English dropdown-ico

Manual Intel ECB-862

114 pages 2.26 mb
Download

Go to site of 114

Summary
  • Intel ECB-862 - page 1

    Part No.2047862000 User’s Manual ECB-862 Series Intel Pentium III Full-size PICMG CPU Card with 4 USB 2.0, Audio, & Dual 10/100 Base-Tx Ethernet 3 rd Ed. – 20 May, 2005 ...

  • Intel ECB-862 - page 2

    ECB-862/862L Evalue Technology Inc. FCC STATEMENT THIS DEVICE COMPLIES WITH PART 15 F CC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE. (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. THIS EQUIPMENT HAS BEEN TESTED AND ...

  • Intel ECB-862 - page 3

    User’s Manual Evalue Technology Inc. Copyright Notice Copyright © 2003 - 2005, Evalue Technology Inc., ALL RIGHTS RESERVED. No part of this document may be reproduced, copi ed, translated, or tr ansmitted in any form or by any means, electronic or mechanical, for any purpose, without the prior written permission of the original manufacturer. Tra ...

  • Intel ECB-862 - page 4

    ECB-862/862L Evalue Technology Inc. A Message to the Customer Evalue Customer Services Each and every Evalue’s product is built to t he most exacting specifications to ensure reliable performance in the harsh and dem anding conditions typical of industrial environments. Whether your new Evalue device is destined for the laboratory or the factory ...

  • Intel ECB-862 - page 5

    User’s Manual Evalue Technology Inc. Product Warranty Evalue warrants to you, the original purchaser , that each of its pr oducts will be free from defects in materials and workmanship fo r two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair pers onnel ...

  • Intel ECB-862 - page 6

    ECB-862/862L Evalue Technology Inc. Packing List Before you begin installing your single boar d, please make sure that the following materials have been shipped:  1 ECB-862 Series Pentium III Full-size CPU card  1 Quick Installation Guide  1 CD-ROM contains the followings: — User’s Manual (this manual in PDF file) — Ethernet driver a ...

  • Intel ECB-862 - page 7

    User’s Manual Evalue Technology Inc. 1. MANUAL OBJECTIVES ............................................................................................. 1 2. INTRODUCTION ........................................................................................................ 2 2.1 System O verview .................................................. ...

  • Intel ECB-862 - page 8

    ECB-862/862L Evalue Technology Inc. 3.9.1 Audio / TV Output Connector (AUDIO1) ......................................................................23 3.9.2 CD-ROM Audio Input Connector (CD1) .......................................................................23 3.9.3 Primary IDE Connector (CN1) ................................................. ...

  • Intel ECB-862 - page 9

    User’s Manual Evalue Technology Inc. 4.5.10 Load Fail-Safe Defaults ................................................................................................66 4.5.11 Load Optimized Defaults ..............................................................................................67 4.5.12 Set Supervisor/User Password ................. ...

  • Intel ECB-862 - page 10

    ECB-862/862L Evalue Technology Inc. Memory Parity Error At... ...................................................................................................... .....95 Memory Size Has Changed Since Last Boot ............................................................................95 Memory Verify Error At... ................................ ...

  • Intel ECB-862 - page 11

    User’s Manual Evalue Technology Inc. Document Amendment History Revision Date By Comment 1 st October, 2003 Stephen Tsao Initial Release 2 nd March, 2004 Stephen Tsao Add in 3.9.27 LCD panel connector description (page 37) 3 rd May, 2005 Stephen Tsao 1. Modify CN19 USB pin definition 2. CN8’s signal updated. 3. Cn13’s signals modified from US ...

  • Intel ECB-862 - page 12

    ECB-862/862L ECB-862/862L User’s Manual 1 1. Manual Objectives This manual describes in detail the Evalue Technology ECB-862 Single Board. We have tried to include as much informa tion as possible but we have not duplicated information that is provided in the standard IBM Technical References, unless it proved to be necessary to aid in the unders ...

  • Intel ECB-862 - page 13

    User’s Manual 2 ECB-862/862L User’s Manual 2. Introduction 2.1 System Overview The ECB-862 is an all-in-one Fu ll-size Pentium III Single Board Computer (SBC) designed with Intel embedded chipset VIA 8602 which supports the latest Intel Pentium III CPU with FSB up to 133 MHz, dual PCI-bus Fast Et hernet controllers, and M-Systems DiskOnChip soc ...

  • Intel ECB-862 - page 14

    ECB-862/862L ECB-862/862L User’s Manual 3 2.2 System Specifications General Functions • CPU: Universal Socket 370 supports Intel FC-PGA/FC-PGA2 Pentium III / Celeron (CopperMine and Tualatin) and VIA C3 CPU with FSB up to 133MHz • CPU Socket: Intel FC-370, Socket 370 • BIOS: Award 2Mbit Flash BIOS • Chipset: VIA VT8602 / VT82C686B • I/O ...

  • Intel ECB-862 - page 15

    User’s Manual 4 ECB-862/862L User’s Manual Optional TV Output Interface TV Encoder: VIA VT1621 TV output interface: Supports both RCA jack and S terminal SSD Interface One 32-pin DIP socket supports M-Systems DiskOnChip 2000 series up to 1 G Bytes Compact Flash: One CF socket supports Type I / II Compact Flash Card Mechanical and Environmental ...

  • Intel ECB-862 - page 16

    ECB-862/862L ECB-862/862L User’s Manual 5 2.3 Architecture Overview The following block diagram shows the arch itecture and main components of ECB-862. The two key components on board are the VIA VT8602 North Bridge and VT82C686B super South Bridge. These two devices provi de the ISA and PCI bus to which all the major components are attached. The ...

  • Intel ECB-862 - page 17

    User’s Manual 6 ECB-862/862L User’s Manual 2.3.1 VIA VT8602 North Bridge The Apollo PLE133T Graphics Controller is a hi ghly integrated display control device that incorporates a 64-bit 3D/2D graphic engi ne and video accelerator with advanced DVD video and optional TV output c apability. It provides a flexible and high performance solution for ...

