English dropdown-ico

Manual EverFocus EDR-1610A

83 pages 2.29 mb
Download

Go to site of 83

Summary
  • EverFocus EDR-1610A - page 1

    INSTALLATION / OPERATION EDR-910A 9-channel Digital Video Reco rder EDR-910D 9-channel Digital Video Reco rder with internal DVD-RW drive EDR-1610A 16-channel Digital Video Recorder EDR-1610D 16-channel Digital Video Recorder with internal DVD-RW drive ...

  • EverFocus EDR-1610A - page 2

    EDR910_1610_ma_en_rev1 00 -2 - Safety warnings Safety warnings To avoid any damage, pl ease consider the following safety warnings: Never place the recorder near to heaters, fu rnaces, other heat sources or under direct solar irradiation. Operate the device only in locat ions providing the tolerable operat ing temperature range 0°C~40°C. Make sur ...

  • EverFocus EDR-1610A - page 3

    EDR910_1610_ma_en_rev1 00 -3 - TABLE OF CONTENTS Safety warnings .............................................................................................- 2 - 1. INTRODUCTION ..........................................................................................- 5 - 1.1 FEATURES ............................................................. ...

  • EverFocus EDR-1610A - page 4

    EDR910_1610_ma_en_rev1 00 -4 - 6. VIDEO EXPORT .........................................................................................- 58 - 7. CALL MONITOR SE TUP ..............................................................................- 60 - 8. DISPLAY SETTINGS ............................................................................... ...

  • EverFocus EDR-1610A - page 5

    EDR910_1610_ma_en_rev1 00 -5 - INTRODUCTION 1. INTRODUCTION The latest EverFocus digital video recorder generation is based on MPEG-4 compression technology, resultin g in enhanced recording capacity and improved network image transmission speed with high image quality. Comprehensive features and extended even t recording settings enable the almost ...

  • EverFocus EDR-1610A - page 6

    EDR910_1610_ma_en_rev1 00 -6 - 1.3 TECHNICAL DA TA Video format PAL Video input EDR 910: 9 x 1 Vpp FBAS, BNC, 75 Ohm EDR 1610: 16 x 1 Vpp FBAS, BNC, 75 Ohm Video output Main monitor: 1 Vpp FBAS, BNC at 75 Ohm Callmonitor: 1 x 1 Vpp FBAS, BNC at 75 Ohm 9/16 x loop-through outputs 1 Vpp FBAS, BNC at 75 Ohm Video compression MPEG-4 Recording resolutio ...

  • EverFocus EDR-1610A - page 7

    EDR910_1610_ma_en_rev1 00 -7 - Power consumption 50 W max. Dimensions 430 (W) x 72 (H) x 402,5 (D) mm Weight 6,42 kg Ambient temperature 0°C ~ +40°C Remote control Optional: IR remote control, RS-485 keyboard ...

  • EverFocus EDR-1610A - page 8

    EDR910_1610_ma_en_rev1 00 -8 - 1.4 FRONT PANEL OPERATING ELEMENTS Keys (1) REC: recording key (2) STOP: recording / playback stop (3) PLAY: playback (4) PAUSE: image freeze, stops playback for freeze mode (5) SEARCH: opens on-screen display fo r playback search (6) COPY: opens image export menu. In playba ck mode, the current playback posit ion is ...

  • EverFocus EDR-1610A - page 9

    EDR910_1610_ma_en_rev1 00 -9 - (11) ZOOM: In full screen mode: 2x electron ical zoom. Zoom screen can be moved through JOG . ENTER key changes the direction. Further zoom key actuation switches the el ectronical zoom off. In multiscreen mode: Image or ientation adjust ment. Use the JOG to adjust the image to the respective monitor type. ENTER switc ...

  • EverFocus EDR-1610A - page 10

    EDR910_1610_ma_en_rev1 00 - 10 - 1.5 CONNECTIONS (1) Main switch: Power switch, below IEC socket for 100 ~240 VAC power source (2) MAIN monitor: Main monitor for live and play back display and on-screen display (3) CALL monitor: CALL monitor out put. Spotmonitor for fu ll screen live display, sequence mode and alarm camera switching (4) Video input ...

  • EverFocus EDR-1610A - page 11

    EDR910_1610_ma_en_rev1 00 - 11 - 1.6 SCREEN DISPLAYS Here’s an overview of the screen displ ays appearing on the MAIN monitor: (1) Channel display: shows the selected video channel’s description (2) Event: Event display, may be channel- relat ed or global Channel-related types of event: Alarm: Display of an al arm triggered by alarm input conta ...

