English dropdown-ico

Manual Fusion L50B PRO

16 pages 0.82 mb
Download

Go to site of 16

Summary
  • Fusion L50B PRO - page 1

    Thank you for purchasing this T yphoon L50B Pro charger . W e are sure you will be pleased with its per formance and features . In order to ensure that you obtain the maximum benefit from its operation, please read these instructions carefully . TYPHOON L50B Pro opErA ting instructions Please keep for future reference ...

  • Fusion L50B PRO - page 2

    ...

  • Fusion L50B PRO - page 3

    1 Input V oltage 11~15V DC Battery T ype & Cells 1~5 Lithium-Ion or Lithium-Polymer cells (3.6V or 3.7V respectively) 1~6 LiFePO4 cells (3.3V) 1~14 Nickel-Cadmium cells 1~14 Nickel-Metal Hydride cells 1 - 6 Lead-Acid cells (2V per cell) Battery Capacity 100mAh ~ 6000mAh adjustable ONL Y for Lithium-Ion, Lithium-Polymer and LiFePO4 Charge Rate 0 ...

  • Fusion L50B PRO - page 4

    2 SAFEty prE cA utions • DO NOT attempt to charge incompatible types of rechargeable batteries. This charger is designed to only charge and discharge Nickel-Cadmium, Nickel-Metal Hydride, Lithium-Ion, Lithium-Polymer , LiFePO4 and Lead- Acid batteries. • Make sure you place the charger on a firm level surface ...

  • Fusion L50B PRO - page 5

    3 Lithium Ion/pol ymEr BA ttEry SAFEty W Arnings Ensure that the charger and battery are placed on a non-flammable surface whilst charging and ideally charge outdoors wherever possible. NEVER charge a Lithium ION/Polymer/F e battery inside a vehicle whatever the circumstances. ALWAYS ensure that the charger is correctly set for the battery being ch ...

  • Fusion L50B PRO - page 6

    4 Lithium Ion/pol ymEr/FE BA ttEriEs Lithium battery packs must NEVER be discharged below 3 volts per cell as this will result in damage to the cells. If the voltage is allowed to drop below 3 volts per cell the battery voltage may seem to recover following a charge, but the battery may not then give its full nominal capacity and a reduction in per ...

  • Fusion L50B PRO - page 7

    5 Input powEr 12V DC Connect the charger’s red alligator clip to the positive (+) terminal on the power source and the black alligator clip to the negative (-) terminal. The charger will display “Input voltage” error message if the input is below 11V or above 15V . If this happens, please recheck the input power supply to make sure correct po ...

  • Fusion L50B PRO - page 8

    6 NiCd CHARGE C=3.0A BA TT TYPE NiCd CHARGE C=3.0A ST ART BA TTERY CHECK W AIT PLEASE.... CHG 0:00 00000 NC+3.00A 5.200V INC DEC ENTER INC DEC NiCd delta-peak- volt = 0mV/cell NiCd delta-peak- volt = 0mV/cell ENTER INC DEC Setting Charge Current Adjust the desired charge current, which ranges from 0.1A to 6.0A with the INC & DEC buttons. Press ...

  • Fusion L50B PRO - page 9

    7 NiMH CHARGE C=3.0A BA TT TYPE NiMH CHARGE C=3.0A ST ART BA TTERY CHECK W AIT PLEASE.... CHG 0:00 00000 NC+3.00A 5.200V INC DEC ENTER INC DEC NiMH delta-peak- volt = 0mV/cell NiMH delta-peak- volt = 0mV/cell ENTER INC DEC Setting Charge Current Adjust the desired charge current, which ranges from 0.1A to 6.0A with the INC & DEC buttons. Press ...

  • Fusion L50B PRO - page 10

    8 Lilo CHARGE 3.0A C=3000mAh 10.8Vp INC BA TT TYPE DEC ENTER Lilo CHARGE 3.0A C=3000mAh 10.8Vp INC DEC ST ART BA TTERY CHECK W AIT PLEASE.... CHG 0:00 00000 LI + 3.00A 12.000V Lilo CHARGE 3.0A C=3000mAh 10.8Vp INC DEC Lilo CHARGE 3.0A C=3000mAh 10.8Vp INC DEC BALANCER CON. NOT C ONNEC TED BALANCER CON. CONNECTED Lithium Type Lilo ENTER Lithium Type ...

  • Fusion L50B PRO - page 11

    9 Setting Charge Current Always set the capacity first. When the capacity has been set, the current will automaticallyshow an equivalent of 1C. Forinstance, a 3000mAh battery will initially show 3A. This can be varied up to 2C (6A max) or down to 0.1A using the INC & DEC buttons. That current may be further limited ...

  • Fusion L50B PRO - page 12

    10 PB CHARGE C=3.0A 12Vpack BA TT TYPE ENTER PB CHARGE C=3.0A 12Vpack INC DEC ST ART BA TTERY CHECK W AIT PLEASE.... CHG 0:00 00000 PB + 3.0 A 12.000V PB CHARGE C=3.0A 12Vpack INC DEC to NiCd charge ENTER Setting Charge Current Adjust the desired charge current, which ranges from 0.1A to 6.0A with the INC & DEC buttons. Press the ENTER button t ...

  • Fusion L50B PRO - page 13

    11 Displays During Charge ScrE En DisplA ys CHG 0.30:25 00000 NC + 3.00A 5.200V “BL C ” will be shown if the balancer cable of the battery is connec ted to the balancing port of the charger . CHG: Charge NC = NiCd NM = NiMH Ll = Lilo, LP = LiP o, LF = LiF e Pb = Pb If the Enter button is pressed at any stage, the charge can be terminated. END 0 ...

  • Fusion L50B PRO - page 14

    12 INPUT BA TTERY VOL T AGE ERROR Error mEs sA gEs NO BA TTERY OUTPUT BA TTERY REVERSE POLARIT Y OUTPUT CIRCUIT PROBLEM CHECK THE BA T T . OPEN CIRCUIT CHECK THE BA T T . OVER VOL T AGE CHECK THE BA T T . L OW VOL T AGE BALANCER VOL T AGE IS TOO HIGH BALANCER VOL T AGE IS TOO L OW DON’T CHAR GE LiXX WITH THIS MODE Input voltage is below 11.0V or ...

  • Fusion L50B PRO - page 15

    ...

  • Fusion L50B PRO - page 16

    Logic RC Limited 14 Hartham Lane Herford SG14 1QN United Kingdom www. L ogic rC .com ...

Manufacturer Fusion Category Battery Charger

Documents that we receive from a manufacturer of a Fusion L50B PRO can be divided into several groups. They are, among others:
- Fusion technical drawings
- L50B PRO manuals
- Fusion product data sheets
- information booklets
- or energy labels Fusion L50B PRO
All of them are important, but the most important information from the point of view of use of the device are in the user manual Fusion L50B PRO.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Fusion L50B PRO, service manual, brief instructions and user manuals Fusion L50B PRO. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Fusion L50B PRO.

Similar manuals

A complete manual for the device Fusion L50B PRO, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Fusion L50B PRO by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Fusion L50B PRO.

A complete Fusion manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Fusion L50B PRO - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Fusion L50B PRO, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Fusion L50B PRO, that we can find in the current document
3. Tips how to use the basic functions of the device Fusion L50B PRO - which should help us in our first steps of using Fusion L50B PRO
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Fusion L50B PRO
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Fusion L50B PRO in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Fusion L50B PRO?

Use the form below

If you did not solve your problem by using a manual Fusion L50B PRO, ask a question using the form below. If a user had a similar problem with Fusion L50B PRO it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)