  • Intel ECB-862 - page 18

    ECB-862/862L ECB-862/862L User’s Manual 7 2.3.2 Advanced High-Performance DRAM Controller  DRAM interface synchronous or pseudosyn chronous with CPU FSB speed of 133 / 100 / 66 MHz  DRAM interface may be faster than CPU by 33 MHz to allow use of PC133 with 100 MHz VIA C3, Pentium III or Pentium III-M (T ualatin) CPUs or use of PC100 with 66 ...

  • Intel ECB-862 - page 19

    User’s Manual 8 ECB-862/862L User’s Manual  BIOS shadow at 16KB increment  Decoupled and burst DRAM refresh with staggered RAS timing  CAS before RAS or self refresh 2.3.3 VIA VT82C686B South Bridge The VT82C686B PSIPC (PCI Super-I/O Integr ated Peripheral Controller) is a high integration, high performance, power-efficien t, and high ...

  • Intel ECB-862 - page 20

    ECB-862/862L ECB-862/862L User’s Manual 9  Integrated PCI-mastering dual full-dupl ex direct-sound AC97-link-compatible sound system. Hardware soundblaster-pro and hardware-assisted FM blocks are included for Windows DOS box and real -mode DOS compatibility. Loopback capability is also implemented for direct ing mixed audio streams into USB an ...

  • Intel ECB-862 - page 21

    User’s Manual 10 ECB-862/862L User’s Manual  Supports L1/L2 write-back me rged with PCI master post- write to minimize DRAM utilization  Delay transaction from PCI master reading DRAM  Read caching for PCI master reading DRAM  Transaction timer for fair arbitration betw een PCI masters (granularity of two PCI clocks)  Symmetric a ...

  • Intel ECB-862 - page 22

    ECB-862/862L ECB-862/862L User’s Manual 11 2.3.8 Ethernet 2.3.8.1 Realtek RTL8100B Ethernet Controller The Realtek RTL8100B is one of the Real tek RTL8139A/B/C/8130 family, the highly integrated and cost-effective single-chip Fast Ethernet controller t hat provides 32-bit performance, PCI bus master capability, and full compliance with IEEE 802.3 ...

  • Intel ECB-862 - page 23

    User’s Manual 12 ECB-862/862L User’s Manual 2.3.10 Compact Flash Interface A Compact Flash type II connector is connect ed to the secondary IDE controller. The Compact Flash storage card is IDE compatible . It is an ideal replacement for standard IDE hard drives. The solid-state design offers no seek errors even under extreme shock and vibratio ...

  • Intel ECB-862 - page 24

    ECB-862/862L ECB-862/862L User’s Manual 13 3. Hardware Configuration This chapter explains you the instructions of how to set up your system. The additional information shows you how to install M-Syst ems’ DiskOnChip and program the Watchdog Timer. 3.1 Installation Procedure 1. Turn off the power supply. 2. Insert the DIMM module (be careful wi ...

  • Intel ECB-862 - page 25

    User’s Manual 14 ECB-862/862L User’s Manual 3.3 Socket 370 Processor 3.3.1 Installing Pentium III / Celeron CPU  Lift the handling lever of CPU socket outwards and upwards to the other end.  Align the processor pins with pin holes on the socket. Make sure that the notched corner or dot mark (pin 1) of the CP U corresponds to the socket’ ...

  • Intel ECB-862 - page 26

    ECB-862/862L ECB-862/862L User’s Manual 15 3.5 M-Systems’ DiskOnChip Flash Disk ECB-862 reserves a 32-pin DIP socket to suppor t M-Systems’ DiskOnChi p flash disk up to 1 GB. The DiskOnChip is based on pure ISA bus and without PnP (Plug and Play) function. Before the installation, make sure that t he DiskOnChip I/O address ju mper is set prop ...

  • Intel ECB-862 - page 27

    User’s Manual 16 ECB-862/862L User’s Manual 3.6.1 Drivers Support ECB-862 provides on CD-Title to support on- board VGA and Ethernet device drivers in various operating systems. Before installing t he device drivers, please see the reference files in each sub-directory. You cannot install drivers from CD-Title directly. ...

  • Intel ECB-862 - page 28

    ECB-862/862L ECB-862/862L User’s Manual 17 3.7 Jumper & Connector 3.7.1 Jumper & Connector Layout ...

  • Intel ECB-862 - page 29

    User’s Manual 18 ECB-862/862L User’s Manual 3.7.2 Jumper & Connector List Connectors on the board are linked to external devices such as hard disk drives, keyboard, mouse, or floppy drives. In addition, the board has a number of jumpers that allow you to configure your system to suit your application. The following tables list the function ...

  • Intel ECB-862 - page 30

    ECB-862/862L ECB-862/862L User’s Manual 19 Connectors Label Function Note AUDIO1 Audio / TV output connector 8 x 2 box header, pitch 2.54mm CD1 CD-ROM audio input connector 4 x 1 wafer, pitch 2.0mm CN1 Primary IDE connector 20 x 2 box header, pitch 2.54mm CN2 Floppy connector 17 x 2 box header, pitch 2.54mm CN3 Power on connector 2 x 1 header, pi ...

  • Intel ECB-862 - page 31

    User’s Manual 20 ECB-862/862L User’s Manual 3.8 Setting Jumpers You can configure your board to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “clo s ...

  • Intel ECB-862 - page 32

    ECB-862/862L ECB-862/862L User’s Manual 21 3.8.1 External Speaker Select (CN10) CN10 is a 4-pin connector for an external speaker. If there is no external speaker, the ECB-862 provides an onboard buzzer as an alter native. To enable the buzzer, set pin 3-4 as closed. External Speaker Select (CN10) External speaker Onboard buzzer* * default 3.8.2 ...