  • EverFocus EDR-1610A - page 12

    EDR910_1610_ma_en_rev1 00 - 12 - (3) SELECT: Within a multi screen view, the SELECT key activates the camera selection mode. The active camera field shows “S”. Use the JOG to switch betw een the camera fields. Use the channel keys 1~9 or 1~16 to switch the cha nnel. (4) PLAYBACK STAT US: The playback-relevant in formation are displayed in th is ...

  • EverFocus EDR-1610A - page 13

    EDR910_1610_ma_en_rev1 00 - 13 - INSTALLATION 2. INSTALLATION ATTENTION: The installation sh ould be effected by qualif ied person nel only. Conn ect power source only after having finished the further i nstallation. 2.1 Delivery scope Check the delivery scope (see 4.) befo re starting the installation. 2.2 Video connection installation Sample inst ...

  • EverFocus EDR-1610A - page 14

    EDR910_1610_ma_en_rev1 00 - 14 - 2.3 RS-485 keyboard installation All EDR910/1610 functions can be remote-controlled by the EKB 5 00 universal keyboard. Using the EEPbus protocol, digital video re corders, keyboards and speed domes can be installed on one single RS- 485 bus. One system can com prise up to 8 keyboards. 2.3.1 General RS-48 5 bus inst ...

  • EverFocus EDR-1610A - page 15

    EDR910_1610_ma_en_rev1 00 - 15 - If star wiring is inevitable, E DA 997A RS- 485 signal distributors may be used. The maximum system cable length can also be expanded by using these distributors, physically providing a new RS- 485 bus with 1200 m cable length each at every distributor output. In case the maximum number of 32 bus participants is exc ...

  • EverFocus EDR-1610A - page 16

    EDR910_1610_ma_en_rev1 00 - 16 - 2.3.2 RS-485 plug connecti on assignment The two RS-485 input RJ-45 plugs are looped through a nd pin-compatible. The following RJ-45 plug assignment has to be considered for connecti on: The following illustration sh ows the connector box assign ment of the optional EDA998 connection kit (connect or box, patch cabl ...

  • EverFocus EDR-1610A - page 17

    EDR910_1610_ma_en_rev1 00 - 17 - 2.3.4 EKB-500 conne ction to several DVRs For long distance installations connecting se veral DVRs, the use of the optional EDA998 connection kit is recommended: EKB 500 installation with several DVRs and EDA998 connection kit For further details on keyboard connecti on, please refer to the EKB 500 manual. RS-485 po ...

  • EverFocus EDR-1610A - page 18

    EDR910_1610_ma_en_rev1 00 - 18 - 2.4 Speed dome installat i on Speed dome or telemetry receiver pan/tilt /zoom control is available th rough web browser or the optional PowerCon software if the DV R is connected to a network. Local telemetry control is provided by the optional EKB 500 keyboard. ATTENTION : The basic RS-485 wiring rules described in ...

  • EverFocus EDR-1610A - page 19

    EDR910_1610_ma_en_rev1 00 - 19 - 2.5 Alarm input / ou tput installation The EDR910/1610 alarm inputs can be used for recording start or recording rate adjustment. Furthermore, alarm reactions such as camera sw itching to monitors, buzzer, e-mail and network alarm are available. An alarm output r elay can be switched if required. EDR910 provides 9 a ...

  • EverFocus EDR-1610A - page 20

    EDR910_1610_ma_en_rev1 00 - 20 - 2.6 PS/2 mouse installation EDR910/1610 may optional ly be controlled through USB wheel mouse which must be connected before system start-up. The mouse connector is the lower USB socket at the front panel. 2.7 Network connection EDR910/1610 DVRs pr ovide fast MPEG-4 format i mage transmission and networ k remote con ...

  • EverFocus EDR-1610A - page 21

    EDR910_1610_ma_en_rev1 00 - 21 - 2.7.3. Network system requirements Connection type: 100Base-T Max. required networ k bandwidth: 10 MBit Protocol types: TCP, UDP, SMTP, HTTP, NTP Required ports: for port conf iguratio n, please refer to NETWORK menu ...

  • EverFocus EDR-1610A - page 22

    EDR910_1610_ma_en_rev1 00 - 22 - 2.8 IR remote control extension The optional IR remote control EDA966 has a r ange of ~10m within the range of vision. This maximum range can be extended by using the EDA967 (10m) and EDA968 (20m) extension cables. Remote control extens ion with EDA967/968 2.9 Power connection Connect the DVR to the power source (10 ...

  • EverFocus EDR-1610A - page 23

    EDR910_1610_ma_en_rev1 00 - 23 - SETUP MENU 3. SETUP MENU All EDR DVR settings are carried out in the on-screen display. The MENU key starts the main menu. Press the MENU key again to leave the menu or to c hange from sub menu to a higher menu level. Use the JOG to select a menu ite m. Use the ENTER key to confi rm a selection and to proceed to the ...

