English dropdown-ico

Manual Kenmore POWER MISER 153.33062

32 pages 3.61 mb
Download

Go to site of 32

Summary
  • Kenmore POWER MISER 153.33062 - page 1

    Owner's Manual POWER MISERTM 6 ULTRA LOW NOx GAS WATER HEATER FOR POTABLE WATER HEATING ONLY. NOT SUITABLE FOR SPACE HEATING. NOT FOR USE IN MOBILE HOMES. MODEL NO. 153.330632 30 Gallon 153.330642 40 Gallon 153.330620 40 Gallon (Short) 153.330652 50 Gallon This water heater meets the new ANSI Z21.10.1 standard that deals with the accidental or ...

  • Kenmore POWER MISER 153.33062 - page 2

    Your safety and the safety of others is extremely important in the installation, use and servicing of this water heater. Many safety-related messages and instructions have been provided in this manual and on your own water heater to warn you and others of a potential hazard. Read and obey all safety messages and instructions throughout this manual. ...

  • Kenmore POWER MISER 153.33062 - page 3

    Fire Hazard Read and understand instruction manual and safety messages For continued protection against before installing, operating or riskof fire: servicing this water heater. Failure to follow instructions and • Do not install water heater on safety messages could result in carpeted floor. death or serious injury. • Do not operate water heat ...

  • Kenmore POWER MISER 153.33062 - page 4

    SAFE INSTALLATION, USE AND SERVICE ...................................................................................................................... 2 SAFETY PRECAUTIONS .............................................................................................................................. 3 TABLE OF CONTENTS ............................ ...

  • Kenmore POWER MISER 153.33062 - page 5

    Thank You for purchasing a Kenmore water heater. Properly installed and maintained, it should give you years of trouble free service. If you should decide that you want the new water heater professionally installed by Sears, call 1-800-4-MY-HOME ®. They will arrange for prompt, quality installation by Sears authorized contractors. Abbreviations Fo ...

  • Kenmore POWER MISER 153.33062 - page 6

    Materials Needed To simplify the installation, Sears has available the installation parts shown below. You may or may not need all of these materials, depending on your type of installation. EXPANSION TANKS FOR THERMAL EXPANSION CONDITIONS AVAILABLE IN 2 GALLONS (7.6 LITERS) AND 5 GALLONS (18.9 LITERS) CAPACITY THROUGH LOCAL SEARS STORE OR SERVICE ...

  • Kenmore POWER MISER 153.33062 - page 7

    GET TO KNOW YOUR WATER HEATER - GAS MODELS A Vent Pipe B Drafthood C Anode D Hot Water Outlet E Outlet F Flexible Water Connections G Gas Supply H Manual Gas Shut-off Valve I Ground Joint Union J Drip Leg (Sediment Trap) K Inner Door L Outer door M Union N Inlet Water Shut-off Valve O Cold Water Inlet P Inlet Dip Tube Q Temperature-Pressure Relief ...

  • Kenmore POWER MISER 153.33062 - page 8

    Removing the Old Water Heater ® G FIGURE 2. QTurn "OFF" the gas supply to the water heater. If the main gas line shutoff valve serving all gas appliances is used, also shut "OFF" the gas at each appliance. Leave all gas appliances shut "OFF" until the water heater installation is completed, see Figures 2 and 3. FIGURE ...

  • Kenmore POWER MISER 153.33062 - page 9

    Facts to Consider About the Location Carefully choose an indoor location for the new water heater. The placement is a very important consideration for the safety of the occupants in the building and for the most economical use of the appliance. This water heater is not for use in manufactured (mobile) homes or outdoor installation. Whether replacin ...

  • Kenmore POWER MISER 153.33062 - page 10

    Fire or Explosion Hazard Read instruction manual before installing, using or servicing water heater. • Improper use may result in fire or explosion. • Maintain required clearances to combustibles. Minimum clearances between the water heater and combustible surfaces are 0 inch at the sides and rear, 4 inches (102 mm) at the front, and 6 inches ( ...

  • Kenmore POWER MISER 153.33062 - page 11

    • Do obtain new warning and instruction labels from Sears for placement on the blanket directly over the existing labels. • Do inspect the insulation blanket frequently to make certain it does not sag, thereby obstructing combustion air flow. Combustion Air and Ventilation for Appliances Located in Unconfined Spaces UNCONFINED SPACE is space wh ...

  • Kenmore POWER MISER 153.33062 - page 12

    GAS VENT INLET AIR DUCT FIGURE 13. Alternatively a single permanent opening may be used when communicating directly with the outdoors, or with spaces that freely communicate with the outdoors. The opening shall have a minimum free area of 1 square inch per 3,000 BTU per hour (8.3 cm2/kW) of total input rating of all equipment in the enclosure. See ...