  • Intel ECB-862 - page 33

    User’s Manual 22 ECB-862/862L User’s Manual 3.8.3 Clear CMOS (J3) You can use J3 to clear the CMOS data if nece ssary. To reset the CMOS data, set J3 to 2- 3 closed for just a few seconds, and then remove the jumper back to 1-2 closed. Clear CMOS (J3) Protect* Clear CMOS * default 3.8.4 Compact Flash Mode Select (J5) You can use J5 to configure ...

  • Intel ECB-862 - page 34

    ECB-862/862L ECB-862/862L User’s Manual 23 3.9 Connector Definitions 3.9.1 Audio / TV Output Connector (AUDIO1) Signal PIN Signal Mic 1 2 Mic Bias AGND 3 4 AGND Line-Out L 5 6 Line-Out R SPK L 7 8 SPK R Line-In L 9 10 Line-In R AGND 11 12 Yout GND 13 14 Cout GND 15 16 COMP 3.9.2 CD-ROM Audio Input Connector (CD1) Signal PIN CD_GND 1 CD_L 2 CD_GND ...

  • Intel ECB-862 - page 35

    User’s Manual 24 ECB-862/862L User’s Manual 3.9.3 Primary IDE Connector (CN1) Signal PIN Signal RESET# 1 2 GND PDD7 3 4 PDD8 PDD6 5 6 PDD9 PDD5 7 8 PDD10 PDD4 9 10 PDD11 PDD3 11 12 PDD12 PDD2 13 14 PDD13 PDD1 15 16 PDD14 PDD0 17 18 PDD15 GND 19 20 NC PDDREQ 21 22 GND PDIOW# 23 24 GND PDIOR# 25 26 GND PDIORDY 27 28 IDESEL PDDACK# 29 30 GND IRQ14 ...

  • Intel ECB-862 - page 36

    ECB-862/862L ECB-862/862L User’s Manual 25 3.9.4 Secondary IDE Connector (CN5) Signal PIN Signal RESET# 1 2 GND SDD7 3 4 SDD8 SDD6 5 6 SDD9 SDD5 7 8 SDD10 SDD4 9 10 SDD11 SDD3 11 12 SDD12 SDD2 13 14 SDD13 SDD1 15 16 SDD14 SDD0 17 18 SDD15 GND 19 20 NC SDDREQ 21 22 GND SDIOW# 23 24 GND SDIOR# 25 26 GND SDIORDY 27 28 IDESEL SDDACK# 29 30 GND IRQ15 ...

  • Intel ECB-862 - page 37

    User’s Manual 26 ECB-862/862L User’s Manual 3.9.5 Signal Description – Primary & Secondary IDE Connector (CN1, CN5) PDA [2:0] Primary Disk Address [2:0]. These signals indicate which byte in either the ATA command block or control block is being addressed. If the IDE signals are configured for Primary and Secondary, these signals are conn ...

  • Intel ECB-862 - page 38

    ECB-862/862L ECB-862/862L User’s Manual 27 PDIOR# Primary Disk IO Read. In normal IDE this is the command to the IDE device that it may drive data onto the PDD [15:0] lines. Data is latched by PIIX4 on the negation edge of PDIOR#. The IDE device is selected either by the ATA regist er file chip selects (PDCS1#, PDCS3#) and the PDA [2:0] lines, or ...

  • Intel ECB-862 - page 39

    User’s Manual 28 ECB-862/862L User’s Manual PDIORDY Primary IO Channel Ready . In normal IDE mode, this input signal is directly driven by the corresponding IDE device IORDY signal. In an Ultra DMA/33 read cycle, this signal is used as STROBE, with the PIIX4 latching data on rising and falling edges of STROBE. In an Ultra DMA/33 write cycle, th ...

  • Intel ECB-862 - page 40

    ECB-862/862L ECB-862/862L User’s Manual 29 SDDACK# Secondary DMA Acknowledge. This signal directly drives the IDE device DMACK# signal. It is asserted by PIIX4 to indicate to IDE DMA slave devices that a gi ven data transfer cycle (assertion of SDIOR# or SDIOW#) is a DMA data transfer cycle. This signal is used in conjunction with the PCI bus mas ...

  • Intel ECB-862 - page 41

    User’s Manual 30 ECB-862/862L User’s Manual 3.9.7 Signal Description – Floppy Connector (CN2) RDATA# The read data input signal from the FDD. WD# Write data. This logic low open drain writes pr e-compensation serial data to the selected FDD. An open drain output. WE# Write enable. An open drain output. MOA# Motor A On. When set to 0, this pin ...

  • Intel ECB-862 - page 42

    ECB-862/862L ECB-862/862L User’s Manual 31 3.9.10 Parallel Port Connector (CN6) Signal PIN Signal STB# 1 2 AFD# PD0 3 4 ERR# PD1 5 6 INIT# PD2 7 8 SLIN# PD3 9 10 GND PD4 11 12 GND PD5 13 14 GND PD6 15 16 GND PD7 17 18 GND ACK# 19 20 GND BUSY 21 22 GND PE 23 24 GND SLCT 25 26 NC 3.9.11 Signal Description – Parallel Port Connector (CN6) PD [7:0] ...

  • Intel ECB-862 - page 43

    User’s Manual 32 ECB-862/862L User’s Manual 3.9.12 Serial Port 2 Connector (CN7) Signal PIN Signal DCD 1 2 Rx D TxD 3 4 DTR GND 5 6 DSR RTS 7 8 CTS RI 9 10 NC 3.9.13 Serial Port 2 with External DB9 Connector (CN7) Signal PIN Signal GND 5 9 RI DTR 4 8 CTS TxD 3 7 RTS RxD 2 6 DSR DCD 1 3.9.14 HDD LED (CN8) SIGNAL PIN HDLED 2 +3.3V 1 3.9.15 Power ...

