English dropdown-ico

Manual Hawking HGMS224

128 pages 4.99 mb
Download

Go to site of 128

Summary
  • Hawking HGMS224 - page 1

    1 ...

  • Hawking HGMS224 - page 2

    FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These lim itations are designed to provide reasonable protection against harmful interference in a residential installation. This equipm ent generates, uses and can radiate radio frequency energy and, if ...

  • Hawking HGMS224 - page 3

    3 no warranty or representation, expressed, implied or statutory, with respect to its products or the contents or use of this documentation and all accompanying software, and specifically disclaim s its quality, performance, merchantability, or fitness for any particular purpose. Hawking Technology reserves the right to revise or update its product ...

  • Hawking HGMS224 - page 4

    1. Introduction 7 2. Package Contents 8 3. Hardware Installation 9 4. Initial Setup for Management 11 4.1 Out-of-band Terminal Mode Configuration 11 4.2 In-band Management through Ethernet 12 4.3 Telnet Management 14 5. Web Management 16 5.1 Web Management Home Page Overview 16 5.2 Port Status 17 5.3 Port Statistics 19 5.4 Administrator 20 5.4.1 IP ...

  • Hawking HGMS224 - page 5

    5.4.10 SNMP/Trap Manager 48 5.4.11 Security Manager 49 5.4.12 802.1x Configuration 50 5.4.13 Web Cluster 53 5.5 TFTP Firmware Update 55 5.6 Configuration Backup 56 5.6.1 TFTP Restore Configuration 56 5.6.2 TFTP Backup Configuration 56 5.7 Reset System 57 5.8 Reboot 57 6. Console – Firmware Update 58 7. Out-of-band Management 61 7.1 Main Menu 62 7 ...

  • Hawking HGMS224 - page 6

    7.2.8 MAC Address Configuration 87 7.2.8.1 Static MAC Address 87 7.2.8.2 Filtering MAC Address 91 7.3 Protocol Related Configuration 95 7.3.1 Spanning-Tree Protocol 95 7.3.1.1 Enabling STP 96 7.3.1.2 STP System Configuration 97 7.3.1.3 Per Port Configuration 98 7.3.2 SNMP 99 7.3.2.1 System Options 100 7.3.2.2 Community Strings 101 7.3.2.3 Trap Mana ...

  • Hawking HGMS224 - page 7

    Hawking Technologies’ HGMS224 24-Port 10/100 Layer 2 Managed Switch ( Intelligent ) + 2- Port Gigabit Module Slot is a high performance, web-m anaged SNMP (simple network management protocol) Layer 2 switch that provides users with (24) 10/100Mbps Ethernet ports and (2) 1000Mbps gigabit ports. The switch features SNMP management and remote contro ...

  • Hawking HGMS224 - page 8

    The complete HGMS224 package consists of: x One HGMS224 24-Port 10/100 Layer 2 Managed Switch ( Intelligent ) + 2-Port Gigabit Module Slot x Rack mount kit: 2 mounting brackets and screws x Four rubber feet with adhesive backing x One AC power cord x One RS-232 cable x One user’s manual x One CD Check to make sure that the un ...

  • Hawking HGMS224 - page 9

    Please follow the guidelines below when choosing a location to install the switch: x The surface must support at least 3 kg. Do not place heavy objects on the switch. x Visually inspect the power cord and AC power connector. x Make sure that there is proper heat dissipation from and adequate ventilation around the switch. Desktop or Shelf ...

  • Hawking HGMS224 - page 10

    x If the fans are working properly, the “Fan” LEDs will remain unlit. If either or both of the fans stop or fail, the corresponding “Fan” LED(s) will be lit red. LED Indicators St a t u s LED Color Solid Blinking Power Green The device is powered on N/A Diagnostic Green Self diagnostic successful Performing self diagnostic (after power o ...

  • Hawking HGMS224 - page 11

    There are two ways to perform the initial setup for the Switch: a. “Out-of-Band Configuration” - connect y our PC’s serial port to the switch’s console port with the included RS-232 serial cable and run the terminal communication program b. “In-Band Configuration”- network a PC to the switch and run a web browser or telnet. The sections ...

  • Hawking HGMS224 - page 12

    4.2 In-band Configuration through Ethernet In addition to terminal mode configuration, the switch also supports in-band configuration via a web browser. Web browser configuration is easier than terminal mode configuration because the user can simply connect the network-ready PC to the switch, open the web browser, go to the switch’s configuration ...

  • Hawking HGMS224 - page 13

    Modify the Switch’s IP Address via the Out-of-Band Method 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Log into the console (default username: admin, default password: 123). Use the Tab key to select (highlight) “Switch Static Configuration” and hit Enter . Use the Tab key to select “Administration Configuration” and hit Enter . Use the Tab key to ...

  • Hawking HGMS224 - page 14

    4.3 Telnet Management In addition to local terminal mode operation, the switch supports remote m anagement through Telnet over the network or even over the Internet for browser-less environments. In this mode, before executing the Telnet program, you will again be asked to modify the IP Configuration settings as required for management via a web br ...

  • Hawking HGMS224 - page 15

    15 ...

  • Hawking HGMS224 - page 16

    5.1 Web Management Home Page Overview Connection Icon From this page, you can view the link status of every port on the switch. If a given port is linked, it will be represented by a connection icon (see figure above) within the switch diagram/diagnostic at the top of the page. In the column on the left side of the page, you can click on the functi ...