  • Kenmore POWER MISER 153.33062 - page 13

    This water heater shall not be connected to any heating systems or component(s) used with a non-potable water heating appliance. All piping components connected to this unit for space heating applications shall be suitable for use with potable water. Toxic chemicals, such as those used for boiler treatment shall not be introduced into this system. ...

  • Kenmore POWER MISER 153.33062 - page 14

    Fit T & P valve insulation over valve. Make sure that the insulation does not interfere with the lever of the T & P valve. Secure all insulation using tape. Temperature-Pressure Relief Valve Explosion Hazard • Temperature-pressure relief valve must comply with ANSI Z21.22 and ASME code. • Properly sized temperature- pressure relief valv ...

  • Kenmore POWER MISER 153.33062 - page 15

    The temperature-pressure relief valve must be manually operated at least once a year. Caution should be taken to ensure that (1) no one is in front of or around the outlet of the temperature- pressure relief valve discharge line, and (2) the water manually discharged wilt not cause any bodily injury or property damage because the water may be extre ...

  • Kenmore POWER MISER 153.33062 - page 16

    SHEET METAL SCR&WS (_O_t _e/_4d_} tNSIALL THE ORAFT HOOD WITH THE FOUR SCREWS PROVIDED. FIGURE 17. The vent pipe from the water heater must be no tess than the diameter of the draft hood outlet on the water heater and must slope upward at least 1/4 inch per linear foot (21 mm per meter). See Figure 18. TO CHIMNEY t FIGURE 18. All vent gases mus ...

  • Kenmore POWER MISER 153.33062 - page 17

    Breathing Hazard - Carbon Monoxide Gas • High attiC:uric or;rice must _ nstalled for epera_on above 2,000 feet (610 m), • Ceatact a qualified installer or service agency Breathing car_n monoxide eaa cause brain damage o[ d_ath Always read and understand instruction rna_ual Water heaters covered in this manual have been tested and approved for i ...

  • Kenmore POWER MISER 153.33062 - page 18

    A, B_ FOR YOUR SAFETY READ BEFORE LIGHTING I WARNING: Ifyou donot followthe_ instruc_ns exa_ly, a fire or explosion J ! = may resuff causing property damage, personal injury or IDes of life. I _ This a_liance has a pi_t which is lighted _ a C, Use only your hand to push inor turn _e gas control _ezoelectfic _n_r_ Men iighting the pilot, foliowthese ...

  • Kenmore POWER MISER 153.33062 - page 19

    Temperature Regulation Due to the nature of the typical gas water heater, the water temperature in certain situations may vary up to 30F ° (16.7 C °) higher or lower at the point of use such as, bathtubs, showers, sink, etc. o7:1[el ;t Water temperature over 125°F (52°C) can cause severe burns instantly resulting in severe injury ordeath. Child ...

  • Kenmore POWER MISER 153.33062 - page 20

    Tank (Sediment) Cleaning Burner Inspection Sediment build-up on the tank bottom may create varying amount of noise and if left in the tank will cause permanent tank failure. In some water areas, you may not be able to drain all sediment deposits by simply draining the tank. In these cases Mag-Erad (part no. 23600) can be used to help remove the sed ...

  • Kenmore POWER MISER 153.33062 - page 21

    Removing the Burner Door Assembly 1, 2. 3, 4. Turn off the gas to the water heater at the manual gas shut-off valve (Figure 3). Turn the gas control knob on the combination gas control valve/thermostat clockwise to the "OFF" position (Figure 1 ). NOTE: Depress the dial stop on Robertshaw valve before turning the gas control knob. See Ligh ...

  • Kenmore POWER MISER 153.33062 - page 22

    Replacing the Thermocouple 1. Remove the Burner Door Assembly as directed previously. 2. Remove the retainer clip from the back of the two piece wire connector and remove the two piece wire connector from the assembly (Figure 27). 3. Pull the thermocoupte from the pilot assembly (Figure 31 ). IMPORTANT: Be careful not to bend or alter the position ...

  • Kenmore POWER MISER 153.33062 - page 23

    Replacing the Burner Door Assembly Fire or Explosion Hazard * Tighten _th manifold door screws securely., - Remove any fibe_Iass between gasket and combustion chamber. ,Repiace viewport if giass is missing or damaged, * Replace two piece wire _nnector if missing or removed, , Rep_a_ door gasket if damaged, - FaJiure to foiiow these _nstructJons _ r ...

  • Kenmore POWER MISER 153.33062 - page 24

    Removing and Replacing the Gas Control Valve/Thermostat IMPORTANT: The gas control valve/thermostat is a standard valve with a right-hand thread thermocouple. Use only factory authorized replacement parts. Removing the Gas Control Valve/Thermostat: 1. Turn the gas control knob on the combination gas control valve/thermostat clockwise to the "O ...