  • Intel ECB-862 - page 44

    ECB-862/862L ECB-862/862L User’s Manual 33 3.9.16 System Fan Connector (CN12) SIGNAL PIN GND 1 +12V 2 TAC 3 3.9.17 Daughter Board Connector A (CN13) Signal PIN Signal USBP4P B 1 2 USBP3P B USBP4N B 3 4 USBP3N B USBV4 5 6 USBV3 GND 7 8 GND USBP2P B 9 10 USBP1P B USBP2N B 11 12 USBP1N B USBV2 13 14 USBV1 GND 15 16 GND VCCSB 17 18 SLED2 LLED2 19 20 ...

  • Intel ECB-862 - page 45

    User’s Manual 34 ECB-862/862L User’s Manual 3.9.19 10/100 BASE-Tx Ethern et Connector (CN16) Signal PIN TxD+ 1 TxD- 2 RxD+ 3 NC 4 NC 5 RxD- 6 NC 7 NC 8 3.9.20 Signal Description – 10/100Base-Tx Ethernet Connector (CN16) TXD+ / TXD- Ethernet 10/100Base-Tx differential transmitter outputs. RXD+ / RXD- Ethernet 10/100Base-Tx differential receive ...

  • Intel ECB-862 - page 46

    ECB-862/862L ECB-862/862L User’s Manual 35 3.9.23 USB Connector (CN19) Signal PIN CH1 CH2 Signal VCC1 1 2 VCC2 D1- 3 4 D2- D1+ 5 6 D2+ GND 7 8 GND GND 9 10 NC 3.9.24 VGA Connector (CN20) Signal PIN Signal 6 ANA-GND RED 1 11 NC 7 ANA-GND GREEN 2 12 DDCDAT 8 ANA-GND BLUE 3 13 HSYNC 9 VCC NC 4 14 VSYNC 10 DIG-GND DIG-GND 5 15 DDCCLK 3.9.25 Signal De ...

  • Intel ECB-862 - page 47

    User’s Manual 36 ECB-862/862L User’s Manual 3.9.26 LCD Panel Connector (CN21) Signal PIN Signal ENBKL 39 40 ENVEE M 37 38 LP SHFCLK 35 36 FLM GND 33 34 GND P22 31 32 P23 P20 29 30 P21 P18 27 28 P19 P16 25 26 P17 P14 23 24 P15 P12 21 22 P13 P10 19 20 P11 P8 17 18 P9 P6 15 16 P7 P4 13 14 P5 P2 11 12 P3 P0 9 10 P1 VCON 7 8 GND +3.3V 5 6 +3.3V GND ...

  • Intel ECB-862 - page 48

    ECB-862/862L ECB-862/862L User’s Manual 37 3.9.27 LCD Panel Connector Description (CN21) PIN 24-bit TFT 18-bit TFT P23 B0 P22 B1 P21 G0 P20 G1 P19 R0 P18 R1 P17 B2 B0 P16 B3 B1 P15 G2 G0 P14 G3 G1 P13 R2 R0 P12 R3 R1 P11 B4 B2 P10 B5 B3 P9 B6 B4 P8 B7 B5 P7 G4 G2 P6 G5 G3 P5 G6 G4 P4 G7 G5 P3 R4 R2 P2 R5 R3 P1 R6 R4 P0 R7 R5 3.9.28 CPU Fan Connec ...

  • Intel ECB-862 - page 49

    User’s Manual 38 ECB-862/862L User’s Manual 3.9.29 LCD Inverter Connector (CN23) Signal PIN +5V 1 VBR 2 ENBKL 3 GND 4 +12V 5 Note: For inverters with adjustable Backlight function, it is possible to control the LCD brightness through the VBR signal (pin 4) controlled by VR2 . Please see the VR2 section for detailed circuitry information. 3.9.30 ...

  • Intel ECB-862 - page 50

    ECB-862/862L ECB-862/862L User’s Manual 39 3.9.32 LCD Contrast Adjustment Connector (VR1) Signal PIN +3.3V 1 VCON 2 GND 3 3.9.33 LCD Backlight Brightness Adjustment Connector (VR2) Signal PIN +5V 1 VBR 2 GND 3 VCC CN23 pin 4 VR2 1 2 3 Variation Resistor (Recommended: 4.7K Ω , >1/16W) ...

  • Intel ECB-862 - page 51

    User’s Manual 40 ECB-862/862L User’s Manual 4. A ward BIOS Setup 4.1 Starting Setup The AwardBIOS™ is immediately activated when you first power on the computer. The BIOS reads the system information contai ned in the CMOS and begins the process of checking out the system and conf iguring it. When it finishes, the BIOS will seek an operating ...

  • Intel ECB-862 - page 52

    ECB-862/862L ECB-862/862L User’s Manual 41 4.2 Using Setup In general, you use the arrow keys to highlight items, press <Enter> to select, use the PageUp and PageDown keys to change entries, pr ess <F1> for help and press <Esc> to quit. The following table provides more detail about how to navigate in the Setup program using the ...

  • Intel ECB-862 - page 53

    User’s Manual 42 ECB-862/862L User’s Manual 4.3 Getting Help Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window press <Esc> or the F1 key again. 4.4 In Case of Problems If, after making and saving system changes with Se tup, you di ...

  • Intel ECB-862 - page 54

    ECB-862/862L ECB-862/862L User’s Manual 43 4.5.1 Setup Items The main menu includes the following main se tup categories. Recall that some systems may not include all entries. 4.5.1.1 Standard CMOS Features Use this menu for basic system configuration. 4.5.1.2 Advanced BIOS Features Use this menu to set the Advanced Features available on your sys ...

  • Intel ECB-862 - page 55

    User’s Manual 44 ECB-862/862L User’s Manual 4.5.1.11 Save & Exit Setup Save CMOS value changes to CMOS and exit setup. 4.5.1.12 Exit Without Save Abandon all CMOS value changes and exit setup. 4.5.2 Standard CMOS Setup The items in Standard CMOS Se tup Menu are divided into 10 ca tegories. Each category includes no, one or more than one set ...