  • Hawking HGMS224 - page 17

    5.2 Port Status This page provides a display of the current status of every port on the switch. The status depends on the user settings and the negotiation results. 1. State: Displays port status: either disabled or enabled . “Unlink” will be treated as “off ”. 2. Link Status: “ Down” indicates that the port is not linked, “Up” indi ...

  • Hawking HGMS224 - page 18

    7. Rate Control (100K): Displays the rate control setting. “Ingr”: Displays the port’s effective ingress rate. “Egr”: Display the port’s effective egress rate. 8. Port Security: Display the port security is enabled or disabled. 9. Config (located beneath the “Flow Control” category) : Displays the state of the user settings. 10. Act ...

  • Hawking HGMS224 - page 19

    5.3 Port Statistics This page provides a display of the current status of the entire unit. Press the Reset button to clear all counters on this page. 19 ...

  • Hawking HGMS224 - page 20

    5.4 Administrator Many of the management functions can be set or performed by clicking on Administrator in the left column of the page. Once you have clicked on Administrator , you will see a menu that includes the following categories:  IP Address  Switch Settings  Console Port Info  Port Controls  Trunking  Fil ...

  • Hawking HGMS224 - page 21

    5.4.2 Switch Settings 5.4.2.1 Basic All information in the Basic section is read-only. Therefore, you will not be able to modify its contents. Description: Displays what type of device you are using. MAC Address: The unique hardware address assigned by the manufacturer (default). Firmware Version: Displays the firmware version of the switch. Hardwa ...

  • Hawking HGMS224 - page 22

    5.4.2.2 Module Info All information in the Module Info section is read only. Therefore, you will not be able to modify its contents. Its purpose is to display the module card information. 5.4.2.3 Advanced  Miscellaneous Settings: MAC Table Address Entry: Age-out Time: Type in the number of seconds that an inactive MAC address remains in the s ...

  • Hawking HGMS224 - page 23

    Broadcast Storm Filter Mode: To configure broadcast storm control, enable it and set the upper threshold for individual ports. The threshold is the percentage of the port's total bandwidth used by broadcast traffic. When broadcast traffic for a port rises above the threshold you set, broadcast storm control becomes active. The valid threshold ...

  • Hawking HGMS224 - page 24

    Enable Delay Bound: Limit the queuing time of low priority packets in the switch. The default “Max Delay Time” is 255ms. If the low priority packet stays in the switch longer than the “Max Delay Time”, it will be sent. The valid range is 1-255ms. QoS Policy: High Priority Levels – Priority levels from 0-7 can be mapped to high or low queu ...

  • Hawking HGMS224 - page 25

    5.4.3 Console Port Information The Console has a standard UART interface to communicate with the serial port. You can use the Windows HyperTerminal program to establish a link to the switch. Connect To -> Configure: Bits per seconds: 9600 Data bits: 8 Parity: none Stop Bits: 1 Flow control: none 25 ...

  • Hawking HGMS224 - page 26

    5.4.4 Port Controls User may modify or change mode operation in this page. 1. State: You can enable or disable the port control for each port. 2. Auto Negotiation: You can set the auto negotiation mode to Auto, N-way (specify the speed/duplex on a specific port and enable auto-negotiation), or Force for each port. 3. Speed: You can set the speed at ...

  • Hawking HGMS224 - page 27

    6. Rate Control: Ports 1-24 support ingress and egress rate control for each port. For example, assume that Port 1 is set at 10Mbps. You can set its effective egress rate at 1Mbps and ingress rate at 500Kbps. The device will perform flow control or backpressure to confine the ingress rate to the specified rate. Ingress: Type the effective ingress r ...

  • Hawking HGMS224 - page 28

    5.4.5 Trunking The Link Aggregation Control Protocol (LACP) provides a standardized means for: a. exchanging information between partner systems on a link, to allow their Link Aggregation Control instances to reach agreement on the identity of the Link Aggregation Group to which the link belongs, b. moving the link to that Link Aggregation Group, a ...

  • Hawking HGMS224 - page 29

    2. Group ID: You can configure up to seven trunk groups. Choose the "Group ID" and click "Get". 3. LACP: If enabled, the group is an LACP static trunking group. If disabled, the group is a local static trunking group. All ports support LACP dynamic trunking groups. If connecting to a device that also supports LACP, the LACP dyna ...

  • Hawking HGMS224 - page 30

    2. The page shown below displays the static trunking groups. 3. The page shown below displays “Actor” and “Partner” trunking. 30 ...

  • Hawking HGMS224 - page 31

    5.4.5.3 State Activity Active (select) : The port automatically sends LACP protocol packets. N/A (not selected) : The port does not automatically sends LACP protocol packets, and responds only if it receives LACP protocol packets from the opposite device. 1. A link that either has two active LACP ports, or one active port can perform dynamic LACP t ...

  • Hawking HGMS224 - page 32

    5.4.6 Filter Database 5.4.6.1 IGMP Snooping The switch supports IP multicasting. You can enable the IGMP protocol in the “IGMP Snooping” section. IGMP snooping information is displayed on this page. You can view different multicast groups, VIDs and member ports in this section. IP multicast addresses range from 224.0.0.0 to 239.255.255.255. 32 ...