  • EverFocus EDR-1610A - page 24

    EDR910_1610_ma_en_rev1 00 - 24 - 3.1 TIME / DATE MEN U Define the following setti ngs in the TIME / DAT E menu: (1) TIME FORMAT: Select either 12-hour o r 24-hour format for time di splay (2) TIME: Current time Hour: 00 ~ 23 (1 ~ 12 for 12-hour format) Minute : 00 ~ 59 Second: 00 ~ 59 (3) DATE FORMAT: Select the date display format: YYYY-MM-DD , MM ...

  • EverFocus EDR-1610A - page 25

    EDR910_1610_ma_en_rev1 00 - 25 - (7) END DATE: End of daylight saving time Select month: Use the JOG to adjust the month: Select week: Use the JOG to adjust the w eek of the selected month: Select day: Use the JOG to ad just the weekday: Adjust switching time: Select the switching time (F ROM) and the new time (TO). Central Europe daylight saving t ...

  • EverFocus EDR-1610A - page 26

    EDR910_1610_ma_en_rev1 00 - 26 - (10) TIME ZONE: Enter your local time zon e ( Germany, Austria, Switz erland: GMT+1). ATTENTION: The correct entry is compulsory for NTP sy nchronisation. (11) UPDATE INTERVAL: Time synchroni sation interval DAY MONTH WEEK ...

  • EverFocus EDR-1610A - page 27

    EDR910_1610_ma_en_rev1 00 - 27 - 3.2 CAMERA MENU Menu display for EDR-910, ED R1610 identical, but with 16 cameras. The most important recording operation se ttings are defined in the CAMERA menu. Before changing th e settings in this menu, recording has to be stopped. Each camera is set indivi dually: (1) NAME: Enter the video channel description ...

  • EverFocus EDR-1610A - page 28

    EDR910_1610_ma_en_rev1 00 - 28 - (5) REC QUALITY: Individual recording quality se tting for t his camera (within the resolution defined in RECOR DING menu): S U P E R I O R H I G H STANDARD BASIC L O W LOWER Using the VBR (Variable Bi t Rate) method, the storage requirement per image depends on the image’s colour and contrast content and captured ...

  • EverFocus EDR-1610A - page 29

    EDR910_1610_ma_en_rev1 00 - 29 - (7) SUMMARY: The SUMMARY menu item give s a summary on the settings for control purpose. Use the JOG to browse the indivi dual settings. ATTENTION: This menu does not allow any editing of settings. (8) COPY function Besides camera title, PTZ ID and INSTALLE D/COVERT, th e settings can be copied from one camera to an ...

  • EverFocus EDR-1610A - page 30

    EDR910_1610_ma_en_rev1 00 - 30 - 3.3 RECORDING MENU Define the following settings i n the recording menu: (1)TIME STAMP: ON: Recording is overlaid by time and date. OFF: Recording doesn’t provide time/date stamp. (2) TIME STAMP POS.: TOP: Time / date is displayed at the top screen margin. BOTTOM: Time / date is displayed at the bottom screen marg ...

  • EverFocus EDR-1610A - page 31

    EDR910_1610_ma_en_rev1 00 - 31 - 3.4 ALARM MENU Define the dry alarm contacts ’ attributes and the alarm re actions in the ALARM menu. For alarm contact pin assignment, please refer to appendi x D. Each contact is adjusted in dividually and selected f rom th e list on the left: (1) ALARM: ENABLE: Contact is activated. DISABLE: Contact is deactiva ...

  • EverFocus EDR-1610A - page 32

    EDR910_1610_ma_en_rev1 00 - 32 - (4) DURATION: Alarm duration for N.O. and N. C. c ontact types. Duration applies to r ecording, screen change, buzzer and output contact and is adjus table from 1~99 seconds. (5) ALARM OUTPUT: Output relay activation. 1: Output relay 1 is switched in case of alarm NONE: Output relay is deactivat ed. (6) ALARM EMAIL: ...

  • EverFocus EDR-1610A - page 33

    EDR910_1610_ma_en_rev1 00 - 33 - 3.5 MOTION DETECTI ON Define all mot ion det ection settings fo r th e individual cameras in th e MOT ION DETECTION menu. Use the JOG to select the cameras from the list on the left. (1) MOTION: ENABLE: Motion detection is activated. DISABLE: Motion detection i s deactivated. ATTENTION: Motion detection i s automati ...