  • Kenmore POWER MISER 153.33062 - page 25

    or replaced more often than an anode rod that appears to be intact. Replacement of a depleted anode rod can extend the life of your water heater. Inspection should be conducted by calling the Sears Service Center for an authorized contractor. At a minimum, the anode(s) should be checked annually after the warranty period. Temperature-Pressure Relie ...

  • Kenmore POWER MISER 153.33062 - page 26

    Start Up Conditions Thermal Expansion Property Damage Hazard • Avoid water heater damage. • Install thermal expansion tank or device if necessary. • Contact qualified installer or service agency. As water is heated, it expands (thermal expansion). In a closed system, the volume of water wilt grow. As the volume of water grows, there wilt be a ...

  • Kenmore POWER MISER 153.33062 - page 27

    Condensation Whenever the water heater is filled with cold water, some condensate will form while the burner is on. A water heater may appear to be leaking when in fact the water is condensation. This usually happens when: • A new water heater is filled with cold water for the first time. • Burning gas produces water vapor In water heaters, par ...

  • Kenmore POWER MISER 153.33062 - page 28

    PROBLEM BURNER WILL NOT IGNITE POSSIBLE CAUSE(S) 1. Pilot not tit 2. Thermostat set too low 3. No gas 4. Dirt in the gas lines 5. Pilot tine clogged 6. Main burner line clogged 7. Non-functioning thermocouple 8. Non-functioning thermostat 9. Heater installed in a confined area CORRECTIVE ACTION 1. Light pilot 2. Turn temp. dial to desired temperatu ...

  • Kenmore POWER MISER 153.33062 - page 29

    PROBLEM POSSIBLE CAUSE(S) CORRECTIVE ACTION DRIP FROM RELIEF VALVE 1. Excessive water pressure 1. Use a pressure reducing valve and relief valve 2. Closed water system 2. See "Thermal Expansion" THERMOSTAT FAILS TO 1. Non-functioning thermostat 1. Replace thermostat SHUT OFF 2. Improper calibration 2. Replace thermostat COMBUSTION ODORS 1 ...

  • Kenmore POWER MISER 153.33062 - page 30

    Section A: Pilot light will not light. • ICheck the manual gas shut-oft valve to I Dis the gas turned on? I_NO mplsee if it is in the open position, if it is open I YES " Ithen contact the gas utility company. I While repeatedly depressing the igniter button, Have you bled all the air | •l hold down the reset button until the pilot is lit ...

  • Kenmore POWER MISER 153.33062 - page 31

    POWER MISER TM 6 GAS WATER HEATER 153.330632 30 Gallon 153.330642 40 Gallon 153.330620 40 Gallon (Short) 153.330652 50 Gallon Alternate anode location for tc T&P Anode location for side -.@ Model Numbers Key No. Part Description 153.330632 153.330642 153.330620 153.330652 1 Draft Hood 185917-001 185917-001 185917-001 185917-001 2 Heat Trap (Col ...

  • Kenmore POWER MISER 153.33062 - page 32

    6 - YEAR LIMITED WARRANTY ON WATER HEATER For six years from the date of purchase, if this water heater is installed and operated in a single-family home in accordance with the owner's manual instructions and all local applicable plumbing codes, Sears will: Supply free water heater parts for those that are defective in material or workmanship. ...

Manufacturer Kenmore Category Water Heater

Documents that we receive from a manufacturer of a Kenmore POWER MISER 153.33062 can be divided into several groups. They are, among others:
- Kenmore technical drawings
- POWER MISER 153.33062 manuals
- Kenmore product data sheets
- information booklets
- or energy labels Kenmore POWER MISER 153.33062
All of them are important, but the most important information from the point of view of use of the device are in the user manual Kenmore POWER MISER 153.33062.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Kenmore POWER MISER 153.33062, service manual, brief instructions and user manuals Kenmore POWER MISER 153.33062. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Kenmore POWER MISER 153.33062.

Similar manuals

A complete manual for the device Kenmore POWER MISER 153.33062, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Kenmore POWER MISER 153.33062 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Kenmore POWER MISER 153.33062.

A complete Kenmore manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Kenmore POWER MISER 153.33062 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Kenmore POWER MISER 153.33062, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Kenmore POWER MISER 153.33062, that we can find in the current document
3. Tips how to use the basic functions of the device Kenmore POWER MISER 153.33062 - which should help us in our first steps of using Kenmore POWER MISER 153.33062
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Kenmore POWER MISER 153.33062
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Kenmore POWER MISER 153.33062 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Kenmore POWER MISER 153.33062?

Use the form below

If you did not solve your problem by using a manual Kenmore POWER MISER 153.33062, ask a question using the form below. If a user had a similar problem with Kenmore POWER MISER 153.33062 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)