  • Hawking HGMS224 - page 33

    The Internet Group Management Protocol (IGMP) is an internal protocol within the Internet Protocol (IP) suite. The IP suite manages multicast traffic by using switches, routers, and hosts that support IGMP. Enabling IGMP allows the ports to detect IGMP queries and report packets, and manage IP multicast traffic through the switch. IGMP has three fu ...

  • Hawking HGMS224 - page 34

    5.4.6.2 S tatic MAC Address When you add a static MAC address, it remains in the switch's address table, regardless of whether or not the device is physically connected to the switch. This saves the switch from having to re-learn a device's MAC address when the disconnected or powered-off device is active on the network again. 1. Click on ...

  • Hawking HGMS224 - page 35

    4. If tag-based (IEEE 802.1Q) VLANs are set up on the switch, static addresses are associated with individual VLANs. Type in the VID (tag-based VLAN ID) to associate with the MAC address. 5. Click the Add button. 5.4.6.3 MAC Filtering MAC address filtering allows the switch to drop unwanted traffic. Traffic is filtered based on the destination addr ...

  • Hawking HGMS224 - page 36

    5.4.7 VLAN Configuration A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast domain. It allows you to isolate network traffic so only members of the VLAN receive traffic from the same VLAN members. Basically, creating a VLAN from a switch is logically equivalent to reconnecting a group of network devices to another Layer 2 ...

  • Hawking HGMS224 - page 37

     Port-based VLAN Packets can only be broadcast among members of the same VLAN group. Note that all unselected ports are treated as belonging to another single VLAN. If the port-based VLAN is enabled, the VLAN-tagging is ignored. 37 ...

  • Hawking HGMS224 - page 38

     Tag-based VLAN (IEEE 802.1Q VLAN) Tag-based VLAN is an IEEE 802.1Q specification standard. Therefore, it is possible to create a VLAN across devices from different switch vendors. IEEE 802.1Q VLAN uses a technique to insert a “tag” into the Ethernet frames. Tags contain a VLAN Identifier (VID) that indicates the VLAN numbers.  Prot ...

  • Hawking HGMS224 - page 39

    5.4.7.1 Port-Based VLAN 39 1. Click Add to create a new VLAN group. 2. Enter the VLAN name and group ID, and select the mem b ers for the new VLAN. 3. Click Apply . 4. If there are more groups than the viewable box can display, you can click Next Page to view other VLAN groups. NOTE: If the trunk groups already exist, you can view them (ex: TRK1, T ...

  • Hawking HGMS224 - page 40

    5.4.7.2 T ag-based (IEEE 802.1Q) VLAN This page, user can create Tag-based VLAN, and enable or disable GVRP protocol. There are 256 VLAN groups to provide configure. Enable 802.1Q VLAN, the all ports on the switch belong to default VLAN, VID is 1. The default VLAN can’t be delete. GVRP (GARP [Generic Attribute Registration Protocol] VLAN Registra ...

  • Hawking HGMS224 - page 41

     Basic Create a VLAN and add tagged member ports to it. 1. Click on the “Basic” tab, and then click Add to reach the page shown below. 2. Type a name for the new VLAN. 3. Type a VID (between 2-4094). The default is 1. 4. Choose the protocol type. 5. From the column box on the left that displays the available ports, select the ports you wo ...

  • Hawking HGMS224 - page 42

    6. Click Next . Then you can view the page as follows: 7. Use this page to set the outgoing frames as VLAN-tagged frames, if necessary. Then click Apply . Tag: outgoing frames that are VLAN-tagged. Untag: outgoing frames that are not VLAN-tagged. 42 ...

  • Hawking HGMS224 - page 43

     Port VID Configure Port VID Settings From the main tag-based (IEEE 802.1Q) VLAN page, click the “Port VID” tab. 43 Port VID (PVID) Set the port VLAN ID that will be assigned to untagged traffic on a given port. This feature is useful for accommodating devices that you want to participate in the VLAN but that don’t support tagging. Each ...

  • Hawking HGMS224 - page 44

    Ingress Filtering Ingress filtering allows frames that belong to a specific VLAN to be forwarded if the port belongs to that VLAN. The switch has two ingress filtering rules. They are as follows: Ingress Filtering Rule 1: Only forward packets with VIDs matching this port’s configured VID. Ingress Filtering Rule 2: Drop untagged frames. 5.4.8 Span ...

  • Hawking HGMS224 - page 45

    2. You can also view the spanning tree status of the switch. A sample is shown below. 45 ...

  • Hawking HGMS224 - page 46

    3. You can change the settings for the STP parameters. Then click Apply . Parameter Description Priority You can change the priority value, which is a value used to identify the root bridge. The bridge with the lowest value has the highest priority and is selected as the root. Enter a number between 1 and 65535. Max Age You can change the max age v ...

  • Hawking HGMS224 - page 47

    4. The following parameters can be configured on each port. Click Apply after you have made the appropriate changes. Parameter Description Port Priority You can increase the priority level for a port to become the root port. The range is 0-255, and the default setting is 128. The lowest number has the highest priority. Path Cost This parameter spec ...