  • EverFocus EDR-1610A - page 34

    EDR910_1610_ma_en_rev1 00 - 34 - (5) EMAIL: By selecting “ON” , an email is sent in ca se of motion alarm, containing the alarm message, the camera’s alarm image an d the DVR IP address as sende r. Define the email recipiant’s de tails in the NE TWORK menu. (6) BUZZER: Alarm buzzer activation ENABLE : Alarm buzzer is activated. DISABLE : Al ...

  • EverFocus EDR-1610A - page 35

    EDR910_1610_ma_en_rev1 00 - 35 - DISPLAY KEY FOR HELP (11) AREA SET UP With activated motion d etection, the sub me nu for setting up detection areas can be entered by pressing the SELECT key. Use the DISPLAY k ey t o show all function k eys available for th is menu at any time. Active areas are shown in green. Press the COPY key to start the sele ...

  • EverFocus EDR-1610A - page 36

    EDR910_1610_ma_en_rev1 00 - 36 - 3.6 VIDEO LOSS MENU Define the reaction upo n video signal loss for each camera i n this menu: (1) VLOSS: ENABLE: Video loss detection is activated. DISABLE: Video loss detection is deactivated. (2) DURATION: Alarm duration. Duration applie s to buzzer an d output contact and is adjustable from 1~99 seconds. (3) ALA ...

  • EverFocus EDR-1610A - page 37

    EDR910_1610_ma_en_rev1 00 - 37 - 3.7 NETWORK MENU Define all network-related settings in this menu. These settings should on ly be carried out by skilled personn el qu alified for network installation; if the DVR is implemented in existing networks, th e n etwork administrator should be consulted. This chapter doesn‘t go into basic network techni ...

  • EverFocus EDR-1610A - page 38

    EDR910_1610_ma_en_rev1 00 - 38 - (6) MULTICAST: If the DVR is connected to a server system , which provide Multicast mode, settings for this mode can be done here. YES: Multicast mode ON NO: Multicast mode OFF IP - ADRESS : IP-adress of Multicast server PORT : Port of Multicast - serv er (7) HTTP PORT: Default setting for thi s port is: 80. Th e po ...

  • EverFocus EDR-1610A - page 39

    EDR910_1610_ma_en_rev1 00 - 39 - (1) PROTOCOL: Network alarm transmi ssion protocol type TCP: TCP protocol transmission UDP: UDP protocol transmission (2) PORT : Network port through which the al arm is transmitted. This port must be set at the cli ent’s side (recipiant) correspondingly. (3) UNIQUE ID: DVR ID number, used for identification by t ...

  • EverFocus EDR-1610A - page 40

    EDR910_1610_ma_en_rev1 00 - 40 - 3.7.3 EMAIL (Email alarm) Define the recipiant’s e mail account settings for email alar m in the EMAIL menu item. Email alarms can be sent upon motion, al arm contact and technical alarms (WARNING menu). An *.arv file format alarm image is transm itted upon motion and alarm contact alarms. The visibility of these ...

  • EverFocus EDR-1610A - page 41

    EDR910_1610_ma_en_rev1 00 - 41 - Define user names, passwords and user rights for network access in the PASSWORD menu item. Up to 6 diff erent users can be defined: (1) NAME: User name for network login (2) PASSWOR D: Password fo r network login (3) LEVEL: Define the administrative ri ghts fo r network access. LIVE: only live view is possi ble, no ...

  • EverFocus EDR-1610A - page 42

    EDR910_1610_ma_en_rev1 00 - 42 - 3.7.6 DDNS The domain name system (DN S ) is the technology u s ed that allows an Internet domain name to be translated into an Internet Protocol addresses. A domain name is a meaningful and easy-to-remember na me for an Internet address. In DSL internet connect ions DSL provi der normally assign dynamic IP-adresses ...

  • EverFocus EDR-1610A - page 43

    EDR910_1610_ma_en_rev1 00 - 43 - 3.8 TIMER MENU Define the time frames for schedul ed recording in the TIMER menu: (1) DAY: MO (Monda y), TU (Tuesday), WE (Wednesday), TH (Thursday), FR (Friday), SA (Saturday), SU (Sunday) . WDAY: Monday to Friday. WEND: Weekend, Sa turday and Sunday. DLY: Daily. (2) START: Recording start time (3) END: Recording e ...

  • EverFocus EDR-1610A - page 44

    EDR910_1610_ma_en_rev1 00 - 44 - 3.9 DISK - HDD ( harddisk) MENU Check harddisk status and delete ha rddisk indexes in the HDD menu. (1) DISK VIDEO DELETE: After confirmation with SEL ECT and a further security request, the ha rddisk’s index i s deleted. Only Disk 1 is available for EDR910/1610. ATTENTION: Deleting the index d oes not comprise th ...