  • Intel ECB-862 - page 56

    ECB-862/862L ECB-862/862L User’s Manual 45 4.5.2.1 Standard CMOS Selection This table shows the selections that y ou can make on the Standard CMOS Selection. Item Options Description Date Month DD YYYY Set the system date. Note that the ‘Day’ automatically changes when you set the date Time HH : MM : SS Set the s ystem time IDE Primary Master ...

  • Intel ECB-862 - page 57

    User’s Manual 46 ECB-862/862L User’s Manual 4.5.2.2 IDE Adapters The IDE adapters control the hard disk drive. Use a separate sub menu to configure each hard disk drive. Figure 2 shows the IDE pr imary master sub menu. Use the legend keys to navigate through this menu and exit to the main menu. Use Table 3 to configure the hard disk. Item Optio ...

  • Intel ECB-862 - page 58

    ECB-862/862L ECB-862/862L User’s Manual 47 4.5.3 Advanced CMOS Setup Defaults This Setup includes all of the advanced featur es in the system. The detail descriptions are specified as below. Figure 3: The Advanced CMOS Features 4.5.3.1 Virus Warning Allows you to choose the VIRUS Warning featur e for IDE Hard Disk boot sector protection. If this ...

  • Intel ECB-862 - page 59

    User’s Manual 48 ECB-862/862L User’s Manual 4.5.3.2 CPU Internal Cache/External Cache These two categories speed up memory acce ss. However, it depends on CPU/chipset design. Enabled Enable cache Disabled Disable cache 4.5.3.3 Quick Power On Self Test This category speeds up Power On Self Test (POST) after you power up the computer. If it is se ...

  • Intel ECB-862 - page 60

    ECB-862/862L ECB-862/862L User’s Manual 49 4.5.3.9 Typematic Rate Setting Key strokes repeat at a rate determined by the keyboard controller. When enabled, the typematic rate and typematic delay can be selected. The choice: Enabled/Disabled. 4.5.3.10 Typematic Rate (Chars/Sec) Sets the number of times a second to repeat a key stroke when you hold ...

  • Intel ECB-862 - page 61

    User’s Manual 50 ECB-862/862L User’s Manual 4.5.3.15 Report No FDD for Win 95 While the FDD in “ STANDARD CMOS SETUP ” is set to NONE, set this option to No to release IRQ6 for passing Win95 logo. This opt ion is irrelevant under normal operation. The choice: Yes, No. 4.5.3.16 Small Logo (EPA) Show When you select “ Enabled” the screen ...

  • Intel ECB-862 - page 62

    ECB-862/862L ECB-862/862L User’s Manual 51 4.5.4 Advanced Chipset Setup Defaults This Setup is very important to keep system’s stability. If y ou are not technical person, do not attempt to change any parameters. The best way is to choose optimal default setting. Figure 4: The Advanced Chipset Features This section allows you to configure the s ...

  • Intel ECB-862 - page 63

    User’s Manual 52 ECB-862/862L User’s Manual 4.5.4.1 DRAM Timing Selectable If your DIMM memory has SPD (Serial Presenc e Detect) 8-pin IC on module, you can set this option to “By SPD”. System will set y our SDRAM clock and timing from the SPD IC. If the option set as ”Manual”, DRAM clock and timing must be set from items below: The cho ...

  • Intel ECB-862 - page 64

    ECB-862/862L ECB-862/862L User’s Manual 53 4.5.4.8 System BIOS Cacheable Allows the system BIOS to be cac hed for faster system performance. The choice: Enable, Disable. 4.5.4.9 Video BIOS Cacheable Allows the video BIOS to be cached for faster video performance. The choice: Enable, Disable. 4.5.4.10 Video RAM Cacheable Allows the video RAM to be ...

  • Intel ECB-862 - page 65

    User’s Manual 54 ECB-862/862L User’s Manual 4.5.5 Integrated Peripherals Setup Defaults This section describes I/O resources assignm ent for all of on-board peripheral devices. Figure 5: The Integrated Peripherals Features 4.5.5.1 On-Chip Primary/Secondary PCI IDE Select “Enabled” to activate each on-board ID E channel separately, Se lect ? ...

  • Intel ECB-862 - page 66

    ECB-862/862L ECB-862/862L User’s Manual 55 4.5.5.4 USB Controller Select Enabled if your system contains a Universal Serial Bus (USB) controller. The choice: Enable, Disable. 4.5.5.5 USB Keyboard Support This item lets you enable or disable the USB keyboard driver within the onboard BIOS. The choice: Enable, Disable. 4.5.5.6 Init Display First Se ...

  • Intel ECB-862 - page 67

    User’s Manual 56 ECB-862/862L User’s Manual 4.5.5.8 POWER ON Function This field allows you to use the keyboard to power-on the system. Use Table 3 to configure this function. Item Options Description Password Press Enter When this option is selected, move the cursor to the "KB Power On Password" field and press <Enter>. Enter y ...

  • Intel ECB-862 - page 68

    ECB-862/862L ECB-862/862L User’s Manual 57 4.5.5.13 IR Transmission Delay If this option is enabled, transmission of data will be slower. This is recommended when you encounter transmission problem with your device. The choice: Disable, Enable. 4.5.5.14 UR2 Duplex Mode Select to activate the Infrared transfer function. This default setting is “ ...

  • Intel ECB-862 - page 69

    User’s Manual 58 ECB-862/862L User’s Manual 4.5.5.20 PWRON After PWR-Fail Select the option for the system action after an AC power failure. Off When power returns after an AC power failure, the system's power is off. You must press the Power button to power-on the system. On When power returns after an AC power failure, the system will au ...

  • Intel ECB-862 - page 70

    ECB-862/862L ECB-862/862L User’s Manual 59 4.5.6.1 ACPI Function This item allows you to enable or disabl e the function of Advanced Configuration and Power Interface (ACPI) that offers improved power management. The choice: Disable, Enable. 4.5.6.2 ACPI Suspend Type This field is used to select the type of Suspend function. S1 (POS) Enables the ...