  • Hawking HGMS224 - page 48

    3. Monitored Port: The ports y ou want to monitor. All monitor port traffic will be copied to sniffer port. You can select max 25 monitor ports in the switch. User can choose which port that they want to monitor in only one sniffer mode. If you want to disable the function, you must select “None” in the “Analysis Port” category . 48 ...

  • Hawking HGMS224 - page 49

    5.4.10 SNMP/T rap Manager Any network management platform that is running the Sim ple Network Management Protocol (SNMP) can manage the switch, provided the Management Information Base (MIB) is installed correctly on the management station. SNMP is a protocol that governs the transfer of inform ation between management station and agent. 1. System ...

  • Hawking HGMS224 - page 50

    3. Trap Managers: A trap manager is a managem ent station that receives traps, which are the system alerts generated by the switch. If no trap manager is defined, no traps are issued. Create a trap manager by entering the IP address of the station and a community string. 5.4.1 1 Security Manager On this page, you can change the user name and passwo ...

  • Hawking HGMS224 - page 51

    5.4.12 802.1x Configuration System Configuration 802.1x makes use of the physical access characteristics of IEEE 802 LAN infrastructures in order to provide a means of authenticating and authorizing devices attached to a LAN port that has point-to-point connection characteristics, and of preventing access to that port in cases in which the authenti ...

  • Hawking HGMS224 - page 52

    Per Port Configuration In this page, you can select a specific port and configure the authorization state. You can select from a list of four authorization states for each port: Fu: Forces a specific port to be unauthorized. Fa: Forces a specific port to be authorized. Au: The state of a specific port is determined by the outcome of the authenticat ...

  • Hawking HGMS224 - page 53

    Misc Configuration In this page, you can change the default configuration for the 802.1x standard: Quiet Period: Used to define periods of time during which it will not attempt to acquire a supplicant (default time is 60 seconds). Tx Period: Used to determine when an EAPOL PDU is to be transmitted (default value is 30 seconds). Supplicant Timeout: ...

  • Hawking HGMS224 - page 54

    5.4.13 W eb Cluster This switch provides a new management tool for you to manage a group of LAN switches through a master switch. It is called the “Web Cluster” function. This function allows the manager switch (also called “master switch”) to fetch the web pages from the managed switches to the user ‘s browser. The MIS can store informat ...

  • Hawking HGMS224 - page 55

    There are 16+1 rows in the web cluster menu. The top row, with the deep blue background, indicates the master switch IP and cannot be modified. The other 16 rows, in a lighter blue background, can be added with managed switches by clicking Add/Del Switches . In the row, there is specific information about the managed switch: host nam es and their I ...

  • Hawking HGMS224 - page 56

    5.5 TFTP Firmwar e Update The following menu options provide some system control functions to allow you to update the rmware and remote boot switch system: are”. x new image.bin file by clicking Apply . te is completed, click Reboot to restart the switch. fi x Install the TFTP program (such as Turbo98, or Cisco TFTP) and then execute. x ...

  • Hawking HGMS224 - page 57

    5.6 Configuration Backup 5.6.1 TFTP Restore Configuration Use this page to set the FTP server address. You can restore the EEPROM value from here, but you u image. .6.2 TFTP Backup Configuration m st put the image back in the FTP server; the switch will download back the flash 5 se this page to set the TFTP server IP address. You can save the curre ...

  • Hawking HGMS224 - page 58

    5.7 Reset System In this page, y ou can reset the switch to its default configuration. The default value is shown elow. b .8 Reboot 5 this page, you can reboot the switch in software reset. In 58 ...

  • Hawking HGMS224 - page 59

    Console - 1K Xmodem Firmware Update s mode. So you must change the baud rate to 57600bps to download the firmware. here are two situations in which to use the 1K X modem to update the firm ware: . You can enter "1K X modem receiver m ode" by pressing any key within 5 seconds of the system power being turned on. . The system automatically ...

  • Hawking HGMS224 - page 60

    2. Press the “Connect” button and you will see “CCCC…”displayed on the console. Then go to Transfer > Send File . 3. Select 1K Xmodem under the Protocol item, and list the directory for the image file folder. Then click Send . 60 ...

  • Hawking HGMS224 - page 61

    4. Start downloading the image file. 5. Finish downloading the file and the switch system will update the firmware automatically. If the message “Update firmware…ok…” appears, the switch will reboot. Please change the baud rate to 9600bps. 61 ...

  • Hawking HGMS224 - page 62

    Out-of-band Terminal Mode Management . The switch also provides a serial interface to manage and monitor the switch. You can follow the steps outlined in the “Console Port Info” section of the web interface for using the Windows HyperTerminal program to link the switch. . You can type a user name and password to login. The default user name is ...

  • Hawking HGMS224 - page 63

    7.1 Main Menu The Switch Static Configuration: Allows you to configure the switch. Protocol Related Configuration: Allows you to configure the protocol function. Status and Counters: Displays the status of the switch. Reboot Switch: Allows you to restart the system or reset switch to its default configuration. TFTP Update Firmware: Uses TFTP to dow ...

  • Hawking HGMS224 - page 64

    7.2 Switch Static Configuration ou can press the Tab or Backspace keys to choose an item, and then press Enter to select the his section. to previous menu. es, ues. Previous Page>: Allows you to return to the previous page. Y item. The action menu, shown below, applies for configuration in t <Quit>: Allows you to exit the current page and ...