  • EverFocus EDR-1610A - page 45

    EDR910_1610_ma_en_rev1 00 - 45 - 3.10 RS232/RS485 MENU Define the settings for DVR remote cont rol through serial interface in the RS232/RS 485 menu. Pin assignment a nd remote control prot ocol are described in appendix B and C . (1) RS232 BAUD RAT E: RS-232 interface transmission speed. 1200, 2400, 4800, 9600, 19200 and 3840 baud ca n be selected ...

  • EverFocus EDR-1610A - page 46

    EDR910_1610_ma_en_rev1 00 - 46 - 3.11 WARNING MENU The EDR provides warnin g f unctions allowing signall ing upon operation failu re. Define the alarm reactions in the WARNING menu. 3.11.1 FAN FAIL URE Both fans provide fai lure detection. Define the alarm reactions upon fan failure in th is menu item: (1) BUZZER: By selection “ENABLE” , the bu ...

  • EverFocus EDR-1610A - page 47

    EDR910_1610_ma_en_rev1 00 - 47 - 3.11.2 HDD TEMP. The enduring HDD temperature surveillance gu arantees an alarm reaction in case the threshold value is exceeded. There may be several reasons for HDD temperature exce ss: • Exceedance of the max. tolerable am bient temperature (40°C), e.g. upon installation i n an electrical cabinet w it h inadeq ...

  • EverFocus EDR-1610A - page 48

    EDR910_1610_ma_en_rev1 00 - 48 - 3.11.3 NO HDD The DVR detects when both harddisks are remo ved, switched off or not detected. Define the alarm reactions in this menu item: (1) BUZZER: By selecting “ENABLE ”, the buzzer is activated. (2) ALARM OUTPUT: Output relay activation. 1 Output relay 1 sw itches upon alarm. NONE no output r elay reaction ...

  • EverFocus EDR-1610A - page 49

    EDR910_1610_ma_en_rev1 00 - 49 - 3.11.4 HDD FULL In operation mode HDD FULL: STOP (setting i n RECORDING menu), the recordi ng process is stopped if the harddisk is full. D efine the alarm reactions in th is menu item: (1) BUZZER: By selecting “ENABLE”, th e buzzer is activated. (2) ALARM OUTPUT: Output relay activation. 1 Output relay switches ...

  • EverFocus EDR-1610A - page 50

    EDR910_1610_ma_en_rev1 00 - 50 - 3.12 SYSTEM MENU Define the following setti ngs in the SYSTEM me nu: (1) SYSTEM VE RSION: Display of the installed f irmw a re v ersion. (2) SYSTEM VIDEO FO RM AT: Display of the detected video system PAL. The EDR automaticall y detects the video system upon system startup. (3) SAVE/LOAD CON FIGU RATI ON: Selecting ...

  • EverFocus EDR-1610A - page 51

    EDR910_1610_ma_en_rev1 00 - 51 - (5) LANGUAGE: System language selection. (6) QUICK PLAY: The "QuickPlay" fu nction is a co nvenient playb ack function all owing the immediate playback of video recorded 5~60 minut es ag o by pressing the PLAY key. ON: QuickPlay function activated. OFF: QuickPlay f unction deactivated. Pressing the PLAY ke ...

  • EverFocus EDR-1610A - page 52

    EDR910_1610_ma_en_rev1 00 - 52 - RECORDING 4. RECORDING 4.1 RECORDING ATTENTION: The followi ng instructions as regard t o the EDR DVR recor ding and recording standby have to be followe d thorough fully. Some of the DVR’s functions significant ly differ from pre vious models. Actuate the REC key to switch the DVR to recording resp. recording sta ...

  • EverFocus EDR-1610A - page 53

    EDR910_1610_ma_en_rev1 00 - 53 - 4.3 Event recording If event-triggered recordings are programme d in the ALAR M and/or MOTION menu, the respective cameras are recorded at the “EVE NT” recording rate (programming in CAMERA menu). ATTENTION: For this recording mode, the DVR must be in recording standby mode (REC-LED ON). The DVR can be switched ...

  • EverFocus EDR-1610A - page 54

    EDR910_1610_ma_en_rev1 00 - 54 - PLAYBACK 5. PLAYBACK 5.1 PLAYBACK WITHOUT SE ARCH FUNCTION (1) Playback Press the PLAY key to switch the DVR to pl ayback mode. Depending on the “QuickPlay” function settings (see SYSTEM me nu), playback starts at one of the followi ng positions: QuickPlay OFF : playback starts at the last playback position Quic ...