  • Intel ECB-862 - page 71

    User’s Manual 60 ECB-862/862L User’s Manual 4.5.6.7 Suspend Type System further shuts down all devices and all right select stop Grant or Power on suspend function. The choice: stop Grant , PowOn Suspend. 4.5.6.8 MODEM Use IRQ This item tells the Power Management BIOS which IRQ is assigned to the installed MODEM. The choice: NA, 3, 4, 5, 7, 9, ...

  • Intel ECB-862 - page 72

    ECB-862/862L ECB-862/862L User’s Manual 61 Note: The computer cannot receive or transmit data until the computer and application are fully running. After the item is set as enabled, the system must enter to OS once before system is turned off. 4.5.6.15 Wake up on LAN This allows you to remotely power up y our systems through your network by sendi ...

  • Intel ECB-862 - page 73

    User’s Manual 62 ECB-862/862L User’s Manual 4.5.7 PnP/ PCI Setup Defaults This section describes configuring the PCI bus system. PCI (Peripheral Component Interconnect) is a system that allows I/O devices to operate at speeds nearing CPU’s when they communicate with own special components. All of options described in th is section are importa ...

  • Intel ECB-862 - page 74

    ECB-862/862L ECB-862/862L User’s Manual 63 4.5.7.3 Resources Controlled By Default setting is “Auto (ESCD)”. This setti ng allows the BIOS to self detect setting and Plug-and-Play devices during st art up. The user can sele ct and configure IRQs under "Manual" mode. The choice: Auto (ESCD), Manual. 4.5.7.4 IRQ Resources These option ...

  • Intel ECB-862 - page 75

    User’s Manual 64 ECB-862/862L User’s Manual 4.5.8 PC Health Status Setup Defaults This setup describes current CPU surface temperature status det ected from hardware monitor sensor. The status showed on screen will include: 4.5.8.1 CPU Warning Temperature Select to enable or disable the hardware moni tor sensor and set the warning temperature. ...

  • Intel ECB-862 - page 76

    ECB-862/862L ECB-862/862L User’s Manual 65 4.5.9.1 Vcore, Vcc3, +5V, + 12V, -12V,-5V, VBAT & 5VSB The onboard hardware monitor is able to detect the voltage output by the voltage regulators. These values refresh upon any key entry. The function is optional. 4.5.9.2 Shutdown Temperature When you select “ enable “, the CPU worki ng temperat ...

  • Intel ECB-862 - page 77

    User’s Manual 66 ECB-862/862L User’s Manual 4.5.9.5 Auto Detect PCI CLK If you have the EMI issue, set t he option as Enabled, it keeps its interference under control. The choice: Disable, Enable. 4.5.9.6 Spread Spectrum Using the setting “ Enabled “, for EMI testing will increase the system stability. The default setting is “ Disabled ? ...

  • Intel ECB-862 - page 78

    ECB-862/862L ECB-862/862L User’s Manual 67 Load Fail-Safe Defaults (Y/N)? N If you want to process, type <Y> and press <Enter>. The default settings will be loaded. 4.5.11 Load Optimized Defaults This feature loads optimized setting from t he BIOS ROM. Use the default values as standard values for your system. Highlight this option in ...

  • Intel ECB-862 - page 79

    User’s Manual 68 ECB-862/862L User’s Manual 4.6 Flash BIOS Utility Utilize Award Flash BIOS progr amming utility to update on-board BIOS for the future new BIOS version. Please contact your technical window to get this utility if necessary. Note: Remark or delete any installed Memory Management Utility (s uch as HIMEM.SYS, EMM386.EXE, QEMM.EXE, ...

  • Intel ECB-862 - page 80

    ECB-862/862L ECB-862/862L User’s Manual 69 5. Driver Inst allation 5.1 Driver Installation for Ethernet Adapter 5.1.1 Windows 9x The best way to install the dr iver for the Ethernet controller is to use the plug and play system of Windows 9x. The following procedures illustrate how the installation can be done. 1. If a driver for the Et hernet co ...

  • Intel ECB-862 - page 81

    User’s Manual 70 ECB-862/862L User’s Manual • If the ‘ Network adapters ’ line is present, expand t he line and remove the PCI Ethernet Adapter. This is done by se lecting the line and clicking the ‘ Remove ’ button. Before removal of the adapter(s), your screen might look like this: • When all adapters are removed (or none we re pr ...

  • Intel ECB-862 - page 82

    ECB-862/862L ECB-862/862L User’s Manual 71 4. Click the ‘ Next ’ button to continue the driver installation. 5. Specify the location of network adapter and click ‘ Next ’ (see below). 6. Click the ‘ Next ’ button to install the network adapter driver. ...

  • Intel ECB-862 - page 83

    User’s Manual 72 ECB-862/862L User’s Manual 7. Click the ‘ Finish ’ button. 8. To complete the installation, r eboot the computer by clicking the ‘ Yes ’ button in the window shown below. 9. Please follow the Procedure 1-8 to install another Ethernet Adapter. 10. After the system restarts, the network adapter should be inst alled. Proto ...

  • Intel ECB-862 - page 84

    ECB-862/862L ECB-862/862L User’s Manual 73 5.2 Driver Installation for Display Adapter 5.2.1 Windows 9x The following steps will install the display driver for the ‘VIA PLE133T ’ display controller. 1. Find the directory of the dr iver disk with VIA PLE133T VGA driver. Double click the icon ‘setup’ on the folder. This should start t he dr ...

  • Intel ECB-862 - page 85

    User’s Manual 74 ECB-862/862L User’s Manual 3. Click the ‘ Next ’ to continue the driver inst all. If you want to stop the installation, click the ‘ Cancel ’ 4. To complete the display driver installa tion, reboot the comput er by clicking the ‘ Finish ’ button in the window shown below. ...