  • Hawking HGMS224 - page 65

    7.2.1 Port Configuration From this page, you can manipulate the status of every port. ress Spacebar to toggle between items. You can adjust the input rate (100K per unit). The valid range is 0-1000. ge is 0-1000. 1-1000: valid range of rate values. P 1. InRate (100K/unit): 0: disables rate control. 1-1000: valid range of rate values. 2. OutRate (10 ...

  • Hawking HGMS224 - page 66

    3. Enabled: You can enable or disable the ports. “No” indicates that the port is disabled. . Auto: You can set the auto-negotiation mode to either “Auto”, “N-way Force” or “Force” for each port. . Spd/Dpx: You can set the speed of ports 1-24 to either 100Mbps or 10Mbps. You can set the speed of ports 25 & 26 at either 1000Mbps, ...

  • Hawking HGMS224 - page 67

    7.2.2 Trunk Configuration Thi m of seven trunk groups. You can arbitrarily select up t nk group. 1. Select <Edit> on the “actions” menu 2. Press the spacebar to configure the m ember ports of a trunk group. You will also have to set the corresponding trunk groups between TRK1 and TRK7 to “Static” or “LACP”. “Static” – the st ...

  • Hawking HGMS224 - page 68

    6. All ports in the same static trunk group will be treated as a single port. So when you set the VLAN members and port configuration, they will be toggled on or off simultaneously. VLAN groups exist, all of the members of a static trunk group must be in the sam e VLAN roup. NOTE: If g 68 ...

  • Hawking HGMS224 - page 69

    7.2.3 VLAN Configuration The page below allows y ou to set the VLAN mode to port-based VLAN, 802.1Q VLAN, or “Disable”. 69 ...

  • Hawking HGMS224 - page 70

    NOTE : Whenever you change the VLAN settings, you will need to restart the switch. the VLAN mode is set to 802.1Q VLAN, you can set PVIDs, as well as ingress filtering 1 and gress filtering 2 in this section. . PVID (Port VID: 1-255): Type in the PVID. . Non-Member Drop: Same as Ingress Filtering Rule #1 on the web interface. Only forwards packets ...

  • Hawking HGMS224 - page 71

    7.2.3.1 Create a VLAN Group Ϭʳ Create a Port-Based VLAN Create a port-based VLAN and add member/nonm ember ports to it. 1. Select <Edit> . 2. VLAN Name: Type in a name for the new VLAN. 3. Grp ID: Type in the VLAN group ID. The group ID range is 1-4094. 4. Member: Press Spacebar to choose the VLAN members. There are two options: i. Member: ...

  • Hawking HGMS224 - page 72

    Ϭʳ Create an 802.1Q VLAN Create an 802.1Q VLAN and add tagged /untagged member ports to it. 2. VLAN Name: Type in a name for the new VLAN. in a VID between 1-4094. The default is 1. You can configure up to a. UnT AN group and outgoing frames are NO VLAN group and outgoing frames are c. NO: The port is NOT a member of this VLAN group. 6. Press Ctr ...

  • Hawking HGMS224 - page 73

    NOTE: If the trunk groups already exist, you can view them (ex: TRK1, TRK2…) after port 26 in the menu f ports and configure them as the mem bers of a VLAN. 7.2.3 d In th g 1. Press <E 2. Choose the edit or delete and then press Enter . 3. You can membe r por . 4. After ed g . o .2 E it/Delete a VLAN Group is pa e, you can edit or delete a VLA ...

  • Hawking HGMS224 - page 74

    . Pressing <Enter> once will complete deletion when in delete mode. . The VLAN Name and VLAN ID cannot be modified. . The default VLAN cannot be deleted. .2.3.3 Groups Sorted Mode this page, you can sort the VLAN groups by: .N a m e .V I D NOTE : 1 2 3 7 In 1 2 74 ...

  • Hawking HGMS224 - page 75

    The Edit/Delete a VLAN group page will display the result. Shown below is the page if sorted by name. 75 ...

  • Hawking HGMS224 - page 76

    Shown below is the page if sorted by VID. 7.2.4 Miscellaneous Configuration 76 ...

  • Hawking HGMS224 - page 77

    7.2.4.1 MAC Age Interval he valid range is 300-765 seconds. The default value is 300 seconds. Type the number of seconds that an inactive MAC address remains in the switch’s address table. T 77 ...

  • Hawking HGMS224 - page 78

    7.2.4.2 Broadcast S torm Filtering .P r e s s Spacebar to choose the threshold value. he valid threshold values are 5%, 10%, 15%, 20%, 25% and NO. The default value is 5%. 7.2.4.3 Max Bridge T ransmit Delay Bound 1. Max bridge transmit delay bound: Limits the queuing time of the packets in the switch. If enabled, the queued packets that exceed the ...

  • Hawking HGMS224 - page 79

    NOTE: Make sure “Max bridge transit delay bound control” is enabled before enabling “Low Queue Delay Bound” because “Low Queue Delay Bound” can only work when “Max bridge ansit delay bound control” is enabled. .2.4.4 Port Security port in security mode will be “locked” without permission of the address learning. Norm ally You ad ...