  • EverFocus EDR-1610A - page 55

    EDR910_1610_ma_en_rev1 00 - 55 - (4) Slow forward playback PA U SE PA U SE Press the PAUSE key during playback to freeze th e image at the cu rrent playback position. Turn the SHUTTLE clockwise for sl ow forward playba ck. Depending on the shuttle speed, the playback speed is reduced to 1 /2, 1/4, 1/8, 1/10 , 1/16, 1/32 of the normal speed. This pl ...

  • EverFocus EDR-1610A - page 56

    EDR910_1610_ma_en_rev1 00 - 56 - 5.2 PLAYBACK SEAR CH SEARCH SEARCH Press the SEARCH key to enter the search menu. NAVIGATION: Use the JOG to select values or entries. Use the ENTER key to go to t he next menu item and the DISPL AY key to go to the previous menu item. Press the SELECT key to confirm a selection. Press the MENU key to leave the sear ...

  • EverFocus EDR-1610A - page 57

    EDR910_1610_ma_en_rev1 00 - 57 - (2) EVENT SEARCH Enter EVENT in the first row o f the search menu i f you se arch for specific events such as alarm, motion detection or video loss. Preselect the type of ev ent to be l isted in the EVENT row. The followi ng types of event are available: Display Description ALARM Alarm events (alarm contacts and sys ...

  • EverFocus EDR-1610A - page 58

    EDR910_1610_ma_en_rev1 00 - 58 - COPY COPY VIDEO EXPORT 6. VIDEO EXPORT Video data can be exported as *.arv format m ovie file to both a USB stick or the external USB DVD drive EPR200. PC playback requires the dedicated viewer software which may be copied to USB stick through the COPY menu described below or which can be downloaded via the browser ...

  • EverFocus EDR-1610A - page 59

    EDR910_1610_ma_en_rev1 00 - 59 - DEVICE : USB / DVD Selecti on of export medium USB: Export to USB - Stick or external DVD-RW drive (EPR200) D VD: Export to in ternal DVD - driv e ( - D models only) ATTENTION: Use UDF f o rmat ted DVD+RW only for in ternal DVD drive. For deta il led information about formatti ng DVD+RW refer to Appendix D: FORMATTI ...

  • EverFocus EDR-1610A - page 60

    EDR910_1610_ma_en_rev1 00 - 60 - CALL MONITOR SETUP 7. CALL MONITOR SETUP Enter the call and matrix monitor setup menu by pressi ng the CALL key: Define the following setti ngs in the CALL menu: Press ENTER to select the respective moni tor and the selection options: (1) SEQ: “ON" activates the monitor’s sequence mode (automatic sequential ...

  • EverFocus EDR-1610A - page 61

    EDR910_1610_ma_en_rev1 00 - 61 - DISPLAY SETTINGS 8. DISPLAY SETTINGS 8.1. BRIGHTNESS, CONTRAST, COLO UR Press SELECT to adjust brightness, contrast and colour for each video channel in f ull screen mode of the respective camera ( chann el keys 1 ~ 9 resp. 1 ~ 1 6) : Press ENTER to switch between the settings and use t he JOG to adjust the value s ...

  • EverFocus EDR-1610A - page 62

    EDR910_1610_ma_en_rev1 00 - 62 - SCREEN DISPLAY 9. SCREEN DISPLAY Press the MODE key to switch between 4x, 7x, 9 x, 10x, 13x, 16 x and PiP (Pi cture-in- Picture) main monitor display. 10x, 13x and 16x display are available for EDR1610 only. ...

  • EverFocus EDR-1610A - page 63

    EDR910_1610_ma_en_rev1 00 - 63 - EDA 966 INFRARED REMOTE CONTROL (OPTIONAL) 10. EDA 966 INFRARED REM OTE CONTROL (optional) The optional EDA966 IR remote controller al lows the EDR remote operation covering a maximum distance of 10m. Basically, the keys com ply with the EDR DVR front panel keys. Key assignment differing to EDR front panel : JOG : J ...

  • EverFocus EDR-1610A - page 64

    EDR910_1610_ma_en_rev1 00 - 64 - NETWORK ACCESS 11. NETWORK ACCESS WI TH INTERNET EXPLORER 11.1 PC SYSTEM REQ UIREMENTS: Operating system Windows XP SP2 / Windows 2000 SP6, DirectX 9.0c, Internet Explorer min. 6.x. ActiveX applications must be permitte d in the Internet Explorer settings. The loading and inst allation of ActiveX compon ents during ...

  • EverFocus EDR-1610A - page 65

    EDR910_1610_ma_en_rev1 00 - 65 - 11.3 ACCESS VIA INTERNE T EXPLORER Enter the DVR IP address in the Internet Explorer address line: Enter user name and password in the LOGIN screen. ...

