English dropdown-ico

Manual National Instruments FP-1000

12 pages 0.31 mb
Download

Go to site of 12

Summary
  • National Instruments FP-1000 - page 1

    FieldPoint ™ is a trademark of National Instruments Corporation. Product and company names are trademarks or trade names of their respective companies. 321697A-01 © Copyright 1997 National Instruments Corp. All rights reserved. July 1997 FP-1000 FieldPoint RS-232 Network Module Highlights • RS-232 interface to host computer • Built-in isolat ...

  • National Instruments FP-1000 - page 2

    2 DIN Rail Mounting NOTE: Terminal bases must be connected to the network module before applying power to the module. Do not connect or disconnect terminal bases while power is applied to the network module. The FP-1000 has a simple rail clip for mounting reliably onto a standard 35 mm DIN rail. To install the FP-1000 to the DIN rail, follow these ...

  • National Instruments FP-1000 - page 3

    3 4. Add terminal bases to the DIN rail with their local bus connectors firmly mated to the FP-1000 local bus connector. The FP-1000 is shipped with a protective cover over the local bus connector. Remove this protective cover, and place it over the local bus connector of the last terminal base in the stack. Figure 3 shows an installed FP-1000 netw ...

  • National Instruments FP-1000 - page 4

    4 Figure 4. RS-232 Connector Pinout Up to 24 additional FP-1001 network modules can be connected to this FP-1000 module by using the built in RS-485 repeater. This repeater makes the RS-485 port of the FP-1000 appear to the additional FP-1001 modules as if it were an RS-485 port of the host computer. The pinout of the RS-485 connector is shown in F ...

  • National Instruments FP-1000 - page 5

    5 These connections are shown in Figure 6. Figure 6. Typical Signal Connections with One FP-1000 Connected to Multiple FP-1001 Network Modules Figure 6 also shows the use of 120 Ohm termination resistors. An RS-485 network must be terminated at each end of the network, but not anywhere else. Termination resistors should be installed between the RX ...

  • National Instruments FP-1000 - page 6

    6 module is at address 22, and so on. A terminal base is assigned a network address whether an I/O module is inserted into it or not. Figure 7. Address and Baud Rate Switch Table 1 shows the possible switch positions and the corresponding address of the FP-1000. Table 1. Network Address Switch Settings Switch Positions 1-5 Network Module Address (D ...

  • National Instruments FP-1000 - page 7

    7 Switches 6-8 set the baud rate of the FP-1000. Table 2 shows the switch positions and the corresponding network baud rates. 70 200 80 210 90 220 100 230 110 240 120 Other Settings Not Allowed Table 2. Baud Rate Switch Settings Switch Positions 6-8 Network Module Baud Rate Switch Positions 6-8 Network Module Baud Rate 300 19200 1200 38400 2400 576 ...

  • National Instruments FP-1000 - page 8

    8 Powering the FP-1000 NOTE: Terminal bases must be connected to the FP-1000, and the baud rate switch must be set, before power is applied to the FP-1000. An 11-30 VDC power supply is required by each FieldPoint stack. The network module filters and regulates this supplied power and provides power for all the I/O modules in the stack. Therefore yo ...

  • National Instruments FP-1000 - page 9

    9 Specifications Network ports ................................... 1 RS-232 port, 1 RS-485 repeater port Baud Rates ........................................ 300, 1200, 2400, 9600, 19200, 38400, 57600, 115200 (switch selectable) Communication parameters .............. 1 start bit, 8 data bits, 1 stop bit, No parity RS-485 isolation ................. ...

  • National Instruments FP-1000 - page 10

    10 Mechanical Dimensions Figure 9 shows the mechanical dimensions of the FP-1000. Figure 9. Mechanical Dimensions 4.31 [109.5] 3.58 [90.9] 4.19 [106.4] FP1000.fm Page 10 Thursday, July 31, 1997 8:49 AM ...

  • National Instruments FP-1000 - page 11

    FP1000.fm Page 11 Thursday, July 31, 1997 8:49 AM ...

  • National Instruments FP-1000 - page 12

    FP1000.fm Page 12 Thursday, July 31, 1997 8:49 AM ...

Manufacturer National Instruments Category Network Router

Documents that we receive from a manufacturer of a National Instruments FP-1000 can be divided into several groups. They are, among others:
- National Instruments technical drawings
- FP-1000 manuals
- National Instruments product data sheets
- information booklets
- or energy labels National Instruments FP-1000
All of them are important, but the most important information from the point of view of use of the device are in the user manual National Instruments FP-1000.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals National Instruments FP-1000, service manual, brief instructions and user manuals National Instruments FP-1000. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product National Instruments FP-1000.

Similar manuals

A complete manual for the device National Instruments FP-1000, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use National Instruments FP-1000 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of National Instruments FP-1000.

A complete National Instruments manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual National Instruments FP-1000 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the National Instruments FP-1000, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the National Instruments FP-1000, that we can find in the current document
3. Tips how to use the basic functions of the device National Instruments FP-1000 - which should help us in our first steps of using National Instruments FP-1000
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with National Instruments FP-1000
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of National Instruments FP-1000 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning National Instruments FP-1000?

Use the form below

If you did not solve your problem by using a manual National Instruments FP-1000, ask a question using the form below. If a user had a similar problem with National Instruments FP-1000 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)