  • Hawking HGMS224 - page 80

    80 1. Select <Edit> . .P r e s s Spacebar to choose whether to enable or disable the item. .P r e s s Ctrl + A to go back to the action menu. . Select <Save> to save all configured values. .2.4.5 Collision s Retry Forever ollisions Retry Forever: Disable – In half-duplex, if collisions occur, the system will retry 2 3 4 5. You can pre ...

  • Hawking HGMS224 - page 81

    81 ...

  • Hawking HGMS224 - page 82

    7.2.5 Administration Configuration 82 ...

  • Hawking HGMS224 - page 83

    7.2.5.1 Change Username From this page, you can change the web manageme nt username. Type in the new username, and en press <Save> . .2.5.2 Change Password se this page; user can change web managem ent login password. th 7 U 83 ...

  • Hawking HGMS224 - page 84

    .2.5.4 IP Configuration From this page, you can configure the IP settings 7.2.5.3 Device Information From this page, you can configure the device information. 7 . 84 ...

  • Hawking HGMS224 - page 85

    N uration 7.2.6 Port Mirroring Config d networks. Traffic through ports can be monitored via one designated port. Traffic through ports can be monitored by one specific ort. That is, traffic going in or out of monitored ports will be duplicated into the monitoring port. Press Spacebar to change the configuration of each item. 1. Select <Edit> ...

  • Hawking HGMS224 - page 86

    7.2.7 Priority Configuration 86 7.2.7 he static priority is based on the port: if y ou set the port priority to high, incoming frames from is port will always be high priority frames. .1 Port S tatic Priority T th ...

  • Hawking HGMS224 - page 87

    7.2.7.2 802.1p Priority Configuration ueues are assigned high/low priority levels from 0-7. . Select <Edit> . 2. Press Spacebar to select the priority level mapping to high or low queue. 3. High/Low Queue Service Ratio H/L: You can select the ratio of high priority packets and low priority packets. 4. Press Ctrl + A to go back to the action m ...

  • Hawking HGMS224 - page 88

    7.2.8 MAC Address Configuration 7.2.8.1 S tatic MAC Address hen you add a static MAC address, it remains in the switch's address table, regardless of hether the device is phy sically connected to the switch. This saves the switch from having to re- arn a device's MAC address when the disconnected or powered-off device is active on the net ...

  • Hawking HGMS224 - page 89

    Add static MAC address ʳ ʳ 1. Press the <Add>, <Edit> key s to add static MAC addresses. ʳ 2. MAC Address: Enter the MAC address to and from which the port should permanently forward traffic, regardless of the device’s network activity. ʳ 3. Port num: Press Spacebar to select the port number. 4. VLAN ID: If tag-based (802.1Q) VLAN ...

  • Hawking HGMS224 - page 90

    Edit Static MAC Addresses 1. Press the <Edit> key. 2. Choose the MAC address that you want to modify and then press enter. ʳ ʳ ʳ ʳ 3. 4. +A to go back to the action menu, and then select <Save> to save all ʳ ʳ ʳ ʳ ʳ ʳ ʳ ʳ ʳ Press the <Edit> key to modify all the items. ʳ Press Ctrl configured values. 90 ...

  • Hawking HGMS224 - page 91

    elete a filter MAC address. ʳ 3. When pressing <Enter> once will complete deletion on delete mode. Delete Static MAC Address ʳ 1. Press <Delete> key to d 2. Choose the MAC address that you want to delete and then press enter. ʳ 91 ...

  • Hawking HGMS224 - page 92

    7.2.8.2 Filtering MAC Address MAC ad . Traffic is filtered based on the destinat s. Add filter MAC address 1. Press <Add>, <Edit> to add a filter MAC address. 2. MAC Address: Type the MAC address to filter. 3. VLAN ID: If tag-based (802.1Q) VLANs are set up on the switch, type the VID to associate with the MAC address. 4. Press Ctrl + A ...

  • Hawking HGMS224 - page 93

    ʳ Edit filter MAC address ʳ 1. Press the <Edit> key. 2. Choose the MAC address that you want to modify and then press enter. ʳ ʳ ʳ ʳ ʳ ʳ ʳ ʳ 93 ...

  • Hawking HGMS224 - page 94

    ʳ 3. Press <Edit> to modify all the items. ʳ 4. Press Ctrl + A to go back to the action menu, and then select <Save> to save all configured values. ʳ Delete filter MAC address ʳ ʳ 1. Press <Delete> to delete a filter MAC address. ʳ 2. Choose the MAC address that you want to delete and then press enter. ʳ 3. Pressing <Ent ...

  • Hawking HGMS224 - page 95

    95 ...

  • Hawking HGMS224 - page 96

    .3 Protocol Related Configuration 7 .3.1 Spanning-Tree Protocol 7 The Spanning-Tree Protocol (STP) is a standardized method (IEEE 802.1D) for avoiding loops in switched networks. When STP is enabled, it ensures that only one path at a time is active between any two nodes on the network. 96 ...

  • Hawking HGMS224 - page 97

    7.3.1.1 Enabling STP This page allows you to enable or disable the Spanning Tree function. Press Spacebar to select Enabled” or “Disabled”. “ 97 ...

  • Hawking HGMS224 - page 98

    7.3.1.2 STP System Configuration . You can view the spanning tree information about the Root Bridge on the left. . On the right, you can set new values for the STP parameters. OTE: For parameter descriptions, please see Section 2-4-8. 1 2 N 98 ...