  • EverFocus EDR-1610A - page 66

    EDR910_1610_ma_en_rev1 00 - 66 - 11.4 SCREEN ELEMENTS The illustration sh ows the screen user interface with the following icons and operat in g elements: 1. REVERSE PLAYB ACK 2. STOP: Stop playback mode and switc h to live mode. 3. PLAYBACK 4. SINGLE IMAGE FORW ARD: Switch to next image in PAUSE mode. 5. PAUSE: Stop playback, fre eze image. 6. SIN ...

  • EverFocus EDR-1610A - page 67

    EDR910_1610_ma_en_rev1 00 - 67 - 11.5 PLAYBACK SE ARCH Select search mode either by time/date or by event list. Event list search mode Select the types of event to be displayed: ALARM, MOTI ON (motion detection), VLOSS (video loss). Press UPDATE to start / refresh the event list. The load time depends on both the ev ent list size and the network sp ...

  • EverFocus EDR-1610A - page 68

    EDR910_1610_ma_en_rev1 00 - 68 - TIME / DATE SEARCH Selecting "Search by Time" op ens an entry mask for playba ck position date and time input. Click on to open the time/date input window: There are 3 methods to do search by time. 1. Press the button of M for cha nging Month to be searched, D for day, h for hour, m for minute and s for se ...

  • EverFocus EDR-1610A - page 69

    EDR910_1610_ma_en_rev1 00 - 69 - 11.6 PTZ CONTROL The EDR DVR allows the speed dome an d PTZ device control via networ k. Select “PTZ” to acti vate the telemetry mode. Select the camera in the PT Z CAM field. The following con trol functions are available: 1. PTZ Cam: camera selection 2. Action mode : Pan/tilt/zoom key reaction type Continuous ...

  • EverFocus EDR-1610A - page 70

    EDR910_1610_ma_en_rev1 00 - 70 - 5. Focus: manual focus NEAR : near range, FAR : tele range 6. IRIS: manual iris con trol OPEN : open iris CLOSE : close iris 7. CLICK TO PRESET POINT: Preset selection Numbers 1-5: go to preset 1 ~ 5 "Number" > GO: go to selected preset SET : Save current PTZ position as selected preset number CLR : Del ...

  • EverFocus EDR-1610A - page 71

    EDR910_1610_ma_en_rev1 00 - 71 - 11.7 REMOTE ARCHIVING This function allow s to export a video file of a single came ra in original *.arv - file format. For the playback of the exported file, the a pplication "DVRVi ewer" is required. To Archive files: 1. Select Disk No . (only Disk 1 is av ailab le for EDR910/1610) 2. Start Time/End Time ...

  • EverFocus EDR-1610A - page 72

    EDR910_1610_ma_en_rev1 00 - 72 - 3. Enter Month, Day, Hou r, Minute, and seco nd directly in display bar. Press OK to enter the settings. Press ARCHIVE butt on to start archivin g. An “ .arv” file will be saved. Press STOP button if you wish to cancel arch iv ing. 12. DVRViewer - PLAYBAC K OF *.arv - FILES EDR video data exporte d with the COPY ...

  • EverFocus EDR-1610A - page 73

    EDR910_1610_ma_en_rev1 00 - 73 - OPERATION DVR VIEWER Detailed explanat ion of DVRViewer is as follows: 1. Load File : to load the archived EDR MP E G Files (.arv). 2. Stop : to stop playing “.arv” file. 3. Play : to play “.arv” f ile. 4. <<Step : step backward of the playing file. 5. Pause : to pause playing. 6. Step>> : step f ...

  • EverFocus EDR-1610A - page 74

    EDR910_1610_ma_en_rev1 00 - 74 - APPENDIX A: Interface specification INTERF ACE SPECIF ICATIO N 1. RS-232 Pin assign ment The RS232 interface of EDR1610/910 is reserved for service purpose. Pin assignment 9-pi n RS-232 plug RS-485 pin assi gn ment Both RS-485 sockets are equally wired. Pin 1: GND Pin 3: RS485 + (A) Pin 6: RS485 - (B) Illustration: ...

  • EverFocus EDR-1610A - page 75

    EDR910_1610_ma_en_rev1 00 - 75 - APPENDIX B: Remote control protocol Remote control prot ocol The following remote control protocol appl ies to RS485 remote control. The EEPBus protocol is a universal contro l protocol for EDSR and EDR (MPEG4) seri es’ digital video recorders. Therefore, it may occur that some of the following commands are n ot a ...