  • Intel ECB-862 - page 86

    ECB-862/862L ECB-862/862L User’s Manual 75 5.2.2 Windows 2000 The following steps will install the display driver for the ‘VIA PLE133T ’ display controller. 1. Find the directory of the driver disk with VIA PLE133T VGA driver. Double click the icon ‘setup’ on the folder. This should start t he driver setup process as shown below: 2. Click ...

  • Intel ECB-862 - page 87

    User’s Manual 76 ECB-862/862L User’s Manual 3. Click the ‘ Next ’ to continue the driver install. If you want to stop the inst allation, click the ‘ Cancel ’ 4. Click the ‘ Yes ’ to continue the driver install. If you want to stop the installation, click the ‘ No ’ ...

  • Intel ECB-862 - page 88

    ECB-862/862L ECB-862/862L User’s Manual 77 5. To complete the display driver installa tion, reboot the comput er by clicking the ‘ Finish ’ button in the window shown below. ...

  • Intel ECB-862 - page 89

    User’s Manual 78 ECB-862/862L User’s Manual 5.3 Driver Installation for USB2.0 Adapter 5.3.1 Windows 9x The following steps will install the display dr iver for the VIA VT6202 USB2.0 controller. 1. Find the directory of the driver disk with VIA VT6202 USB2.0 driver. Double click the icon ‘setup’ on the folder. This should start the driver s ...

  • Intel ECB-862 - page 90

    ECB-862/862L ECB-862/862L User’s Manual 79 3. Click the ‘ Next ’ to continue the driver install. If you want to stop the inst allation, click the ‘ Cancel ’ 4. To complete the USB Adapter driver installation, reboot the computer by clicking the ‘ Finish ’ button in the window shown below. ...

  • Intel ECB-862 - page 91

    User’s Manual 80 ECB-862/862L User’s Manual 5.3.2 Windows 2000 The following steps will install the display dr iver for the VIA VT6202 USB2.0 controller. 1. Find the directory of the driver disk with VIA VT6202 USB2.0 driver. Double click the icon ‘setup’ on the folder. This should start the driver setup process as shown below: 2. Click the ...

  • Intel ECB-862 - page 92

    ECB-862/862L ECB-862/862L User’s Manual 81 3. Click the ‘ Yes ’ to continue the driver install. If you want to stop the installation, click the ‘ No ’ 4. Click the ‘ Next ’ to continue the driver install. If you want to stop the inst allation, click the ‘ Cancel ’ ...

  • Intel ECB-862 - page 93

    User’s Manual 82 ECB-862/862L User’s Manual 5. Click the ‘ Yes ’ to continue the driver install. If you want to stop the installation, click the ‘ No ’ 6. To complete the USB Adapter driver installation, reboot the computer by clicking the ‘ Print to File ’ button in the window shown below. ...

  • Intel ECB-862 - page 94

    ECB-862/862L ECB-862/862L User’s Manual 83 5.4 Driver Installation for Audio Adapter 5.4.1 Windows 9X The following steps will install the display dr iver for the VIA VT82C686B Audio controller. 1. Find the directory of the driver disk with VIA VT82C686B Audio driver. Double click the icon ‘setup’ on the folder. This should start the driver s ...

  • Intel ECB-862 - page 95

    User’s Manual 84 ECB-862/862L User’s Manual 3. Click the ‘ Next ’ to continue the driver install. If you want to stop the inst allation, click the ‘ Cancel ’ 4. To complete the display driver installa tion, reboot the comput er by clicking the ‘ Finish ’ button in the window shown below. ...

  • Intel ECB-862 - page 96

    ECB-862/862L ECB-862/862L User’s Manual 85 5.4.2 Windows 2000 The following steps will install the display dr iver for the VIA VT82C686B Audio controller. 1. Find the directory of the driver disk with VIA VT82C686B Audio driver. Double click the icon ‘setup’ on the folder. This should start the driver setup process as shown below: 2. Click th ...

  • Intel ECB-862 - page 97

    User’s Manual 86 ECB-862/862L User’s Manual 3. Click the ‘ Next ’ to continue the driver install. If you want to stop the inst allation, click the ‘ Cancel ’ 4. To complete the display driver installa tion, reboot the comput er by clicking the ‘ Finish ’ button in the window shown below. ...

  • Intel ECB-862 - page 98

    ECB-862/862L ECB-862/862L User’s Manual 87 6. Measurement Drawing ...

  • Intel ECB-862 - page 99

    User’s Manual 88 ECB-862/862L User’s Manual Appendix A: BIOS Revisions BIOS Rev. New Features Bugs/Problems Solved Known Problems ...

  • Intel ECB-862 - page 100

    ECB-862/862L ECB-862/862L User’s Manual 89 Appendix B: System Resources Memory Map The following table indicates memory map of ECB-862. The address ranges specify the runtime code length. Address Range Description Note 00000000h-0009FFFFh System board extension for ACPI BIOS 000A0000h-000AFFFFh VIA Tech VT8361/VT8601 Graphics Controller 000B0000h ...

  • Intel ECB-862 - page 101

    User’s Manual 90 ECB-862/862L User’s Manual I/O – Map Certain I/O addresses are subject to change during boot as PnP managers may relocate devices or functions. The addresses shown in the table are typical locations. I/O Port Description Note 0000h-000Fh Direct memory access controller 0010h-001Fh Motherboard resources 0020h-0021h Programmabl ...

  • Intel ECB-862 - page 102

    ECB-862/862L ECB-862/862L User’s Manual 91 I/O Port Description Note 03F6h-03F6h VIA Bus Master PCI IDE Controller 03F7h-03F7h Standard Floppy Disk Controller 03F8h-03FFh Communications Port (COM1) 04D0h-04D1h Motherboard resources 0CF8h-0CFFh PCI bus 1000h-101Fh VIA Tech 3038 PCI to USB Universal Host Controller 4000h-407Fh PCI bus 4080h-40FFh P ...