  • Hawking HGMS224 - page 99

    7.3.1.3 Per Port Configuration 1. PortState: Displays the spanning tree status for each port – whether the port is forwarding or blocking. . PathCost: Specifies the path cost of the port that the switch uses to determine which ports are the forwarding ports. 4. Priority: This specifies the priority of port; you can make it more or less likely to ...

  • Hawking HGMS224 - page 100

    7.3.2 SNMP Any network management running the Simple Network Managem ent Protocol (SNMP) can be sed to manage the switch. Use this page to define management stations as trap managers and to nter SNMP community strings. You can also define a name, location, and contact person for the witch. u e s 100 100 ...

  • Hawking HGMS224 - page 101

    Options 7.3.2.1 System .P r e s s <Edit> . . System Name: Type a name to be used for the switch. 3. System Contact: Type the name of contact person or organization. 4. System Location: Type the location of the switch. 5. Press Ctrl + A to go back to the action menu. 6. Press <Save> to save the configured values. 1 2 101 ...

  • Hawking HGMS224 - page 102

    gs se this age to Add/ Edit/ Delete SNMP community strings. . Community Name: The name of current strings. . Write Access: Indicates if the rights are read-only or read-write. Restricted: Read-only - enables requests accompanied by this string to display MIB-object information. Unrestricted: Read-write - enables requests accompanied by this string ...

  • Hawking HGMS224 - page 103

    Add Community Name 1. Press <Add> --> <Edit> key. e right is restricted or unrestricted. Edit Community Name 1. Press <Edit> , choose the item that you want to modify, and then press Enter. 2. Community Name: Type the new name. 3. Write Access: Press Spacebar to set the rights to “Restricted” or “Unrestricted”. 2. Commu ...

  • Hawking HGMS224 - page 104

    C and then press enter. Delete Community Name 1. Press <Delete> key. 2. hoose the community name that you want to delete 3. When pressing <Enter> once will complete deletion in delete mode. 104 ...

  • Hawking HGMS224 - page 105

    7.3.2.3 At r a p ted by the switch. by entering the IP address of the station and a community string. Add SNMP trap manager 1. Press <Add> , <Edit> to add the trap manager. 2. IP: Type the IP address. 3. Community Name: Type the community name. 4. Press Ctrl +A to go to the actions menu. Press <Save> key to save all configured val ...

  • Hawking HGMS224 - page 106

    Edit trap managers .P r e s s <Edit> key, and then choose the item that you want to modify. . IP: Type the new IP address . Community Name: Type the community name. .P r e s s Ctrl +A go to actions line, press <Save> key to save all configure. 1 2 3 4 106 ...

  • Hawking HGMS224 - page 107

    Delete trap manager 1. Press the <Delete> key. 2. Choose the trap manager that you want to delete and then press Enter . 3. Pressing <Enter> once will complete deletion in delete mode. 107 ...

  • Hawking HGMS224 - page 108

    7.3.3 GVRP GVRP ( R l) VRP allows automatic VLAN configuration between the switch and corresponding nodes. For xample, if the switch is connected to a device with GVRP enabled, you can activate this setting to allow dynamic VLAN configuration information to be processed by the switch. If a device sends a GVRP request using the VID of a VLAN defined ...

  • Hawking HGMS224 - page 109

    7.3.4 IGMP The Internet Group Management Protocol (IGMP) is an internal protocol of the Internet Protocol P) suite. (I This page you can enable / disable the IGMP support. . Select <Edit> . .P r e s s Spacebar to choose enabled / disabled. .P r e s s Ctrl + A to go back to the action menu. . Select <Save> to save configured values. 1 2 ...

  • Hawking HGMS224 - page 110

    7.3.4.1 LACP (Link Aggregation Control Protocol) Note: All ports support LACP dynamic trunking groups. If connecting to a device that also supports LACP, the LACP dynamic trunking group will be created autom atically. 7.3.4.2 Working Port Setting This page can set the actual work ports within the trunk group. This page can configure and view the LA ...

  • Hawking HGMS224 - page 111

    1. Select <Edit> . 2. Group: Displays the trunk group ID. . LACP Work Port Num: The maximum number of ports that can be aggregated at the same time. If the group is LACP static trunking, the excess ports are standby and able to aggregate if work ports fail. If the group is local static trunking, the num ber of ports m ust be the sam e as the ...

  • Hawking HGMS224 - page 112

    7.3.4.4 LACP S tatus lational information here. LACP trunk group When you’re setting trunking group, you can see the re Static trunk group 112 ...

  • Hawking HGMS224 - page 113

    <Quit>: Exit this page and return to previous menu. Previous Page>: Return to previous page to view. .3.5 802.1x Protocol < <Next page>: Go to next page to view. 7 rom this page, you can configure and view the 802.1x status. F 113 ...

  • Hawking HGMS224 - page 114

    7.3.5.1 Enable 802.1x 1. Select .P r e s s .P r e s s 4. Select .3.5.2 802 <Edit> . Spacebar to choose enabled/disabled. Ctrl + A go back to the action menu. <Save> to save configure value. .1x System Configuration 2 3 7 114 ...