  • EverFocus EDR-1610A - page 76

    EDR910_1610_ma_en_rev1 00 - 76 - 2-3. Receiver ID 1.) Individual receiver ID Decimal 14bit binary value Hbyt e Lb yte Receiv er ID (EDSR) 0 0000000 0000000 00 00 ID = 0 1 0000000 0000001 00 01 ID = 1 2 0000000 0000010 00 02 ID = 2 .... 126 0000000 1111110 00 7e ID = 126 127 0000000 1111111 00 7f ID = 127 128 0000001 0000000 01 00 ID = 128 129 00000 ...

  • EverFocus EDR-1610A - page 77

    EDR910_1610_ma_en_rev1 00 - 77 - 2-4. Opcode Byte & Data bytes 2-4-1. OPcode OPcode Data1 Function 0x4B Keycode A remote key pressed 0x4D command Matrix command 2-4-2. Remote ke ys (OPcode=0x4B) ----------------- ------------- ---------------- ---------------- ---------------- ---- Data1 Key Data1 Key 0x00 CH1 0x1e JOG< 0x01 CH2 0x1f JOG> ...

  • EverFocus EDR-1610A - page 78

    EDR910_1610_ma_en_rev1 00 - 78 - 2-4-3. Matrix command (OPcode=0x4D) 2-5. Checksum Byte Checksum is computed as the sum of all previo us by tes (including th e length byte), t hen mask with 0x7f. Data1 Matrix function 0x00 Matrix monitor0 - ch01 spot 0x01 Matrix monitor0 - ch02 spot 0x02 Matrix monitor0 - ch03 spot 0x03 Matrix monitor0 - ch04 spot ...

  • EverFocus EDR-1610A - page 79

    EDR910_1610_ma_en_rev1 00 - 79 - APPENDIX C: Recording times Average recording times, based on 100GB harddisk capacity. Using the VBR (Varia ble Bit Rate) method, the storage requirement per image depends on the image’s colour and contrast content and captured motion. The following calcu latio ns represent sample values for contin uous recording. ...

  • EverFocus EDR-1610A - page 80

    EDR910_1610_ma_en_rev1 00 - 80 - APPENDIX D: NERO InCD Formatting For video export to DVD+RW me dia, formatting the media to UDF format is mandatory. The package of the recorder co ntains the b urning software NERO. A part of the program package is the application InCD. InCD allows to format DVD +RW medias to UDF format. For installation of InCD re ...

  • EverFocus EDR-1610A - page 81

    EDR910_1610_ma_en_rev1 00 - 81 - Please insert DVD-RW t o DVD burner, open My Computer window, ri ght-click on DVD burner, then choose InCD Format. From the following setu p window, please choose “ Advanced ” to do more advanced setting. ...

  • EverFocus EDR-1610A - page 82

    EDR910_1610_ma_en_rev1 00 - 82 - Choose “ UDF 1.50 ” in the following w indow and click OK to return to the format setti ng window. Please choose “Format” option as follows. Information from CD may not be written in or recognized for the reason that Quick format is selected. Check “ Ve rify ” in Other options to verify if the re’s an ...

  • EverFocus EDR-1610A - page 83

    EDR910_1610_ma_en_rev1 00 - 83 - EverFocus Electronics Corp. Headoffice: 12F, No.79 Sec. 1 Shin-Tai Wu Ro ad, Hsi-Chih, Taipei, Taiwan www.everfocus.com.tw USA Office : 1801 Highland Ave. Unit A Duarte, CA 91010, U.S.A. www.everfocus.com European Office: Albert-Einstein-Straße 1 D-46446 Emmerich, Germany www.everfocus.de China Office: Room 609, Te ...

Manufacturer EverFocus Category DVR

Documents that we receive from a manufacturer of a EverFocus EDR-1610A can be divided into several groups. They are, among others:
- EverFocus technical drawings
- EDR-1610A manuals
- EverFocus product data sheets
- information booklets
- or energy labels EverFocus EDR-1610A
All of them are important, but the most important information from the point of view of use of the device are in the user manual EverFocus EDR-1610A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals EverFocus EDR-1610A, service manual, brief instructions and user manuals EverFocus EDR-1610A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product EverFocus EDR-1610A.

Similar manuals

A complete manual for the device EverFocus EDR-1610A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use EverFocus EDR-1610A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of EverFocus EDR-1610A.

A complete EverFocus manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual EverFocus EDR-1610A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the EverFocus EDR-1610A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the EverFocus EDR-1610A, that we can find in the current document
3. Tips how to use the basic functions of the device EverFocus EDR-1610A - which should help us in our first steps of using EverFocus EDR-1610A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with EverFocus EDR-1610A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of EverFocus EDR-1610A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning EverFocus EDR-1610A?

Use the form below

If you did not solve your problem by using a manual EverFocus EDR-1610A, ask a question using the form below. If a user had a similar problem with EverFocus EDR-1610A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)