English dropdown-ico

Manual CDA FW283

19 pages Not applicable
Download

Go to site of 19

Summary
  • CDA FW283 - page 1

    Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .cda.eu FW283 integrated under counter freezer Manual for Installation, Use and Maintenance ...

  • CDA FW283 - page 2

    2 Important The CD A Group L td cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CD A reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance. This appliance is not designed to be used by people (in ...

  • CDA FW283 - page 3

    3 This appliance has been manufactured to the strictest standards and complies with all applicable legislation, including Electrical safety (L VD) and Electromagnetic interference compatibility (EMC). P arts intended to come into contact with food conform to EEC/89/109 .4 IMPORT ANT INFORMA TION FOR CORRECT DISPOSAL OF THE PRODUCT IN A CCORD ANCE W ...

  • CDA FW283 - page 4

    4 Important Never store inflammable or explosive items and strong corrosive acids or alkalis in the appliance. This is a household appliance, which is produced in accordance with the national standard. It is intended for food storage only , not for storage of blood, medicine and biological products. T o prevent risk of fire, keep the appliance aw ...

  • CDA FW283 - page 5

    5 Before first use Y ou must allow the freezer to settle for at least twenty four hours prior to switching the power on. It is recommended that you clean the interior of the appliance prior to first use, using a solution of bicarbonate of soda and warm water and then thoroughly drying the interior . The freezer may have an odour to it at first u ...

  • CDA FW283 - page 6

    6 Use Freezer • The freezer compartments are designed to store only frozen food. • Never put hot or warm foods in the freezer , allow them to cool fully before putting them into the freezer . • Follow the instructions on the food packaging for storage of frozen food. If no information is provided, foods should not be stored for more than thre ...

  • CDA FW283 - page 7

    7 Control panel Thermostat dial The thermostat can be set between (least cold) and 5 (coldest) When introducing large amounts of fresh food into the freezer , turn the thermostat dial to position 5. After 24 hours, return the thermostat dial to its usual position. fig. 1 1 2 3 4 5 ...

  • CDA FW283 - page 8

    8 Defrosting the freezer Do not use heaters or defrosting sprays in this appliance. • Never use any metallic or sharp objects to remove the ice as this could damage the lining. • The freezer compartment should be defrosted regularly to ensure the most ecient running of the freezer . • Once the ice is more than 5mm thick, the freezer should ...

  • CDA FW283 - page 9

    9 T roubleshooting If you have any problems with your appliance, you should check the troubleshooting prior to calling CD A Customer Care to prevent unnecessary service calls and potential cost. If the appliance is not working • Chec k there is power to the appliance: • The house fuses are intact and the fuse in the plug has not blown. • The ...

  • CDA FW283 - page 10

    10 fig. 2 KIT 1 2 3 4 5 6 9 10 7 8 9 10 Installation This appliance must never be installed close to heat sources i.e. heating elements, radiators, cookers or in damp places. The appliance should be mounted on a piece of wood (for example a section of worktop or kitchen carcass) if a raised oor is to be tted, if the kitchen oor is to be t ...

  • CDA FW283 - page 11

    11 fig. 5 fig. 3 fig. 4 11 11 600 min 550 820- 890 595 548 min 25 819- 889 100- 170 5 6 11 11 Installation Fig. 3 - Dimensions of the appliance Fig. 4 - Fitting the worktop bracket R emove the screw (5) on the top of the appliance, locate the top bracket(6) and fix the bracket with screw(5). Fig. 5 - Fitting the spacer piece T ake out the space ...

  • CDA FW283 - page 12

    12 9 9 fig. 8 Installation Fig. 6 - Adjusting the appliance height The height of the appliance can be adjusted by the help of adjustable feet to fit the furniture height. Use a spirit level to ensure the appliance is level. Fig. 7 - Aligning the appliance Slide the appliance into the kitchen unit and align the hinge surface with front surface of ...

  • CDA FW283 - page 13

    13 2 1 B-C fig. 11 Installation Fig. 9 - Fitting the decor door bracket Unscrew and remove the nuts and washers from the appliance door . Place fixing bracket on the appliance door by inserting the holes to adjustment bolts. Dimension B= Measure from the underside surface of kitchen unit to the bottom of fixing bracket. Dimension C= Measure from ...

  • CDA FW283 - page 14

    14 fig. 14 Installation Fig. 12 - Aligning the decor door Close the door and check the alignment with the other unit doors. Adjust the decor door by screwing or unscrewing the adjustment bolts for vertical adjustment and by the help of the slots on the fixing bracket for other directions. L ock the screws into place as shown in 10 .2. Fig. 13 - F ...

  • CDA FW283 - page 15

    15 Installation Fig. 17 - Fitting the plinth Fit the plinth section, providing minimum 25 mm gap between the cabinet door and fix it. Never cover over the ventilation slots. Once installed the plinth must not block the ventilation slots in the appliance. This may require cutting the plinth down. Failure to ensure adequate ventilation may invalidat ...

  • CDA FW283 - page 16

    16 Electrical information W arning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug. T o change a fuse in this type of plug, follow the steps below: 1. R emove the fuse cover and fuse. 2. Fit replacement 13A fuse, A ST A approved to BS 1362 type, into the fuse cover . 3. R eplace f ...

  • CDA FW283 - page 17

    17 As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: • The wire which is coloured GREEN and YELL O W must be connected to the terminal which is marked with letter (E) or by the Earth symbol or coloured GREEN and YELL O W . • T ...

  • CDA FW283 - page 18

    18 ...

  • CDA FW283 - page 19

    19 ...

Manufacturer CDA Category Freezer

Documents that we receive from a manufacturer of a CDA FW283 can be divided into several groups. They are, among others:
- CDA technical drawings
- FW283 manuals
- CDA product data sheets
- information booklets
- or energy labels CDA FW283
All of them are important, but the most important information from the point of view of use of the device are in the user manual CDA FW283.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals CDA FW283, service manual, brief instructions and user manuals CDA FW283. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product CDA FW283.

Similar manuals

A complete manual for the device CDA FW283, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use CDA FW283 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of CDA FW283.

A complete CDA manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual CDA FW283 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the CDA FW283, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the CDA FW283, that we can find in the current document
3. Tips how to use the basic functions of the device CDA FW283 - which should help us in our first steps of using CDA FW283
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with CDA FW283
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of CDA FW283 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning CDA FW283?

Use the form below

If you did not solve your problem by using a manual CDA FW283, ask a question using the form below. If a user had a similar problem with CDA FW283 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)