  • Hawking HGMS224 - page 115

    1. Press <Edit> . rver IP Address: the IP address of the authentication server. 3. Shared Key: A key shared between this switch and the authentication server. 4. NAS, Identifier: A string used to identify this switch. 5. Server Port: The UDP port number used by the authentication server to authenticate. 6. Accounting Port: The UDP port number ...

  • Hawking HGMS224 - page 116

    3. Tx rmine when an EAPOL PDU is to be transmitted (default value is 30 sec ) 4. Sup a nt h e supplicant and authentication server (default value is 30 seconds). 5. Ser T authenticator and authentication server (default value is 30 seconds). 6. Re- h before a s (default value is 2 times). 7. Re- of seconds between periodic re-a is 3600 seconds). .P ...

  • Hawking HGMS224 - page 117

    7.4.1 Port Status ink Status: Indicates whether the port is linked or not linked. Rate: Displays the input rate control (100K/unit) setting value. utRate: Displays the output rate control (100K/unit) setting value. nabled: Indicates whether the port is enabled or disabled. This depends on the user setting. nabled” will be displayed as “Yes”, ...

  • Hawking HGMS224 - page 118

    <Quit> : Exit the “Port Status” page, and then return to the previous menu. Previous Page>: Displays the previous page. < <Next page>: Displays the next page. .4.2 Port Counters 7 he following information provides a view of the current status of the unit. ious page. T <Quit> : Exit the “Port Status” page and return t ...

  • Hawking HGMS224 - page 119

    7.4.3 System Information MAC Address: The unique hardware address assigned by the manufacturer. irmware Version: Displays the switch’s firmware version. SIC Version: Displays the switch’s hardware version. ys the board number. erial number: Displays the serial number assigned by the manufacturer. on module card mode. odule 1 information: Displa ...

  • Hawking HGMS224 - page 120

    7.5 Reboot Switch .5.1 Default 7 esets the switch to its default configuration. For default settings, please see Section 2-4-14. 7.5.2 Restart R Reboot the switch in software reset. 120 ...

  • Hawking HGMS224 - page 121

    7.6 TFTP Firmware Update his page provides you with the option to update the firmware, restore the EEPROM values, or pload current EEPROM values. T u 121 ...

  • Hawking HGMS224 - page 122

    7.6.1 TFTP Firmware Update This page allows you to use TFTP to update the firmware. 1. Start the TFTP server, and copy the firmware update version image file to the TFTP server. 2. Press <Edit> on this page. 3. TFTP Server: Type the IP of the TFTP server. 4. Remote File Name: Type the image file name. 5. Press Ctrl + A to go to the action men ...

  • Hawking HGMS224 - page 123

    123 . Start the TFTP server. 2P 3 TFTP server. 4 5 6 to download. 7 ownloading as well. 8R 1 .r e s s <Edit> on this page. . TFTP Server: Type the IP of . Remote File Name: Type the image file name. .P r e s s Ctrl + A go to action line. .P r e s s <Save> , and the image file will begin . When saved successfully, the image file will hav ...

  • Hawking HGMS224 - page 124

    7.6.3 Backup Configure File this page, you can save the current EEPROM value to the image file. Then go to the update onfigure page to restore the EEPROM value. the IP of the TFTP server. 4. Remote File Name: Type the image file name. 5. Press Ctrl + A to go back to the action menu line. 6. Press <Save> , and the image file will begin to down ...

  • Hawking HGMS224 - page 125

    5.1 VLAN Application Used with Switch by formation and avoiding the complexity and heavy rocessing requirements of Layer 3 IP based routers. s a result, each group of stations connected to separate segmented ports forms a different olated broadcast domain. The broadcast sharing ports should be used to connect servers and ther common services, such ...

  • Hawking HGMS224 - page 126

     Offers security by completely isolating from each other the different broadcast  Network administrators can easily "fine tune" the network. ou can group users according to som e shared characteristic, such as a common business nction or a common protocol. A single switch ma y have several independent VLANs ithin it. On the followin ...

  • Hawking HGMS224 - page 127

    127 127 ...

  • Hawking HGMS224 - page 128

    5.2 Trunking Application Used with Switch runking allows you to increase the available bandwidth between switches by grouping ports into trunk. Trunking can also be used to connect a server to switches if higher bandwidth service is quired. You can use trunking to improve the throughput between segments. Moreover, this itch provides trunking with a ...

Manufacturer Hawking Category Switch

Documents that we receive from a manufacturer of a Hawking HGMS224 can be divided into several groups. They are, among others:
- Hawking technical drawings
- HGMS224 manuals
- Hawking product data sheets
- information booklets
- or energy labels Hawking HGMS224
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hawking HGMS224.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hawking HGMS224, service manual, brief instructions and user manuals Hawking HGMS224. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hawking HGMS224.

Similar manuals

A complete manual for the device Hawking HGMS224, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hawking HGMS224 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hawking HGMS224.

A complete Hawking manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hawking HGMS224 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hawking HGMS224, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hawking HGMS224, that we can find in the current document
3. Tips how to use the basic functions of the device Hawking HGMS224 - which should help us in our first steps of using Hawking HGMS224
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hawking HGMS224
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hawking HGMS224 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hawking HGMS224?

Use the form below

If you did not solve your problem by using a manual Hawking HGMS224, ask a question using the form below. If a user had a similar problem with Hawking HGMS224 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)