 TEST 2 TIME ...

  • Teledyne 102E - page 77

    APPENDIX A-1: M102E Software Menu Trees, Revisio n A.2 M102E/M501 TRS (Addendum to M101E Manual) LOW HIGH ZERO SPAN CONC SAMPLE <TST TST> SETUP COMM DIAG VARS (Secondary Setup Menu) CFG DAS RANG PASS CL K MORE ( Primary Se tup Menu) Only appear if reporting range is s et fo r AUTO range mode. LOW HIGH ZERO LOW HIGH SPAN CO NC MSG 1,2 CLR 1,3 ...

  • Teledyne 102E - page 78

    APPENDIX A-1: M102E Software Menu Trees, Revisio n A.2 M102E/M501 TRS (Addendum to M101E Manual) . YES NO SAMPL E FLO W WAR NING BENCH T EMP WARNING SOURCE WAR N I NG BOX TEMP WARNING WHEEL TEM P WAR NING SAMPLE TE MP WARNING SAMPLE PRES SURE WAR NING INVALID CONC INSTRUME NT OFF IN MANUA L CALIBRA TION M ODE IN Z ERO C ALIB RA TIO N MO DE IN SPAN ...

  • Teledyne 102E - page 79

    X A-1: M102E Software Menu Trees, Revision A.2 M102E/M501 TRS (Addendum to M101E Manual) 515 Rev A.2 A-5 32 INTERNAL ANALOG ↓ VOLTAGE SIGNALS 56 (see Ap pendix A) CFG ACAL 1 CLK PASS RNGE DAS MORE COMM VARS 2 Only relevant to a n aly z ers with IZS options in sta lle d ANALO G OUTPUT LAMP CALIBRATION 0) EXT ZERO CAL 1) EXT SPAN CAL 2) MAINT MODE ...

  • Teledyne 102E - page 80

    APPENDIX A-2: Setup Variables For Se rial I/O, R evision A.2 M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) APPENDIX A-2: Setup V ariables For Se ria l I/O, Revision A.2 NOTE Setup Variabl es for the M102E are the sa me as those for the M 102E (see Appendix A-3 of the M101E Manual - P/N 04740110 Rev A) with the following excepti o ns: ...

  • Teledyne 102E - page 81

    M102E/M501 TRS APPENDIX A-3: War n i ngs and Test Functions, Revi sion A.2 (Addendum to M101E Manual - P/N 04740 Rev A) APPENDIX A-3: Warnings and Test Functions, R evision A.2 NOTE Warning messages and test functions for the M102E are t he same as those for the M102E (see Appendix A-3 of the M101E Manual - P/N 0474 01 10 Rev A) with t he following ...

  • Teledyne 102E - page 82

    APPENDIX A-4: M102E Signal I/ O Definitions, Revision A.2 M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) APPENDIX A-4: M102E Signal I/O Definiti ons, Revision A.2 NOTE Signal I/O Definition s for the M102E are the same as those for the M102E (see Appendix A-4 of the M101E Manual - P/N 0474 0110 Rev A) with the followi ng exceptions: Ta ...

  • Teledyne 102E - page 83

    M102E/M501 TRS APPENDIX A-5: M102E iDAS Functions, Revision A.2 (Addendum to M101E Manual - P/N 04740 Rev A) APPENDIX A-5: M102E iDAS Func tions, Revision A.2 NOTE iDAS Trigger Events and functi ons for the M102E are the s a me as those for the M 102E (see Appendix A-5 and A-6 of the M1 01E Manual - P/N 0474 0110 Rev A) wit h the following exceptio ...

  • Teledyne 102E - page 84

    APPENDIX A-5: M102E iDAS Functions, Revision A.2 M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) A-10 05515 Rev A.2 ...

  • Teledyne 102E - page 85

    M102E/M501 TRS APPENDIX B - M102E Spare Parts List (Addendum to M101E Manual - P/N 04740 Rev A) APPENDIX B - M102E Spare Parts List NOTE Spare parts for the M102E are t he same as those for the M101E (see App endix B of the M101E Manual - P/N 04740120 Rev A ) Spare parts availabl e for the M501-T RS are as follows: Table B-1: M102E Spare Parts List ...

  • Teledyne 102E - page 86

    APPENDIX B - M102E Spare Parts List M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) B-2 05516 Rev A ...

  • Teledyne 102E - page 87

    M102E/M501 TRS Warranty/Repair TELEDYN E Addendum to Appendix C M101E Manual (P/N 04740) Questionnaire Model 102E I NSTRUMENTS Advanced Poll uti on I nst r umentat i o n A Teledyne Techno logi es Com pany Company: _________________________ Contact Name: _____________________________ Phone Number: ___________ Fax Number: _____________ Email: _______ ...

  • Teledyne 102E - page 88

    M102E/M501 TRS Warranty/Repair TELEDYN E Addendum to Appendix C M101E Manual (P/N 04740) Questionnaire Model 102E I NSTRUMENTS Advanced Poll uti on I nst r umentat i o n A Teledyne Techno logi es Com pany Notes and further information: _____________________________________________________ ____________________________________________________________ ...

  • Teledyne 102E - page 89

    M102E/M501 TRS APPENDIX D - ELECTRONIC SCHEMATICS (Addendum to M101E Manual - P/N 04740 Rev A) APPENDIX D - ELECTRONIC SCHEMATICS The following drawing(s) are relevant to the M501-TRS. All drawings relevant t o the M102E are listed in Appendix D of the M101E Manual. Table D-1: List of I ncluded El ectronic Schematics DOCUMENT # DOCUMENT TITLE 03404 ...

  • Teledyne 102E - page 90

    APPENDIX D - ELECTRONIC SCHEMATICS M102E/M501 TRS (Addendum to M101E Manual - P/N 04740 Rev A) User Notes D-2 05518 Rev A ...

Manufacturer Teledyne Category TV Converter Box

Documents that we receive from a manufacturer of a Teledyne 102E can be divided into several groups. They are, among others:
- Teledyne technical drawings
- 102E manuals
- Teledyne product data sheets
- information booklets
- or energy labels Teledyne 102E
All of them are important, but the most important information from the point of view of use of the device are in the user manual Teledyne 102E.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Teledyne 102E, service manual, brief instructions and user manuals Teledyne 102E. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Teledyne 102E.

Similar manuals

A complete manual for the device Teledyne 102E, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Teledyne 102E by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Teledyne 102E.

A complete Teledyne manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Teledyne 102E - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Teledyne 102E, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Teledyne 102E, that we can find in the current document
3. Tips how to use the basic functions of the device Teledyne 102E - which should help us in our first steps of using Teledyne 102E
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Teledyne 102E
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Teledyne 102E in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Teledyne 102E?

Use the form below

If you did not solve your problem by using a manual Teledyne 102E, ask a question using the form below. If a user had a similar problem with Teledyne 102E it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)