  • Intel ECB-862 - page 103

    User’s Manual 92 ECB-862/862L User’s Manual Interrupt Usage. The actual interrupt settings depend on the Pn P handler, the table below indicates the typical settings. Interrupt Description Note 00 System timer 01 Standard 101/102-Key or Microsoft Natural PS/2 Keyboard 02 Programmable interrupt controller 03 Communications Port (COM2) 04 Communi ...

  • Intel ECB-862 - page 104

    ECB-862/862L ECB-862/862L User’s Manual 93 Appendix C: A W ARD BIOS POST Messages During the Power On Self-Test (POST), if the BIOS detects an error requiring you to do something to fix, it will either sound a beep code or display a message. If a message is displayed, it will be accompanied by: PRESS F1 TO CONTINUE, CTRL-ALT-ESC OR DEL TO ENTER S ...

  • Intel ECB-862 - page 105

    User’s Manual 94 ECB-862/862L User’s Manual Display Switch Is Set Incorrectly Display switch on the motherboard can be set to either monochrome or color. This indicates the switch is set to a different setting than indicated in Setup. Determine which setting is correct, and then either turn o ff the system and change t he jumper, or enter Setup ...

  • Intel ECB-862 - page 106

    ECB-862/862L ECB-862/862L User’s Manual 95 Invalid EISA Configuration Please Run EISA Configuration Utility The non-volatile memory containing EISA c onfiguration information was programmed incorrectly or has become corrupt. Re-run EI SA configuration utility to correctly program the memory. NOTE: When this error appears, the system will boot in ...

  • Intel ECB-862 - page 107

    User’s Manual 96 ECB-862/862L User’s Manual Press A Key To Reboot This will be displayed at the bottom screen w hen an error occurs that requires you to reboot. Press any key and the system will reboot. Press F1 To Disable NMI, F2 To Reboot When BIOS detects a Non-maskable Interrupt condition during boot, this will allow you to disable the NMI ...

  • Intel ECB-862 - page 108

    ECB-862/862L ECB-862/862L User’s Manual 97 Wrong Board In Slot Please Run EISA Configuration Utility The board ID does not match the ID st ored in the EISA non-volatile memory. NOTE: When this error appears, the system will boot in ISA mode, which allows you to run the EISA Configuration Utility. Floppy Disk(s) Fail (80) → Unable To Reset Flopp ...

  • Intel ECB-862 - page 109

    User’s Manual 98 ECB-862/862L User’s Manual Appendix D: A W ARD BIOS POST Codes POST Code (hex) Description CFh Test CMOS R/W functionality. C0h Early chipset initialization: -Disable shadow RAM -Disable L2 cache (socket 7 or below) -Program basic chipset registers C1h Detect memory -Auto-detection of DRAM size, type and ECC. -Auto-detection of ...

  • Intel ECB-862 - page 110

    ECB-862/862L ECB-862/862L User’s Manual 99 POST Code (hex) Description 12h Use walking 1’s algorithm to check out interface in CMOS circuitry. Also set real-time clock power status, and then check for override. 13h Reserved 14h Program chipset default values into chipset. Chipset default values are MODBINable by OEM customers. 15h Reserved 16h ...

  • Intel ECB-862 - page 111

    User’s Manual 100 ECB-862/862L User’s Manual POST Code (hex) Description 28h Reserved 29h 1. Program CPU internal MTRR (P6 & PII) for 0-640K memory address. 2. Initialize the APIC fo r Pentium class CPU. 3. Program early chipset according to CMOS setup. Example: onboard ID E controller. 4. Measure CPU speed. 5. Invoke video BIOS. 2Ah Reserv ...

  • Intel ECB-862 - page 112

    ECB-862/862L ECB-862/862L User’s Manual 101 POST Code (hex) Description 49h 1. Calculate total memory by testi ng the last double word of each 64K page. 2. Program writes allocation for AMD K5 CPU. 4Ah Reserved 4Bh Reserved 4Ch Reserved 4Dh Reserved 4Eh 1. Program MTRR of M1 CPU 2. Initialize L2 cache for P6 class CPU & program CPU with prope ...

  • Intel ECB-862 - page 113

    User’s Manual 102 ECB-862/862L User’s Manual POST Code (hex) Description 66h Reserved 67h Prepare memory size information for function call: INT 15h ax=E820h 68h Reserved 69h Turn on L2 cache 6Ah Reserved 6Bh Program chipset registers according to items described in Setup & Auto-configuration table. 6Ch Reserved 6Dh 1. Assign resources to a ...

  • Intel ECB-862 - page 114

    ECB-862/862L ECB-862/862L User’s Manual 103 POST Code (hex) Description 82h 1. Call chipset power management hook. 2. Recover the text fond used by EPA logo (not for full screen logo) 3. If password is set, ask for password. 83h Save all data in stack back to CMOS 84h Initialize ISA PnP boot devices 85h 1. USB final Initialization 2. NET PC: Buil ...

Manufacturer Intel Category Computer Hardware

Documents that we receive from a manufacturer of a Intel ECB-862 can be divided into several groups. They are, among others:
- Intel technical drawings
- ECB-862 manuals
- Intel product data sheets
- information booklets
- or energy labels Intel ECB-862
All of them are important, but the most important information from the point of view of use of the device are in the user manual Intel ECB-862.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Intel ECB-862, service manual, brief instructions and user manuals Intel ECB-862. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Intel ECB-862.

Similar manuals

A complete manual for the device Intel ECB-862, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Intel ECB-862 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Intel ECB-862.

A complete Intel manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Intel ECB-862 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Intel ECB-862, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Intel ECB-862, that we can find in the current document
3. Tips how to use the basic functions of the device Intel ECB-862 - which should help us in our first steps of using Intel ECB-862
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Intel ECB-862
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Intel ECB-862 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Intel ECB-862?

Use the form below

If you did not solve your problem by using a manual Intel ECB-862, ask a question using the form below. If a user had a similar problem with Intel ECB-862 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)